Search Documents

By Geo. A. Brown

This paper was written from conditions existing in the Cumberland Mines of The Union Pacific Coal Co., with my impressions and cause of same. These mines are located on a branch line of the 0. S. L. R. R., about sixteen miles south of Kemmerer, Wyoming. The mines are the property of The Union Pacific Coal Company with headquarters at Rock Springs, Wyo. There are two mines, No. 1 and No. 2, located about two miles apart in a seam of coal averaging about 16 feet thick which is split with a parting of rock from 4 feet to G feet from the bottom, averaging from 4 inches to 5 feet thick, mostly of soft fire clay, with an average pitch of 21 degrees to the west. The lower coal below the fire clay band being of a soft nature, much softer than the coal above it. The cover or roof next to the coal is of a massive sandstone formation from 4 feet to 60 feet thick while the floor of the seam is of a soft fire clay as far down as has been prospected. These mines are also of a dry and dusty nature, they generate lots of fire damp and are subject to fires from numerous causes. These mines were opened up in 1900 with five openings each, Main Slope, North and South Manways and North and South Aircourses driven parallel directly on the pitch of the seam which is fairly regular, entries being turned North and South at right angles off the slope about 300 feet apart. The entries were driven double 10 feet wide with chain pillars from 20 feet to 30 feet thick. The main entries are used for haulage and main intake, back entries for return aircourses. Rooms are turned on 50-foot centers and 20 feet wide, directly on the pitch Galvanized sheet iron chutes are used in the rooms. The slopes were driven down in No. 1 mine about 4,000 feet, in No. 2 mine about 5,000 feet where the cover would be about 1,400 feet in No. 1 mine and about 1,700 feet in No. 2 mine approximately. When a point about 2,000 feet on the slope had been reached with cover, 600 or 700 feet squeezing became noticeable on the entries and room pillars with slight bumps which extended clear to the upper entries of the mines and continued to get worse as the mines got deeper and with more cover as no pillars had been removed at this time. It should be stated here that faulty ground was found on the south side of No. 2 mine and on the north side of No. 1 mine, in some places looking like a fault of a down throw, some places like a want and other places like an erosion. The latter theory seems to be correct from prospecting and drilling. The mining of entries and rooms became more difficult with more squeeze and bumps of increased pressure which closed entries and aircourses and finally caused the lower workings of the mine to be abandoned. It was then decided to open up the entries from the 6th up, or approximately half way up the slope. The opening of these entries was started with the intention of extracting pillar coal but considerable danger was met with for the entries .were squeezed tight and when they were disturbed, bumps and squeeze conditions had to be contended with, also gas and fires due to the continued grind on the pillars due to overhead pressure bringing on friction which caused innumerable fires to start in the bottom coal. Bumps being so extensive at times as to close up aircourses for 500 or 600 feet, also discharge timber, coal and rock from the rib of slope and entries for hundreds of feet, dislodging tracks and throwing mine cars around just as if an explosion had taken place, filling places with gas and throwing dust into the atmosphere so that you could cut it with a knife. It became necessary to discontinue the use of black powder and naked lights entirely as a safety precaution. Permissible Powder Monobel No. 5 and Wico Electric Safety Lamps were installed. All coal was shot off the solid whenever it was necessary to shoot. ' In opening up these entries it was found that practically all of the weight was centered on room pillars up to the first crosscut chain pillars and barrier pillars between top of rooms of entry below and the one above which averaged 30 feet thick and in all practically 120 feet of ground. The rooms were mostly open from the first crosscut up to the face which showed that the points mentioned had taken the weight. It was found impossible in some of these entries to drive double entries again as the bumps and squeeze made it impossible to maintain them. This made ventilation quite a problem, small booster fans and flexoid tubing being used for ventilation until one entry could be connected with the one above which has solved most of our ventilation problems so far.

Jan 1, 1924

By J. H. Emrick

When I was asked to read a paper to you, I wondered what idea I could bring before you which would be interesting and which would be helpful in your work in operating coal mines. The Institute has been studying ways and means of increasing the safety and efficiency of mine operations. Almost every subject along this line has been discussed from time to time. In thinking the matter over it occurred to me that there was one thing used by practically all coal mining companies in considerably large quantities and which in many cases does not receive the attention it should. It is the cutter bit placed in the cutter chains on coal mining machines. Coal mining machines have been repeatedly improved during the last twenty-five years until their efficiency and convenience have reached a high level. The generating units making electrical power to operate them also have been developed to a similar degree. This machinery has been in- stalled at a great expense to coal mining companies and the installation made for the sole purpose of pulling coal cutter bits through coal. Why not then give these cutter bits some attention so as to see that they do their work as efficiently as their driving and propelling units? The consideration of this question easily divides itself into three principal parts-First, the kina of steel out of which to make the bit; Second, the proper form or shape to give it; and Third, the tempering of the bit. Let us discuss them in that order. There have been tried at different times' various grades of steel for cutter bit uses. The cheaper steels, having a very low carbon content (.10 to .30 per cent carbon) have proved un- satisfactory because such steel cannot be tempered so as to produce a satisfactory cutting tool. Because of the low carbon content, it cannot be hardened to retain its cutting edge. It dulls quickly, bends easily on striking any hard obstruction in the coal, and so requires constant resetting to its original form. The high priced alloy steels when properly shaped and tempered will give a bit that would make a clean, even cut in the coal if no impurities were encountered. Such a condition is rarely found. Alloy steel is quite brittle and on striking impurities, such as sulphur balls or a sand spar, is readily broken and so the loss of material through these broken bits and the high price paid for it more than offset all the other advantages which this steel has shown in cutting. Experience has shown that steel having approximately .70 per cent carbon and from .25 to .35 per cent manganese will give the most economical results. Some mines have obtained better results by using a steel of slightly higher carbon content and in some cases a grade of tool steel has been used. The disadvantage of using a steel having too much carbon is that it can easily be spoiled in the black- smith shop by overheating. Steels having a carbon content of about .70 per cent have a sufficiently wide range of temperatures at which they can be forged and hardened so that with ordinary care and attention they are not likely to be burned. Steel of this quality, therefore, has been found to be the most practicable because of its reasonable cost, ease in working and tempering and general durability. In the early days of mining machines, comparatively few bits were used because each machine required but a few bits because there were but

Jan 1, 1925

By Richard M. Whiting

Thank you very much for that introduction. I spent part of my early career in the coal industry here in Colorado, and I am always happy to return. In such a beautiful setting, it seems out of place to talk about "Improving the Climate". But in our work-a-day worlds, we know the climate for the coal industry is something less than picture perfect. But unlike Mother Nature's climate, there are some things we can do about the climate for coal. Today, I want to talk to you about sonic of the activities that we are engaged in... and that you can support... to improve that climate. A number of challenges and opportunities face our industry. I will try to set the stage for this conference by briefly describing the current climate for coal - which is indeed very challenging. I will then outline some of the steps we are taking to broaden our base to include our allies in the rail and electricity industries and the public at large.

Jan 1, 2000

By C. P. Crawford

In the current issue of Link-Belt News is this quotation: "Advancing waves of other people's progress sweep over the unchanging man and wash him out." As we look over the industrial world today we are struck by the many waves which are sweeping over backward industries. Mergers are being consummated in all lines of endeavor. General Motors are making radios and the Bendix Brake Company are making airplanes. Railroads which twenty years ago were called to account by the Federal Government for their efforts to form combinations are today being ordered to combine. But what is of immediate concern to the coal industry is the fact that there is now in existence or in project a total of 3,641 miles of pipe lines to carry natural gas to most of the country's industrial centers. This is the wave of progress which is sweeping toward you and me. If we are to grasp the significance of these many changes, we must widen our vision so that we may learn some- thing from 'the other fellow's experience. The first lesson is that cost of production alone is not a measure of profit. It is an interesting fact that the production of an article represents a definite loss until that article has been sold for a price in excess of its total cost, and the money is in the hands of the producer. If this is true, then the selling price is more important than the production cost.

Jan 1, 1930

By A. L. Jones

The subject assigned to me of "The Power" Problem of the Mine" is so broad that I have decided to confine myself to the question of the power supply itself, rather than the application of electricity throughout the property. We will look over certain economic aspects of the problem, particularly in the way it affects the mine manager or executive and his attitude toward the power plant. The accepted method of power application to the mine is by electric power, and the experience of each of you is that the job is never complete as you are always undertaking some further electrification which necessitates the stiffing up the power house to care for the additional load. The mine executive, then, is wrestling almost continuously with the problem of his power plant. Either it is overloaded and must be enlarged and rebuilt; or its operating costs are excessive; or it breaks down and limits coal output; or some one wants to sell new and improved machinery, until the manager almost hates the thought of such a restless part of his property. If he purchases power, every day new uses for it seems to be found. In many ways this unrest is due to short-sighted policy toward the problem, and the tendency when the problem of extension has to be met, to dispose of it in the cheapest way and without thought as to where the future is leading. The day when each opening had its own boiler plant, steam hoist, steam driven fans, steam pumps, steam loaders, etc., seems to be far behind us. The recognized method of power distribution today is by electric power, except for rather limited applications of compressed air; most of which is electrically compressed. During fifteen years contact with mines of Colorado and Wyoming the writer has seen nearly every mine power house double or triple in capacity or abandoned in favor of purchased power, worn. out and inefficient machinery thrown out, isolated boiler plants dropped, seam pumping at great depth changed to electric drive, all resulting in greatly reduced labor and fuel costs. Power costs, which in such isolated plants were considered normal, would be unthinkable today. One property where the main power supply was by compressed air from steam driven com¬pressors used under boilers 8.35 per cent of all the coal mined. The cost of power was 12 1/2 cents per ton of coal mined. Another property of four openings, each with its own boiler plant and usual equipment of hoists, pumps, etc., had a power cost of 10.3 cents for each ton mined; and these were days when you did not get very high prices for coal. Another property operating two mines mostly by steam used 11.1 per cent of the coal output under their own boilers and the power cost was 19.45 cents for each ton mined. Each of these properties is now electrified and power costs are from 3 to 4 cents per ton, and the fuel burned runs from 1 to 2 per cent of the output. With the broadening market and high prices for slack coal and the high prices for labor in boiler and engine rooms, the cost of steam is reaching a high figure, and efforts must be made to keep this down, by more efficient steam production and by utilizing this steam in better machinery which will increase the work done by each pound of steam. It must not be overlooked either, that the plant which is very wasteful of fuel is usually a pretty old one and one far from reliable. In a general way the more efficient the plant, the greater its reliability. Ample and reliable power supply means ability to get out coal when there is a market. The increasing use of purchased power is largely due to changing conditions which are tending constantly to push up the cost of power, unless the most efficient machinery is used and large scale production possible. The

Jan 1, 1923

By Steve Leer

Pick then introduced the convention keynote speaker, Steven Leer, President and Chief Executive Officer of Arch Coal. Following the morning coffee break, Pick introduced Howard Goodman to present the Fourth Annual Safety Awards. [ ]

Jan 1, 2001

By K. L. Marshall

A facetious title was purposely given this talk, so that a formal paper would not be expected. TWO or three days ago, while discussing with Mr. Dickinson some of the details of the dust explosion demonstrations we are planning for this coming Saturday, I remarked that we would like to have as many people as possible see some samples of 20 and 200 mesh dust, so they would more fully understand just what was causing the explosions. Mr. Dickinson requested that I bring samples and screens and in this informal manner, give you all a ".close-up" of coal dust which is considered in Explosion Hazard reports. While sampling mines, for road, rib, and roof dust, in connection with safety service and hazard reports which the Bureau of Mines Engineers make at the request of coal operators, I have often been assisted by under- ground mine officials or other men of many years experience and on almost every occasion, while we were carefully brushing the very fine dust from timbers or coal surfaces, they would make some remark such as: "never had noticed this kind of dust, didn't know it was here", or "well, that's the first time I really understood what all 'this dust talk was about." Such experience makes me believe that the much published terms, 20 mesh and 200 mesh are just numbers to the great majority of both miners and operators. We are now going to have lesson one in the primer of coal dust explosions and I want to say, in all sincerity that a complete course in the hazards of mining is deserving of a place in the curriculum of the best mining schools of this country. Sample No. 1 is fine coal and dust and is a fair sample of what can be found every where in rooms and entries of a mine, as it is too small to be gathered up with a shovel and is left in the ordinary mining at the faces and is spilled along the entries in haulage. In this you will see some quarter inch coal, much eighth and sixteenth inch coal, in fact those are the sizes I find many people have in mind when they are asked about the dust made in mining. Although the sizes mentioned are the ones which seem to almost entirely make up this sample, such is not the case, for from 10 to 20% of such a sample will usually pass this 20 mesh screen and in Sample No. 2 we have 20 mesh dust. Result of many tests, supports .the statement of the coal mining division of the Bureau, that it is quite probable that coal over 20 mesh does not take part in any but the most violent of explosions and that all dust under 20 mesh may take part in any explosion. The largest particles in this sample will not be over .03 inches in their largest dimension and a pound of dust to a foot of average heading is very easily found in most every mine I have visited and usually a great deal more can be readily gathered up. It was .found early that the finer the dust the more dangerous it was for a given coal. So for the early explosion tests conducted by the Bureau a commercial pulverizer was used and it turned out a 20 mesh dust of which about 75% would pass 200 mesh. Some men question whether the ordinary mining methods made such a dust and so doubted the explosibility of the dust in their own mines. The question was well taken, and hundreds of dust samples were taken by the field men of the Bureau to determine the kind of dust being made in all methods of mining and all classes of coal. The result of such sampling showed some coals. resisted breakage more than others and that actual mine road dust, through 20 mesh, would show from 10 to 20% through 200 mesh, and for actual rib and roof dust through 20 mesh, they would get from 20 to 40% of 200 mesh dust. In testing the

Jan 1, 1924

will be held at COSMOPOLITAN HOTEL DENVER COLORADO June 3,4,5, 1931

Jan 1, 1930

The 1939 meeting will be held in Salt Lake City, the exact date to be announced later. If you have any suggestions for the place or program, send them to the Secretary at once.

Jan 1, 1938

Houston T. Aars Carter Mining Co. Sundance Rt. Moorcroft, WY 82716 Charles R. Ahlbrecht Western States Surveying Inc. 7030 So. Yosernite Englewood, CO 801 12 Dean Albon Monsanto Co. 800 No. Lindberg St. Louis, MO 631 67 Robert Anderson Mobil Oil Producing Inc. POB 17772 Denver, CO 8021 7 Stephen P. Antony Orbital Engineering 6789 So. Yosernite Englewood, CO 801 12 David Ariotti Boyle Mining Engineering Service Rt. 1 Box 15M Helper. UT 84526 Douglas Auck Falkirk Mining Co. 103 McKinley Ave. Underwood, ND 58378 Roger Backrnan N. D. Crockett & Assoc. 3467 Sorenson Way Salt Lake City, UT 84109 Richard Bailey Continental Conveyor & Equip. Co. 602 Park Point Drive Golden, CO 80401 Earl W. Baker Baker & Co. 4965 Jackson St. Denver, CO 80216 Allen P. Barber San Juan Coal Co. 705 Ocio Farrnington, NM 87421 Edward Barker Process Equipment Builders POB 7506 Paducah, KY 42001 Larry Barton Carter Mining Co. 101 5 Teewinot Circle Gillette, WY 82716 Hugh Bastian American Carbide Corp. POB 2650 Ronald N. Batdorf Monsanto Co. Box 701 Saratoga, WY 82331 Georgetown, KY 40321 Doris A. Bauer Mobile Oil Corp. POB 17772 Denver, CO 80217 Jan Beam Blount International Ltd. 2570 So. Dayton Way #E-308 Denver, CO 80231 Mac Beaudry Falkirk Mining Co. 1029 Cannon Ln. Washburn, ND 58527 R. C. Beerbower Gates Engineering Co. Drawer A Beckley, WV 25801

Jan 1, 1982

[Mr. Houston T. Aars Carter Mining Co PO8 3007 Gillette, WY 82716 Mr. Jay Abbott Union Supply Co 7458 S Jackson St Littleton. CO 80122 Mr. Ronald H. Achziger Midwest Rbr & Sply Co 6404 E 39th Ave Denver, CO 80207 Mr. Randy Acre Dorchester Coal Co 9350 E Arapahoe Rd Englewood, CO 80112]

Jan 1, 1983

[Mr. Jay Abbott Union Sply Co 7458 S Jackson St Littleton. CO 80122 Mr. Ronald H. AchZlger Midwest Rbr 6 Sply Co 6404 E 39th Ave Denver, CO 80207 Mr. Randy Acre Dorchester Coal C 9350 E Arapahoe Rd Englewood, CO 80112 Mr. Dell H. Adams Kenerco Corp 5480 Swanton Dr Lexington, KY 4051 Mr. Robert S. Affleck Anderson Mavor (USA) Ltd RD #1 Box 140-Lake R Bradford Woods, PA 15015]

Jan 1, 1984

At the Annual Meeting of the RMCMI Board of Directors held June 29, 1985, the following amendments to the corporation bylaws Article III were made: Section 2. Advisory Board. There shall be an Advisory Board of Directors which shall be com- posed of all former presidents of the corporation and of the unincorporated association, also known as The Rocky Mountain Coal Mining Institute, of which the corporation is the successor. The Advisory Board shall periodically review the philosophy and policies of the corporation and make recommendations concerning the same to the Board of Directors. The Advisory Board shall hold an annual meeting at the same place as and immediately pre- ceding the annual meeting of the members in each year and written notice stating the place, day, and hour of the meeting shall be given or mailed to each member of the Advisory Board at least thirty days prior to the date fixed for such annual meeting. The annual meeting of the Advisory Board shall be for the purpose of electing a chairman from among its members and the person so elected chairman shall also serve as a member of the Board of Directors of the corporation. The Advisory Board shall meet at such other times and conduct its affairs in such a manner as it shall determine from time to time by resolution. Section 4. Regular Meetings. A regular meeting of the Board of Directors shall be held immediately following the annual meeting of the members, at the site of the annual meeting of the members, the day and time to be fixed by the Board of Directors at its annual meeting immediately pre- ceding the annual meeting of the members in each year, without the necessity of any other or advance notice. Such regular meeting of the Board of Directors shall be for the purpose of considering committee appointments, and for the transaction of such other business as may come before the meeting. A regular meeting of the Board of Directors shall also be held in the Fall of each year following the annual meeting of the members and written notice stating the place day and hour of the meeting shall be given or mailed each member of the Board of Directors at least thirty days prior to the date fixed for such regular meeting. Such Fall regular meeting of the Board of Directors shall be for the purpose of receiving the treasurer's annual financial report of the previous fiscal year as reviewed and approved by the auditor, to take action on the budget, and for the transaction of such other business as may come before the meeting. Section 8. Standing Committees. The Board of Directors may create by resolution adopted by a majority of the entire Board of Directors, a Bylaws and Resolutions Committee, a Nominating Committee, a Finance Committee, and one or more other committees each of which shall consist of two or more directors and which shall have and may exercise such authority in the management of the corporation as shall be provided in such resolution or in these bylaws. Section 9. Ad Hoc committees. The Board of Directors from time to time may by resolution create a Membership Committee, a Scholarship Committee, an Education Committee, various convention committees, and one or more other committees each of which shall consist of members of the corporation and which shall have and may exercise such authority, other than in connection with the management of the corporation, as the Board of Directors may determine. MINUTES of the Rocky Mountain Coal Mining Institute 81 st Member Annual Business Meeting July 2, 1985 The 81st Annual Business Meeting of the mem¬bers of The Rocky Mountain Coal Mining Institute was called to order by the president, Charles W. Margolf at 1:35 p.m. Tuesday, July 2, 1985 in the Windom Peak Room of the Tamarron Resort near Durango, Colorado. Thirty members were present and a quorum was established. It was moved by Bill Balaz, seconded and car¬ried to dispense with the reading of the minutes as these were published on pages 67 thru 77 of the 1984 issue of the Proceedings. The chair called for reports of the various com¬mittees and these reports will be placed on file in the RMCMI Office. Bylaws and Resolutions. Chairman Loren V. Linville reported that the Board of Directors had adopted changes to Article III, Sections 2, 4, 8 and 9 calling for clarification of Ad Hoc and Standing Committees as well as setting forth a purpose for the Advisory Board meetings and stating a time for an annual meeting. He further reported that the Board had passed three resolutions: (One) Noting the passing of these members since the last conven¬tion - Einar M. Arentzen, Gerhardt A. Benne¬witz, Claude P. Heiner, Raymond A. Johnson, Vard H. Johnson, P. T. Schonstrom, Augusta F. Whiteside and Edward Wiemann; (Two) Of appreciation to the officers, chairmen and their commit-

Jan 1, 1985

[ACC, Inc. Bucyrus-Erie Company CINCO (Coal Industry Consultants, Inc.) Coal Magazine Colowyo Coal Company Coors Ceramic Company Crane & Hoist Sales, Inc. Cummins Power. Inc. Cummins Southwest, Inc. Cyprus Coral Company Denver & Rio Grande Western Railroad Company Energy Fuels Corporation FMC Corp.- MHE Division Ford. Bacon & Davis Inc. T.J. Gundlach Machine Company Hemscheidt American Corp. GH Hensley Industries Honnen Equipment Company Jennmar Corporation Soy Technologies, Inc. K&P Sales Engineers, Inc. Kennametal, Inc. Kerr McGee Coal Corp. McLanahan Corporation National Mine Service Company Peabody coal Company Pitrsburg & Midway Coal Mining Co. Pyramid Parts, Div. American Alloy Ramsey Technology. Inc. Roberts & Schaefer Company Santa Fe Pacific Coal Corporation Scandura. Inc. Tamarron Resort TIC (The Industrial Company) Tribol Utah Power & Light Western Energy Company]

Jan 1, 1988

BHP-Utah International, Inc. Coal Magazine Crane & Hoist Sales, Inc. Cummins Southwest, Inc. Cyprus Coal Company Harnischfeger Corporation Hemscheidt Corporation Jennmar Corporation Joy Technologies, Inc. K&P Sales Engineers, Inc. Kennametal, Inc. Kerr McGee Coal Corporation McLanahan Corporation National Mine Service Company The North American Coal Corporation Peabody Coal Company Pittsburg & Midway Coal Mining Co. Roberts & Schaefer Company Santa Fe Pacific Coal Corporation Southern Pacific Lines Tamarron Resort Utah Power & Light Company Utility Fuel

Jan 1, 1991

Allis Mineral Systems ARCO Coal Company Buckley Powder Co. CALCO, Inc. Coal Magazine Colowyo Coal Company Continental Conveyor & Equipment Company Crane & Hoist Sales Cummins Southwest, Inc. Energy West Mining Company Paul J. Epley FMC Corporation The Falkirk Mining Company Fleischli Oil Co., Inc. T. J. Gundlach Machine Company Halbach & Braun Harnischfeger Corporation Hemscheidt Corporation Hyatt Regency Beaver Creek Jennmar Corporation Joy Technologies, Inc. K&P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation McLanahan Corporation National Coal Association The North American Coal Corporation Northwestern Resources Company Peabody Coal Company Phillips Machine Service, Inc. Pincock, Allen & Holt, Inc. Pittsburg & Midway Coal Mining Co. Roberts & Schaefer Company Rust Tractor Company Salt River Project Santa Fe Pacific Coal Corporation Schroeder Industries Shearson-Lehman Brothers Southern Pacific Transportation Stamler Corporation Trapper Mining Inc. Wagner Equipment Company Western Energy Company Wheeler Machinery Company

Jan 1, 1992

Jan 1, 1994

Amax Coal Inc. Colowyo Coal Company Continental Conveyor & Equipment Company Crane & Hoist Sales Cummins Southwest, Inc. Energy West Mining Company Paul J. Epley The Falkirk Mining Company Fleischli Oil Company T. J. Gundlach Machine Company Halbach & Braun Hemscheidt Corporation GH Hensley Ingersoll Rand Jennmar Corporation Joy Technologies K & P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation L & H Welding McLanahan Corporation National Coal Association The North American Coal Corporation Northwestern Resources Company Peabody Western Coal Company Phillips Machine Service, Inc. Pincock, Allen & Holt The Pittsburg & Midway Coal Mining Co. Ramsey Technology, Inc. Roberts & Schaefer Co. Rust Tractor Company Salt River Project Schroeder Industries Smith, Barney, Shearson Snowmass Resort Association Southern Pacific Lines Stamler Corporation TerraMatrix TIC (The Industrial Company Wyoming, Inc.) Trapper Mining Inc. Wagner Equipment Company Western Energy Company Wheeler Machinery Company

Jan 1, 1993

The second annual RMCMI Mine Rescue Performance Evaluation was held in conjunction with the 1993 RMCMI Convention at Beaver Creek. [ ] Six teams participated in this year's evaluation; BHP Minerals, Navajo Mine, Fruitland. NM; BHP Minerals - LaPlata Mine. LaPlata, NM; BHP Minerals - San Juan Mine. Waterflow. NM; The Coteau Properties Company - Freedom Mine, Beulah. ND; Cordero Mining Company, Gillette, WY; and The Falkirk Mining Company - Falkirk Mine. Underwood, ND. The Western Energy Company of Colstrip, MT was represented through observers and evaluators. [ ] Realistic industrial related scenarios, closely simulating the stress of actual rescue incidents, were provided by members of the Eagle Valley Ambulance Service. Five different scenarios were presented to each team on the first day of the evaluation and three on the second. Each team was given the pertinent information to solve the problem as they assembled at the scenario site. The scenarios were going on simultaneously and each team was unaware of the circumstances until they entered the scene. Interested onlookers were afforded the opportunity of viewing the actual simulated rescue operations as they occurred. The teams received valuable pointers and direction from the ream of evaluators following each scenario. They were are also given the opportunity to observe the other teams in action and to meet with the members of all the teams to share information and ideas during team meetings per the predetermined schedule. The primary goal is to recognize current rescue skills, knowledge, and abilities of participating teams. In doing this, each team was provided with individual evaluations and a path for improvement as needed. Each team was recognized for their efforts at an awards breakfast on the final day of the evaluation. New innovations in rescue equipment were introduced and demonstrated for interested teams following the awards program. The importance of progressive training such as what we are witnessing at evaluations during the RMCMI conventions cannot be stressed strongly enough. These teams are the providers of immediate rescue and medical care for victims of accidents at their respective properties. Every mining operation has the potential for very serious accidents due to immense size of equipment and mining logistics. These rescue teams must be prepared to act with the most immediate, professional and knowledgeable actions to save lives and prevent further injuries. Safety is a primary concern of every mining operation and the mine site rescue team is an integral part of that safety effort. The evaluation program is very appreciative for the financial support of the following businesses to enable this program to continue: Safety Master, Acme Welding, North American Coal, Triune. Cummins, OK Tire. Modern Industrial, The Industrial Company, Mine Safety Appliances (MSA), Biomarine, Personal Safety Enterprises, Inc., and Blattner Construction, Thank you again for your much needed assistance. Plan to be a part of next year's Mine Rescue Evaluation Program as a participant or an observer. You will be amazed at the skill levels of the Rescue Teams. See you next year! Linda G. Ash The falkirk Mining Company [ ]

Jan 1, 1993

Amercable, Inc. Andalex Resources, Inc. ARCO Coal Company Behre Dolbear & Company, Inc. Colowyo Coal Co. L.P. Continental Conveyor & Equipment Company Crane & Hoist Sales Crested Butte Mountain Resort Cyprus Amax Coal Co. Energy West Mining Company The Falkirk Mining Company Fleischli Oil Co. Inc. Halbach & Braun Industries Hemscheidt Corporation GH Henley Industries Ingersoll-Rand Co. Jennmar Corporation Joy Technologies, Inc. K & P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation L & H Welding & Machine Co. McLanahan Corporation National Coal Association The North American Coal Corporation Northwestern Resources Company Peabody Western Coal Company Phillips Machine Service Pincock Allen & Holt Ramsey Technology, Inc. Rust Tractor Company Salt River Project Schroeder Industries Stamler Corporation TerraMatrix TIC (The Industrial Company Wyoming, Inc.) Trapper Mining Inc. Wagner Equipment Company Western Energy Company Wheeler Machinery Company

Jan 1, 1994