Search Documents

By E. M. Bloomfield, C. A. Jermy

Geotechnical tests were carried out within an area of the coastal sand dune cordon of northern KwaZulu-Natal which is currently being exploited through mining of heavy mineral sands. In situ and laboratory tests were carried out to assess the density, strength and stability of the dune sand material before and after mining. The most stable combination of sand (>63µm) and fines(<63µm) material was determined as well as the effects of compaction on the strength and permeability of the sand dune samples. In situ DCP and density tests showed that the sand dunes fall in density immediately after mining has taken place. However, settlement of the dunes occurs with time and the density increases within the top 2 metres, and particularly once the dunes become re-vegetated. Laboratory tests carried out showed that the dune sand with between 20% and 30% added fines had the highest shear strength and dry density, but the permeability was shown to decrease steadily with increasing fines up to 40% fines added. The addition of fines would result in steadily increasing water flow problems. Compaction of the dune sands was shown to significantly increase the density and the shear strength, but with a corresponding dramatic decrease in the permeability of the material. Slope stability analysis carried out on models of the dunes with increasing fines showed that the addition of fines increases the stability of the dune sands up to a peak of about 30% fines added, and compaction further increases the stability of the dune sands. Despite the benefits of compaction on the stability of the tailings dunes, the loss of permeability is thought to outweigh the benefits as well as the high costs involved. The stability of the tailings dunes greatly increases after re-vegetation. Compaction and densification of the tailings dunes may be necessary within the top 2 m interval if large-scale construction takes place on the sand dunes. Petrographic analysis was performed to understand the granular interactions of the sand and fines fractions, and the effect of the in situ weathering of the dune sands on the stability of the sand dunes. As the fines contents increase the gaps between the sand grains are filled, until a point where the percentage of fines begins to push the sand grains apart.

Jan 1, 2003

By R. Romano, E. Montalar, J. B. Serón

The SMR geomechanics classification system (adaptation of RMR for slopes) is reviewed with data from 87 actual slopes in Valencia. In a research project, SMR has been applied by a GIS system, as a method to forecast stability problems in future road construction. As a result of this work a methodology for GIS application has been developed. On revient sur la classification geomechanique SMR ( une adaptation du RMR pour talus et pentes) avec les dates de 87 talus existant autour de Valencia. Dans le cadre d’un projet de recherche SMR a été appliquée, avec un système GIS, comme méthode de prévision de stabilité problèmes dans la construction de futures routes. Une méthodologie pour l’application du GIS a été développe. Das Geomechanische Einteilungssystem SMR (eine Anpassung des RMR an Böschungen) wird an Hand der Daten von 87 Böschungen im Gebiet von Valencia überdacht. In einem Forschungsprojekt wurde das SMR in einem Geographischen Informationssystem (GIS) als Methode zur Vorhersage von Stabilitätsproblemen bei zukünftigen Straßenbauprojekten eingesetzt. Das Ergebnis dieser Arbeit ist die Entwicklung einer Methodologie für die GIS-Anwendung

Jan 1, 2003

By Simon Mundike, Muwindwa Lipalile

A scraper based block cave method has been successfully applied to extract the Lower Ore Body at Nchanga since the 1950?s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas; the 2420 8E 1C trial drift was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre reinforced shotcrete was extended to other drifts. This paper describes the application of fibre reinforced shotcrete at Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

By Li. S., C. Sili

Abstract. Study on nonlinear damage localization process of rocks under water chemical corrosion is a more interesting topic in rock mechanics research world widely. It is very important in estimating long term stability of rock engineering, design of nuclear waste repository and its performance estimation, geothermal and petroleum development. This paper reports that new development of study on the topic, including methodology, results of meso-mechanical test, real-time CT scan test and acoustic emission test, temporal fractal behaviors, neural dynamic modeling and chemical-induced damage law, etc. This paper also discusses the research directions of the topic in the near future. Zusammenfassung. Untersuchung zum durch die chemische Corrosion induzierten Schaedigungsprozess ist einer der Trends im Gebiet der Felsmechanik. Sie ist zugleich ein sehr wichtiges Forschungsprojekt u.a. fuer geotechnische Langzeitstabilitaetsanalyse, Langzeitsicherheit eines Endlagers, Erdwaerme- und Erdoelfoerderung. Dieser Aufsatz stellt die neusten Entwicklungen in den folgenden Teilgebieten zusammen: Untersuchungsmethoden, Laborversuchsergebnisse der Mikromechanik, der Computer-Tomographie und der akustischen Emission, zeitabhaengige Fraktaleigenschaften, Modelle fuer die Nervendynamik sowie Modelle fuer chemie-induzierte Schaedigungen. Zum Schluss werden kuenftige Forschungsschwerpunkte bzw. –richtungen diskutiert. Résumé L’étude du processus de la localisation de l’endommagement du à l’érosion chimique est un thème d’actualité pour la mécanique des roches. Elle est également un sujet de recherche d’importance dans l’évaluation de la stabilité à long terme des ouvrages rocheux, l’analyse du system de stockage des déchets nucléaires et l’évaluation de son comportement, l’exploitation de l’énergie thermique et pétrolifère, etc. Cet article présente le développement actuel dans ce domaine, incluant la méthodologie d’étude sur le processus de la localisation de l’endommagement dû à l’érosion chimique, l’analyse des essais mécaniques avec l’observation microscopique, du balayage en temps réel (CT), et de l’émission acoustique. On aborde ainsi modèle des caractéristiques fractural du temps, le modèle de la mécanique dynamique neural, ainsi que la loi de comportement d’endommagement dû à l’effet chimique. Enfin, les perspectives relatives à ces études sont présentées et discutées.

Jan 1, 2003

By A. K. Raji, E. F. Orumwense, M. O. Ojumu

The Fourth Industrial Revolution has driven significant advancements in autonomous robotic systems, particularly in subsea exploration and offshore mineral dredging. This review examines the latest developments in electrically powered quadrotor-track subsea robotic crawlers, highlighting their potential to enhance efficiency, mobility, and adaptability in challenging underwater environments. The integration of advanced automation, artificial intelligence, and real-time control systems has paved the way for more effective robotic solutions in offshore mining. This study explores the dynamic performance of hydraulic crawlers to quadrotortrack robotic dredgers, focusing on their propulsion, navigation, and stability under high hydrodynamic conditions. By leveraging state-of-the-art technologies such as lithium-ion battery power systems, intelligent microprocessors, and sensor-based control mechanisms, these robotic crawlers offer a promising alternative to conventional subsea excavation methods. Furthermore, the review analyses recent experimental and simulation-based studies that assess the feasibility and performance of these systems in real-world applications. The findings of this review provide valuable insights into the role of 4IR in transforming subsea robotics for offshore mineral dredging. By addressing existing limitations and identifying key technological advancements, this study contributes to the ongoing development of nextgeneration robotic systems capable of operating efficiently in extreme underwater conditions

Jan 30, 2026

By J. L. van Niekerk, J. Gunaselvam

This study investigates the use of appropriate seating systems for the control of whole-body vibration exposure in vehicles used in the SA mining industry. Six suspension seats were tested with six test subjects to determine the most suitable seat for an articulated dump truck based on the EM1 requirement in ISO 7096 (2000) standards. Transmissibility functions were measured in the laboratory using the newly commissioned Dynamic Seat Testing Facility with two excitation levels of 1m/s2 and 2 m/s2 r.m.s. in the 0.5 - 30 Hz frequency range. SEAT values were calculated for two input spectrums, the EM1 input spectrum specified as in ISO 7096:2000 and measured road vibration data measured on a typical articulated dump truck. The averaged SEAT value calculations indicated that not one of the seats will qualify as an ISO 7096 (2000) suspension seat but that it is possible to select a seat that will significantly reduce the vibration the driver will be exposed to.

Jan 1, 2003

The paper deals with the importance of design, and of codes of practice, in ensuring safe working conditions in mines. The design principles involved in the design process are dealt with, and the importance of a logical design process is emphasized. The links between the requirements for developing a code of practice, embodied in the existing guidelines for the preparation of such a code, and the design principles and process are considered in some detail. Finally, suggestions are included which may provide improvements to the code and hence, ultimately, lead to further improvement in safe working conditions.

Jan 1, 2003

Professor N. S. Budavari holds a Dip!. Min. Eng. from the Technical University of Sopr on, Hungary, and a Ph.D. degree from the University of Newcastle-upon-Tyne, U.K. Mr J. J. Geldenhuys, Pr. Eng., is Divisional Manager Mining of Anglovaal Limited, being in charge of Prieska Copper Mines (Pty) Limited, Loraine Gold Mines, Limited, and Village Main Reef Gold Mining Company Limited.

Jan 1, 1983

By P J. Terbrugge, O K. H Steffen

Open pit slope design has conventionally been effected as a bottom up function utilising available geotechnical information. This results in a decision criterion based on Probability of Failure and Factor of Safety with a risk assessment being carried out on the proposed design slopes. The design approach recommended reverses the process using fault event tree decision methodology. The consequences of this approach are that acceptable risk criteria have to be determined by mine owners. Slopes are then designed by the technical staff to achieve these corporate goals. Benefits that arise from the process are that the owners take a proactive decision on the risk benefit relationship allowing the technical staff to optimise the geotechnical exploration programme and design.

Jan 1, 2006

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

By Christian Heili

In 1991 the Government of the Republic of Zambia passed legislation providing for the privatisation of Zambia Consolidated Copper Mines Limited (ZCCM). The newly formed Mining Companies, established after nearly a decade of difficult and protracted negotiations on such matters as, cash at close; retained percentage interest by ZCCM; equity investment; future investment commitment and tax concessions, were faced with great internal challenges and a harsh external environment. There was a convergence of a number of negative forces that had and will continue to have an impact on the mining environment in Zambia. The most crucial of these being, the competitive pressures of the global economy, fluctuating copper price and the prevailing HIV/AIDS pandemic. In the short period after privatisation, the Industry has seen the collapse of Binani Industries (Luanshya Mine), the withdrawal of Anglo America Corporation from Konkola Copper Mines Plc and the disposal of Chambishi Cobalt and Acid Plants by Anglovaal Mining Ltd. The objective of this paper is to provide a theoretical and practically researched foundation, which may be used to assist Zambian Mining Companies in making informed decisions on the issue of Strategic Outsourcing and the degree to which this may support the successful and sustainable growth of the Zambian Copper Mining Industry. If judiciously implemented, Strategic Outsourcing has the potential to generate a practical business valuation and process to assist Mine Management in the achievement of their business goals and consequently the return on investment to their Shareholders.

Jan 1, 2005

By O. S. Tinkler, K. C. Sole

Approximately 20% of current world copper cathode output is produced using a hydrometallurgical process route, generally referred to as the leach–solvent extraction–electrowinning flowsheet. Since its commercialization in the late 1960s, steady improvements in the performance and efficiency of the solvent-extraction reagents and equipment, combined with significant developments in leaching and electrowinning, have made an ever-widening range of ore types amenable to this technology. Following successful implementation on all major continents, a large proportion of growth in recent years derives from the re-emergence of copper solvent extraction in the Central African Copperbelt. This review provides a brief history of the development and evolution of copper solvent extractants and mixer-settler contactors, and the significance of the Copperbelt region in achieving commercialization and acceptance of the technology. The opportunities and challenges presented by the abundant high-grade oxide ores of the Copperbelt are contrasted with the processing of solutions derived from the low-grade mixed oxide–sulfide ore bodies that are prevalent in other geological regions. The current status of hydrometallurgical copper production in the African Copperbelt, within a global context, and a medium-term outlook for the technology are discussed.

Jul 5, 2023

By T. C. Alex, K. M. Godiwalla, R. K. Jana

Manganese nodule, available in ocean beds, is a potential resource of the future for copper, nickel and cobalt. Recovering only these metals, containing less than 3% by weight, will result in the generation of large amount of residue. In addition to the material losses, several environmental and ecological problems arise out of this. The present study has been aimed at reducing the environmental and ecological problems associated with massive generation of this residue together with utilization of the resources. Presence of ~ 20% manganese and ~16% silicon in the residue has prompted us to check its suitability as a raw material for silicomanganese production. Lower manganese content and lower Mn/Fe ratio of the residue than that required for silicomanganese production has been corrected in this study by suitable blending. The efficacy of blending and its thermodynamic aspects using FACTSAGE software are discussed. The studies conducted indicate viability of bulk utilisation of the residue through silicomanganese production and thereby reducing the burden on environment to a great extent.

Jan 1, 2007

By J. A. Cruise

From 27th to 29th September, The South African Institute of Mining and Metallurgy held a Colloquium on Equipment Alternatives in Underground Mining in Johannesburg. The Colloquium, which was highly successful, was held concurrently with the 1988 Electra Mining Exhibition. Particle characterization The Fourth European Symposium on Particle Characterization is to be held in Nirnberg, West Germany, from 19th to 21st April, 1989.

Jan 1, 1988

ADVANCES IN EXTRACTION METALLURGY AND REFINING A symposium organised by the Institution of Mining and Metallurgy will be held in London from 4th to 6th October, 1971. Particulars can be obtained from: The Secretary, Institution of Mining and Metallurgy, 44 Portland Place, London WIN 4BR, ENGLAND. ICAMC -71 - HUNGARY The Third International Conference on Automatic Control of Mines and Collieries will be held at Balantsfured, Hungary from 27th to 30th September, 1971. Further particulars can be obtained from: ICAMC - 71, Budapest 3, P.O. Box 115, HUNGARY. AUSTRALIAN INSTITUTE OF MINING AND METALLURGY Illawarra Branch A symposium on "Blast Furnace Injection" is to be held at Wollongong University College from 15th to 17th February, 1972. About 20 papers on various aspects of blast furnace injection will be presented, including two on nonferrous furnaces. Further particulars may be obtained from: N. Standish, Chairman, Symposium Committee, Wollongong University, Australia 2600.

By G. Chisakuta, P. Bwando, G. Mitshabu

By the end of 2022, the south-eastern Copper Belt region of the Democratic Republic of Congo was host to more than 40 small, medium, and relatively large sized copper solvent extraction sites. To date, solvent extraction reagents supplied in this region have never exceeded 50% of ketoxime content. We generated laboratory extraction and strip isotherms and used these with the BASF IsocalcTM modelling software to assess the benefit of using higher ketoxime blends on the main metallurgical performance indicators such as copper recovery and net transfer. Pure ketoxime extractants combine a relatively low strip point and a decent loading capacity, which are most effective as the pH of the pregnant leach solution gets closer to 2.

Jan 1, 2023

By X. B. Zhao, J. G. Cai

When stress wave propagates through fractured rock masses, the wave will be slowed and attenuated due to the presence of these fractures. If the amplitude of stress wave is large enough to mobilize nonlinear deformation of these fractures, they will present different effects on one-dimensional P-wave propagation compared with those of linear deformational fractures. The static BB model is adopted to describe the nonlinear deformational behavior. Method of characteristics combined with displacement discontinuity theory is used to build analytical solutions of wave particle velocities and wave stresses. These equations are numerically solved with sufficient accuracy.

Jan 1, 2003

By W. Zhu

ABSTRACT: This paper presents further developments of the principle of Construction Process Mechanics of rockmasses, The principle of loading variations analyses in space-time is systematically described. To demonstrate the applicability of the theory and method, the effect of the construction process of two practical engineering cases are analysed. ZUSAMMENFASSUNG: Das Mechaniksprinzip vom Konstruktionsprozess des Massenfels wird in diesem Aufsatz weiter Entwickelt.. Das Prinzip von Variationsladungsanalyse mit dem Zeit-Raumseffekt wird systematisch erklaert. Um die Anwendungsmoeglichkeit der Theorie und der Methode zu anschaulich darstellen, das Mechanikseffekt des Konstruktionsprozess wird fuer zwei praktische Anwendungsbeispielen zergliedert. : RESUME: Dans ce papier le development se fait pour principles de la mechanique de process de construction . Le principle de variable analyse considerant effet de temps et de Space est present ´e . Pour demonstrer l´appilicabilite de le theorie et la methode , l´èffect de processe de construction pour ce deax examples sont analysés .

Jan 1, 2003

By J. Muralha

The paper presents the limit equilibrium equations for the analysis of toppling blocks on a rock slope. The safety conditions are assessed by a numeric procedure implemented in an Excel worksheet. The UDEC numerical program was exploited to validate the procedure. A probabilistic model considering the spacing variability of the discontinuities was developed to define the most relevant parameters in this kind of problems. La communication presente les equations d’équilibre limite pour l’analyse de blocs rocheux sur une pente. Les conditions de securité sont évaluées par une procédure numérique en Excel. Le logiciel UDEC a été exploité pour valider cette procedure. Un modèle probabilistique a été developpé pour définir les plus importants paramètres dans ces problèmes. Das Referat stellt die Grenzgleichgewichtsgleichungen für die Analyse von umstrürzenden Blök-ken auf eines Felshang vor. Die Sicherheitsbedingungen werden durch ein numerisches Verfahren mit Excel beurteilt. Um die Gültigkeit des Verfahrens festzustellen, wurde das Programm UDEC benutzt. Ein die Klufabstandsvariabilität berücksichtigendes probabilistisches Modell wurde entwickelt, um die wichtigsten Parameter dieser Probleme zu bestimmen.

Jan 1, 2003

By Frank Johnson

Between 2000 and 2006, platinum production from the South African mines expanded from 206 to 307 tonnes (DME, 2007). Most of this additional metal has come from traditional ?narrow? reef stoping, generally taken to mean stoping in working places with a mining height of less than 1,5 metres. It is well known that narrow-reef stoping presents safety, technological and ergonometric challenges (Pickering, 2007). In planning for the expansion, which is still continuing, the platinum mining industry realized that it could not simply continue with traditional methods of narrow-reef mining. Particular issues identified were: ? High labour-intensivity: caused by use of hand-held rock drilling machines, labour-intensive support installation and stope cleaning; ? Dependence on rock-drillers: this occupation is no longer an attractive one and there is a reducing flow of new recruits; ? Safety: most of the work is performed close to the new faces, where there is the greatest exposure to the hazards of falling rock.

Jan 1, 2008