Search Documents

By M. Mathey

The application of the Monte Carlo technique to production planning and everyday economic decisionmaking in mine production management is demonstrated. The logic is detailed using an example of underground production with continuous miners (CMs) and truck haulage. It is argued that availability of equipment and personnel are the predominant variables influencing mine output and productivity and that those availabilities may be well represented by binomial probability distributions. The probabilistic model is implemented in a standard Excel® spreadsheet with Palisade’s @Risk add-on to facilitate simulations. Starting from model calibration against data obtained from a mine’s annual reports, some general interdependencies of availability, utilization, productivity, and costs of production processes are outlined. Finally, several possible options and their consequences as regards production improvements are explored.

Dec 13, 2022

By B. Besa, S. Nalukui

Globally, the demand for mineral products is ever increasing. Extraction of these mineral resources results in the continuous production of a huge volume of waste material, including tailing dumps. The mass of tailings usually exceeds the actual resource and often contains hazardous contaminants. This study investigated the effects of tailings disposal on soil, water, and air quality in the Nampundwe area. Water, soil, and dust samples were collected from different locations in the surrounding communities. The constituents analysed in the samples included copper, cobalt, iron, sulfate, and silica. According to the results obtained, some seepages occurred from the tailings impoundment to the shallow aquifer in the area. However, the general water quality meets the Zambia Environmental Management Agency (ZEMA) statutory limits. Recorded concentrations of sulfate (1500 mg/l), copper (1.5 mg/l), cobalt (1.0 mg/l), iron (2.0 mg/l), and silica were between 0.003 mg/l and 705 mg/l, which is far below ZEMA’s statutory limit. Silica concentration was also evident in the air. The highest concentration recorded was 260 ppcc (particle per cubic centimeter) recorded in July 2019 from the northern direction of the tailings dam. The concentration was below the statutory limit of 350 ppcc. The topsoil from the northern part of the tailings recorded a silica dust concentration of 39.9 ppcc. Iron was evident in the underground soil with a concentration of 8.01 ppcc, cobalt 0.005 ppcc, copper 0.051 ppcc, while sulfate was recorded as 0.41 ppcc.

Oct 9, 2024

By L. Woollacott, R. P. King

This paper presents data collected from full-scale plants in order to verify the predictions of a new simulator of CIP or CL operations. Good agreement was found between the experimental data and the simulator predictions. The simulator is able to predict the effects of many of the complex operating phenomena in GIP and CL plants that previous simulation techniques could not describe. This is illustrated by predictions of how factors, such as the manner of carbon transfer, concurrent leaching, and gold loading on eluted carbon, can affect the performance of an adsorption plant.

Jan 1, 1990

By J. Petersen, T. Moyo, D. Maharaj

This study investigates the effect of ammonium thiosulfate on the leaching of gold from the contacts of unpopulated cut electronic printed circuit boards (PCBs). Studies in the literature show ammonium thiosulfate to be a viable option in comparison to the commonly used but hazardous cyanide leaching route. However, the simultaneous dissolution of Cu interferes with the Au leaching reaction, often limiting the extraction to moderate levels. To optimize the system, an ammoniumthiosulfate system containing 0.5M ammonia, 0.5M ammonium thiosulfate, and Cu(II) sulfate at varying concentrations was studied as an alternative hydrometallurgical option for the recovery of gold from PCB. Tests were done with unpopulated standardized model PCBs (cut to 15 x 30mm pieces). Gold extraction of 47.3% was achieved after a 24-hour leaching experiment with a 0.02M copper background concentration. Further experiments focused using different initial background Cu concentrations (0M – 0.1M) to determine its effect on both gold and copper extractions. An initial Cu concentration of 0.045M resulted in the highest gold extraction, with 93.7% extraction after 6 hours of leaching. Further analysis of the data shows that the kinetic rate of gold leaching is correlated in a first-order dependence with the actual copper concentration in the solution, which increases with the concomitant dissolution of copper and gold from the PCBs. A lower threshold of 0.017M and an upper threshold of 0.15M copper in solution were determined, in between which gold extraction shows this first-order rate increase. The upper threshold is potentially linked to the onset of copper precipitation, which blinds the metal surfaces, slowing further leaching. The findings of this study suggest that in an industrial recovery operation of gold from waste PCB using the thiosulfate method, copper concentrations need to be carefully monitored, and the process should preferably operate with uncut or coarsely cut untreated boards to minimize exposure to copper circuits.

Dec 11, 2024

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives have several potential pitfalls. These are outlined in the present paper. The main findings are as follows:•,Coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate •,For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where, ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition •,Significant errors could be made if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen) •,For elemental analyses, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range •,For representation of sulphur in coal, double-counting due to SO3 in the ash analysis should be avoided •,Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2; however, use of some of these species without considering the experimentally determined gross CV results in significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy (up to 6.9% error for a set of South African coals). Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than the abovementioned four, provided the enthalpy is corrected •,It is recommended that an ‘enthalpy correction value’ is incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to the form of carbon being different than graphite should be used, as that would imply doublecounting some effects."

Jan 1, 2014

By J. R. Dixon

Gold mining has been undertaken in South Africa for more than a century. A great proportion of that mining has been from the Witwatersrand Basin; a geological phenomenon that has few parallels throughout the world. It has produced some 47 000 tonnes of gold mainly from underground mines, many of which have been truly world class gold mines. The gold mines of the Witwatersrand Basin have dominated world gold production from their inception and their production has been one of the cornerstones of the development of South Africa as a whole. The mines have some very specific characteristics; their sheer size, the depth of extraction, the nature of the orebodies, and their labour-intensive methods. The mines have also been part of the Mining House concept-a concept unique to South Africa. South African production has declined from a maximum of 1000 tonnes in 1970 to 470 tonnes in 1997. This, as a percentage of western world production, has declined from a maximum of 79 per cent (in 1970) to 21 per cent of world production (in 1997). The nineties' have seen South Africa and its mining companies move onto the world stage and face the harsh realities of having to compete in all spheres of business with their aggressive counterparts principally in Australia, Canada and the USA. The fight is for investment funds with the owners looking for the best returns on their money. In his address Roger Dixon will examine the current situation in the gold mining industry and examine the competitiveness of the mines of the Witwatersrand Basin compared with their peers worldwide. He will also discuss some of the fundamental challenges facing South African gold mines in the areas of legislation, technology, industrial relations, and health and safety. The environment in which the mines operate has changed radically in recent years and their ability to respond to these challenges will determine their future existence.

Jan 1, 1998

By R. W. O. Kersten

The main objective of The South African Institute of Mining and Metalurgy is to identify the needs of the mineral and metals sector of the South African economy, and to initiate the means by which the requirements for technology and scientific knowledge can be satisfied. To achieve this, the Institute organizes schools to promote technology transfer and to satisfy the needs of its members for continuing education by the exchange of technical information, the communication of ideas, and the identification of technological problem areas.

Jan 1, 1986

By N. Snyders, I. Mwandawande, S. M. Bradshaw, M. Karimi

"Flotation columns are normally operated at optimal superficial gas velocities to maintain bubbly flow conditions. However, with increasing superficial gas velocity, loss of bubbly flow may occur with adverse effects on column performance. It is therefore important to identify the maximum superficial gas velocity above which loss of bubbly flow occurs. The maximum superficial gas velocity is usually obtained from a gas holdup versus superficial gas velocity plot in which the linear portion of the graph represents bubbly flow while deviation from the linear relationship indicates a change from the bubbly flow to the churn-turbulent regime. However, this method is difficult to use when the transition from bubbly flow to churn-turbulent flow is gradual, as happens in the presence of frothers. We present two alternative methods in which the flow regime in the column is distinguished by means of radial gas holdup profiles and gas holdup versus time graphs obtained from CFD simulations. Bubbly flow was characterized by saddle-shaped profiles with three distinct peaks, or saddle-shaped profiles with two near-wall peaks and a central minimum, or flat profiles with intermediate features between saddle and parabolic gas holdup profiles. The transition regime was gradual and characterized by flat to parabolic gas holdup profiles that become steeper with increasing superficial gas velocity. The churn-turbulent flow was distinguished by steep parabolic radial gas holdup profiles. Gas holdup versus time graphs were also used to define flow regimes with a constant gas holdup indicating bubbly flow, while wide gas holdup variations indicate churn-turbulent flow. IntroductionTwo types of flow can be distinguished in gasliquid flows in bubble columns: bubbly flow and churn-turbulent flow. The bubbly flow regime is characterized by uniform flow of bubbles of uniform size. Churn-turbulent flow, on the other hand, is characterized by a wide variation in bubble sizes with large bubbles rising rapidly and causing liquid circulation.Flotation columns are normally operated in the bubbly flow regime, which is the optimal condition for column flotation (Finch and Dobby, 1990; Yianatos and Finch, 1990; Ityokumbul, 1992). However, it has been generally observed that flotation column performance deteriorates when the superficial gas velocity is increased beyond a certain limit where the flow regime changes from bubbly flow to churn-turbulent flow (Xu, Finch, and Uribe-Salas, 1991). The identification of this critical or maximum superficial gas velocity is therefore important for optimal operation of flotation columns."

Feb 1, 2019

By D. F. Malan, D. Ile

This study explores the use of backfill in hard rock bord-and-pillar mines to increase the pillar strength and extraction ratio at depth. The use of backfill will also minimize the requirement for tailings storage on surface and the risk of environmental damage. A literature survey indicated that backfill is extensively used in coal mines, but rarely in hard rock bord-and-pillar mines. To simulate the effect of backfill confinement on pillar strength, an extension of the limit equilibrium model is proposed. Numerical modelling of an actual platinum mine layout is used to illustrate the beneficial effect of backfill on pillar stability at greater depths. The magnitude of confinement exerted by the backfill on the pillar sidewalls is unknown, however, and this needs to be quantified using experimental backfill mining sections equipped with suitable instrumentation.

May 3, 2023

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C.1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By S. Swanepoel, A. V. Cherkaev, Q. G. Reynolds, M. Erwee

Ferrochrome (FeCr) is a vital ingredient in stainless steel production and is commonly produced by smelting chromite ores in submerged arc furnaces. Silicon (Si) is a componrnt of the FeCr alloy from the smelting process. Being both a contaminant and an indicator of the state of the process, its content needs to be kept within a narrow range. The complex chemistry of the smelting process and interactions between various factors make Si prediction by fundamental models infeasible. A data-driven approach offers an alternative by formulating the model based on historical data. This paper presents a systematic development of a data-driven model for predicting Si content. The model includes dimensionality reduction, regularized linear regression, and a boosting method to reduce the variability of the linear model residuals. It shows a good performance on testing data (R2 = 0.63). The most significant predictors, as determined by linear model analysis and permutation testing, are previous Si content, carbon and titanium in the alloy, calcium oxide in the slag, resistance between electrodes, and electrode slips. Further analysis using thermodynamic data and models, links these predictors to electrode control and slag chemistry. This analysis lays the foundation for implementing Si content control on a ferrochrome smelter.

Mar 14, 2024

A brief overview is given of the issues regarding the processing of waste electrical and electronic equipment (WEEE). The printed circuit board component of WEEE is an exceptionally complex feed to possible recycling processes. Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy. Iron and aluminium were found not to be part of the alloy. The alloy was characterized by SEM-EDS, and three phases were identified: alpha and delta bronzes, and a lead-rich phase. Calculations show that about 56 mass per cent of the alloy is the alpha phase, 35 per cent delta phase and 9 per cent lead phase. A simplified approach using appropriate binary phase diagrams was used to derive a phase composition for the alloy. This was further backed by FactSage calculations, which showed that the simplified approach was appropriate for this alloy. The experimental findings and theory were found to agree well.

Jan 1, 2009

By E. Keskinkilic

Drying, calcination, prereduction, and smelting are the main steps in conventional crude ferronickel production. Industrially, these steps are conducted using the rotary kiln-electric arc furnace (RKEF) process. In this paper, calcination characteristics of Sivrihisar laterite ores from the Central Anatolia region are investigated. The extent of elimination of chemically bound water and other volatiles was studied by experiments conducted at various temperatures in the 250?800°C range. Phase changes were examined using X-ray diffractometry. For the particle size used in the study, 300°C was determined to be almost sufficient for complete transformation of goethite to haematite, and 700°C was required for effective elimination of all volatiles in the ore.

Jan 1, 2012

Sampling In The Coal Industry Exploration, Mine, Met and Environmental Sampling EMMES 2005 3, 4 November 2005

Jan 1, 2005

By E. Lwamba

The aim of this study was to examine the effect of grain size distribution control of the raw material mixture on the permeability of the green sinter bed and the properties of the produced sinter. This was achieved by evaluating the granulation characteristics of the sinter mixture (moisture content, granulation time and mean granule diameter) in terms of its green bed permeability, and evaluating the productivity of the sinter bed, the coke rate, tumble index (TI), abrasion index (AI), reduction disintegration index(RDI) and reducibility (RI) of the produced sinter. The raw sinter mixtures contained combinations of Thabazimbi iron ore, Sishen iron ore, coke, lime and return fines. The grain size distributions were controlled by removing the ?0.5 mm size fractions of the return fines and coke, and the ?1 mm size fraction of lime. Of the examined mixtures, a mixture of 20 mass% Thabazimbi iron ore, 80 mass% Sishen iron ore and fluxes where the coke, lime and return fines were all sized had the highest granulation effectiveness and permeability. The sintering properties of the mixtures in which the grain size distributions were controlled, were very similar for all the mixtures, but superior to the base case mixture in which the grain size distribution was not controlled. Keywords: Thabazimbi iron ore; Sishen iron ore; granulation, permeability, grain size distribution; sinter.

Jan 1, 2008

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

By Matthew D. Viergutz

MECS? HRS technology has reliably recovered intermediate pressure steam from sulphuric acid plants for more than 20 years. This steam can either generate electricity or replace steam produced by an existing fuel-fired boiler. As worldwide greenhouse gas emissions continue to rise, industries are looking for novel and cost effective solutions to reduce pollution, particularly carbon dioxide, from their plants. Waste heat recovery technologies such as HRS offer new and existing plants the opportunity to maximize energy efficiency while reducing their reliance on energy supply from external sources. This paper offers a unique look at energy recovery in sulphuric acid plants and how recent innovations in MECS? Heat Recovery System technology make HRS more financially viable ? and more green - than ever.

Jan 1, 2009

The kinetics of cyanide loss were found to be first order under any given set of conditions, allowing rate constants to be easily determined. At room temperature and in the absence of activated carbon, some cyanide is lost by hydrolysis to hydrogen cyanide, but this does not occur to any significant extent at pH values higher than about 10. A higher rate of hydrolysis occurs when air agitation is used. When activated carbon is present, an additional carbon-catalysed oxidation reaction is responsible for a fairly high loss of cyanide. The evidence indicates a reaction mechanism that consumes oxygen and produces cyanate ion. Some of the cyanate thus produced decomposes to form a mixture of ammonia, carbonate, and urea, depending on the solution conditions. Additional cyanide is lost as a result of the adsorption of sodium cyanide by the activated carbon. At high temperatures, an additional hydrolysis reaction, which involves the formation of ammonium formate as an intermediate, occurs an/j is responsible for. a high loss of cyanide, leading ultimately to the formation of ammonia, hydrogen, and carbon dioxide. The presence of activated carbon has no effect on the rate of this reaction.

Jan 1, 1990

By L. von Ketelhodt

During the period October 2003 to June 2004, a containerized optical sorting pilot plant was operated at Kloof Gold Mine on a waste rock dump. In this paper, we describe the test work and its results leading to the decision to operate this pilot plant. This paper presents the operational data and financial figures achieved during this project, in particular, for the month of June 2004 when the plant was run at full capacity on three shifts, 24 hour operation. These results are also extrapolated and presented to show the profitability of such an operation at today?s gold price levels and cost structure.

Jan 1, 2009

By J. D. Swanepoel, S. Horn, C. J. Badenhorst

Diesel particulate matter (DPM) is the particulate component of diesel exhaust, which includes diesel soot and aerosols. When released into the atmosphere, DPM can take the form of individual particles or chain aggregates, with most in the invisible sub-micrometer range of 100 nanometres. The main particulate fraction of diesel exhaust consists of fine particles and because of their small size, inhaled particles may easily penetrate deep into the lungs. The rough surfaces of these particles make it easy for them to bind with other toxins in the environment, thus increasing the hazards of particle inhalation. DPM is a significant health hazard in underground mining operations, where the use of dieselpowered equipment in confined spaces can lead to high levels of exposure among people working in these environments. Classified as a carcinogen by the International Agency for Research on Cancer (IARC), DPM has been linked to severe health effects, including respiratory and cardiovascular diseases, as well as an increased risk of lung cancer. Effective management of DPM is essential not only for protecting people’s health but also for ensuring regulatory compliance, maintaining operational efficiency, and safeguarding the long-term viability of mining companies.

Mar 5, 2025