Search Documents

By S. Banisi, S. Zare, M. Mahmoudi, M. Maleki-Moghaddam, M. Yahyaei

As the orebodies become more complex and lower grade, there is an increasing demand from crushing circuits for a finer product. When the product from a crushing circuit does not satisfy the requirements of the downstream processes, the cost of production increases. Thus, enhancing the performance of cone crushers through optimisation of their operating factors becomes important. One of the key factors affecting performance of cone crushers is the filling of the crushing chamber during the operation. The effect of varying the filling of the crushing chamber of a cone crusher was investigated. To assess the crusher performance, parameters such as crusher capacity, power utilisation, and reduction ratio were used. Extensive plant trials were conducted to obtain samples and operational data when the crusher chamber was 50% full (half-full) and 100% full, which is 300 mm above the top of the crusher chamber (super-choked condition). The results indicated a 62% difference in the crushing capacity when the crusher was operated in a super-choked condition compared to the half-full chamber level. In the super-choked condition, the size-specific energy at 12.7 mm was 20 % lower than that of the half-full condition. The Bond ball mill work index (BBWI) of crusher product indicated that the BBWI of the product of the super choked condition is 5.6% less than that of the product of half-full condition. This can be attributed to the generation of micro cracks in particles due to increase in the interparticle breakage when the crusher was operated in the super-choked mode. Keywords: Cone crushers, crushing efficiency, crushing chamber filling

Jan 1, 2020

By M. J. Deats

INTRODUCTION To prepare the reader adequately, reference should be made to the paper 'The Pioneering of Fully Mechanized Longwall Coal Mining in South Africa' by R. T. Naude and M. J. Deats, published in the February, 1967, edition of the Journal. At the time mechanized longwalling had been proved operationally feasible with encouraging results since its inception in South Africa in mid 1965. Subsequently, further top seam panels were successfully extracted with improved productivity and with some modification to equipment. In 1968, after an overseas visit by mine officials, equipment specific to suit local conditions was acquired and lower seam trials commenced. Despite initial obstacles and difficulties the first panel was successfully mined. Modification and improvements to equipment and techniques resulted in the second lower seam panel being extracted economically during 1969-1970 and with productivity exceeding even that of top seam faces. During extraction of the second lower seam panel, gradual and complete surface subsidence occurred over the panel without affecting face operations. Rock mechanics investigations had originally indicated some uncertainty regarding adverse dolerite sill behaviour which could have caused longwall mining to be hazardous. All such doubts have now been removed. RESUMÉ AS AT FEBRUARY, 1967 Mechanized longwalling was introduced in 1965 on an experimental basis in an effort to improve productivity in the newer area of the mine and to increase the quality of the comparatively dirty run of mine feed to the washing plant. In addition advantages could be predicted in the long term by better utilizing reserves of straight coking coal and increasing the life of the mine. The top seam unit was obtained on a rental basis and by the beginning of 1967, two panels, the first having a face length of 215 m, a panel length of 345 m, seam section of 1 219 mm, and the second the same face length, a panel length of 453 m and a seam section of 1 067 mm had been successfully longwalled. At this stage a best month of 24 602 metric tons with an average of 17 364 metric tons per full working month could be reported. Results were sufficiently encouraging for the company to exercise its right to acquire the equipment as its own asset and from 1967 onward, the unit has operated on this basis. From the point of view of rock mechanics, the dolerite sill over the first two panels was known to have 'bridged', only the material below the base of the sill having truly 'goafed'. No adverse pressure effects had significantly affected face operations except for two 'bumps' towards the end of operations in each panel. Gate road maintenance presented no problem. The strong inflows of water experienced on the first face were now known to be associated with an isolated water bearing fault plane and were not experienced on the second face. TOP SEAM EXPERIENCE - MAY, 1966, TO DATE Panel 2 (February, 1966, to November, 1966) The operations in panel 2 (see Fig. 1 for location of panels) continued uneventfully until the final month in this panel. At this stage, the chocks behaved most inconsistently often lowering under the weight of the canopies alone. Roof trouble became so severe that the unit was unable to produce adequately and blasting of chocks became a daily occurrence. Finally 24 m short of the planned limit it was decided that a complete overhaul was the only solution and the extraction operations commenced. At this time, the only fatal accident associated with longwalling occurred when a Non-White inadvertently fell into the panzer conveyor transfer point at the main gate. Some gate road difficulties in this panel were overcome by bolting tapes to the roof as decking and allowing them to pass over the gate chocks and collapse into the goaf. Two cribbed roof falls were also negotiated by the gate chocks at the face ends without undue difficulties. It was decided in the light of maintenance problems encountered on this face that the best solution would be to appoint a foreman solely in charge of face maintenance crews. This step has to a large extent contributed to success achieved subsequently. Panel 2-face length 213 m panel length 456 m cutting height 1 092 mm average monthly output 16 443 t best month 19 130 t Panel 3 (December, 1966, to June, 1967) By the end of 1966 results were sufficiently encouraging for the company to exercise its right to acquire the equipment. This was negotiated and the unit has operated as such to the present date. Prior to installation in panel 3, all face equipment was thoroughly overhauled underground and the chocks boost-tested to yield-load. The costs of overhauling, including almost complete hose replacement, were much higher than anticipated. Advice had been received that complete hose replacement was common practice after +/- 18 months' operation. Shortly after commencement of operations in panel 3 the chocks again failed as they had towards the end of panel 2. At this stage, the suppliers advised that the valve gear should have been repaired during the overhaul as the needle and seat seals could no longer be relied upon. This operation was impossible to carry out on the face and would have been e1ttremely time consuming. Fortunately a new type of valve gear was then available from the suppliers, termed the capsule-type valve, and a complete change over could be made on the face. The encapsulated valve has a delrin pad sealing over a raised

By L. Pretorius, S. Uludağ

This paper explores how to apply system dynamics principles to surface mining problems towards understanding the consequences of mining efficiencies. Some simulation examples related to machine and people performance have been used to demonstrate systems engineering concepts to mining engineers. The simulation tool used is Vensim, which is widely used in industrial engineering applicable to systems thinking, and systems dynamics. The science and mathematics behind the system dynamics as well as benefits and typical challenges are discussed to explore the applicability to mining problems. The benefit of having one less drill is easily quantifiable with the developed model which is one of many other measurable benefits, using the developed model. Some of the benefits of the improved quality of drill holes are not fully quantified as this depends on the mine specific inputs. There are examples of quantifying this in the other industries using system dynamics tools.

Sep 1, 2021

By C. C. Pretorius, S. Ramjee, R. J. Mostert

The study investigates the effect of prior corrosive exposure on crack growth resistance behaviour of thin sheet (3 mm thick) aluminium alloy 2024-T3 at slow strain rates. Compact tension specimens were exposed to standard corrosive environments that simulate accelerated atmospheric corrosion attack. Two corrosive environments were considered – an exfoliation corrosion (EXCO) solution and a 3.5 wt% sodium chloride solution. The unloading compliance R-curves of the two-hour EXCO-exposed specimens revealed a significant degradation of approximately 11% in the crack growth resistance behaviour (Kc_e values) compared to the baseline (air-exposed) values. Furthermore, secondary intergranular crack formation was also revealed in the plastic zone ahead of, and adjacent to, the crack tip of these specimens; which formed during the crack growth resistance loading. It is postulated that the observed degradation of the Kc_e values of the EXCO-exposed material is due to hydrogen embrittlement since the exposure times for the EXCO evaluation were limited to ensure that uniform corrosion dominated; that is, significant penetration of corrosion damage and pitting due to localized corrosive attack did not occur. The sodium chloride-exposed specimens revealed a similar degradation (13%) after 24 hours exposure. However, slight intergranular corrosive attack and isolated pitting were observed on the exposed surfaces prior to crack growth resistance loading, resulting in notch effects that could assist in crack growth. Pitting and intergranular corrosion were, however, not observed at the pre-crack tip. The relative contributions of the notch effects and the hydrogen embrittlement during the degradation of the KR performance are, therefore, unclear.

Apr 1, 2021

By M. S. Shishvan, J. R. van Duijvenbode, L. M. Cloete, M. W. N. Buxton

Geochemical and mineralogical datasets from Tropicana Gold Mine, Australia, have been used to define ore fingerprints. VNIR/SWIR spectral data were represented by four normalised wavelength regions and were clustered to form spectral classes. Sequentially, these spectral class proportions within a block and collocated XRF data were clustered to form material types (fingerprints). The material types were related to an Equotip-BWi correlation. These correlations can be used to extrapolate a hardness signature and generate a BWi proxy for different blocks. The combined fingerprints and BWi proxy can assist as a tool for enhancing the prediction of comminution behaviour. They can explain specific domain-related hardness variations. For example, one material type could be separated into a softer (~15-18 kWh/t), and harder (>20 kWh/t) material blend. This was accomplished using the commonly overlooked VNIR region at 605 nm. This outcome has significance for blending strategies.

Sep 1, 2021

By J. Saunders, N. Pretorius, G. Krafft, T. P. Katakwa

Imagine being able to see all the future planned mining activities in real time. This is exactly what SIMS (Short Interval Management System) will enable you to do. SIMS is a real time short interval control system that continuously measures and sets optimised plans for mining production processes. The system utilises algorithm-based software that takes resources (people, equipment, tasks, and workplaces) and gives you the best achievable plan. The algorithm was developed using methods found in the field of metaheuristics. A metaheuristic is a strategy to designed to efficiently search for optimal or near optimal solutions to problems that are very complex computationally. (Glover, 1986) There are several algorithms that have been developed to solve optimisation problems which are difficult to solve using traditional techniques. This has given rise to a field called evolutionary computing. (Simon, 2013) Examples of these techniques are genetic algorithms, particle swarm optimisation, and ant colony optimisation. These methods are used to solve problems in a variety of fields. As an example, Kok and Lane (2012) used particle swarm optimisation for equipment allocation in a mechanised underground mining environment. The first SIMS deployment took place in a platinum underground tabular mechanised mine near Burgersfort (province?) from 2017-2019. This included the development from a paper-based system to a fully operational online system. SIMS then moved to a second site and is currently being tested in a second platinum underground tabular mechanised mine in South Africa. Full deployment of the system is currently being phased in. SIMS was built in response to issues that have been plaguing the mining industry for years. These issues are all aligned into one major problem statement: how can we optimise mining production processes without compromising safety? This product was developed by combining years of mining experience with software development. SIMS is based on a four-pillar concept. Safety, productivity, accountability, and business improvement. SIMS uses a set of pre-configured mining and production rules, and with the resources that are available, to determine valid short term production plans. A background algorithm then determines the optimum plan to be executed. The system continuously produces a set of job cards that are pushed to respective operators on their allocated tablets. The management portal component allows you to view and manage all current and planned work on any connected device available. This allows real time visibility of completed, current, and planned work to operators, service departments and management, i.e., seeing into the future.

Sep 1, 2021

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

"Chairman: Professor B. W. MacKenzieRapporteur: Professor D. A. PretoriusPapers:Optimum spacing for soil sample traverses by W. A. HodgsonEvaluation of geochemical data by C. J. LenzResearch in oil exploration decision-making by J. W. Harbaugh and A. Prelat A drill hole data bank by M. R. AndertonOre reserve estimation and depletion planning for a beach diamond deposit by M. M. OosterveldIn opening the session, the Chairman indicated that the papers and discussions would revolve about quantitative methods of analysis and optimization of various aspects of exploration planning. The five papers would cover a wide range of topics within a general theme of exploration analysis, and it would be appropriate, therefore, to present the. papers as representing a sequential information-gathering process, namely, (i)geochemical and geophysical types of surveying for the location and identification of anomalous zones, (ii) tren¬ching and drilling of the anomalous zones found, and (iii) further refinement of the data for ore reserve calculations and production planning.The first paper, which was presented by Dr W. A. Hodgson, dealt with the optimum spacing between soil sample traverses conducted during geochemical prospecting. The theme of the paper was that the critical sampling interval should be based on the concept of element continuity, and that this interval could be determined by means of a correlogram. Ensuing discussion concerned the probability of the method, designed for areas where dispersion was high, working in localities where dispersion was either low or virtually non-existent. In the latter eases, specific orientation surveys for varying topographic, climatic and geological conditions would possibly be more useful than the preparation of correlograms. A further suggestion was made that cost versus risk should be taken into consideration when deciding upon the spacing between traverses. A balance could be struck by mathematical optimization. If the exploration budget was fixed, then the variance of risk could be minimized.The second paper was a short contribution by Mr C. J. Lenz. Computer-based plotting and evaluation of geochemical prospecting results were carried out because the low cost of analysis in Rhodesia permitted very large volumes of data to be accumulated in mass-coverage operations. Anomalous areas were demarcated within different environments by selecting probability or population boundary values from frequency distributions. In the short discussion which took place it was debated whether the method should be used only in the early high-risk stages of geochemical exploration and whether the introduction of geological bias could influence the actual results of an exploration program."

Jan 1, 2014

By R. Koen, H. Visser, A. Roodt

"SynopsisThe tetraethylammonium salt of the mono-anionic coordination compound mer-oxidotrichlorido(thenoyltrifluoroacetylacetonato- K2O,O’)niobate(V) (NEt4)[NbOCl3](ttfa)], has been prepared under aerobic conditions and characterized by single-crystal X-ray diffraction. (NEt4)[NbOCl3](ttfa)] crystallized in the monoclinic P21/c space group, with a = 11.483 (5), b = 12.563 (5), c = 17.110(5) Å, and ß = 100.838 (5)o. The complex structure exists in a 50.0% (NbA) : 50.0% (NbB) positional disorder ratio.IntroductionComplexes containing organometallic type ß- diketone ligands with O,O and O,N donor atoms are used widely in coordination chemistry and have applications in catalysis, radiopharmaceuticals, etc. (Schutte et al., 2011; Roodt, Visser and Brink, 2011; Brink et al., 2010; Otto et al., 1998). These ligand systems are very useful because of their highly coordinative nature, high solubility, and also due to their ability to be functionalized with various substituents on the carbonyl carbon atoms (Schutte et al., 2011).Only a small number of ß-diketonate ligands have successfully been coordinated to a Nb(V) metal centre, with only a select few being characterized by X-ray crystallography (Viljoen, 2009; Bullen, Mason and Pauling, 1965; Preuss, Lamding and Mueller-Becker, 1994; Funk, 1934; Davies, Leedlam and Jones, 1999; Allen, 2002. The synthesis and crystal structure determination at room temperature of mer-oxidotrichlorido (thenoyltrifluoroacetylacetonato- k2O,O’)niobate(V) {(NEt4)[NbOCl3(ttfa)]} was first reported by Daran et al. in 1979. Accordingly, for this current investigation, (NEt4)[NbOCl3(ttfa)] was re-evaluated at 100 K to determine if the structural features might change with temperature."

Jan 1, 2015

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

By D. J. Bosman

The impoved densification of sludge from neutralized acid mine drainage. by D. J. BOSMAN, B.Sc., (Member) The paper describes an investigation aimed at finding a solution to the accumulation of acid mine drainage in the old workings at Coronation Collieries, Kromdraai. The problem involved the neutralization of the acid in the water, without the large volumes of sludge and the large amounts of dissolved solids that usually result from neutralization. Pilot-plant work on the site using a limeneutralization process developed at Bethlehem Steel Corporation (U.S.A.) showed this to be a feasible method. A sludge of 22 per cent density was obtained under optimum operating parameters. The amount of suspended solids in the overflow water was very high, but this does not give rise to concern because the full-scale plant at Kromdraai will practise secondary sedimentation by running the thickener overflow through large dams with a theoretical retention time of 25 days. An analysis of the theory underlying the process is also made.

Jan 4, 1974

By D. Brazier, W. Laing, D. Nixon

Keywords: Pyrometallurgy, furnace, smelter, copper, Palabora The Palabora copper smelter has operated for the past 38 years, treating concentrates produced at the mine site. Palabora has reduced captive material by almost 40 per cent with the transition from a large open-cast to a smaller underground mine. The smelter and refinery complex was designed to treat 120 kt contained copper units per annum, with the underground only supplying 70 per cent of the feed. The agreed strategy was to import enough concentrates to maximise production and reduce operational unit costs. This transition has presented the Palabora management with new challenges both in technical and financial aspects.

Jan 1, 2006

By A. C. Scott

A detailed fundamental model of a zinc electrowinning cell has been developed and validated for both steady state and dynamic simulations. This model was used to investigate the effects of a range of operating variables and to find their optimum values. As well as providing useful design information for a planned upgrading of the EZ refinery, more generally it demonstrates the potential benefits to the minerals industry of the applications of modern CAD flowsheeting techniques. The SPEEDUP equation oriented CAD package was found most suitable for this task as the user can easily generate models specific to his site with any number of components and mixture properties.

Jan 1, 1987

By A. Mehmet

The feasibility of employing a multi-stage column for the recovery of gold from cyanided pulps using extruded carbon was investigated on a pilot-plant scale. It was anticipated that the column contactor would have certain advantages over conventional carbon-in-pulp plants. The feed pulp was screened to remove particles larger than 200 µm and was diluted to a solids concentration of about 23 per cent. The column was operated continuously for 24 days at a pulp flowrate of about 60 l/min and a carbon flowrate of 44 litres per day. The average gold concentrations in the barren pulp 12 hours and 24 hours after the carbon transfer were 0,012 and 0,031 mg/l respectively. The average gold concentration in the solution phase in the feed was about 2,0 mg/L. The average gold Loading on the carbon was 6290 g/t. Calcium carbonate was removed from the loaded carbon by treatment with 0,5 bed volumes of 2,8 per cent hydrochloric acid solution at ambient temperature. The calcium concentration was reduced from about 17 000 to about 500 g/t The carbon was eluted by the Zadra procedure at atmospheric pressure. The results of the elution were highly satisfactory, the gold concentration being reduced from about 6000 to about 20 g/t in 48 hours. The eluted carbon was regenerated in a Rintoul kiln at about 700°C. The activity of the regenerated carbon was found to be at least as high as that of fresh carbon.

Jan 1, 1992

By D. Harbottle, D. Rhodes, T. F. Jones, S. R. Biggs

Multiphase process design and optimization often depends upon the rheological properties of sludges and slurries. In practice the task of determining these important properties is usually carried out by removing small samples from a process line or process unit and performing tests with proprietary bench-top analysers near to site or at a remote laboratory. Sampling will remain an important procedure in industrial processes, but there is also a strong case for augmenting the routine information obtained using an in situ sensor, as suggested below. ?Sampling protocols can result in extensive turnaround periods from sample collection to the generation of results. The delay can have an effect on a variety of factors such as product quality, process operability and efficiency. ?Sampling of toxic or radioactive material can prove an even greater challenge to minimize human involvement. ?Removal often changes the rheology of a specimen, and might lead to incorrect conclusions being drawn about the condition of a sludge. ?Sludge and slurry in a containment suffers a gravitational gradient, so that a removed sample should be paired with its location, particularly in the vertical dimension.

Jan 1, 2007

By M. A. Ford

This paper reviews the history, sources, mineralogy, extraction metallurgy, conversion, and enrichment of uranium in South Africa. Over the past 40 years extraction plants were built at 27 sites, an9.over 140 kt of uranium have been produced. Older plants have had to adapt to changing market conditions, no single technology has had the opportunity to become entrenched, and costs have been reduced to a third of those of the original flowsheet. The research efforts aimed at developing the country s nuclear raw materials have been particularly rewarding, as they have enabled South Africa to become a world leader in the extraction of uranium from low-grade ores and to develop methods for uranium enrichment and the production of nuclear fuels.

Jan 1, 1993

By J. B. A. Solar Menéndez, M. A. Martínez Fidalgo, L. A. Alvarez-Santullano

1. ANTECEDENTS This present communication refers to the results of the research project entitled "Training in the correct use of chemical oxygen self rescue apparatus and also an analysis of apparatus autonomy", carried out under the auspices of the Specific Collaboration Agreement signed between the Industry Council of the Principality of Asturias (Spain) and INSALUD (National Silicosis Institute, Spain). The antecedents of this project lie in work undertaken by the National Silicosis Institute aimed at optimising efficiency in the use of chemical oxygen self rescuers through improvements in worker training. To be precise, by means of Agreements drawn up between the above-mentioned parties, a simulator was designed and incorporated as the basis of a training station within the " Fundación Barredo" of the Industry Council of the Principality of Asturias. This has been operative since the year 2001 and, up to the present, 2300 Asturian coal mine workers have been trained there. What prompted this activity was the observation of various errors in the use of the self rescuers, deriving from their innate characteristics, especially with respect to the sensation of discomfort - the high temperature and humidity of the breathed oxygen, resistance and inconvenience - and limited autonomy. It was precisely this insight that, in critical situations, lack of familiarity with the conditions of discomfort likely to be experienced during the evacuation process might lead to rejection of the equipment, with fatal consequences, that has justified the setting up of this training and simulation centre. The centre is able to provide all mine workers with the necessary training, and experience of the characteristic sensations experienced when using such equipment (Fig.. 1).

Jan 1, 2003

By B. Jack, A. Vervoort

During pillar extraction, sidewall fracturing and spalling at some collieries constitute a severe stratacontrol problem. In order to obtain a better understanding of this phenomenon, a survey of pillar corner conditions before and during pillar extraction was conducted at one particular site. For the various successive mining steps, the vertical stresses on the pillar corners were calculated by use of a three-dimensional boundary element program. A significant correlation was found between the calculated vertical stress prior to the extraction of the panel and the sidewall conditions. During the extraction of the panel, a significant deterioration of the sidewall conditions at a pillar occurred only when the adjacent pillar was mined, causing an increase in vertical stress on the remaining pillar.

Jan 1, 1992

"Sampling error and bias, especially the Increment Preparation Error (IPE), are introduced when the tool allocated to do the job fails to extract a representative sample. This is the case with chip sampling; the tool can only extract haphazard shapes of loose or fractured material and not always from within the demarcated sample area. Increment Extraction Error (IEE) and Increment Delimitation Error (IDE) could be severe, but are found to be relatively unbiased. The uncontrolled action of the sampler in discarding excess sample material after sample collection has a significant impact on the error and bias introduced with each and every extraction. A new type of bias, referred to as the ‘waste discard bias’, arises when samplers select what portion of the excess sample material to discard at the sample site. Material visually identified as waste is discarded in preference to mineralized broken ore if there is an excess of sample material. This results in a considerable error in the analytical results. The bias is proportional to the reef-waste ratio in the demarcated sample. IntroductionTwo types of ‘sampling’ are distinguished, namely sampling of particulate materials (broken ores) and sampling of solid, unbroken in situ mineralized reef. This study considers only chip- or face-sampling of in situ, goldbearing, carbon-rich conglomerates typical of the Upper Witwatersrand Supergroup and examines where components of sampling error and bias, clearly specified in the Theory of Sampling, may arise during the practice of ‘face sampling’. Many millions of face samples have been extracted from Witwatersrand-type mines using a hammer and chisel, and detailed descriptions (standard operating procedures) of how the samples should be taken have been developed by many mining companies. There is, however, no taxonomy or nomenclature for managing or reporting the different types of errors associated with chip sampling. The Theory of Sampling compiled by Pierre Gy in the early 1950s provides, comprehensive nomenclature of sampling errors that is applied to particulate sampling of ore in a lot, a stockpile, or a moving stream on a conveyor belt. The taxonomy and characteristics of sampling errors, grouped according to the sources from which they arise, and identified by Gy (1973, 1979, 1982, 1992, 1995, and 1998) are shown in Figure 1. This classification of errors is used extensively in regard to the sampling of particulate materials in the mining and minerals industry, but not in regard to chip sampling. A relatively small mass (hundreds of grams) of representative particulate material for estimating the average grade of a much larger mass (thousands of tons – the ‘lot’ in the Theory of Sampling) is extracted by the chipping or cutting of a representative rock ‘sample’ from the stope face."

Jan 1, 2016

By B. E. Protheroe, C. Allen, A. Ball

The results of laboratory abrasive and abrasive-corrosive tests carried out on a range of carbon, Iowalloy, and stainless steels are compared with underground tests conducted on similar materials on prototype shaker conveyors carrying gold-bearing quartzitic rock. The dry-abrasion resistance of all the steels was found to be better than that of mild steel. When the added effect of corrosion was tested, the stainless steels proved to be much superior to proprietary abrasion-resistant alloys both in the laboratory and underground. The ferritic stainless grades were shown to be superior on the basis of cost per unit of volume lost. This investigation has shown that laboratory tests on materials can provide valuable information on their possible performance in situ, and can thus be used to replace lengthy experiments on site.

Jan 1, 1981