Search Documents

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

This symposium, being held at The President Hotel, Johannesburg on 9th-11th September, 1969, is being jointly sponsored by The South African Institute of Mining and Metallurgy, The South African Corrosion Council and the Southern Africa Stainless Steel Development Association, and supported by the C.S.I.R. The three days of technical sessions, at which 350 delegates are expected, will include introductory films on the properties and uses of stainless steels, papers on corrosion problems and prevention, design and economics, welding and applications in industries of particular importance to South Africa. The programme includes four overseas guest speakers who are acknowledged leaders in their respective fields. Detailed programmes together with application forms for registration will be published shortly. Enquiries to P.G. Box 8954, Johannesburg.

By M. J. Deats

Your article on page 202 of the August 1993 Journal refers. I was surprised to read that this grant was first introduced in 1984 as it was awarded to me (albeit under the auspices of The Institution of Mining and Metallurgy, London) as long ago as 1964, and I spent two very profitable months in Sweden at that time. Training in job-skills * A South African mine is leading the way in providing alternative job-skills to staff in a bid to upgrade services in local communities and create greater economic empowerment. In recent months, 85 employees of the Associated Manganese Mine (ASSMANG) in the Western Cape have learnt skills as diverse as candlemaking, shoemaking, concrete-product manufacturing, and brick production through a newly established community training centre.

Jan 1, 1993

Members are advised that the Council has decided to change the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. By making this change we will be conforming to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Institutes. While making these changes, the opportunity is taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Council trusts that these changes will meet with the approval of members.

By M. G. Demmer

South Africa ranks among the top three mineral producing countries in the world, and yet the country's teaching and student population have a very limited knowledge of the mining and metallurgical industry. This is probably one of the major reasons why so few scholars elect to study mining-related disciplines at local universities, or to consider a career in the industry. Small mines Much interest in the development of small mines has been evident in the past few years, with junior companies taking the bull by the horns and moving in where larger companies found it uneconomic to tread or, indeed, where large companies are foresighted enough to see the advantage of smaller operations. Examples of small mines are to be found from Europe to Australia, in the Americas, and in

Jan 1, 1986

The sixth University of Stelenbosch (US)/University of Cape Town (UCT) Minerals Processing Symposium was held at the University of Cape Town on Friday, 7th August, 1987, and was sponsored by The South African Institute of Mining and Metallurgy (SAIMM). Once again the Symposium attracted a large number of delegates from the mining, metallurgical, and chemical industries. Uranium and electricity A symposium on 'Uranium and Electricity- The Complete Nuclear Fuel Cycle' will be held in Saskatoon, Canada, during 18th to 20th September, 1988. The Symposium is sponsored by the Canadian Nuclear Society. Electric steel The Institute of Metals, organizers of the 3rd European Electric Steel Congress, have announced that this important international event will take place in October 1989 at the Bournemouth International Centre.

Jan 1, 1987

By B. Litt, D. L. Van Coller

Job evaluation and the changing wage pattern by D. L. VAN COLLER, B.A.(Cape Town), M.A., B.Litt.{Oxon.) (Visitor) This paper sets out to show how changing forces are affecting the techniques that have been used in the evaluation of Black jobs on gold mines in the Anglo American Group since the introduction of job evaluation in 1961. Initially, job evaluation was essentially a management tool designed to differentiate jobs in a limited skill spectrum and thereby permit the establishment of a 'many stepped' job ladder for Black employees to climb. With the changing wage pattern, job evaluation is becoming an industrialrelations tool aimed at recognizing the skill and effort contributed by the worker so that the pay relationships between jobs are seen to be equitable by the employees.

Jan 8, 1974

By J P. van Dyk

The dramatic strengthening of the rand against the dollar as well as a decline in quantity and quality of locally available concentrates have had a dramatic impact on Zincor?s operations during the previous two years. Zincor has responded with the implementation of a number of technical improvements to the process to decrease cost and increase revenue and plant flexibility. Among the initiatives is the pre-leaching and pelletising of the zinc concentrate, de-bottlenecking and process improvements in the leach and purification circuits, the introduction of cathode washing and automated cathode stacking in the cell house and the installation of a new furnace to produce pre-alloyed jumbos. This paper will describe these initiatives and others that Zincor have recently taken to stay competitive in changing global base metals market.

Jan 1, 2005

By D. R. Hardman, J. W. Oberholzer

Based on information supplied by South African collieries to the Coal Mining Laboratory of the Chamber of Mines since 1978, the paper outlines the general performance of the continuous miners used and gives the results more-detailed studies of the cutting, loading, and transportation processes. On average, the continuous miners produced coal at a rate of 76 t per operating hour, which, at an average machine availability of 67 per cent, resulted in a production of 51 t per total hour. The cutting rates varied between and 250 t/h but, owing to machine and system inefficiencies, the overall production rate varied between 92 and 48 It is concluded that, if the collieries concentrated on improving their machine utilization procedures and operating practices, they could increase the overall production from their continuous-miner sections.

Jan 1, 1987

By D. A. Viljoent

Historical Background The Empire Council of Mining and Metallurgical Institutions was formed during the early 1920s to foster the holding of British Empire Conferences, and today is representative of the following Institutes: Australasian Institute of Mining and Metallurgy Canadian Institute of Mining and Metallurgy Geological Society of South Africa Institute of Petroleum Institution of Metallurgists Institution of Mining and Metallurgy Institution of Mining Engineers Metals Society Mining, Geological and Metallurgical Institute of India South African Institute of Mining and Metallurgy South Wales Institute of Engineers. The first public suggestion for the formation of a Council that would link mining institutions in various parts of the British Empire came from Mr Frank Merricks, who, as President of the Institution of Mining and Metallurgy, was speaking at the annual dinner of the IMM in 1921.

Jan 1, 1981

By J. E. Friant, R. P. H. Willis, J. Maaren

Considerable effort is currently directed towards the development of non-explosive mining methods with the potential to allow continuous mining in narrow reef conditions. Besides improving productivity, continuous mining results in concentrated mining which has a significant impact on reducing infrastructure costs. CSIR: Miningtek recognized the potential of mini-disc cutters in a long or short wall application for selective hard rock mining in 1999. EEA was chartered to build a 780 mm diameter by 800 mm deep drum cutter head. While EEA designed and built the head, CSIR designed and built the drive mechanism and chassis for the trial machine. After assembly and shop testing at CSIR’s facility, the machine was shipped to a platinum mine for trials. This paper traces the development of mini-disc cutters and their application in South Africa.

Sep 1, 2001

By W. J. Cruise

This paper reports on a test that was conducted underground in a mine for two years on the following: pipes coated with paint, fusion-bonded powder, metal, or impregnated tape; and aluminium, stainless-steel, 3CR12, and plastic pipes. It was found that the degree of corrosivity and mechanical damage increases substantially from the shaft of a mine towards the stope. Thus, the range of coatings that can be used successfully is fairly large in the shaft and haulageways, but corrosion-resistant materials, especially corrosion-resistant steels, need to be used close to the stope. A study of the relative costs involved showed the costs of pipes of low-carbon steel and unplasticized polyvinyl chloride to be lowest, and those of epoxy-coated steel pipes to be highest.

Jan 1, 1985

By D. W. Boydell, E. B. Viljoen

A flowsheet incorporating rotary-drum filtration for the solid-liquid separation step, followed by solvent extraction for uranium purification, is used as a standard against which four flowsheets are compared. These flowsheets employ either counter current decantation or belt filtration for solid-liquid separation, and either solvent extraction or continuous ion exchange plus solvent extraction for the purification step. Sales revenue, taxation, capital expenditure, and operating costs are estimated. These factors are taken into account in the calculation of an incremental net present value for each circuit by the discounting of cash flows at 25 per cent per year over a projected life of 15 years. For the material used in these examples, the highest net present value results from the circuit that employs belt filtration followed by continuous ion exchange and solvent extraction.

Jan 1, 1978

By R. N. Guest

The Tromp distribution curve was used in an evaluation of gravity separators treating a synthetic ore made up of silica and marker minerals of various relative densities. The results pinpoint differences in the concentration of particles of different sizes, and indicate how the grade of a concentrate is likely to vary with particle size. An increase in the feed rate increased the efficiency of the 'waterless' spiral concentrator that was tested, but the multiport spiral concentrator tested was more efficient. Both spiral concentrators were found to be more efficient than the pinched sluice and the shaking table that were tested. The method was found to be a useful way of evaluating gravity concentrators, but, for ease of analysis, care must be taken in the choice of marker minerals.

Jan 1, 1985

By M. A. von Below, I. C. Robinson

A mineral economic analysis of South Africa's mineral-beneficiation industry, comprising both economic theory and case studies, suggests that the domestic market has proved to be a more effective vehicle for promoting the establishment of advanced beneficiation projects than the availability of domestic raw materials. Although the domestic market plays an important role in the promotion of beneficiation by providing a secure outlet for sales, its most vital role is in the development of technological and marketing know-how that may give South African beneficiated products the competitive advantage required to penetrate export markets. The real wealth of a country lies primarily in the skills of its people rather than in its natural resources, and the domestic market plays a pivotal role in the development of these skills.

Jan 1, 1990

By M. I. Brittan, E. J. J. van Vuuren

Computer analysis, modelling and optimization of gold recovery plants of the Anglo American Group by M. I. BRITTAN M.Sc. (Eng.), M.S., Ph. D., (Member). and E. J. J. van VUUREN M.Sc., (Visitor). Multiple correlation and regression techniques are used to analyse gold plant operating records. Key variables m the process which Influence the gold recovery are Identified and assembled into a mathematical model. This constitutes a valuable tool for the optimisation of variables such as the rates of reagent addition and for assessing the economics of extending the plant. Substantial short term economic benefits have been realized. The techniques provide a rapid diagnostic service without interfering with normal plant operation. Quantitative results are presented and their implications examined. The value of the method is discussed.

By S. Budavari

On the one-hundredth anniversary of the founding of the South African School of Mines, this paper presents a historical review of the tertiary mining education carried out by the School of Mines in Kimberley and the subsequent institutions in Johannesburg. In addition to recording and evaluating a century of mining education, it describes the current activities of the Department of Mining Engineering at the University of the Witwatersrand, which is believed to be the natural successor to the School of Mines. The comparison of earlier and contemporary academic mining activities reflects a gradual transition from the educational philosophy and objectives of a school of mines to those of a modem university department. In the conclusions, some aspects of the educational effort expended during the past hundred years are briefly highlighted.

Jan 1, 1996

By A. A. Snodgaass

This paper reviews lead as a commodity, starting with a brief historical outline and dealing with the various uses of lead in some detail. It then goes on to discuss some statistics in relation to the production and reserves of lead, before sketching its mode of occurence. The topics are approached in regard both to the world and to South Africa, with the emphasis on the later. The mining and concentration of lead at Black Mountain Mine at Aggeneys in the north-western Cape Province are detailed, before a general account is given of the smelting, hydrometalurgical extraction, and refining of lead, together with the processes used in these activities. The paper concludes with a discussion of safety and health in regard to lead and a brief look at the commodity's future.

Jan 1, 1986

By SAIMM Journal

COLLOQUIUM ON COMMINUTION The Institute has arranged a colloquium on the above topic to be held on 13th March, 1973, at Kelvin House. The following papers will be presented: 'Peripheral Discharge Mill', by A. H. Mokken, Union Corporation Limited

Jan 1, 1974

By John Freer

The time 06h30 in midwinter is a little early to set out on an excursion from Johannesburg. Yet this was the hour that members, many accompanied by their wives, started to assemble in the parking lot adjacent to the squash courts at the Wanderers Club, Illovo, for a visit to Premier Diamond Mine at Cullinan. All fifty were checked in and aboard the coach by 07hOO. Coffee and sandwiches, served en route by Doris Gardner and Pam Binstead, were most welcome. IMM awards Given below are details of the trust funds, etc., to which applications are invited for grants, etc., payable in 1985. Application forms, which must be returned to the Secretary before 15th March, 1985, are available on request. Applicants should note that, in general, preference will be given to members of the Institution.

Jan 1, 1984