Search Documents

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. This sludge is a result of reacting limestone with sulfur dioxide to precipitate calcium sulfite and calcium sulfate. The majority of the sludge is simply landfilled, but with increasing landfillimg costs this can cost the plant millions of dollars per year. As a result, this option is rapidly becoming less attractive. Producing marketable materials from the sludge is a far more promising avenue, provided that the products can meet the necessary specifications at a reasonable cost. In this paper, a method is described for using froth flotation and water-only cyclones to remove unreacted limestone from scrubber sludge. The water-only cyclone was found to be very effective for removing the coarser unreacted limestone, grinding ball chips, gravel, and similar coarse impurities. Froth flotation was found to remove fine unreacted limestone, with a minimum of reagent addition.

Jan 1, 1995

By S. Svoronos, B. Moudgil, R. Stana, A. El-Midany

Due to their similar surface properties, it is not always easy to separate carbonate minerals from other salt type minerals by froth flotation. A particular example is the difficulty of separating dolomite impunities from phosphate minerals. Such challenging fundamental and practical problems have inspired several research efforts in various laboratories around the globe to find methods for economically removing the dolomite. However, a universal and cost effective process is not in commercial use. In this paper, a new process for separation of carbonate minerals (dolomite or calate) from other associated minerals is presented. Differential solubility of carbonates in slightly acidic solution is utilized to generate micro GO, bubbles at the carbonate mineral/ water interface. Particle (e.g., dolomite)/ bubble aggregates float to the surface leaving phosphate concentrate with low MgO content. Interestingly, up to 6.0 mm particles can be floated by such micro bubble/particle aggregates. Different sutface-active agents were tested to stabilize the bubbles. Results of these tests are presented and the mechanisms involved are discussed.

Jan 1, 2005

By Betty L. Gibbs

A clear and accurate knowledge of the status of ventilation in an underground mine is essential to continuing safe operation. In a small mine with a few working faces, the problem is simple and can easily be solved by choosing the appropriate fan. In larger, more complex mines the problem of supplying the working faces with fresh air is a problem beyond the scope of 'finger in the wind' analysis. In today's climate of stiffer government regulation and mining company concern for the safety of workers, computer programs which analyze ventilation networks are helping mining companies meet the standards. The development of computer programs for ventilation network analysis is summarized. Early programs were developed at universities or government agencies and required large expensive computers. As computers have become smaller and less expensive, the development or revision of programs for micro computers has become more available. Prices have lowered to the point of affordability even for medium and small companies. A list of ventilation network analysis programs is provided along with a summary of capabilities, costs, and hardware requirements for each program.

Jan 1, 1987

By Michel David

Once a mineralized body has been delineated, drilled and estimated from surface samples, it often happens that before the final go-no-go decision is taken, an underground sampling program is decided, very often via a ramp which hopefully will be later used to extract the ore. The cost of such a program can be close to a million dollars. On other occasions, when a property changes hands and is reexamined maybe 20 years after the original drilling program, a "check sampling" program is carefully, designed to make "sure" that the old assays are "correct". One may fear poor sampling practice in old days, or deliberate highgrading by promoters. Again one may be talking of resampling cost which may be in the six-figures range. Other similar situations include the drilling of a few large diameter holes to ascertain the validity of a majority of small diameter drill holes, or auger drilling, or back-rimming. In uranium checking radiometric information is also a problem related to the above ones.

Jan 1, 1979

By R. L. Grayson, S. Yuan

A stochastic model for evaluating the impact of the reliability and maintainability of shovels and trucks on the operational effectiveness of shovel-truck mining systems is presented. In the model, the Markov modeling technique is used to analyze the operating status of a shovel-truck mining system. Then, simulation is used to study the productivity of a shovel-truck system in a particular state. Finally, the relationship between the effectiveness of a shovel-truck system in terms of productivity and the reliability and maintainability of equipment is established. This relationship may be very useful to mine managers in making decisions in surface mining (e.g., regarding production process control, equipment replacement, and maintenance planning). A quantitative study is given to demonstrate how the reliability and maintainability of equipment affect the system effectiveness and how to pinpoint the parameter that has the most significant effect on the system effectiveness. The quantitative study indicated that in order to improve the system effectiveness significantly, the reliability and maintainability of the equipment need to be improved simultaneously.

Jan 1, 1995

The stability of mine roofs in permafrost zones is determined mainly by temperature and ice content. The deformation resulting from creep and temperature-dependent physical properties of frozen rock mass is the dominant component of total deformation. Roof bolts can consolidate the roof and control its deformation. In this paper, a finite-element model, for the analysis of the effects of roof bolting in a frozen rock mass is presented. The model includes the variables normally encountered when analyzing the effects of roof bolting in rocks. It also accounts for properties unique to frozen rock mass: creep deformation and the change in Young's modulus with changing temperature. The model shows that, as bolt spacing decreases, there is a trade-off between increased roof stability from increased mechanical support and decreased stability from increased conduction of heat into the frozen roof. This result was expected and shows that, for a given set of rock-mass conditions, including ice content, temperature, particle size, etc., there is an optimum bolt length and bolt density for minimum roof deflection.

Jan 1, 1997

By B. Mather

I was very glad to see an article on alkali-silica reactivity of concrete aggregate in Mining Engineering. It is a topic that should be reexamined every 45 or 50 years. The last paper (that I am aware of) that examined this topic in Mining Engineering was Rexford (1950), who, at the time, was chief of the Petrography Section, South Pacific Division Laboratory, Corps of Engineers, Los Angeles, CA. The paper was presented at the AIME meeting in Los Angeles in October 1948. Professor Leming's discussion generally reflects the current state-of-the-art; but it provides no references for more detailed information. I wrote a paper titled "How to avoid excessive expansion of concrete due to alkali-aggregate reaction," which was included in the Proceedings of the Second International Conference on Alkali-Aggregate Reactions in Hydroelectric Plants and Dams (Mather, 1995). In it, I emphasized that it was the hydroxide ion (not the alkali ion) that caused the pore fluid in the concrete to dissolve reactive silica, producing alkali-silica gel capable of taking up water, thereby, causing swelling and rupturing of the concrete. Excessive expansion will not occur unless there is a sufficient amount of potentially expansive alkali-silica reaction product and water. However, this will not occur unless there is a sufficient quantity of reactive aggregate and unless there is a mechanism by which the pH of the pore fluid can get well above the normal value of about 12.6. In many cases it is sufficient that the cementitious medium not only contains portland cement but also contains ground granulated blast-furnace slag (GGBFS) or a pozzolan such as fly ash, silica fume, metakaolin, volcanic glass or calcined shale - any of which may have been included for economic reasons. If, however, the person selecting the ingredients for concrete knows that the aggregate is reactive (with no alternate nonreactive aggregate available) and if the person knows that the only available portland cement has a high alkali content (i.e., more than 0.6% Na2O.; Na2e = % Na20 + 0.658 x % K20), then it becomes irresponsible not to establish what reasonable precaution one should take. Professor Leming suggests using one of the following: 30% Class F fly ash, 50% GGBFS or 7% to 10% silica fume. My view is that one should prepare test specimens with the cement and aggregate to be used and then expose these both with and without at least two dosages of each of the various alternative materials (slag, pozzolan and lithium salts), so that the required dosage. to control the expansion is established. Then, economic considerations can dictate the final selection. I would point out to the author that GGBFS is not a pozzolan and is not an admixture, but, rather, it is a latent hydraulic cement. An admixture is, by definition, a material other than hydraulic cement. I commend him for suggesting that aggregate producers should become more active in knowing about the reactivity of their products and the precautions needed to permit those products to be safely used in concrete.

Jan 1, 1997

By Leonid Pevzner, Valerie Dmitriev, Yuri Babitchev

Performance of belt conveyors, service life of belts and mechanical elements can be radically improved if the automatic adjustment of the belt speed movement is made in such a way, that the unit load over the conveyor length be constant and close to the rated one under random input freight traffic. Such an adjustment is possible when the system of a controllable thyristor electric drive on the basis of induction squirrel cage motor is used. Computer-aided adjustment of the belt conveyor movement is effected via bicontour digital control of the main drive in order to redistribute loads when the loading of conveyor and contour of the control of tension drive are changed. The system envisages control and condition monitoring of the conveyor electromechanical system, as well as metering of electrical power and the amount of conveyor freight. The results of the simulation of speed control of the conveyor belt are given in the report. Mathematical model of the conveyor electromechanical system describes the movement of the belt with cargo and the tension drive. The input cargo traffic is assumed as stationary ergidic random process with the assigned characteristics. The solution of the problem of the synthesis of a closed-loop control system, the structure and parameters of adjustment, the conditions of asymptotic stability of the control back-up system and the condition of minimization of mean square error of shadowing are also given in the report. Microprocessor controller is used to realize the function of the adjustment unit. Under this control system standard mode of conveyor operation, different modes of start-up, operating mode with decreased speed when transporting people, service and emergency braking of a conveyor and some other modes are realized. The digital model of a conveyor as an instrument for decision making in case of emergency is used in those modes. MASTER TEXT Long-standing practice of belt conveyor operation in mines of Russia has proved their inefficient use with 40-70% capacity and 20-25% availability factor. It is associated with unreasonable power intensity and reduction of service life of mechanical components, and as a result, with the growth of total transportation costs. Low efficiency of conveyor application can be explained by the extremely irregular distribution of conveyor freight traffic. Usually, the width of a conveyor belt is identified in accordance with the possible maximum traffic value, engine power capacity for long-term operation under rated loads. However, actually a conveyor often runs without any load and its average load in most cases is lower than the rated one. The problem can be eliminated by way of the adjustment of the operational mode of a conveyor according to an actual input freight traffic via belt speed control providing for the conveyor regular linear load which is nearly equivalent to the rated one. Experimental research into freight traffic under working conditions of the operating underground and open-cast mines proves the fact that the actual freight traffic can be adequately presented through the model of stationary random function of time, for ex- ample, as a J (t) continuous random Gaussian process that is modulated with a G(t) elementary pulse flow:

Jan 1, 1996

By Emmanuel J. Voulgaris

The ?Milos Conferences? is an activity of the non-profit organization ?Milos Conference Center - George Eliopoulos?, located on the island of Milos, Greece. The objective of the ?Milos Conferences? is to create the conditions for interaction among different disciplines of academia and industry, and dissemination of the cutting edge between scientific and technological development. The young scientists are our special aim. The governing body of the ?Milos Conferences? is the ?Milos Conferences Council?. The president of the Council is Mrs. Kitty Kyriacopoulos - founder of the ?Milos Conference Center - George Eliopoulos?, and the members are from academia and industry. The planning and the organization of all conferences are carried out by the ?Heliotopos Professional Congress Organizers? in Athens. The venue is always the ?Milos Conference Center - George Eliopoulos? on the island of Milos. The ?Milos Conferences? comprise of different conference series, each devoted to a general subject. This book covers the proceedings of the ?International Conference on Sustainable Development Indicators in the Mineral Industries?, (SDIMI), a conference of the series under the general title ?Restoring the Natural Balance?.

Jan 1, 2003

By Keith Whiting

The Little Boulder Creek molybdenum deposit is in central Idaho, in the White Cloud Range about 3.2 km (2 miles) northeast of Castle Peak, the highest peak in the range. The elevation of the deposit is about 2591 m (8500 ft). The deposit is accessible only by helicopter or by a 12.9-km (8-mile) trail from the county road along the East Fork of the Salmon River. The nearest towns are Clayton [25.7 km (16 miles) northeast], Stanley [33.8 km (21 miles) northwest], and Ketchum [45 km (28 miles) south-southeast]. The principal known deposit at Little Boulder Creek is called the "North Zone." In this zone, the molybdenite occurs both in stock- work veinlets and disseminated through metamorphosed quartzite of Pennsylvanian age. Pyrite is ubiquitous, averaging perhaps 0.05%. Scheelite and/or powellite are present in trace amounts. An intrusive quartz monzonite stock, probably of Cretaceous age, bounds the deposit on the west. A steep fault which drops Tertiary age Challis volcanics into contact with the mineralization limits the deposit on the east.

Jan 1, 1991

By A. Pavlides

The purpose of this study is to compare estimation methods for lignite reserves at the Amyndeo mine and to provide a map of the estimated thickness of the coal seams. The reserves are first estimated with the method of Voronoi diagrams, using a group of mirror points to close the polygons around the boundaries of the mine. The second estimation method is based on Ordinary Kriging using the Spartan variogram model. Finally, the reserves are estimated by the mean lignite thickness value of the drill-hole data Two data sets are investigated. The first one corresponds to an exhausted part of the mine. The derived reserves estimates are compared with the actual data obtained by the Public Power Corporation (PPC) to validate the analysis. The second data set extends over the entire mine, and it is used to derive an approximate estimate of the total lignite reserves. A geostatistical analysis of the total layer thickness is performed. An interpolated kriging map of the total thickness variation is produced accompanied by a map of the kriging uncertainty.

Jan 1, 2008

By Leonard Harris

Mining is a business and, therefore, is expected to make profit for its investors, like any other business. It is a risky business which requires the expertise of professionals from several disciplines to make it successful in the finding, evaluation and development of a new mining venture. Many of the same disciplines, as well as experts in some other fields are required to operate the facilities once they are built. To manage all this, wide-ranging, versatile and sharp managerial skills are required. On the U.S. domestic front, the most important management issues requiring attention today and tomorrow are the increasing unwarranted attacks by anti-mining groups and legislators on the industry and aided by an unchallenged, but widespread, public view that mining is not necessary and damages the environment. Higher costs to mine and process deeper and more refractory ores are also of great concern. More and more attention is being focused, therefore, on overseas projects under the belief that undeveloped countries will recognize the economic value of mineral production and that lower costs can be achieved.

Jan 1, 1993

By J. M. Baker

It seems appropriate here to open with a quotation from the great pre-Confucian philosopher Lao-tze: "The softest thing in the world dashes against and overcomes the hardest. There is nothing in the world softer or weaker than water, and yet for attacking things that are firm and strong there is nothing that can take precedence of it." I am happy to report that our system of mining has worked out, with minor modifications, as well or better than was predicted. This, in a period of rising labor and material costs, has been most gratifying. Gilsonite is a solid hydrocarbon which occurs in vertical fissures cutting the sandstone and shale beds of the Uintah formation in south¬eastern Utah. It is found in other parts of the world under similar occurrence but nowhere else is it now being mined commercially. The Gilsonite veins on entering the shale members of the Green¬river formation break into small veinlets separated by shale, These veinlets are not now economical to mine.

Jan 1, 1959

By Paul H. Lu

This paper proposes a novel method, "integrity factor approach," of mine-pillar stability evaluation based on in situ triaxial-loading measurement. The pillar integrity factor is defined as the quotient resulting from division of integrated total pillar strength across the critical dimension by the integrated total pillar load across the same dimension. The integrity factor is dynamic, while the conventional safety factor is static. With this approach, the pillar stability can be evaluated at any stage of mining progress during panel operation. It automatically considers the progressive failure of the pillar and post-failure strength without the need to clearly define the boundary between yielded and intact zones of the pillar. Based on two case studies, the integrity factor approach is shown to be a practical, effective technique for evaluating stability of conventionally designed pillars. It is suggested that a more realistic estimate of in situ pillar strength could be made based on the combination of in situ triaxial-loading measurements and laboratory true triaxial compression tests, rather than through the traditional combination of biaxial-loading measurements and conventional triaxial compression tests.

Jan 1, 1986

By R. Owens, C. Roos, B. Hill, S. Rosenthal

It is common practice, and even legally required in many jurisdictions, to design two-lane haul roads in open pit mines to three and a half times the widest dimension of the haul trucks operating on the road. In open pit gold mines with high strip ratios, the road width has a significant impact on the economics of a design. It is possible to minimize the flattening of the highwall if the road width is reduced, assuming the width used is not needed to flatten the slopes for geotechnical purposes. With the use of autonomous haulage and pullouts, it may be possible to operate safely and efficiently on a reduced road width of two times the width of the hauling equipment.

Mar 2, 2022

By William F. Hahn

It is a pleasure to speak to this group about special crusher installations which are in the bauxite and phosphate rock processing industries. The installations to be discussed demonstrate the variety of conditions, materials, and results desired which must be evaluated before a selection is made from the specialized crusher technology available today. Those of you who are closely involved with phosphate rock and phosphate products processing will find some of this information a bit interesting and perhaps alien to your own descriptions or every day references. It is given from a "crusher" manufacturer's viewpoint and therefore is infused With our flair and language. General features of six (6) different crushers will be shown in cross-section With slides and will be discussed in the same order.

Jan 1, 1978

Shallow ore deposits are mined by surface methods but a depth is reached in the case of most deposits after which underground methods are applied for the extraction of the remaining ore. The determination of this depth and its analysis is the subject of this paper. In order to determine transition depth from open-pit to underground mining on the basis of the allowable and economically feasible overall stripping ratios, an economic-mathematical equation is first introduced. Using the achieved equation and an analytical procedure on a particular two-dimensional hypothetical tabulate deposit, an effective formula is then established. The formula introduced here, together with the procedure adopted, could be used in all similar mining situations by the mining design engineer.

Jan 1, 2010

By P. Huttagosol

The use of computer models to design ultimate pit limits during feasibility study and long range mine planning is becoming a significant practice in open pit mining. One of the problems in determining optimal ultimate pit limits using true optimization techniques has been they require a great deal of computer memory and execution time. In this paper, the maximum closure of a graph, which is a true optimizing model developed by Lerchs and Grossmann, is modified for solving ultimate pit limit problems. By using some properties of the original L&G graph algorithm, the tree configuration can be reduced to only connections between positive ore nodes. The modified algorithm is shown to require less memory and processing time while still yielding an optimal solution.

Jan 1, 1989

By C. J. Gauvin

The Geological Department, headed by the Chief Geologist, is part of the General Engineering Division and is under the direct supervision of the Chief Engineer. The Geological Department is responsible for the technical direction of all work concerned with the finding and outlining of ore. It provides the mine operating staffs, with the necessary plans and sections to enable them to design pit and underground layouts and to, extract ores' as required by outgoing cargoes. The department maintains grade and ore reserve statistics in conjunction with a mining recovery factor at year-end. These duties are performed through the co-operation of all departments participating in the overall operation. As a result, a steadily broadening use is being made of geology at Steep Rock.

Jan 1, 1960

By M. D. Dennis

Precious metal mineralization at Mt. Hamilton" Nevada is associated with a poly-metallic, garnet-pyroxene skarn system developed in middle to upper Cambrian calcareous shales, limestones and dolomites. The skarn is developed around the Cretaceous Seligman and Monte cristo calc-alkaline stocks. Gold is associated with intense retrograde alteration. Later epithermal quartz veins containing gold, silver, base-metal sulfides, and sulfosalts cross-cut skarn alteration. Westmont Mining Inc. is currently developing two mineralized zones containing a geologic resource of approximately 7.7 M.T., which averages 0.05 OPT gold and 0.5 OPT silver. The project will have an estimated mine life of seven years, with a planned annual production rate of 35,000 ounces of gold and 300,000 ounces of silver.

Jan 1, 1989