Search Documents

By T. Matthews

"One critical factor in mineral reserves reporting, as well as mine-reserves reconciliation, is the impact of dilution and ore loss in the mining process. This paper considers the implications of various factors on dilution and ore loss projections, by orebody geometry, mining method, and ore control systems. We also discuss the implications of resource estimation methodology on dilution for reserves. DEFINITIONS Dilution and ore loss are two critical concepts in mining, which address the differences encountered between modeled grade and tonnages and actual production. Dilution is volume increase and grade reduction caused by multiple factors, chief among which are mining of waste material along ore-waste contacts, mining of internal waste as ore, and misclassification of waste as ore in the ore control process. There are also geostatistical and estimation aspects sometimes lumped with dilution, including the volume-variance effect (the tendency for small volumes of material to include a less regular distribution of grade than large volumes of material). Ore loss is described as reductions of ore volumes in the mining process due to misclassification of ore as waste in the ore control process, exclusion of discontinuous mineralization from mining due to geometry or continuity, and mechanical losses in the mining process. Dilution is typically taken as an increase in tonnes of ore with no change in contained metal (and thus results in a reduction in grade.) (Some workers consider the likely grade of the diluting material as well, particularly in deposits with gradational grade boundaries—this will be addressed later in the text.) Ore loss is typically taken as a reduction in tonnes at average grade of the ore, and thus results in a reduction in both tonnes and contained metal. If model (resource) tonnes are Mt, grade is Mg, and contained metal is Mm, the resource with ore loss (L) and dilution (D) included (Rt, Rg, and Rm) will be:"

Jan 1, 2015

By J. A. Finch

The use of pneumatic methods for measuring interface level in flotation columns is analysed. It is shown that errors can vary over a wide range (e.g. 40 cm. in one industrial application) depending on bubble size, particle size, bubble loading, liquid hold-up and bulk slurry density. Accurate measurements (+ 5 cm) can be obtained by measuring intensive properties of the froth near the interface. Methods based on the measurement of temperature and conductivity are described and analysed. Control of the interface level using these measurements subject to various disturbances is demonstrated.

Jan 1, 1988

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, J. Brent Hiskey, Gürses Öner

Currently there is considerable interest in applying in situ leaching technology to recover copper from oxide ores. In many instances, the distribution of copper mineralization in these deposits is fracture controlled. Laboratory core-leaching experiments have demonstrated that leaching response is sensitive to the dissolution of copper from and the formation of channels along main fractures. Solution short- circuiting can be a major limitation of this technology. This paper describes the application of macromolecular polymers to achieve flow-profile control during leaching. Pre- and post-leached fractures were characterized by computerized tomography (CT) analysis.

Jan 1, 1993

By D. Tao

Coal is a major source of energy in the U.S. and more than 51% of the electricity used in the country is generated from coal. Coal cleaning prior to combustion is necessary and often accomplished using wet physical processes at coal preparation plants to remove impurities such as ash, sulfur, mercury. However, the resultant clean coal product still contains a significant amount of impurity due to the fact that impurities are not well liberated from coal particles ranging from several millimeters to inches in size at which wet cleaning processes take place. A cleaner coal product can be obtained if a cost-effective dry process is developed to further clean pulverized and thus better liberated fine coal at the power plants prior to its combustion. The benefit of such a process is a significant reduction in the cost of expensive post-combustion chemical cleaning processes such as flue gas scrubbing employed to meet the stringent environmental air quality regulations. In this study, a novel rotary triboelectrostatic separator (RTS) was investigated for its application to dry cleaning of fine coal samples acquired from the power plants in the state of Illinois. The pulverized fine coal contains well liberated ash and pyrite minerals and is an ideal feed to the triboelectrostatic separator for further cleaning without the use of water or any chemical reagents. The proprietary rotary triboelectrostatic separator (RTS) is characterized by an innovative high efficiency rotary charger, charger electrification, laminar air flow, and specially designed electrodes. Compared to existing triboelectrostatic separators, the rotary triboelectrostatic separator offers significant advantages in particle charging efficiency, solids throughput, separation efficiency, applicable particle size range, etc. Testing with several fine coal samples has demonstrated that this technology can significantly reduce ash content with a process efficiency similar to or better than froth flotation. Important process parameters such as charger rotation speed, injection and co-flow rate, feed rate were investigated for their effects on separation performance.

Jan 1, 2010

By Pieter Hoekstra, Jim Hild, Mark Blohm

In the Basin and Range Province of Nevada, geophysics is used to assist exploration for bulk minable gold deposits, particularly over pediments. It is employed for mapping thickness of alluvium and Tertiary valley fill, for mapping covered structures, and for identifying alteration zones. In addition to potential field and seismic methods, three different electrical and electromagnetic methods are frequently used, resistivity-induced polarization, controlled source audiomagnetotellurics, and time domain EM. A review and comparison of the principles of these methods, illustrated by case histories, is the topic of this paper.

Jan 1, 1989

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, Ronald J. Roman

The hydrodynamics of the leaching solution in leach heaps is known to be one of the important variables in the performance of the heap. The solution hydrodynamics are also important in the decommissioning of a heap where the aim is to flush out the residual dissolved metals and the remaining reagents. Chemical engineers have studied the hydrodynamics of "trickle bed" reactors for 40 years in an attempt to relate the performance of trickle bed reactors to flow conditions. Their work is reviewed with emphases on areas of similarity to heap leaching.

Jan 1, 1993

By M. Scherbakov, W. Shi

Abrasion is an important mode of performance for any element of an engineered product that involves material contact for example, a conveyor belt cover. Abrasion resistance is considered to be one of the leading factors in belt cover design and improvement. Various types of abrasion testing are reviewed by and compared to actual belt applications. A new quantitative screening torsional abrasion test is developed by Goodyear to mimic a dynamic contact between belt cover and differently shaped stones of various weights dropped onto belt at any angle, velocity and height.

Jan 1, 2004

The purpose of this paper is to describe two systems designed to provide estimations in stratigraphic orebodies for the purposes of detailed mine planning. The first is a completely geostatistical approach and the second is a combined geostatistical/deterministic approach. The essential features of both systems are the estimation of stratigraphic ore boundaries and the subsequent use of those boundaries to provide stratigraphic (or zonal) control for block and point grade estimation (kriging). Both systems are illustrated by application to a section of, the Hilton orebodies, Queensland, Australia.

Jan 1, 1989

By D. Diekman

Perlite is not a trade name but a generic term for naturally occurring siliceous volcanic rock. A distinguishing feature which sets perlite apart from other volcanic glasses is that when heated to a suitable point in its softening range, it expands 5 to 20 times its original volume. This expansion is due to the presence of 2% to 6% combined water in the crude perlite rock. When quickly heated above 1600°F (871°C) crude perlite pops in a manner similar to popcorn. The combined water vaporizes and creates countless tiny bubbles in the heat softened glassy particles. It is these tiny glass sealed bubbles which account for the amazing lightweight and other exceptional physical properties of expanded perlite. The bulk densities of the expanded perlite generally range from 3 pounds per cubic foot (48 Kg M3) to 10 pounds per cubic foot (160 Kg H3).

Jan 1, 1985

By Rodolfo V. de la Cruz

The broad front concept is based on the principle that gasification can be achieved more efficiently and completely from a plane broad combustion front in contrast to other geometries obtainable with current methods of gasification. By restricting combustion to a plane broad front, the ideal condition for gasification is achieved. A plane broad combustion front can be developed in coal by initiating and propagating combustion from the walls of an oriented channel and collecting product gases from another similarly oriented channel. Flow will then be directed along the highest permeability of the coal bed, the available cross-sectional area for fluid flow is substantially increased and, more importantly, the increased flow will be uniformly distributed throughout the whole mass of coal. The success of the method is greatly dependent on how well an initial and rigorous permeability survey and associated corrective measures yield a well-characterized coal bed. To maintain uniform reaction rates, the advance of the combustion front is located with pressure- or mass flow-transducers. These sensors are then connected to servo-controlled mufflers for controlling segments of the fire front which are advancing ahead of others. Finally, the development of the concept to overcome problems of roof collapse, reactant and product gas leakages, and water invasion are briefly summarized.

Jan 1, 1976

By S. Chander

The effect of pretreatment potential on the response of a gold electrode for Eh measurements in sulfide solutions was examined in terms of measured Eh values and electrode response time. The electrode response time is defined as the time required for the electrode to reach a steady-state value. The relationship between measured Eh values and the hydrosulfide ion concentration is established. The effect of pH, the reversibility of the gold electrode in the sulfide solutions, and the reproducibility of measurements are also investigated. A mixed potential theory is proposed to explain the observations.

Jan 1, 1989

By C. Bazin, D. Hodouin

Dynamic experiments were performed in a continuous open-circuit 40x40-cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transferfunction and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model, a minimum variance controller with constrained input is designed and its performances are compared, by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By R. S. Austin

One-third of the world's and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. Properly selected and refined, kaolin is an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

By F. M. Doyle, P. E. Richardson, E. Peters

A number of studies have attempted to correlate the semiconducting properties of mineral sulfides with their chemical reactivity. Frequently such studies are conducted on polished or abraded electrodes. Defects produced by abrasion may mask the influence of the semiconducting properties of electrodes, e.g., by pinning the Fermi level at the surface or by reducing the lifetimes of photogenerated charge carriers. It is shown that pyrite and galena electrodes have photocurrents that are extremely sensitive to abrasion of the electrodes. On freshly fractured galena surfaces, the space charge layer is readily polarized. Wet-abrasion is shown to produce a relatively thick ptype layer on galena electrodes and this p-type layer has a pronounced effect on the photoresponse. On freshly fractured pyrite surfaces, the Fermi level at the surface is pinned by a surface state. Wet-polishing reduces the magnitude of the photocurrent by over an order of magnitude.

Jan 1, 1993

By T. H. Jones

Fall of ground is a leading source of worker injury and fatality indicating a persistent need for ground monitoring technology. The HRTMM is an experimental convergence monitor utilizing a digital camera and custom software to track the position of one or more lasers across the target. Apparent laser movement is proportional to target convergence. The HRTMM was installed in an underground mine near active operations to test its response to the mining environment. This included intense blasting vibration and mine fog. Results and potential of the new monitoring technology will be discussed.

Jan 1, 2008

By Uday Kumar

This paper presents details of an availability study for a fleet of diesel engine operated load-haul-dump (LHD) machines used in a Swedish mine. For the purpose of this study, the LHD machines have been considered as a system comprised of many subsystems like engine, brake, transmission, etc., in series. As availability is dependent on both the reliability and maintainability characteristics of the system, together with reliability, the concepts of maintainability are also discussed. The need for exploring the data for the presence of any structure, which is very common in repairable system data sets, is emphasized with suitable examples. Simple graphical techniques are used for verifying the independent and identically distributed (IID) assumption for the data set. The error introduced due to the use of the exponential distribution in place of more appropriate distributions in estimation of availability and reliability characteristics is analysed.

Jan 1, 1989

By Robert L. Llewellyn

The Wharton No. 2 Mine of Eastern Gas and Fuel Associates is located about 60 miles south of Charleston, West Virginia in Boone County. Daily production is 6,000 T.P.D. on a two-shift basis. The Hernshaw Seam is mined by conventional equipment with one continuous miner in areas where conditions are suitable. The plant is on Cow Creek .Branch of Pond Fork, which in turn flows into the Little Coal River at Madison, West Virginia. When the mine was opened in 1948, plans were developed to build a dual Baum jig plant complete with mechanical and thermal drying, and because full production would not be reached for several years, it was decided to install only one Baum jig setup although the complete structure was erected. This phase of the plant was placed into operation early in 1949, The rated capacity was about 300 T.P.H. of 5" x 0 raw feed to the jig. Being a drift mine, the 10-ton mine cars are dumped at the Headhouse, crushed to 8" in a double roll crusher, conveyed 780 feet downhill to the picking .house where the +5" slate is removed by pickers. All coal is crushed to 5" and 5" x 0 is conveyed 150 feet to the cleaning plant. Further describing the plant growth, the second jig setup was installed in 1954 to clean the increased production. During this operating period, exhaustive tests had ,been run on the plant bleed which was an overflow from the large sludge tank located inside the plant, When the second jig addition was undertaken, 5-14' diameter and 12-8" diameter cyclones with a 9-disc filter were installed for the solids recovery and water clarification system, However, the circuit was not closed and a bleed of part of the overflows from the 8" diameter cyclones was still necessary, To comply with the State Water Commission regulations on stream pollution abatement, four pumps in series were installed to discharge the waste water behind the refuse pile.

Jan 1, 1959

By R. Fraher

The control of mine roof is of vital interest in underground coal mining not only for reasons of safety, but also to avoid the high costs of cleanup, resupport and production losses that can result from roof falls. The difficulty in determining roof stability mine-wide is due in large part to the broad variation of geologic and structural conditions that typically exist throughout a mining area. To ensure a stable roof over the entire mine, support systems must be selected to minimize the possibility of failure. The magnitude and cost of the support selected is a trade off against the cost of the number of falls that can still occur after it is installed. Because of the large number of variables involved in analyzing and optimizing roof stability versus support, a digital computer simulation was selected to find a cost effective solution to roof support design. A total cost approach is used which includes the actual cost of the roof support as well as the cost of the roof fall in terms of resupport and loss of production (Fraher 1990a). A Monte Carlo simulation program called ROCSIM (Roof control Optimization Cost SIMulation) has been developed for determining the optimum roof control system and design layout for underground room-and-pillar mining.

Jan 1, 1992

By J. G. Groppo, S. M. Khandrika, B. K. Parekh

It is shown that dewatering of fine coal particles (D50 = 21 µm) is enhanced near the point-of-zero-charge. The coal surface is modified by the addition of copper ions and by adjusting the pH to precipitate surface-active metal hydroxy species, which promote agglomeration and produce low-moisture cakes. Filtration kinetics data are used in calculating filter cake parameters from an integrated form of Darcy's law. The influence of copper ions and pH on filter cake parameters and the correlations among them are presented.

Jan 1, 1995

By A. M. Abouzeid, R. Hogg

Materials transport is involved in all phases of mineral processing. Bulk transport is necessary for moving materials between unit operations and through processing devices such as grinding mills. Differential transport is a primary mechanism for most separation processes. The basic mechanisms of transport and flow in particulate materials are reviewed and their role in materials handling and storage and in the performance of processing operations such as grinding and separation are discussed. Specific examples are used to illustrate current understanding of these transport phenomena and to indicate important research needs and opportunities.

Jan 1, 1989