Search Documents

By B. G. Long

Coastal States Energy Company (Coastal), a wholly-owned subsidiary of The Coastal Corporation of Houston, Texas, owns coal mining operations in Utah and Kentucky. One of the Utah operations, Southern Utah Fuel Company (SUFCo), located 30 miles west of Salina, Utah, has been operated by Coastal since 1974. This operation is a single-seam, six-section mine operated from one portal area. It produces 2.2 million tons of coal per year and has a payroll of approximately 300 employees, Coal is mined by continuous miners, hauled by diesel-powered haulers and transported by belt conveyor to outside crushing and screening facilities. Sized coal is hauled by contract truckers 80 miles to a unit-train facility located at Levan, Utah.

Jan 1, 1983

Compared to alternative ways of dealing with coal fines, oil agglomeration has always been a commercial bridesmaid and never yet a bride. Yet interest is high in the process, as shown by a number of pilot plants in operation that are funded by industry as well as government. In the past in the US, alternative ways to handle coal finer than 100 to 200 mesh included flotation, or no treatment except dewatering, or discarding the fines as waste. There are now a number of factors that tilt the economics more toward fine coal recovery. Today, the cost of mining a ton of underground coal runs from $22-30, and discarding even 10% as unrecovered fine coal is a real economic loss. A number of attempts (notably by EPRI) have been made to quantify the effect of coal cleaning on utility boiler operations. Transportation and ash handling costs, frequency of unscheduled outages, fouling and slagging problems, and boiler tube erosion are all lowered by cleaning coal. The advantage of coal cleaning on these parameters has been shown, but the dollar amount varies with many assumptions and is difficult to pin down. The message to a utility, however, has not been lost and the trend toward cleaner steam coal is accelerating. This may lead to fewer installations that only wash the coarse coal, and add back the unwashed fine coal until a maximum contractual ash limit is reached. And, as the proportion of coal fines continues to increase by continuous and longwall mining, it may become impossible to clean the coal sufficiently without cleaning the fines. Flotation and oil agglomeration are the only processes that presently deal directly with cleaning the very finest coal fractions. Flotation has proven its effectiveness in cleaning blackwater and in separating fine coal from mineral matter. It has the achievable potential for far greater pyrite rejection than is now obtained in commercial preparation plants. While flotation will continue to be the predominant method for fine coal cleaning, there are conditions and opportunities where oil agglomeration can be a

Jan 8, 1980

By Bernard A. Kilgore

Kaolin is a hydrated aluminum silicate mined primarily in middle Georgia along the "fall line", the location of the coast line in prehistoric times. It is used extensively as a filler for paper, insecticides, tires, plastics, a pigment for paints, as a coating for fine gloss paper, and for high grade ceramic products, such as catalytic converters. During its journey from the open pit mine to its final use, kaolin takes many forms, and must be handled in many different ways. The purpose of this presentation is to follow kaolin through its process and briefly describe some of the methods Georgia Kaolin Company, one of the world's largest kaolin producers, uses to handle and convey its product and some of the peculiarities involved.

Jan 1, 1983

By R. K. Singhal

In open pit mining every effort is made to maintain as steep a pit slope as possible. Pi t slope angles are influenced by numerous factors some natural that are amenable to limited or no control at all and other mining technology related where a greater degree of influence can be exerted by the engineer. One such area where control is possible is the method of drilling and blasting in the pit. This paper discusses the influence of blasting techniques on the economics of pit slopes and demonstrates how balanced blasting can be used with advantage to pit wall control and improve fragmentation (thus reducing material handling costs). Microprocessor based instrumentation to monitor drill and blast performance has also been described.

Jan 1, 1988

By Eero Pokki

The Päijänne Tunnel is being constructed to conduct raw water from Lake Päijänne to the Helsinki Metropolitan Area. The length of the tunnel will be 120 km and the cross-sectional area is 15.5 sq m. Excavation started in 1973 and will be completed in 1982. 94 km of the tunnel have been constructed from Lake Päijänne towards Helsinki. The construction has advanced according to plan, and due to Finland's hard bedrock there have not been any great surprises. When completed, the tunnel will meet the water requirements of the Helsinki Metropolitan Area for a long time in the future because, with a free fall of 36 m, 9.6 cu m/s of water can be conducted through the tunnel from Lake Päijänne to the Helsinki Area. With pumping it will be possible to obtain a flow of 15 cu m/s, although at first the discharge will only be 5 cu m/s. The tunnel was partly taken into service as early as March 1979 when it was possible to conduct water to the municipalities north of the Helsinki Area. It is already possible now to conduct water to Helsinki, too, but from the Korpimäki pumping station onwards it must be done through the River Vantaa, which is polluted. When the tunnel is completed in 1982, good quality water can be conducted from Lake Päijänne to the Helsinki Metropolitan Area through a continuous rock tunnel. The cost estimate in 1973 was $ 88 million while it is now $ 90 million notwithstanding high inflation. AREAS NEEDED FOR CONSTRUCTION The areas needed for construction were bought through voluntary deals. Areas of 4 - 5 hectares were bought along the tunnel line at about 5 km intervals. The excavation of access tunnels was started from these places, and the crushed rock from the main tunnel was also transported there. However, it was not necessary to buy the area

Jan 1, 1979

By J. E. Powell

Introduction The disposal of mine tailings, development rock, and other unwanted refuse material underground in mines by using pneumatic conveying techniques has been undertaken in the coal industry for many years. Similar equipment has been utilized for backfilling hard rock mines and is currently being applied in a gold mine in South Africa where development rock is being stowed in the mined-out stopes to help reduce the incidence of rock outbursts. On a limited scale, pneumatic conveying has been applied for backfilling uranium mines and one particular mine in New Mexico, U.S.A., has used this technique for 8 years. Other uranium mines in this area are now considerinq the dry backfill technique to eliminate the problems associated with hydraulic fill. The need to backfill in uranium mines is primarily of importance to improve ventilation, stabilize the pillars and roof, and possibly to extract a larger percentage of the uranium ore. If this can be achieved by utilizing the tailings from the beneficiation plant and using rock from the development headings which in itself may be slightly radioactive, then a greater benefit can be derived. Backfill can be achieved with hydraulic fill methods by running slurry into the stopes and allowing the water to decant and return through the footwall development entries to sumps for pumping to the surface. However there are several disadvantages associated with this method in that water is percolating throough the mine workings; it is necessary to build bulk heads in flat lying deposits; it is difficult to fill right to the back; and the decanted water takes with it quantities of the finer sand particles which results in maintenance problems with the mine pumps. Pneumatic conveying can overcome these problems in that the voids can be completely filled with high degree of compaction, heavy bulk heads are not necessary, the development rock can be added to the pneumatic system for disposal underground so eliminating hoisting cost to the surface, and cement can be added to the wetted material. To

Jan 1, 1980

By R. J. Sweigard

Differential settlement on reclaimed land presents a particular problem when the land is to be used for row crops. The poorly drained depressions caused by differential settlement restrict crop yield resulting in additional costs to alleviate the problem. Potentially more serious is the threat of failing to meet target yields due to settlement: related reductions. Because the mechanism by which the problem occurs is not well understood, a physical model study was conducted to investigate the importance of several factors. Although the importance of such factors as the relative amounts of rock and unconsolidated overburden in the undisturbed condition and the size distribution of rock fragments were considered, the analysis concentrated on the causes of settlement in the reconstructed soil layer above the rock spoil.

Jan 1, 1989

By R. J. Heath

Potassium, together with nitrogen and phosphorous, is one of the essential nutrients required for growth. All living things need potash and so the major demand for potash (approximately 95% of, total demand) is as a fertilizer. Traditional agricultural techniques relied on the return of organic materials to the soil to provide nutrient requirements and maintain soil fertility, and the prevailing low crop yields required little in the way of added fertilizers. But agricultural productivity has increased dramatically in recent times, and this increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows that there will always be a demand for potash. There is no substitute. Other fertilizers that contain N and P are complementary and not competing products.

Jan 1, 1987

By A. M. Johnson

Although known primarily for native copper, the Keweenaw Peninsula of northern Michigan also has deposits of copper sulfide (chalcocite) ore. A number of small, but rich, deposits are present at relatively shallow depths near the base of a thick, steeply dipping sequence of volcanic and sedimentary rocks. Because much of the ore is fracture-controlled, the deposits appear to be ideal candidates for in-situ leaching. Fracture mapping from drill core and borehole logs coupled with borehole packer permeability tests are being applied to evaluate the suitability of the ore for in-situ leaching. A leaching scheme utilizing a bacterial-assisted ferric iron lixiviant is being tested at bench scale. A pilot scale test is being designed to evaluate the system in the field.

Jan 1, 1988

By W. -C. Huang

In this paper, a methodology for the reliability assessment of geogrid-reinforced unpaved roadways is presented, by taking into account the variability of the subgrade?s undrained shear strength. Analyses are performed using the Point Estimate Method and the Monte Carlo simulations technique. The undrained shear strength is represented by its correlation with the California Bearing Ratio and it is modeled as a random variable following a long-normal distribution. Analyses are performed for different types of reinforcement. The study provides a quantitative assessment of the variation of the system?s probability of failure with this parameter. Overall, the approach suggested in this study may be considered as a complementary approach on the traditional concepts of global or partial safety factors.

Jan 1, 2008

By Parris A. Lyew-Ayee

This paper is the first preliminary report on the bauxites and terra rossas of the Caribbean. It concentrates on the islands of the Greater Antilles, and for reference purposes the Yucatan Penin- sula is included. At this point, observations made in Jamaica, Haiti, and the Dominican Republic are compared with reported information on Puerto Rico, the Bahamas, Cuba, the Cayman Islands, and the Yucatan Peninsula with regard to occurrence, as well as physical, chemical, and mineralogical composition. From this, an attempt is made at classifying the types of bauxites in the Caribbean, indicating the best reserves estimates, and the process ability of these bauxites. Some suggestions are also provided to fuel the controversy over the likely source material(s) or origin of the Caribbean bauxites.

Jan 1, 1984

By C. J. Bise

Continuous mining accounts for about 69% of the nation's underground coal production. This level is not expected to change much in the near future. This is because continuous mining represents the primary means of under- ground coal production. It is also the primary means of driving development entries for underground coal mines, including longwall mines. The continuous miner worksite contains many characteristics that can lead to personnel accidents. It continues to be an area of concern for mine managers, safety engineers, and training coordinators. In an effort to assist mine management in attempts to reduce the number of accidents and injuries sustained in this area, this paper presents a loss-control-based, non-intrusive strategy for conducting safety evaluations at continuous miner worksites.

Jan 1, 1991

By Joel K. Witt, Jackson G. Jenkins, Wendy M. Gort, Brent A. Whitman

A major concern for operators of leaching/SX-EW plants is a phenomenon known as gunk or crud. The build up of gunk is typically the result of fine particulates which are transported via the leach operation to the solvent extraction plant. The particulates develop into a solid layer that concentrates at the aqueous/organic interface. This can cause phase separation problems which can result in entrainment and other deleterious operating conditions. Most operations physically remove the gunk from the SX settlers and process it via a centrifuge or coalescer to remove valuable organic. While both methods have served for many years, Magma is currently evaluating the use of a chemical surfactant which induces a definitive separation of particulates from organic.

Jan 1, 1994

By F. -U. Schneider, F. Wellenkamp

Based on previous investigations of ultrafine comminution in planetary ball mills, a new centrifugal mill has been developed which permits similar high stress conditions. Because this new type of mill is equipped with an immobile chamber, devices for measuring energy, for cooling the milling vessel, as well as, in continuous operation, for material feed and discharge can be more easily attached than to planetary ball mills. Observations of particle behaviour have shown that, in the case of dry grinding, most of the material is found on the mill walls even after short grinding times. Due to the fact that energy dissipation takes place mainly in the zone near the wall, a grinding system which reduces the amount of ball filling required is at an advantage.

Jan 1, 1995

By Fang-tu Wei

The purpose of developing this system is to monitor the operating status of the fully mechanized mining system in order to raise it's reliability. The completely mechanized coal mining system is a complex dynamic system, involving many sub-systems. It is the key of the mining process as well as a connected system composed of each working procedure. Any hitch in breaking, loading or transporting will interrupt the mining process. The analyses of the operating data has proved that the reasons causing the interruption of the extracting processes mainly come from the inner of coal face. Hence, after the installation of the MINOS system in England, the delays of belt conveyor sub-system were reduced. But the production increment was not as much as expected.

Jan 1, 1986

By Todd R. Taubert, Kenneth L. Bickel

The U.S. Bureau of Mines (USBM) pioneered the development of disposable filters for reducing diesel particulate emissions from permissible mining machines. The USBM is now evaluating filter media that can withstand the high exhaust temperatures on nonpermissible machines. The goal of the evaluation is to find an inexpensive medium that can be cleaned or disposed of after use, and will reduce particulate emissions by 50 % or more. This report summarizes the results from screening tests of a lava rock and woven fiberglass filter media. The lava rock media exhibited low collection efficiencies, but with very low increases in exhaust back pressure. Preliminary results indicate a collection efficiency exceeding 80 % for the woven fiber media. Testing of both media is continuing.

Jan 1, 1995

By M. Stefanakis, A. Kontopoulpus, K. Adam

The application of Bacterial Oxidation as a pretreatment step for the extraction of gold from the Olympias refractory pyrite concentrate is described. A wide review of Bio-oxidation is presented focusing on the current process developments and commercial applications relevant to the treatment of gold bearing sulphide ores and concentrates. Preliminary batch and semi- continuous tests on the Olympas concentrate indicated that with Bacterial Oxidation quantitative gold liberation may be achieved. fie effect of such parameters as pH, Eh, temperature, particle size, operating pulp density and retention time on the extent of sulphur oxidation and subsequent gold extraction by conventional cyanidation are also examined. Finally, a preliminary evaluation of Bacterial Oxidation as a potential process alternative for the treatment of the Olympias concentrate is presented.

Jan 1, 1989

By J. A. Herbst, K. N. Han, P. B. Queneau, S. W. Asihene

As hydrometallurgy matures as a technology, more of its existing process knowledge will continue to be summarized in the form of detailed mathematical models. This development is happening at a time when major improvements in computer hardware have reduced the cost of computing. The opportunity then exists, through the solution of these process models, to design, control, and optimize hydrometallurgical plants on the basis of the physics and chemistry of its processes and less on empiricism. In this paper, a review of the current capabilities of sensors and phenomenological models for selected hydrometallurgical processes is presented. Future trends, in terms of the control and optimization of hydrometallurgical plants, are then explored. The possibility of simultaneously optimizing plant design and associated process control system performance is discussed.

Jan 1, 1993

By John S. Newton

Modern high capacity underground mining machinery is a complex of mechanical, electrical and hydraulic components which have greatly increased capability over similar components of mining machinery of ten and. even five years ago. Looking into the future I feel certain in stating that there will be changes equally great in the coming five and ten year periods. With this premise in mind, I should like to bring to your attention some of the things that do and will have a continued major impact on the industry, particularly as they relate to the maintenance and operation of these machines of increasing capability. In underground mining today, nearly every individual plays a key role. A machine operator's importance in his work is comparable with that of the pilot of an airplane, a railroad engineman, a bus driver, a skilled machinist, a bulldozer operator and many others whose assignment is one of doing, by himself, with his hands and his brains all that the specially designed machine has been created to do. These machine operators are supported by a staff of skilled engineers, maintenance personnel, supervision, etc., but objectives are realized only when the operator maintains his schedule. What is being done and what can be done to make it easier for the operator to maintain his schedule which, as with the airplane, is constantly being improved? This question can be answered best, perhaps, by dividing the subject into four general categories - (A) Power Supply. (B) Control and Protective Devices. (C) Hydraulic Component Design. (D) Mechanical Design.

Jan 1, 1962

By Neil J. Duncan, Edward R. Langfield

A hydraulic rock breaker was developed in Germany by Helmut Darda and uses a wedge-plug and feathers mechanism powered by a 10,000 p.s.i. power pack. During the past four years these tools have been increasingly used all over North America for secondary breaking of boulders and rock. More recently, techniques have been developed to break rock off the solid in trenches and rock emplacements where blasting is pro¬hibited or very limited. Underground operations are commencing to adopt the splitter for scaling plus including systems which can be efficiently applied to chambers and mines. Mr. Neil Duncan, who was originally scheduled to give the main part of this presentation has, during this past month accepted a position with the Alberta Energy Resources Conservation Board in Calgary. The board encourages its members to take part in seminars such as this but, unfortunately, due to the heavy pressure of work, it was impossible for him to attend this conference. Mr. Duncan has, however, forwarded me his notes and suggest¬ions, and using these, combined with a slide presentation, we feel that we can quickly and clearly define the operations and application of the hydraulic splitting technique as it applies to your profession and tunnelling work. The first question that most of you are asking is, "Why use a hydraulic splitter if you can blast?" Our answer to this is that we are not advocating the use of hydraulic splitting where blasting is feasible - but, during the past decade many applica¬tions have arisen where blasting is not allowed, or restricted

Jan 1, 1997