Search Documents

By H. C. Juvkam-Weld

R. Michael Craig Mr. Juvkam-Wold's article is a timely and much needed presentation of the method of depressurization to reduce ground-water inflow into mine shafts. The article is very informative and discusses the effects of depressurization upon shaft inflows adequately. However, the article omits a discussion of another important benefit of depressurization: the reduction of potential for artesian burst or, as it is also called, floor heave. Confined aquifer systems (artesian aquifers) can contain water under several hunder pounds per square inch (psi) of pressure. For example, water levels at elevations of 455 m (1500 ft) or more above the top of the Westwater Canyon member of Reply by H.C. Juvkam-Wold In general, Mr. Craig's comments are useful and accurate regarding the potential benefits of aquifer depressurization. However, two of his points require further explanation since they may lead to a misunderstanding of my paper and its predictions. These refer to his comments regarding failure to account for storativity and to non-artesian conditions. Equation 5 is indeed Darcy's steady state equation. However, as a careful review of the appendix in this paper will reveal, I have used this equation to represent semi-steady state conditions. In other words, steady state conditions are assumed at any instant of time, but conditions may change gradually from

Jan 2, 1983

By S. R. LaBrooy, M. C. Costello, A. C. Bax

Nickel is present in a number of gold ores in Australia, Africa and the United States. The effects and behaviour of the nickel during the cyanidation and adsorption processes, and also during the elution and electrowinning processes have been examined by a number of researchers, usually as a part of a larger investigation. This paper examines the available data on the behaviour and effect of nickel during cyanidation and its associated unit processes. The presence of nickel is often not considered to be particu­larly important as it does not cause the same degree of problems across the circuit as those experienced in the presence of copper. It can however lead to increased cyanide consumption during leaching, and reduced adsorption of gold onto carbon. A proportion of nickel cyanide may be removed from carbon prior to elution by carrying out a hot (90° C) acid wash. The nickel which remains on the carbon will be partially eluted during the main elution step, and, dependent on its concentration in the pregnant solution, part of it may be deposited during electrowinning. There is always a risk that any nickel remaining on the carbon after the elution step will be reduced to metallic nickel during the regeneration step. This may ultimately result in an increasing base level of nickel on the carbon, as metallic nickel is insoluble in both cyanide and hydrochloric acid.

Jan 1, 1995

By Terry M. Hertel

The chemistry of waters processed by Acid Rock Drainage water treatment plants can affect the Total Suspended Solids quality of the plant effluents. The sulfate ions in the ARD water will combine with the calcium ions from the lime that is used to adjust pH to form calcium sulfate. When the sulfate content of the waters to be treated is greater than about 1400 parts per mil­lion, the resulting calcium sulfate concentration will be approx­imately 2100 parts per million. This concentration is above the saturation point for calcium sulfate, and the salt will drop out of solution until the concentration falls below the saturation point. This "salting" phenomenon affects the total suspended solids of the treatment plant effluents by virtue of the fact that the salts will report to the filtration apparatus used for the analy­sis. This scenario is exacerbated as an effluent sample ages. Zortman Mining's water treatment plant effluent was being affected by "salting" during the spring and summer of 1995, and it seemed as though the effluents were exceeding the TSS lim­its; for no obvious reason. A testing program was initiated to verify an observation that "salting' was taking place. Treatment plant samples were collected and allowed to age, with TSS analyses being performed every day that the samples aged. Synthetic solutions were also prepared to study the "salting" phenomenon.

Jan 1, 1996

By Bruce Congleton

The Florida phosphate industry is a leader in environmental control, both in terms of dollars spent and significant achievements. For instance, since 1960 the phosphate industry has spent over $71 million for air pollution and control devices, including installation, research and development and maintenance. Water pollution control expenditures also total in the millions, with over $69 million spent in the same 10 year period. The industry also is a leader in water conservation measures, having spent nearly $ 18 million since 1966 for conservation devices. Since phosphate is mined by strip mining, land reclamation plays an important part in the environmental control picture. Here again, the phosphate industry has met the challenge with a voluntary program of reclamation which accounts for over 20,000 acres of land useable after mining has taken place. In terms of progress in environmental control, the industry has been able over the years to solve within the limits of technology the fluoride emission problems it once had, and is currently at work solving sulfur dioxide and particulate problems. In just the past year the industry also has been extremely successful in limiting phosphorus and nitrogen discharges into area streams. The industry continues to cooperate with state and local pollution control officials on matters of environmental control, and future plans include even closer cooperation and assistance, as well as increased expenditures.

Jan 1, 1972

By G. Ferrara, P. Bozzato, B. Chinè

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense-medium separation systems, the following two studies were made: a study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV) and a study of the behavior of suspensions of magnetite and ferrosilicon in water in both separators. It was found that the tangential velocity profiles differ in conical and cylindrical vessels. In a conical cyclone, free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e., that of a centrifuge. It was also found that the conical vessel manifests higher centrifigal acceleration and very strong densifying (the density differential) and, hence, the density gradient inside the vessel is large. It was found that the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e., low-density differentials, and hence, the density gradient inside the vessel is small. Also, due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while, in cylindrical vessels, the density cut- point is closer to the medium density. The results provide an interesting description of the differing behaviors of conical and cylindrical vessels, and they help explain the differences in pegormance between the two types of separators.

Jan 1, 2000

By Michael Chender

Introduction Clearly, many problems confront the minerals industry today. Yet, at the same time, there is too much energy spent bemoaning the negative effects of difficult economic circumstances, low metals prices, and adverse government policies. These are factors that cannot be altered by individual mineral company reactions. In fact, as we look to the future, the only thing we can be certain of is that we will continue to be faced with uncertainty. Thus, an area that demands close scrutiny and that can significantly affect a company's performance in the future is the posture it adopts to deal with uncertainty. This paper looks at how strategies are developing to deal with this issue. It also examines some of the implications that implementing such strategies have for the role of the individual explorationist. Elements of strategy Whether mineral company strategies are based on diversifying or retrenching, on emphasizing primary production or downstream integration, there seems to be increasing agreement that in the current environment strategies must have several features. They need to be information-based - developed out of access to timely and complete data and analysis about proposed directions and competitor activity, rather than simply following a current fashion. They need to be flexible - adaptable in light of changes in the marketplace and an unpredictable industry. And they need to be cost-efficient - making the most of limited resources. Whether a company is looking for gold financing opportunities, acquiring polymetallic prospects, or doing grassroots exploration for diamonds, these three elements are increasingly essential. They not only allow the company to pursue its current goals most expeditiously, but also open it to hearing and using feedback in the most constructive way. The company can then improve or change strategy as it proceeds. And it can be best positioned to take advantage of opportunities as they arise. These elements of strategy place great emphasis on the skills of the individual. The need for critical intelligence and the reduced amount of capital available to manage are making it more obvious that exploration is a "people" business. This is in accordance with a general trend in many sectors of industrialized economies, reflecting the widely discussed shift from smokestack to information-based industries. Increasing the odds There is a direct connection between successfully implementing the approaches to strategy discussed above and encouraging and improving the quality of work of the individual explorationist. To illustrate the importance of this, some commonly quoted figures on the odds of discovery success can be used. These figures are arbitrary but illustrative. Assume that one out of 100 exploration prospects actually turns out to be a promising ore body, and that one out of 1000 becomes a mine. Based on our research, chances are the most of those

Jan 1, 1986

By Alan English

This paper reviews the process control systems used in early commercial pelletizing plants, traces the development of these systems into present day practice, and briefly outlines advanced automation concepts being considered for future installations. It deals specifically with controls for the balling circuit, pelletizing machines, and related material handling and combustion equipment. The importance of instruments for visual observation and data logging is discussed, and the potential use of computer control is evaluated.

Jan 1, 1965

By Mark Newton Lowry

In the garden of national problems recognized by the American public, imports of mineral products is a hardy perennial. Concern for the security of mineral supplies has preoccupied nations since the industrial revolution and the mechanization of warfare. Since 1973, Americans have also been sensitized to the potential economic costs of overseas mineral supply disruptions and the cartelization of foreign production. Though oil prices have plunged since 1981, the import dependency issue remains topical. Political turmoil in Southern Africa reminds us that mineral supply disruptions will occur in the future as they have in the past. Producers of iron and steel, copper, and refined petroleum products seek protection from imports on national security grounds. The Reagan administration is proposing sweeping changes in the management of the federal mineral stockpiles. s an enduring need to take stock of the mineral trade position of the United States. This article considers the changing role that the U.S. has played in the twentieth century in non-fuel minerals trade. We begin by enunciating some principles that are useful in analyzing this trade. The changing pattern of trade in the 1900-1969 period is then reviewed. There follows a more detailed analysis of mineral trade trends in the 1970-84 period. Some consideration is given in the final section to the significance of non-fuel mineral trade for the U.S. economy. THE ECONOMICS OF U.S. MINERAL TRADE The allocation of non-fuel mineral products in the United States has in this century been accomplished primarily through the market mechanism. Except where trade barriers have distorted price signals, this means that mineral supplies have been obtained from the least cost source, with little regard for their country of origin. Mineral prices facing U.S. firms are sensitive to shifts in the domestic supply and demand, but are also sensitive to economic conditions overseas. The balance of trade in each mineral product has depended on the amount that is profitably produced and consumed domestically at the world price. The nation has produced exactly as much as it has consumed only by chance. U.S. demand for non-fuel minerals is derived from the demand for manufactures, farm commodities, and other goods whose production requires mineral products as inputs. The demand for such goods can be quite volatile, and in most industries moves cyclically due to its sensitivity to the level of aggregate economic activity. The supply of mineral products depends on the cost of extracting and processing mineral raw materials. These costs do not vary greatly in the short run. Because of these attributes of mineral markets, U. S. trade in mineral products fluctuates considerably from year to year. Most of this volatility results from shifts in domestic and overseas demand and from changes in exchange rates and trade barriers. Longer run changes in the mineral trade pattern can also be discerned. These depend on secular trends in demand and in the cost of mineral extraction and processing at home and overseas. The United States was originally endowed with extensive reserves of an array of mineral-rich ores and fossil fuels. It is also a nation with an entrepreneurial climate and technological capability conducive to extracting and processing those reserves. Not surprisingly, it has at one time or another ranked among the world's leading producers of a great many mineral products. With a population that is large and an economy that is technologically advanced by world standards, the U.S. has also been a leading consumer of mineral products. Because of its voracious appetite, the bulk of mineral products produced domestically has traditionally been consumed domestically as well. Net exports have been sizable only in those industries in which the nation has enjoyed an extraordinary cost advantage. Depletion has gradually reduced the cost advantage that the U.S. mining industry once enjoyed. The economic conditions that encouraged early development of U.S. mineral resources have

Jan 1, 1986

By Betty L. Gibbs, Jean A. Arcamone

Introduction Microcomputers are becoming more convenient to use at all levels in the business world, including the mining industry. The state of the mining industry requires that we become more productive and innovative in our analysis of deposits and operations. With the help of computers, examination of options to increase productivity can be performed quickly and inexpensively. Effective computer use to design underground workings combines the calculating power and speed of a computer with the technical expertise and judgment of an engineer. Computer programs can perform in minutes calculations that might take several months for an engineer. But the engineer must be on guard when using computers for calculations. It is easy to assume the results produced by a computer program are always correct. However, the computer is only a sophisticated calculator. It cannot recognize logical errors or transposition of numbers. Also, some intuitive or obvious decisions made by an engineer are difficult or impossible to program effectively. In this article, selected commercial programs are discussed. These programs can provide engineers with tools to evaluate engineering designs for underground mines. The programs perform much of the tedious calculation. The engineer, though, must still make decisions and conceptualize designs. The software mentioned in this article runs on microcomputers and minicomputers. The mention of particular software, however, does not imply endorsement. Mining projects After a decision has been made to proceed with an underground mining project, more detailed evaluation of the mining method and extraction sequence begins. If a mine is already in operation, schedules and plans are needed to more clearly define future production. Existing operations can benefit from identification of bottlenecks in material movement and produce extraction options to make the mine more efficient. Detailed studies for a new mine are based on the technical engineering design. These studies provide specific details to determine equipment requirements. Detailed studies done during a project are similar to short-term planning and control carried out daily by the mining engineers. The engineering design phase includes: • Study of the infrastructures - entries, shaft, access from surface to underground; • Definition of the mine layout, hydrogeology, geotechnical considerations, transport, and ventilation; • Choice of machines and equipment; • Mine scheduling, including waste extraction and production sequencing; and • Economics, including labor and supplies. Further detailed studies include: • Blasting patterns; • Detailed geotechnical calculations; • Secondary ventilation; and • Production cycles along with coordination of the workings. Objectives The primary objective of underground mine planning is moving material out of the mine at the least cost. Development of the production schedule considers location and volume of ore units, transport distance, equipment and manpower interactions, and grade or quality of material. Two methods can be used to determine the scheduled material removal: optimization or trial and error. The microcomputer programs discussed here do not cover optimization for underground mine planning. For several reasons, optimization is often a "black box" approach. Although optimization is possible with linear programming techniques, few mining operations can be described effectively with linear equations. An interactive trial-and-error approach is desirable because engineering judgment can be inserted as a plan develops. Because of the large number of factors in an underground operation, an optimization technique seldom covers all possibilities. Few of the programs available consider all of the possible parameters. The programs use an interactive sequencing or a simulation approach and are either event-oriented or deposit-oriented. The most desirable programs offer an integrated approach. They consider a broad range of operating conditions including equipment, labor, costs, material movement, timing, and mine layout, among other factors. The two types of models generally used in designing underground workings include: • The interactive model, which requires direct, incremental input from the user. Outlines of the section to be mined may show on the screen. The engineer causes the model to develop piece-by-piece. The program may offer feedback on parameters such as tons and grade, or other values, as the section is "mined." • The simulation model, which is usually an automatic technique. Parameters related to the process are entered. The program then calculates the mining sequence over a designated time period or until the economic material is exhausted. A simulation model imitates step-by-step performance of equipment or other processes.

Jan 3, 1988

By H. M. Conger

I'm really very pleased to be talking with you today about the environmental impacts of gold ore processing as part of this symposium on emerging process technologies for a cleaner environment. But before I talk about some of the newer developments that are coming, I would like to set the stage by reviewing some of the recent past. Over the last decade or so the U.S. gold mining industry has experienced remarkable growth, primarily in heap leaching operations, and not surprisingly there has been parallel growth of environmental regulations. At Homestake, we have had the excitement of bringing on-line a new mine embodying state-of-the-art technology and environmental planning, and during the same period the flagship of our company, the Homestake mine, has been brought into modern day compliance through the application of innovative environmental technology. This has been a learning process; in both cases we found that we had to develop new ways to meet our objectives. At our McLaughlin mine in California a major achievement was pioneering the use of pressure oxidation, or autoclaves, for refractory gold ores, and at the Homestake it was the development of a unique bio-treatment plant for wastewater. These projects were developed balancing operational goals, environmental concerns and costs, and I would submit that being cost-effective is our greatest challenge in the development of new, environmentally sound, process technology. In meeting that challenge, our job has not been made any easier by the myriad environmental laws and regulations that directly affect the design and operation of our facilities. Most of these constraints have evolved through the political process more or less independently, but in their application there often are over-lapping provisions. Adding to this complexity is the fact that action takes place in both state and federal arenas. As a result, state and federal roles sometimes become intertwined, and a good case in point is provided by various cyanide issues faced by gold producers. The vast majority of U.S. gold mining takes place in the so-called "mineral States," the western States that come under the Mining Law of 1872 as amended. This is the basic statute that provides for access and tenure to develop mineral resources on federal lands in those states. There is gold mining outside the defined mineral States, and there is also gold mining in the mineral States on private lands. Our own Homestake mine in South Dakota is one of the best examples of the latter category: located entirely on private land, it is nevertheless subject to at least 13 federal environmental statutes and some 29 federal regulatory requirements. There are also nine significant state statutory and regulatory requirements that apply. On federal lands in the mineral States there are numerous federal statutes and regulations which affect mining, over and above the current Mining Law. These, which are in addition to the laws applying to private land, include the National Environmental Protection Act and the Federal Land Policy and Management Act, among others. Still, those who advocate radical changes in the basic Mining Law would have us believe that sweeping environmental protection and reclamation provisions, not to mention new land use restrictions, are needed. Such changes could effectively prohibit mining on the federal public lands. Strict enforcement of our current Mining Law would have presented most of the abuses cited by the critics but if the Law is to be changed at all, I believe that, at a minimum, the principles of self-initiation and security of tenure embodied in the present statute should be maintained. These are critically important concepts, but there are other statutory and regulatory issues constantly before us as gold miners. Let me cite a few examples: Reauthorization of RCRA There are several bills being considered by Congress to amend the Resource Conservation and Recovery Act (RCRA) that have as their theme

Jan 1, 1992

By A. Russell, M. N. Hughes, Jack Barrett

The bacterial oxidation of arsenopyrite has been shown to be an efficient, economic and environmentally acceptable method for the liberation of any gold content . The mechanism of the process is not certain but is usually considered to involve direct and indirect reactions with respect to bacterial involvement. The direct reactions are those in which the bacteria attached to the mineral surface cause its dissolution, with dioxygen being the oxidant. The iron(III) produced in solution is the chemical oxidant in the so-called indirect reactions. Barrett et al 2 showed that a synthetic bio-oxidation solution (with no cells present) could dissolve up to 15% of an arsenopyrite sample, the products of the chemical oxidation being iron(II) and arsenic(III). This paper describes an extension of the investigation of the chemical process and its imp! ication for the mechanism of the bio-oxidation of arsenopyrite.

Jan 1, 1990

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risk associated with the design of mine waste management facilities. These experiences show that the technical and managerial challenge of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur to this day in both developed and developing countries is indeed remarkable, and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailing storage facilities are, in many cases, more demanding than those of conventional water dams, because seepage of fluids which contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 1999

By Betty L. Gibbs

The ultimate objective of mine design is to determine the development and untilization of mining resources. Computer Aided Design (CAD) and automated mapping are becoming very popular in engineering and in mining. Any computer program which produces a design or model with the interaction of an engineer can be considered computer-aided design (CAD), but' the term CAD is often associated with interactive graphic design and mapping capabilities. Graphics can be effectively used to describe and model two-or-three dimensional mine workings, orebodies, and geologic structures. Interactive computer graphics is applied to mine design with a combination of deposit modeling techniques and the use of AutoCAD for interactive graphics and mapping. The combined system can perform a large part of the calculations and drafting work for geologic and mining design. Using computer calculation and graphics techniques, comparisons of alternatives, can be made quickly.

Jan 1, 1989

By G. Capello

Carboniferous mining basins are today a non-negligible source of energy. So important in fact that returns now justify high investments and costs even for those deposits that were un-economical in the past. Nowadays, if properly explored and exploited, basins previously considered non-minable due to complex structural and stratigraphical situations may be economically interesting. It is while studying a faulted basin with such features that the Authors developed the described computer-aided methodology capable of constructing a model of the physical structure of coal deposits on the basis of stratigraphical data from drillings. The aim of the procedure is to define coal reserves, the exploitation of a deposit being conditioned by the possibility of identifying zones that are technically minable. This objective is pursued by making as detailed a reconstruction as possible of the geometrical, stratigraphical and tectonic features of the coal-bearing seams of a deposit.

Jan 1, 1982

By Hugh E. Cronin, John Ramage

The recommendations resulting from a Dispute Review Board (DRB) hearing of a contract dispute are being challenged more and more frequently. This paper explores possible causes based on the authors’ experiences. Challenges facing the DRB process include: The DRB process is starting to lose some of the informality and flexibility. Both owners and contractors appear to be putting too much weight on a board recommendation on a dispute. DRB’s do not make “decisions,” they provide recommendations for dispute resolution to both parties. The DRB process is not just for contractors to present an unresolved issue to a board hearing. Owners can also initiate a request for a hearing on a disputed issue. For the DRB process to remain a viable element of the successful construction project, confidence must continue to be maintained in a process that is intended to work on behalf of both parties to the construction contract.

Jan 1, 2003

By Graeme J. Jameson

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about one metre (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash-water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1988

By Terry Mudder

Long-term anaerobic biochemical treatment for draindown of residual solutions is a cost-effective way to close a heap-leach pad. This article presents a laboratory evaluation of anaerobic biochemical treatment of cyanide heap-leach pad solutions. The traditional approach to heap-leach pad closure is to rinse the pads with multiple pore volumes of fresh or recycled treated water. The effluent from an initial rinse is often treated and recirculated until the solutions passed through the heap meet the appropriate numeric and narrative water quality standards. Column rinsing tests are completed during project planning to determine the number of pore volumes of fresh or recycled treated water required to rinse the pad to meet long-term closure requirements. A traditional closure plan generally includes provisions to sample the rinse effluent and rinsed solids (the Meteoric Water Mobility, Procedure or USEPA 1312) to verify that chemical requirements are being met.

Jan 1, 1995

By Donald L. Bott

A computer model called the Quality Compliance Model was developed to optimize the mine planning and sequencing in area coal mining with respect to the limit on pounds of sulfur dioxide per million BTU imposed by regulations. The objective of the model is to maximize the amount of high sulfur coal mined from various benches while meeting the specified compl'ance standards. Given multiple seams and multiple benching operations, the mining sequence from each pit is simulated. The rate of mining is controlled such that the in-pit blending will maximize the usage of high sulfur coal and meet compliance standards. The compliant coal can be stockpiled for usage at a later date, or it can be disassociated. This calculation can be based on any given rate of production, i.e., from as small a unit as a unit train to as large as monthly or yearly production.

Jan 1, 1982

By Gary S. Brierley, Ronald E. Romley, Alan L. Howard

The Price Road Drain Tunnel in Tempe, Arizona is part of the drainage system constructed in conjunction with the Outer Loop Highway in metropolitan Phoenix. The Outer Loop Project is a part of a much larger expressway system that includes other large drainage tunnels such as the Papago Freeway Drain Tunnels. Large diameter downhole inspection borings were utilized to obtain subsurface data for the design of these tunnels. Subsurface data obtained from the large diameter borings resulted in the development of empirical parameters that were successfully incorporated into the Geotechnical Design Summary Report and which satisfactorily predicted ground behavior, formed the basis for improved geotechnical design criteria, and facilitated the cost effective assessment of third party risk. The purpose of this paper is to describe the subsurface exploration program performed for this project and to explain the methods used to evaluate underground construction procedures.

Jan 1, 1991

By Peter T. Luckie, Mark S. Klima

INTRODUCTION A physical separation partitions a stream of particles into two streams - one containing a concentration of a desirable constituent; the other containing a defficiency - on the basis of a difference in physical properties. Separating ores into concentrates of increased grade and gangue minerals has been practiced for thousands of years. Physical properties of materials which have been used to achieve separations include size, relative density, shape, magnetism, surface charge, color, characteristic emission, resilience and strength. The study of physical separations has also been termed attribute tracking. The term attribute is used to describe the content of the material of interest, or, sometimes, properties not used as a basis of the separation. The content is usually given by its assay; e.g., %Cu, %Fe, etc. Attribute tracking involves material balancing. For a separation using two physical properties, say x and y, the balance is

Jan 1, 1986