Search Documents

By D. T. Iseley, David Bennett, Christopher Norris

The microtunneling test program is one of three main elements of the research project, "Trenchless Construction: Evaluation of Methods and Materials to Install and Rehabilitate Underground Utilities." The other elements of this project include an evaluation and demonstration of horizontal directional drilling technology and pipeline rehabilitation systems. The research is a Corps and Industry cost-shared project funded under the Construction Productivity Advancement Research (CPAR) program. The laboratory partner is the U.S. Army Engineer Waterways Experiment Station (WES), Geotechnical Laboratory. The industry partner is the Louisiana Tech University's Trenchless Technology Center. Industry participants are contributing over half the total cost of this research. The overall objective of the CPAR program is to improve productivity in the U.S. construction industry, thereby enhancing the competitiveness of the U.S. industry in domestic and overseas markets. The Corps and other federal and state agencies will benefit by realizing reduced costs, enhanced safety and better products and services as the products of this research program are developed, tested, and pushed into the market place. The microtunneling demonstrations and evaluations were performed during September and October 1992 at a specially constructed test facility built at WES in Vicksburg, MS. The test facility is 104 m (340-ft) long, 5 m (16-ft) wide, and 4 m (13-ft) deep. It was constructed, ironically, by first excavating a trench into which 6 different types of soils were placed and compacted in approximately 18.3 m (60-ft) long sections. The soil profiles include a lean silty clay (loess), a dry sand, highly plastic buckshot clay, wet sand, clay gravel and silt. The interfaces between soil profiles were sloped to simulate mixed face conditions as the machines exit one zone and enter another, and provided challenges to ground control and alignment and grade control during these transitions. Moisture and density tests were performed on all materials in each lift to assure uniformity. Horizontal inclinometers and 3 levels of settlement plates were installed at key locations in the test bed. The settlement plates and rods and the horizontal inclinometers, together with surface survey points, provided data to evaluate settlement and heave along the test section. Penetration resistance was measured in each section of the completed test bed. Strain gages were installed in 8 of the 0.6 m (24 in.) diam. Hobas pipe sections to measure strains in the pipe as it was being jacked into place. Steering jack loads, jacking thrust loads, and cutterhead torque were also measured during the drives. The results of these tests will be used together with other information to develop guidelines for conducting feasibility studies and selecting proper methods compatible with anticipated conditions.

Jan 1, 1993

By Matthew E. Eisenmann, Gerald H. Luttrell

Performance data from phosphate plants are often untrustworthy because of difficulties associated with highly variable feeds and unstable equipment operation. In some cases, this problem is further compounded by improper sampling procedures and unreliable laboratory analyses. Questionable data often lead to misleading conclusions that result in lost productivity and profits. Data reliability may be checked using mass balances, but the mathematics associated with this procedure can be overwhelming when multiple data sets or complex circuits are evaluated. To overcome this problem, a simple spreadsheet-based mass balance program has been developed specifically for plant operators. To use this program, operators simply enter a description of their circuit and input the assay values (e.g., % BPL, % Insol, etc.) for each stream. The program then generates the best estimates of the assay values and flags values that may be unreliable. The spreadsheet is specifically designed to be easy to use and requires no knowledge of statistics or programming. This manuscript reviews the mass balance problem and describes how spreadsheet programs can be used to evaluate plant data. An example problem involving the analysis of data around a two-stage phosphate flotation circuit is presented.

Jan 1, 2002

By E. A. Metz

It has been approximately four years since the International Agency for Research on Cancer (IARC) reclassified crystalline silica as a "group one" substance. Since then, crystalline silica has been considered a human carcinogen. Silicosis is a preventable disease, and several aggressive campaigns have been developed to increase awareness of silica-dust-related problems in the industrial environment. New analytical techniques are now being developed to determine quantitatively the amount of crystalline silica in materials. Yet, still much is to be learned about the surface properties of silica and the way in which the disease progresses into full-blown silicosis. This paper discusses the interaction of free radicals generated by the mineral particles and lung tissue. It is the cell injury and DNA damage that progresses to fibrogenesis. Freshly fractured surfaces of silica contain free radicals. These free radicals play an important role in the stimulation of the alveolar macrophage and the development of the inflammatory reactions leading to the fibrotic response caused by silica. Engineers, scientists and physicians need to discuss the mineralogy of silica and the technical issues concerning the development of silicosis.

Jan 1, 2000

By J. E. Osmanski

This semantically ambiguous title purports to describe an examination of the question of automation and its effect on the industrial worker. More explicit titles might be "Painless Automation" or "Mechanization without a Sting" or, if I may steal a few phrases from the title of a recent interview Pith John L. Lewis, "More Machines, Fewer Men -- Is the Union Happy About It?" Automation has become the biggest ?scare word? for many industrial workers and their unions since "wage stabilization.? "To many a union orator," reports TIME of January 4, "automation is the sinister business of eliminating jobs." TIME might better have phrased this description by saying that many unions regard automation as the attempt to eliminate not jobs, but workers, The recent steel dispute was hung up for so long primarily because of the problems evolved of increased job efficiency through automation and job changes. Everywhere today there is heard the cry of our need for maintaining full employment within the context of an expanding economy echoing against the sheer reality of automation's displacement of thousands of workers through a rapid acceleration of productivity.

Jan 1, 1960

By S. K. Mishra, R. L. Lytton, D. Sinn, D. Saylak

Calcium chloride is widely used for dust control on unpaved roadway surfaces, in base course stabilization, full depth reclamation and for total reconstruction of asphalt roads. Fly ash produced from coal-burning electric power plants have also been used in road construction. This paper examines the synergistic effect of calcium chloride and fly ash on compaction density and strength development of unpaved roadways. A mathematical model has been developed which provides excellent agreement with the experimental data. Based on these results, the potential of calcium chloride - fly ash treatments for typical mine road construction is discussed.

Jan 1, 2004

By Peter J. Borchardt, Helen M. K. Andersson, Donald A. Bruce

Grouting is a useful engineering tool for tunnels throughout the world. A wide variety of methods and materials are used, reflecting the broad range of geological, hydrogeological, and structural demands. Most tunnel grouting is conducted with cement, which produces acceptable results in appropriate conditions. However, there are cases where such grouts are not practical, but polyurethane grouts can be extremely useful. Regretfully, these grouts are frequently poorly understood, leading to improper application and therefore poor results. This paper provides a fundamental overview of their application, both used individually and in combination with cement. Case histories from Scandinavian practice are cited.

Jan 1, 2001

By Liang Ruilu, Guo Lihua

In light of the properties on process mineralogy of the old tailings in a certain copper mine in the People's Republic of China, a new process of combined reagent and stepwise flotation is applied in which the flotation of copper sulfides is followed by the flotation of copper oxides. Recoveries of copper and associated gold and silver have been greatly increased. The tailings obtained were subjected to the gravitational separation-magnetic separation process to recover iron minerals. Tailings from iron separation are taken as fillers and sent to the pit underground. Thus, the secondary resources are comprehensively utilized.

Jan 1, 1995

By R. P. King, S. Middlemiss

A method is developed to convert a measured distribution of fracture energies to the equivalent work index. The method assumes that the energy required to grind the material from the feed size distribution to the product size distribution is equivalent to the sum of the impact energies that are required to reduce the feed material by successive single impacts to the required product size. The method was tested by measuring the fracture energy distributions for quartz and comparing the resulting calculated value of the work index with the work index for this material measured using the conventional Bond laboratory procedure.

Jan 1, 1998

By P. Zhang

The Crago “Double Float” process is widely used in upgrading phosphate ore. This process is inefficient, as it floats about 30-40% of the sands in the flotation feed twice and requires a deoiling step. This paper summarizes several research projects on improving phosphate flotation. The University of Utah investigated a new flotation chemistry for efficient flotation of phosphate in a single step. The Florida Institute of Phosphate Research developed several single-collector, all-anionic flotation flowsheets using various sizing schemes. In addition, Eriez invented the HydroFloat separator, which demonstrated great potential for processing coarse flotation feed in one step.

Jan 1, 2004

By P. W. Johnson, H. Fan, S. B. Patton, T. Novak, R. L. Sanford

A computer model is presented that quantitatively uses the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasitication on the ventilation system in a longwall panel.

Jan 1, 1995

By Y. Topkaya, R. E. Johnson, B. R. Palmer, Jia-Jun Ke, Da-Ping Kang

The kinetics of the leaching of antimony oxide ore (Sb2O4) in aqueous hydrochloric acid solutions has been investigated. This dissolution reaction is a heterogeneous solid-liquid reaction. It has been found that the leaching temperature and the concentration of hydrochloric acid turn out to be the significant influencing factors on the leaching rate. The apparent activation energy for the leaching reaction was determined to be 63.5 W/mol within the experimental temperature region of 50O to 90O C. The experimental results indicate that the leaching process is controlled by the rate of the chemical reaction.

Jan 1, 1993

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By P. Lausch, R. A. Mercer, J. F. Archibald

An innovative, polyurethane-based, spray on rock-lining material, designated Mineguard™ by its developers, is being manufactured to provide rapidly deployable area support coverage for specific use in underground hardrock mines. This form of surface-coating agent is intended to replace both shotcrete and the screen component of bolt-and-screen support systems. Due to the rapid rate of application, ease of installation and ability to achieve a 90% cure within seconds of application, Mineguard™ has considerable potential for use in mining and excavation operations that require a rapid rate of advance and a high degree of automation.

Jan 1, 1996

By D. Papacharalampos

A combination of decision- theoretic and knowledge-based methods can be used to classify rock-types from satellite data both efficiently and accurately. An expert system utilizes knowledge-based rules, as a field geologist does, to produce results that make geological sense. Our expert system (GEMS), first processes background information from preexisting knowledge and develops a plan, then classifies individual pixels, and finally generalizes the results using geological rules and plots a map. The system is implemented on a microcomputer and is inexpensive enough to be a part of the standard equipment of any geologist who prepares reconnaissance maps.

Jan 1, 1986

By I. González, G. Lapidus, M. Teutli

The cementation kinetics of silver with aluminum particles were studied with model solutions under nitrogen atmosphere, varying the temperature, aluminum/silver ratio, pH and concentrations of thiourea and surface activator Recoveries were evaluated both by solution concentrations and by REDOX measurements. Tafel curves were determined for this system. The results showed the cementation process to be essentially independent of the pH and thiourea concentration. However, a strong influence was observed with respect to temperature, aluminum/silver ratio and the quantity of activator. There is evidence that the controlling step is the dissolution of aluminum oxide from the particle surface.

Jan 1, 1990

By M. E. Kuchta

Research is currently being conducted at the Colorado School of Mines in the use of high-pressure water for scaling down loose rocks in underground mine openings. In addition to improved miner safety, the adhesion strength of shotcrete applied to rock surfaces treated with high-pressure water is also increased significantly, resulting in improved overall support capabilities of the shotcrete layer. Test results show an increase in adhesion strength by a factor of four on a concrete test wall cleaned with water at 21 MPa (3,000 psi) as compared to a surface cleaned at 0.7 MPa (100 psi).

Jan 1, 2003

By Regina N. Tempel, Laurie S. Balistrieri, Lisa L. Stillings, Maggy F. Lengke

The Dexter pit lake, within the Tuscarora volcanic field in Elko County, Nevada, formed after closure of the Dexter mine. Mineralogy at the Dexter mine is related to widespread feldspar, silica, and chlorite alteration. Major mineralogy includes quartz, alkali feldspar, albite, phlogopite-biotite, hornblende, iron-titanium oxide, chlorite, kaolinite, smectite, illite, and sericite, with lesser amounts of calcite, zircon, apatite, and rutile. Trace element geochemistry is characterized by high levels of As, Ba. Cr, Cu, V, Zn, B, Zr, Li, and U. Detailed mineralogy and geochemistry are required for geochemical models to accurately predict trace element concentrations in pit lake waters.

Jan 1, 2000

By K. Professor Heiskanen

The improvement of grinding circuit efficiency is a constant industrial requirement. It has often been connected to the improvement of classification. The paper discusses some operational aspects of hydrocyclone classification. A hydrocyclone should be operated close to roping but should not with high density slurries go to roping. Unfortunately roping is not well understood and roping models for controlling hydrocyclone operation are not adequate. The paper discusses also some ways of improving the classification in terms of bypass and imperfection. The last part of the paper discusses the effect of bypass and imperfection on circuit performance.

Jan 1, 1997

By Emil O. Frind, David W. Blowes, K. Ulrich Mayer

The multicomponent reactive transport model MIN3P can be used to simulate the evolution of pore water, pore gas, and the mineralogical composition in mine waste environments. The model is formulated for variably-saturated conditions, considers transport of dissolved and gaseous species, and describes geochemical reactions based on a partial equilibrium formulation. Reaction processes included are complexation, oxidation-reduction, ion-exchange, mineral dissolution-precipitation and gas exsolution- dissolution reactions. An example application, describing the generation of acid mine drainage and subsequent reactive transport for a ID-vertical profile in a tailings impoundment near Elliot Lake, Ontario, is provided.

Jan 1, 2000

By Leonard Harris, Rosa H. Harris

An important part of doing business today in the mining industry, especially overseas, involves community assistance programs for the people who live around the mining areas. The purpose of such a program is to build mutual cooperation and respect that will allow the company and its neighbors to live and work in peace. To do this, it is necessary to form associations or foundations and work in a joint venture fashion. The authors discuss in some detail the outline for setting up such programs and the important role that women, in particular, can play in them.

Jan 1, 2001