Search Documents

By Anshumali Gangwar

This paper outlines the chance constrained binary integer program developed by the author in his doctoral dissertation at Columbia University, New York, 1973. The optimum planning of a mining program involves the determination of a production schedule which maximizes the net present value of the mining property. The actual mining process has an inherent stochastic and discrete nature. In particular, the demand for the mined product and the grade of the mineralized material in the ore are the two most important stochastic mining variables. The decision to mine or not to mine any block of a mining property is a binary integer variable. This paper outlines the formulation of pit production scheduling problem as a chance constrained binary integer program. The deterministic equivalents of these chance constraints are nonlinear in binary variables which have subsequently been linearized. The planned objective is to meet with a stipulated high degree of reliability, all the random demands as they materialize with a random supply of the commodity being marketed as determined by the eventuating random grade values of the exposed ore blocks and the mining system's production constraints such that the discounted total production costs over the entire planning horizon are minimized or the profits maximized. The emerging surface of the mine in each scheduling period is determined by the values taken by the binary decision variable associated with each block of material in each scheduling period.

Jan 1, 1982

By E. J. Beckman, R. M. Enick, C. Shi

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. Two inexpensive and environmentally benign fluids were selected for the study, water and carbon dioxide. The separation, which is conducted at 295 K and at the vapor pressure of carbon dioxide (6.0 MPa), is based on differences in wettability between the precious metals and other minerals. Contact-angle results indicated that, in the presence of water and liquid CO2, gold is slightly hydrophobic. The addition of CO2-soluble fluoroalkyl thiols or f uoroetherthiols increased the hydrophobicity of gold exposed to water and CO2 to a greater extent than alkylthiols. Minerals, including quartz, pyrite and magnetite, were hydrophilic. During the separation, an aqueous slurry of fine mineral and gold particles was mixed with liquid carbon dioxide. Pure gold particles (-325 mesh) were found to agglomerate at the H2O-CO2 interface. The minerals tended to remain in the aqueous phase. Despite these promising preliminary results, very poor gold recoveries were obtained when applying the procedure to an Australian gravity concentrate. This was attributed to the native gold particles in the concentrate being either too large, agglomerated in slimes or coated with minerals. Although this particular application was unsuccessful, this water-CO2 biphase technique may be applicable for other separations that require the removal of very fine, hydrophobic particles from an aqueous slurry.

Jan 1, 2000

By M. Z. Rashad, H. A. El-Sageer

This paper compares the covariance and multiquadric functions in some mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 km2 x 16 km2 area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of 48 test stations were computed by using the data of 63 control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function is simpler in computation than the covariance, which requires precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometric and physical considerations rather than covariance functions.

Jan 1, 1992

By Gary Schaffer, Anthony Stentz

Surveying of mines is a necessary step in coal mining to assemble maps which are used for tracking progress in the development of the mine and to plan future coal removal. A first approach for automatically building high-resolution two-dimensioml maps of underground coal mines is presented. The technique assembles laser rangefinder scans obtained from several locations within the mine into a consistent global map of the mine. Each range scan comprises thousands of data points collected in one second, thereby achieving higher resolution and much faster measurement compared to a human using a transit. The raw data (range scans) are processed to fuse them into a consistent representation. This paper describes a first approach to automated surveying and presents initial results of merging range scans. Improvements to the scan-merging algorithm are proposed.

Jan 1, 1993

By Welland L. Ott, Hans J. Rumland

The Falconbridge Dominicana laboratory receives samples from all parts of the operation. Ore, metal and oil samples are taken by operating departments, gas and water samples by the laboratory staff. Physical sample preparation is essentially standard and produces comminuted samples for wet-chemical analysis and X-ray fluorescence analysis (XRF). T he main operating sections of the laboratory are described indicating in each case the type of instrumentation and method used, sample types analysed and comments on problems experienced. Emphasis is given to the sample preparation and X-ray sections especially with regard to the difficulties caused by our heterogenous ore material, calibration of the instrument and operational malfunctions. General problems related to our remote location and the tropical climate are discussed. Limited statistics on instrument availability, and stability, accuracy, precision, etc., are given.

Jan 1, 1979

By R. J. Wesely, Corby G. Anderson, L. Ernest Krys, John B. Ackerman, A. D. Zunkel, Suzzann M. Nordwick

Processing of the refractory precious metal ore from the Sunshine Mine is done in a fully integrated hydrometallurgical facility. This operating philosophy began with the construction of an antimony plant during World War 11, and it continued with the construction of a silver-copper refinery in 1984. The antimony plant relies on an alkaline sulfide ambient pressure leach combined with antimony electrowinning and antimony compound production. This plant is the largest producer of antimony metal in the United States. The one-of-a-kind silver- copper refinery uses a nitrogen species catalyzed sulfuric acid pressure leach system. The plant contains innovative downstream silver recovery processes as well as copper solvent extraction and electrowinning. This paper presents the pertinent process chemistries and flow sheets for the two unique hydrometallurgical processing plants.

Jan 1, 1993

By C. D. Anderson

"IntroductionTungsten carbide is a valuable material used in a variety of different applications, including the manufacturing of cutting tools, bearings and as a cost-efficient alternative to industrial diamonds. Both the high hardness value (Mohs 9) and scratch resistance of this material make it a valuable commodity for use in the mining industry.Usually, the production of tungsten carbide is a multistep process involving one or more of the following unit operations: hydrometallurgical digestion, solution purification, crystallization (as ammonium paratungstate), calcination, hydrogen reduction and carbon synthesis. The proposed three-step process eliminates three of these steps (crystallization, calcination and hydrogen reduction) by implementing a combination of hydro/pyrometallurgical techniques. These include alkaline pressure leaching, carbon adsorption and carburization roasting. By eliminating some of the intermediate processing steps, there is potential to reduce energy consumption and decrease overall operating costs.Methods and resultsInitially, alkaline pressure leaching with sodium carbonate (Na2CO3) was employed to selectively leach tungsten, as tungstate (WO4 2-), from an industrial Scheelite (CaWO4) flotation concentrate. Experimental variables included lixiviant (Na2CO3) concentration, temperature and residence time. Experimental constants, based on previous work, were percent solids at 13 wt% and agitation at 400 rpm (Queneau and Strathmore, 1969). Leaching results showed it was possible to extract 97% of the tungsten present. The most favorable conditions for leaching were determined: 2M Na2CO3, temperature of 180° C and a residence time of 30 minutes."

Jan 1, 2015

By E. E. Jones

The lignites of Arkansas, Louisiana and Texas are typically described as muitiseam deposits which contain quantities of day and sand in thin lenses or in admixture with the fuel itself. These materials are often included in the run-of-mine fuel and can have very adverse effects in the end use. Since May of 1982 the Dow Chemical Co. has operated a pilot plant for the beneficiation of lignites. This facility has successfully removed sand, clays and petrified wood from the lignite producing a fuel comparable to or better than the selectively harvested run-of-mine materials. The design, operation and results from this plant were presented by J. H. Everitt at the 1984 Coal Technology Conference.

Jan 1, 1986

By S. Vijayan

Despite the limited demand for rare-earth elements, as well as yttrium and scandium, in conventional applications, the emergence of ne~ high-technology applications such as supermagnets, lasers and superconductors is expected to result in significant demand for some of these elements. This paper examines the anticipated applications and demands for rare-earth elements over the next decade and their implications on the utilization of available resources. Process methods for the recovery of rare-earth elements from conventional and unconventional resources are reviewed in the context of their growing demand. Challenges facing the industries in meeting this opportunity are also discussed.

Jan 1, 1988

By R. K. Rajamani

The theoretical model based on fluid mechanics, in conjunction with the laser-Doppler velocimetry (LDV) measurements, elucidate the size-classification mechanisms in an industrial hydrocyclone. The model has no adjustable parameters and involves solving the Navier-Stokes equations to predict the liquid-phase velocities. The spatial-concentration gradients were determined considering the particle phase in the Lagrangian frame and the classification curve was determined by balancing the forces acting on the particle. The force balance requires liquid velocities, which in turn depend on the local volumetric concentration of the particles. Hence, complete modeling work involves coupling both the concentration and liquid-phase velocity calculations until convergence is reached. Finally, the experimental and predicted classification curves were presented for 250-mm hydrocyclone operating at high-percent solids.

Jan 1, 1994

By Marvin Barnes

The Sacaton mine is a relatively new open¬pit copper mine owned by Asarco, Inc., which has been in production only a few years. The mineral deposits consist of two ore zones; a western, near-surface zone minable by open-pit methods, and a deeper eastern zone which will have to be mined underground, probably by block caving. The copper deposits are related to small quartz monzonite intrusives implaced into Precambrian granites. Both rock types act as hosts for the copper mineralization, which has been secondarily enriched sufficiently to constitute ore. In the western zone the enriched supergene chalcocite has been subjected to postenrichment oxidation processes with partial destruction of the chalcocite blanket. The deeper eastern chalcocite zone has not been as severely affected by later supergene processes. Several mineralogical populations are represented in the total copper deposit. Leached capping overlies the chalcocite enriched zone, and in the western ore body there is a very irregular interface between the leached and enriched zone, which is complicated by oxide copper minerals irregularly distributed. Primary lower-grade chalcopyrite mineralization occurs below the enriched zone. When mining commenced near the top of the enriched zone, considerable difficulty was encountered in correlating the actual grade of ore in place with the estimated grade of the mining blocks. The mineralogical complexity and fairly wide spacing of diamond drilling made reliable grade estimation of individual ore blocks a difficult procedure.

Jan 1, 1979

By Patricia T. Foley

An analysis of the demand for copper shows a widely varying pattern of end use. For example, copper tube is the most popular material for hot water supply in the US and northern Europe, but galvanized steel is used in Japan and plastics are used in developing countries. In addition to such peculiarities of end use, the demand for copper varies among countries depending on the stage of industrialization and the extent that the copper processing industries are developed. Brazil, with its abundant supplies of bauxite and hydroelectric power, uses aluminun in place of copper wherever possible. South Korea, with its export oriented economy and its advanced custom smelting and fabricating industries, favors copper. Understanding the details of demand in different countries enhances statistical derived forecasts and illustrates potential new markets.

Jan 1, 1986

By M. Ericsson

The extractive industries consist of five major sectors: - Mining equipment and services - Dimensional stone - Industrial minerals - Aggregates - Metal mining These industries produce some finished goods but mostly semi-finished products as they feed into other industrial sectors: Basic metals, fabricated metals, construction, chemicals, dyes and pigments, inorganic chemicals, fertilizers, rubber and plastics and non-metallic mineral products. These are the major down-stream industries in this study. Taken together with the extractive industries they form the mineral resource based cluster. The mineral resource based cluster is a substantial part of the Finnish economy: It employs 211 000 persons, 39% of the number of employees in industry. The cluster?s exports account for 20% of industry exports. Value added is 34% of total value added in industry. Investments reach 35% of total industry investments.

Jan 1, 2003

By Stanislaw Wasolewski

Computerized systems for ventilation parameters monitoring which are used in Polish coal mines provide the ventilation staff with a great number of measuring data. These data can be used to get knowledge about dynamic properties of ventilation process and disturbances affecting its state. This is necessary to create a reasonable concept of mine ventilation control system and make a practical application of such system. In the paper a method of ventilation process identification with the use of measuring data from monitoring system is described. Computer analysis of time series including statistical, correlation and frequency methods are applied to estimate dynamic properties of ventilation process and its disturbances. Using the Fast Fourier Transformation (FFT) algorithm the parameters of the process have been obtained which can be efectively used in a system for mine ventilation control.

Jan 1, 1991

By S. N. Mukherjee

Maintenance of equipment in Longwall faces plays a vital role in face performance. This is more prominent when shortage of spare parts and trained personnel occurs. A study was made in an operating Indian Longwall face for identifying the types and meantime between failures. Though the duration was not enough and study was not very elaborate, it revealed certain interesting facts. The machine availability was found to be poor, though a maintenance schedule was followed. Failure of simple parts like AFC chain connectors even resulted in loss of production of 10 times the complete chain cost. This pinpoints that a proper maintenance schedule is to be developed considering the human factors and local conditions existing in the particular country. Operations research techniques could be used in the process.

Jan 1, 1989

By Z. Nivolianitou

This article aims at highlighting the importance of technological innovation, namely the potential use of Virtual Reality (VR) technology, as a Sustainable Development Indicator for the minerals industry. Nowadays, VR is regarded as a mature technology for real world representation, and it has been already applied in various domains such as architecture, topography, aeronautics, medicine, and lately in the process industry. Several industrial sectors already use VR tools, as the car industry for improving car ergonomics and design and the aviation industry for both pilot and maintenance crew training. It is well known that the mining industry, as well as the process industry, requires people to work in hazardous environments and situations, often inadequately trained owing to limitations in time and resources, building thus the potential for minor or major accidents.

Jan 1, 2007

By M. Jaramillo

The expanded west pit of the 15 Mta (13.6 stpy) El Cerrejon mine will eventually reach a maximum depth of 270 m (890 ft). Slope-stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization calls for anchoring the footwall by the installation of 9- to 33-m- (30- to 108 ft-) long multistrand steel cable bolts. For each of the 15-m- (50-ft-) high mining benches, a row of bolts is installed with variable horizontal spacing, depending on the dip magnitude. Cable bolting is now standard operating practice, and an estimated 11,800 bolts will be installed during the life of the mine. Results to date have been satisfactory in terms of the stability condition of the bolted slopes.

Jan 1, 1997

By Roberto Zaragoza

Historically, the control of flotation operations has been viewed by many as an art. Only recently has process measurement and control come to be viewed not as an ?art? but as a very complex and productive science. In recent years, process control applications to flotation plants have been established and already some gains have been reported for several industrial operations using individual stabilizing control loops including level, pulp flow, pulp density, reagent addition rate and pH (Paakinen, 1979; Hales, 1985). The use of process control computers combined with on-line x-ray florescence (XRF) in industrial flotation circuits has made the application of more sophisticated control techniques feasible in the mineral recovery process. In spite of the availability of reliable instrumentation in modern flotation plants, satisfactory control strategies are difficult to develop and implement. Extremely important factors such as changes in ore type, liberation characteristics, flotability, degree of oxidation on particle surfaces, and specific gravity constitute unmeasured disturbances to the process. Most current control systems cannot adapt specifically to such disturbances.

Jan 1, 1987

By A. R. Zambrano

Equations for power draft, capacity and work input for predicting the performance of industrial grinding mills are derived based on torque measurements using a laboratory instrumented mill. These derivations are based on mechanical principles and on the first-order kinetics of the grinding process. Rittinger's, Kick's and Bond's laws express work input as work index (Wi) times a particle size function. It is proposed that these laws are only particular cases of more general expressions having the particle size function raised to an exponent, i.e., the work exponent (We). Case studies illustrate the excellent prediction of the Wi - We models compared to the three mentioned laws, and, from the data, the corresponding general mill-sizing equation is derived. Key words: Grinding mills, Comminution, Work index, Mill sizing

Jan 1, 2003

By William H. Schiffbauer

Research is being conducted toward making underground mining equipment autonomous. This will facilitate improvements in safety by relieving workers of dangerous tasks and will increase production by providing more accurate control with less down time.. A Bureau of Mines developed microcomputer network has enhanced this research by permitting a group of diverse computers to interact with a mining machine as well as with each other over a common data link. The network is composed of specially integrated off-the-shelf hardware and industry-standard operating system and programming languages. Using the network, researchers can conduct various experiments with the mining machine using a diverse group of intelligent sensors, computers, and microcontrollers. Descriptions of the mining machine, the mining machine control computer, control algorithms, -the microcomputer network architecture, and communication protocols are discussed.

Jan 1, 1989