Search Documents

By S. Slottee

The disposal of plant tailings in a safe and environmentally acceptable manner has taken on increased importance throughout the world, across all types of mineral beneficiation plants. In the U.S. plant life span, expansions and new plants in the current robust mineral markets are faced with environmental pressures to minimize the use of land for disposal by maximizing existing tailings pond capacity. The combination of many drivers from economic to environmental have brought paste thickeners into the coal industry (PasteThick 2007) Thickening tailings to a more concentrated slurry is a common step in the disposal flow sheet. Thickening to a non-settling ?paste?, also called ?thickened tails? or ?tailings stacking?, is a relatively recent development. This paper describes the paste thickener as an alternative for dewatering a fine coal refuse (tailings) stream for deposit as a paste. Initial operating results of the paste thickener are discussed.

Jan 1, 2008

By P. Maraboutis

Extractive industry (mining and quarrying operations), as other industrial activities, is subject to environment protection laws, regulation and standards such as the Environmental Impact Assessment directive, Natura 2000, Habitats & Birds directive, Water Framework directive etc The European Commission (EC) is aim to strengthen the EU environmental legislation to improve the (environmental and human) safety of mining activities. The mineral processing and the management of the mining waste will be covered by the new amendment of the Seveso II Directive, by a Best Available Techniques reference document (BREF) describing the Best Available Techniques of mining waste management and a new directive on the mining waste management. At the same time initiatives as the environmental liability, the energy taxation for environmental reasons and the natural resources management policy, which will have a positive impact on the protection of the environment, will affect the extractive industry operation procedures.

Jan 1, 2002

By Manuel Diaz del Rio

At the present time there are over 5,000 Kms of railway tunnels in existence throughout the world. In many cases these tunnels were built over a century ago using techniques obsolete today. Supervision and maintenance of these tunnels is essential to the economy of each country involved. For this purpose an electro-optical measuring system has been designed incorporating highly complex soft and hardware (15 mW laser, high resolution TV camera and processing computer), mounted on a vehicle. Its job is to scan, record and compare sectional gauge values (profiles) and strains inside tunnels both momentarily in situ and on permanent record, as an aid to the supervision work. From the state of the strains observed, in conjunction with an infrared spectrum of the tunnel lining and soil involved, the mechanical stresses in the tunnel can be deduced by applying the boundary elements method.

Jan 1, 1981

By Edward DeLilla

Formalized technical audits for mining machinery during manufacturing are a fairly new concept to the North American mining industry. Although used extensively elsewhere, especially in Australia, the concept of independent auditing of machinery design and manufacturing has been slow to gain acceptance in the United States and Canada. Simply stated, a technical audit is an independent, third-party review of all or specific portions of machinery design, manufacturing and assembly to verify compliance with purchase specifications and suitability of the machinery for the specified application. If specified correctly, the useful life of different kinds of structural and mechanical components can be extended beyond normally accepted usage. There is no reason why, if properly designed and built for the application, major structural components on mining machinery cannot be made to last for 20 years before being rebuilt. Also, gearing can be made to routinely last for 15 years.

Jan 1, 1995

By H. Lyn Bourne

The is the 13th year for this column and the 12th in which the royalty data have been tabulated. There still exist some holes in the list of royalties that readers hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. In spite of their pervasive use nationwide, there are states from which the author has no information about royalties for either of these commodities. The reader can help - share information about these missing states and next year there will be fewer states without information. Severn Brown again sends helpful information from the Prospectors and Developers Association of Canada (PDAC). The PDAC Digest contained an article that distinguished between ‘net smelter return royalty' and ‘net profits royalty’ (Haase). The article also lists clauses and details that Brown suggests should be included in a net profits royalty contract.

Jan 1, 1994

By Cherie M. Tilley

The Stillwater Mining Company has acquired a Tunnel Boring Machine to expedite the mine development operations at its Stillwater Mine. The machine purchased by Stillwater was previously owned by Melbourne Metropolitan Board of Works, Melbourne, Australia. The machine was manufactured by Robbins Co. of Kent, Washington. The Stillwater Mine has an extensive system of footwall laterals which are required by the mine development scheme. The initial mine plan called for in excess of 30,500 linear meters (100,000 linear feet) of footwall lateral drifts at a cross section of approximately 3.0 meters in width by 3.75 meters in height (10 feet x 12 feet). A Tunnel Boring Machine was selected for this work. The Robbins machine number is 146-193. This machine is approximately 4 meters (13 feet 5 inches) in diameter. The machine was modified extensively prior to commencing operation at the Stillwater Mine.

Jan 1, 1989

By Gregg E. Korbin, Robin B. Dill, Corey T. Dare, Tor L. Brekke, Larry R. Myer

A study was conducted to develop a fundamental understanding of the relationship between the size of an advancing tunnel face, the rate of excavation, and stand-up time in squeezing ground. Stand-up time is defined as the time elapsed after excavation that an unsupported tunnel face will remain stable. Squeezing ground is argillaceous rock or soil that exhibits pronounced time dependence of deformation and strength properties in-situ. A case history study documented the nature, causes, and solutions of several cases of stand-up time problems observed in the field. Then, in the laboratory, a series of physical model tests were performed in which model tunnel size, face advance rate, material properties, and pressure (representing overburden pressure) were varied. Stand-up time was found to increase as advance rate was increased or tunnel size decreased. In addition, an influence of advance rate on the definition of stability ratios was established.

Jan 1, 1981

By Y. Ooishi, Y. Matsumoto, T. Arai, H. Ohta

The multi-circular face shield (MFS) is a new type of tunnelling machine for construction of the special cross section and has been put to practical use in 1988. The MF shield has two circular faces partially overlapped in a single shield machine and can construct the cross section shaped like glasses for the double track railway. And it is possible to equip two or more cicular faces horizontally or vertically, if necessary. During the development of the MF shield the experiments have been carried out for the purpose of estimating the excavatability and the face stability of the MF shield. As a result it was confirmed that the both types of MF shield (one with double faces aligned horizontally and the other with double faces aligned vertically) has higher performance in the face stability and lower value in the cutter torque and the total thrust than the conventional circular shield.

Jan 1, 1991

By S. K. Kawatra, S. T. Bagley, T. C. Eisele

The use of the bacteria Thiobacillus ferroxidans to catalyze pyrite dissolution in coal is well known, and recent investigations have shown that T. ferrooxidans are also capable of rapidly altering the pyrite surface to facilitate its removal from coal by froth flotation and oil agglomeration. However, the effect of reactor design on the bacterial leaching rate is poorly documented, and the ability of bacteria other than T. ferrooxidans to affect pyrite flotation has been unknown. In this study, the effect of a number of different microorganisms on the flotation of unoxidized pure mineral pyrite has been investigated, and it was shown that organisms other than T. ferrooxidans are also capable of depressing pyrite flotation. In addition, comparative studies of leaching in shake-flasks and pachuca tanks have shown that the pachuca tanks allow leaching to proceed to a greater degree and at a significantly accelerated rate.

Jan 1, 1989

By G. L. Finfinger, F. E. McCall, A. A. Campoli, M. D. Zuber

Injecting pressurized water into a coalbed prior to mining reduces mining-generated respirable dust. Because of economic and geological barriers, water infusion for longwall dust control in the United States is now limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes that are drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob-gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob-gas boreholes. Computer coalbed-reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water-infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1997

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article concludes a two-part series on the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. Discussed are the consequences of fuse abolishment, the technical feasibility of changing to an alternative system, and an economic analysis of initiation systems. Last month, part one (ME, pages 31-35) described current use of initiation systems, incidence of accidents, and consumption values for safety fuse and other initiation systems. Consequences of Fuse Abolishment Cap and Fuse Manufacturers Two major safety fuse manufacturers, Ensign Bickford and Apache Powder Co., share the US fuse market. Marketing of Ensign Bickford safety fuse is done by Dupont. Dupont manufactures electric caps as a main product and recently introduced a new nonelectric initiation system (Detaline). Therefore, Dupont would be only slightly affected by the elimination of safety fuse from metal and nonmetal mining. Ensign Bickford, though a larger manufacturer of fuse, does not appear to emphasize the safety fuse market. In fact, safety fuse sales represent only about 10% of Ensign Bickford's total sales volume. Ensign Bickford is strongly pushing its Nonel product. It appears, therefore, that the elimination of safety fuse would have a limited effect on Ensign Bickford, and could ultimately be to the company's advantage. Apache Powder Co., however, would be seriously affected if safety fuse was eliminated. Safety fuse, although not its only product, constitutes a major source of revenue for the company. It currently does not manufacture a substitute product. Apache Powder Co.'s manager agrees that prohibiting the use of safety fuse would result in a greater market share of initiators for Ensign Bickford. Hercules could also benefit from the prohibition of safety fuse. Metal and Nonmetal Mining Industry According to an explosive company contact, elimination of safety fuse by a mandatory regulation would force some of the small, marginal mines out of business. Another powder company representative believes that eliminating safety fuse will result in uneasy situations for small operators not familiar with other techniques. These operators try to minimize the costs and traditionally like safety fuse. He believes that insufficient proof exists to substantiate the overall safety increase if the fuse is eliminated. Fuse manufacturers and distributors disagree, then, about the impact of safety fuse elimination. However, they tend to agree on some important points: • Safety fuse can be a safe method if applied properly. • Electric blasting can be dangerous due to stray currents, and may have higher misfire rates than safety fuse. • It is very difficult to compare the rate of misfires and partial round failures for different systems. This is due simply to the nonavailability of such data. In many cases, the misfires are not even reported to the shift boss, as required by regulations. • Safety fuse has high acceptance in certain applications, such as a face where Nonel or detonating cord are used, or in open-pit blasting. • The safety fuse industry appears to be phasing out on its own. It is expected that the fate of the safety fuse market will be similar to that of black powder. An investigation by Nitro Noble of Sweden "clearly states that the diminishing use of safety fuse has considerably reduced the accidents in Swedish mines." Mine Data Acquisition and Analysis As a part of the study effort, visits were arranged to 24 metal and nonmetal mines. In most cases, underground visits were accomplished. At least one drilling and loading operation was witnessed. The mines were grouped into four mining areas: Wyoming, Montana, Idaho; western Colorado and eastern Utah; Missouri; and southern Arizona. Of all mines visted, the safety fuse system was used in 11 mines, electrical system in seven, Nonel in five, and the Hercudet system in one surface mine. At each mine, the manager, foreman, and blasting crew were interviewed for information and opinions. Besides informal discussions with mine officials, a questionnaire was also filled out for each mine. Due to the extensive length of the information gathered, these data are not presented here.

Jan 2, 1984

By Edward J. Sterne

Several shale-hosted Pb-Zn-Ag deposits have been discovered in the northwestern Brooks Range, Alaska. Best known among these are the Red Dog, Drenchwater Creek, Lik, Ferric Creek, Hot Dog Creek, and Competition Creek deposits. They occur in a tectonically disturbed sequence of of Mississippian to Triassic shales, argillites, and cherts, and most are spatially associated with volcanic rocks. The sulfides are hosted in shales as disseminations, banded layers, massive lenses, and crosscutting veins. Detailed geologic descriptions of sulfide prospects in the Brooks Range were given by Tailleur (1970), Nokleberg and Winkler (1978), and Plahuta and Robinson (1979). Lange et al. (1980) discussed the formation of the deposits, the nature of the mineralizing solutions, and the temperature of formation on the basis of sulfur isotope studies. More recently, Harrover et al. (1982) detected a correlation between sulfide mineralization and high-temperature formation of charts associated with the sulfides by oxygen Isotope and chert crystallite size determinations.

Jan 1, 2013

By Randhir Sehgal

Heavy media processes have been used for cleaning +28 mesh coals for a number of years, Two applications, i.e., the vessels and the cyclones are widely used in the U. S. for this purpose. The basic reason for the popularity of these systems is their extremely high efficiencies for particle sizes above 28 mesh, However, application of heavy media technology to fine coals below 28 mesh, has been limited due to the following reasons: o Inability to make size separations effectively at sizes below 28 mesh o Necessity of feeding large quantitites of magnetite to the separators o Difficulty of recovering magnetite in the presence of large quantities of coal o High levels of coal contamination in the recovered media, leading to high circulating loads and ineffective control of media gravity

Jan 1, 1981

By G. E. Slagel

On August 3, 1987, a hearing was held by the House Subcommittee on Energy and the Environment to commemorate the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). Four panels of environmental/citizen group representatives went before the Subcommittee to report on the state of affairs (from their perspective) of the coal industry and the Office of Surface Mining, Reclamation and Enforcement (OSMRE) As expected, these groups had little positive news to report and continued to focus on glaring deficiencies within the surface mining program. They indicated that gross abuse of SMCRA has continued over the past ten years and the states have performed poorly. Congressman Udall's opening comments perhaps best characterized the mood of the group with his statement that "The Act has not accomplished what I or the people of the coalfields had hoped." and " ? a segment of the coal industry has continued in its bitter and implacable opposition to the most basic of environmental controls."

Jan 1, 1988

By R. H. Murray

The Kamyr countercurrent tower leach process consists of a true countercurrent leach ?with a flocculated ore and fibre mixture entering the top of the tower and a cyanide solution or alternative lixiviant as well as a barren wash solution entering the bottom of the tower. It offers the possibility of including the entire leaching, solid-liquid separation and clarification processes into one unit or tower as opposed to the multiple leach tanks, filtration and clarification sections required in a conventional leach and precipitation plant. The tower process has been demonstrated in the laboratory and found to be effective for leaching gold, silver and other amenable ores. Based on laboratory results, Gencor and Kamyr have jointly constructed a 200 ton per day pilot plant in order to prove the process on a larger semi-production plant scale.

Jan 1, 1989

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

 The paper demonstrates that Belle Fourche Shale (BFS), an abundant shale, can be transformed into a ceramic through careful characterization and thermal processing. The study explores the potential of BFS ceramics for use as refractories and thermal energy-storage devices, highlighting their high thermal storage capacity, good thermal shock resistance, and cost-effectiveness.

Dec 1, 2023

By V. F. Hollister

Epithermal gold deposits occur in and near the marginal fault that circumscribes the Goldfield, Nevada, Tertiary caldera. The gold occurs disseminated in alunite, pyrite, and kaolin- bearing silicified zones that are controlled by the circular faults. Other Tertiary calderas (i.e., Summitville and Red Mountain No. 3) have epithermal disseminated gold deposits located in and near their marginal circular faults in settings that resemble the Goldfield example. These additional caldera- controlled epithermal gold deposits are also characterized by alunite, pyrite, and kaolin-bearing silicified rock that act as hosts for the gold disseminations. The Goldfield District is therefore an exploration model for those seeking disseminated epithermal gold deposits in a caldera setting.

Jan 1, 1986

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines' tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969

By R. Callaway

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (?CERCLA?), as amended by the Superfund Amendments and Reauthorization Act of 1986 ("SARA?) establishes a comprehensive Federal regulatory program for addressing environmental and public health risks posed by releases of hazardous substances into the environment from a wide variety of industrial and other sources. The statute is primarily administered by the United States Environmental Protection Agency ("EPA"). The applicability of CERCLA to the mining, milling, and smelting industries (hereinafter referred to as the ?mining industry?) has been upheld by the courts and recently affirmed by Congress. The purpose of this article is to briefly outline the scope of CERCLA as it applies to the mining industry, the scope of EPA's activities pertaining to the mining industry under CERCLA, the types of remedies which may be pursued by EPA, and the liability scheme of CERCLA as it applies to corporate entities, managers, and shareholders involved with the mining industry. Natural resource damage claims, State cooperative agreements, and other State-related issues will not be discussed.

Jan 1, 1988

By Earl Cook

Introduction Men like physical power because it gives control over nature and over other men. Physical power comes in two common forms: explosive and non-explosive. In both forms, the most powerful devices yet invented make use of nuclear energy: on the one hand, the hydrogen or fusion bomb, and, on the other hand, a nuclear power plant. For some nations, nuclear power offers a measure of independence not otherwise available in a time of diminishing and unevenly allocated fossil fuels. Consequently, it has great attraction. Unfortunately, the application of nuclear energy (especially fission energy) to either explosive or electrical power entails a singular risk, that of injury from ionizing radiation, both natural and induced; this risk is found in all stages of the nuclear-fuel cycle, from mining of fissionable materials to the disposal of wastes produced in the "burning" of nuclear fuels. The health costs of nuclear power were not fully assessed in the early stages of the development of nuclear technology and some of them were not properly guarded against, either in the USA, which led the world into the nuclear age, or in Canada, which followed an independent path. What I shall do in this paper is to sketch the history of nuclear regulation in our two countries, to point out what I consider similarities and differences, and to suggest that regulatory history, as perceived by a concerned public, has a great deal to do with what is possible today and probable tomorrow, in other words, with public acceptance or rejection of the nuclear option. The U.S. situation As we sow, so shall we reap. In the USA, further expansion of the nuclearpower industry has been almost stymied by government actions that reflect mounting public concern. There is no national storage facility for spent reactor fuel and it has been decided not to reprocess it; consequently, existing power plants are about to choke on their own wastes. Since the Three Mile Island accident, no new nuclear plants have received operating licenses, although several are ready to start up. The uncertainty of future government action has caused the abandonment of plans for a number of new nuclear plants. In addition, many research projects related to medicine and agriculture, which produce low-level radioactive wastes, are about to be shut down for lack of licensed disposal facilities. Some would maintain that this situation has come about because of the low benefit-to-cost

Jan 1, 1980