Search Documents

By L. G. Austin, R. C. Klimpel

Batch breakage kinetic tests were performed in a mill of 0.3 m diameter for a range of mill conditions. Accurate simulation required the measurement and use of factors which accelerated the specific rates of breakage of the top sizes as finer material accumulated in the slurry. These factors depended on the size distribution expressed relative to the top size, not the absolute size, suggesting that they are due to a packing effect not a rheological effect. The data simulated correctly a series of steady-state continuous tests in a mill of the same diameter providing values were corrected to the hold-up, ball load, slurry density, and size distribution measured in the continuous mill tests.

Jan 1, 1990

By A. W. Khair, J. A. Organiscak, M. Ahmad

This paper describes research that seas conducted on bit wear and respirable-dust generation. The investigation was performed by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy and dust of one type of conical bit cutting coal. The objective of the USBM study was to identify qualitative bit-selection guidelines. The objective of WVU's research was to determine optimum bit-replacement guidelines. Both research studies found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1996

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60 percent and 40 percent, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert, and a rigid insert for cleaning the roof bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the coveralls when using either of the inserts.

Jan 1, 2002

By P. V. Avotins, D. R. Nagaraj, S. S. Wang

Xanthates and dithiophosphates are the most commonly used collectors in the flotation of sulfide minerals. Other reagents such as thionocarbamates, mercaptobenzothiazoles (MBT), mercaptans and xanthogen formates occupy niche positions in industrial collector use. Over the last ten years there has been much activity by chemical companies to develop new collector compositions. The new collectors are aimed at meeting specific process needs such as recovering an increment of valuable metals, improved sulfide separations, increased flotation kinetics, and reducing reagents costs. A review of the patent literature shows that American Cyanamid (Cytec), Dow Chemical, Phillips Petroleum, Sentrachem Ltd., Henkel, Montan Chemicals and Elf Aquitaine, among others, have been active in sulfide collector research. Several companies have achieved considerable success in laboratory and plant tests of the new collectors; however, commercial acceptance for plant usage has been slow. Those most advanced have been plant tested extensively and some are in day-to-day use. The new collector types in this category are: Modified thionocarbamates, dithiophosphinates, organic sulfides, trithiocarbonates, monothiophosphates, and modified thioureas. Others such as substituted mercaptobenzothiazoles and monothiophosphinates have been tested in the laboratory. The chemistry of collectors developed in the last 10 years, their preparation, physical properties and their potential for commercial use are reviewed in this paper.

Jan 1, 1994

By L. A. Feldkamp, L. I. Davis, F. Yuan, G. V. Puskorius

Emerging technologies such as neural networks and fuzzy logic have many potential industrial applications in diagnostics, modeling, and control. In the automotive industry, applications can be divided into those that impact manufacturing processes and those that relate directly to the product. Though discussion often centers on neural networks deployed in hardware, their potential in the development of problem solutions (however deployed) could easily be of greater importance. Here we concentrate on the use of neural networks for modeling and control, using a simulation of vehicle active suspension as a concrete example.

Jan 1, 1993

By S. L. McGill, P. B. Comba

Many gold producing states are requiring rinsing of spent heaps to render the leached ore compatible with the environment and are placing reatrictiona on effluent pH, cyanide, and metals concentrations. Parameters which may affect efficient rinsing of heaps have been investigated by the U.S. Bureau of Mines in laboratory column studies. Rinse profiles for cyanide, metals, and pH as a function of the volume of water passed through the spent ore are presented. Fresh water rinsing of spent ore in columns showed that rinsing of cyanide was not affected by the rinse solution application rate. Interrupted rinsing with a rest period between applications reduced the volume of water required to meet effluent cyanide concentrations. Chemical oxidation of the effluent with recycle of the rinse solutions reduced effluent cyanide concentrations and the volume of waste solution generated. Water rinsing was not successful in reducing the alkalinity of the cement agglomerated ore. A dilute acid solution had to be applied after cyanide removal to reduce effluent pH levels to specified limits.

Jan 1, 1991

By Y. M. Jiang

From underground instrumentation data and from direct observation of longwall panels, it was demonstrated that growth of the main-roof overhang causes an extremely high roof weighting on the face supports. This can result in catastrophic effects on the supports when the roof-weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on the characteristics of main-roof breakage and its effects on shields at different locations along the face. The study was based on monitored shield data, theoretical analysis and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed to define the main-roof failure modes and to understand the maximum roof-weighting intensity imposed on the shields. From this study, it was found that the effects of main-roof breakage on shields are chiefly related to the shield's initial-setting condition and to the final failure mode of the main roof.

Jan 1, 1996

By S. Mason

Many organizations are realizing that continual improvement in health and safety relies on addressing the potential for various forms of human error. Of these, rule violations are often the most frequent form associated with accidents. These occur when an individual (or individuals) deliberately contravenes established and known safety rules. They have been associated with up to 90% of the accidents and other incidents in some industries, and yet they rarely receive the systematic attention they deserve in the promotion of safety. This paper presents underlying motives that cause violations. These can vary significantly from mine to mine and from job to job. Managers need some measure of the attitudes of the violators to determine the underlying motives behind the violations if they are to determine effective strategies for promoting safe behavior. Questionnaires form the starting point to address attitudes and the motives behind rule violations. The choice of the most suitable questionnaire, how- ever, will vary from organization to organization. Guidelines on the choice of questionnaire are offered.

Jan 1, 2000

By K. A. Natarajan, M. K. Yelloji Rao

The effect of galvanic interactions among sulfide minerals such as chalcopyrite, galena, and sphalerite in the presence and absence of a grinding ball material on the flotation recovery of chalcopyrite has been studied. X-ray photoelectron spectroscopy (ESCA) studies were carried out to identify the reaction products on the sulfide minerals after different apes of galvanic interactions. Galvanic contact with active minerals such as galena and sphalerite, either alone or together, significantly affected the floatability of chalcopyrite mineral, such an effect being more severely felt in the additional presence of a grinding medium as well as oxygen. Surface analysis studies revealed the presence of oxyhydroxide species of iron on all the sulfide mineral samples which were in prior contact with the grinding medium. The formation of such oxyhydroxide species of iron was found to be dependant on the relative electrochemical activity of the mineral. Probable electrochemical reaction mechanisms are discussed.

Jan 1, 1990

By Shaning Yu, Yosry A. Attia

The purpose of this work was to investigate the feasibility of using column flotation as a floc separation technique. In this study, the ultrafine coal (minus 25 microns) slurries were cleaned by using the Integration of column flotation with selective flocculation. It was found that using column flotation as a floc separation technique during the "cleaning" stage, achieved much better results than that either using column flotation as a rougher separation technique for coal flocs, or using It directly to recover the ultrafine coal from the slurries without adding selective flocculant. Thus, the ultrafine coal slurries were first separated by selective flocculation process to reject a certain amount of the dispersed ultrafine ash minerals, and to aggregate the ultrafine coal particles as flocs. Thus, the entrainment of ultrafine ash minerals Into the coal floc-froth concentrate during flotation could be considerably reduced. Subsequently, the coal flocs were further "cleaned" by column flotation. The experimental results Indicated that this approach was technically feasible and particularly suitable for a slurry containing a large amount of ultrafine particles. The effect of flotation time, and collector dosage on column flotation of coal flocs were also Investigated and reported In this article.

Jan 1, 1988

By Steven W. Hunt, J. Patrick Powers, Roger C. Ilsley

Artificial groundwater recharge has been used successfully to mitigate water level drawdown in upper alluvial deposits during construction of the Milwaukee deep rock tunnels. Recharge wells in rock as well as soil were used. The effort reduced settlements from consolidation of compressible estuarine deposits, and has minimized damage to existing structures. The paper describes the geology that presented the consolidation problem, and the hydrogeologic conditions that caused the drawdowns. Also presented are the details of recharge well design, construction, operation and performance in an urban environment. The project design calls for grouting and lining of the tunnels to control groundwater in the long term.

Jan 1, 1991

By J. F. Dresser

Managing environmental compliance at a complex facility has the potential to bring a high degree of personal and professional satisfaction to both the corporation and the individuals responsible for day-to-day operations. The decade of the 1990's, however, has seen the emergence of a nationwide trend of aggressive federal and state civil and criminal enforcement for environmental violations. This trend, spearheaded by the U.S. Department of Justice (DOJ) and the U.S. Environmental Protection Agency's (EPA) Office of Enforcement, has the potential to place the corporation, its corporate officers, and compliance personnel at collective professional risk, as well as a growing tendency to place accountability on individuals. Management of environmental compliance has been anecdotally compared to a shooting gallery at a carnival, with the following exception: At the shooting gallery, successfully hitting nine out of ten targets usually brings a reward and recognition of shooting skill; hitting nine out of ten environmental compliance expectations not only brings agency consternation and negative publicity, but the "gallery" will likely shoot back with stiff fines and possible criminal allegations. Faced with the challenges of the new environmental compliance shooting gallery, corporations and professionals are often left asking themselves, "How do we (or more appropriately, can we) win at this game?" This paper examines recent federal enforcement statistics and offers several suggestions for coping with the responsibility of managing environmental compliance in the 1990's.

Jan 1, 1992

By J. R. Caylor

The Mine Safety and Health Administration (MSHA) advanced several initiatives last year to further protect miners' health. Regulatory efforts included the implementation of a Hazard Communication rule for all mines, work on the Single Sample rule for all coal mines, and the Plan Verification rule for underground coalmines. Development and application of new technologies are actively encouraged in preventing miners' hearing loss and respirable dust overexposures. MSHA's successful x-ray program for screening of black lung among coal miners completed its third year. Compliance Assistance efforts are focused on Best Practices, outreach, and technical support for operators' specific challenges.

Jan 1, 2003

By M. W. Rutland, E. Manev, R. J. Pugh

Data collected from several different fundamental surface chemical techniques were compared to study the interfacial interactions in the dodecylaminelmica flotation system. In the present study, the method used was the microinterferometric free foam film technique of Scheludko (1967) in which the stability, thickness and interfacial potentials at the air/dodecylamine solution interface were determined. These results were compared to previously published data, obtained from surface force measurements (Rutland et al. 1992), in which the interaction and hydrophobic adhesion (pull-off force) between molecularly smooth mica sheets in the amine solution had been reported. Also equilibrium contact angle measurements were used for comparison. The data was collected over a range of pH values and related to the batch flotation response of mica in dodecylamine solution. It was found that maximum flotation occurred at pH 8, but this did not correlate with the minimum in double layer interaction potential. However, it appeared to correspond with a tightly packed collector monolayer giving maximum hydrophobicity to the mica surface. Finally, from the extended DLVO theory, it was shown that heterocoagulation between the bubble and the mica could only occur, providing there was a very long range hydrophobic interaction force to counterbalance the repulsive van der Waals and electrostatic forces.

Jan 1, 1995

By G. A. Doyle

Until the suspension of conventional operations in 1996, the White Pine Mine was the second-largest active underground copper mine in the United States, underlying an area of approximately 30 km2 (13 sq. miles) in the Upper Peninsula of Michigan. The mine operator intends to initiate in-stope solution copper mining by circulating a solution (lixiviant) of mine water, sulfuric acid and ferric iron through rubblized ore. As planned, the solution would be retired in the mined-out stopes following completion of the solution-mining activities. Investigations into the fate of the retired solution indicated that the solution, through time, would change from an acidic, metal-rich solution to a near-neutral, reducing solution containing much lower concentrations of metals. Investigations included reaction-path modeling (EQ3/6) and laboratory and in-mine tests. The combination of neutralization and reduction will result in precipitation of most metals, primarily as metallic sulfates, chlorides and sulfides.

Jan 1, 1997

By D. R. Spears, C. E. Jordan

In an effort to improve flotation efficiency of the domestic minerals industry, the US Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20- µm, minus 625 mesh). The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine-particle, turbulent-flotation model. For the mineral system tested, improved flotation response was obtained in the laboratory testing with small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1991

By Raymond J. P. Brouzes

INTRODUCTION [A Decade After the 1972 Stockholm Conference] The UN-sponsored Stockholm Environmental Conference held just over 10 years ago was the first successful attempt to achieve global recognition of environmental issues. Indicative of the lack of concrete involvement in environmental protection to that time was the fact that only 15 nations had a department or ministry responsible for environmental affairs compared to today's 143. Many governments were uncertain of what were the most serious or pressing problems in their country. There was obviously a need to both identify those issues and to determine how to manage them once identified. At the same time, the public at large was becoming more critically aware that environmental protection had been neglected by government and often ignored by industry. It soon became evident that large amounts of money would have to be spent to redress some of the more evident problems. However, many developing nations were reluctant to slow down the much-needed industrial growth by imposing costly environmental controls on industry. In fact, some waived environmental control altogether as an incentive to attract industry. In some sectors, it was often stated that industrial development and environmental protection were mutually exclusive activities. The need of an awareness, commitment and dedication by all sectors of society to protect their environment was just beginning to develop, replacing the rather simplistic view that all environmental problems were caused by greedy industry.

Jan 1, 1984

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit in Yemen contains at least 9.4 Mt (10.4 million st) of ore at a grade of 10.7% zinc, 2.2% lead and 77 g/t (2.2 opst) silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to a conventional zinc smelter, and it has been necessary to formulate a less-conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material at Yanbu, Saudi Arabia. To give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulfide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, presents the flowsheet for Yanbu and estimates preliminary costs for both operations.

Jan 1, 2003

By Adolf J. Jonaitis

Outokumpu developed TankCell flotation cell technology beginning in 1990, following 35 years of successful flotation cell experience and application. In 1994, Outokumpu proved favorable operating success of 100-m3 (3,500-ft3) TankCells for porphyry copper and zinc flotation. In 1995, evaluation of a 150-m3 TankCell led to the successful application of these large cells in several operations. More than 350 TankCells of 100 m3 and larger in volume have been installed and are in operation. Key features of the Outokumpu TankCell design will be described. In addition, discussion of operating data from various metallic mineral flotation operations worldwide will be presented. Large flotation cell development continues today, with operating cell volumes of up to 160 m3 (5,500 ft3) in operation.

Jan 1, 1999

By Lynn B. Hales, Randy Ynchausti, Jeffrey D. Mckay

Many consider rougher flotation control to be more of an art than a science. Some have even thought it impossible to make process control decisions and changes without human interaction. Controlling flotation bank pulp levels to maintain consistent pulling rates in the face of changing feed slurry flow rates, varying mineral types, and inconsistent reagent additions can be daunting. However, an advanced supervisory control strategy was installed on the plant floor to control an industrial rougher flotation circuit with little or no operator interaction. Plant staff monitored the flotation circuit under supervisory control and reported benefits of up to 4% improvement in copper recovery above that achieved with an older supervisory control strategy. To accomplish this work, a novel use of instrumentation to solve a flotation bank pulp level control problem was employed, a new implementation approach was used to correct some flaws in the older approach, and careful attention was paid to a few key process control principles. This paper discusses important aspects of these activities.

Jan 1, 2000