Search Documents

By R. Thornton

Montana Tech is located in the historic mining town of Butte, MT and is adjacent to the Orphan Boy mine. This abandoned underground mine will be the heat source for a down-hole heat exchanger (DHE)/heat pump system. The mine was abandoned in the 1950?s and has since filled with water to within approximately 30 m of the surface. The shaft is composed of a 245 m vertical shaft connected with horizontal crosscut drifts at 60 m and 150 m below the water level that connect to a large stope with approximately 1250 million liters of water at a consistent 75-78°F temperature. The intent is to build this heating system to augment or fully heat a newly built 2,000 m2 building on the Montana Tech campus. As designed the system uses ?off-the-shelf? parts making the basic configuration straightforward with the exception of the DHE?s which need to be placed into the vertical shaft. Because there is little or no examples of placing the heat exchangers in a vertical shaft, the primary focus of this work was to model the heat exchanger placement and configuration in the vertical shaft such that thermal currents develop between the stope and vertical shaft in, via the horizontal crosscut drifts, in order to move the water and thereby provide the required energy. This study includes the modeling of water flow, temperature profiles, and the heat contribution from the surrounding rock walls.

Feb 27, 2013

By L. Ozdemir, M. Cigla

This paper presents and discusses some of the computer models developed and currently used at the Earth Mechanics Institute (EMI) of the Colorado School of Mines (CSM). These include the performance models for full and partial face machines. Examples of input and output of these models will be illustrated for typical mining operations by using machines such as Tunnel Boring Machines (TBM), Continuous Miners (CM), Marietta borer miners and longwall drum shearers. The general approach to modeling and the available models are discussed and some examples of these models are presented. The comparison between the estimated and achieved performance, as well as the degree of improvement in the performance due to balancing and modification in cutterhead design are also discussed.

Jan 1, 2000

By M. Okido, W. Wei, L. Chai

The kinetics on the growth of Thiobacillus ferrooxidans was studied by use of series piezoelectric quartz crystal ( SPQC ). Arsenic ioninhibits the growth of Thiobacillus ferrooxidans, which is consistent with the previous results by other measuring method. This further demonstrates that the SPQC can monitor the chemical activity of the growth of Thiobacillus ferrooxidans. Cupric ion accelerates the growth of Thiobacillus ferrooxidans. The mechanism was discussed, it was considered that copper promotes the protein enzyme of Thiobacillus ferrooxidans, rustic yanin, to form over the range of cupric ion concentration studied. There action order of cupric ion in accelerating the bacterial growth is 0.067. The growth of Thiobacillus ferrooxidans is dependent on temperature, the apparent reaction activation energy decreases from25.56 kJ / mol to 18.32 kJ / mol because of the addition of 10 mg / L Cu(II) to the bacterial growth solution of pH 2.0 at initial inoculum of 10%.

Jan 1, 2000

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

This paper proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology. The new parameter was defined as the total strong layer thickness (tstr) that represents the strength and stiffness of the overburden with a single value. Twelve field measurement case studies from 11 different U.S. longwall mines with different overburden geologies were used to develop the new methodology. 2D numerical models of these case studies (and additional parametric runs with different panel widths) were verified against field measurements such as surface subsidence and stress. Statistical analyses using the model results were conducted for a loading model with the new tstr parameter as one of the variables. The new methodology was found to have a coefficient of determination (R2) of 85% when compared to the field measurements and the parametric models. The method was then tested for practical implementation for pillar design. The percentages of load carried by the gob as estimated by the new method were implemented into the LaModel program, that is commonly used in the coal industry. The results obtained from LaModel were compared to the available field stress measurements, and the new method implemented into LaModel was found to give successful results.

Jul 18, 2022

Many of the world?s largest existing mines are considering substantial step changes in production volumes, compensating for declining ore grades while trying to address increases in world demand for resources. The natural configuration of coal deposits allows for many mine development openings along the strike to access the ore body and thus increase volume. Similarly, with iron ore the nature of the deposits means that additional capacity can easily be added by opening up new mesas and providing extensions to infrastructure. On the other hand most of the non-ferrous metaliferous deposits form vertically and additional extraction volume comes from increasing depth. Underground mining from the base of the strata allows for large extraction rates, but block or panel caving operations develop at rates dictated by the geophysics of the overlying strata and the need for massive tunnelling developments to establish sufficient extraction points for high volumes. For really big mine production capacity, open cast mining still allows the easiest development of more massive mining techniques. But there remains the question of whether there are limits to how large an open cut mine can become in terms of throughput?

Feb 27, 2013

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent upon the application, mineral properties and available instruments. Different instruments produce images that display different features; in order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application.

Jan 1, 2001

By José Mirão, Pedro Madureira, v Costa, Patrícia Conceição

"The exploration of seamounts south of the Azores during the EMEPC/Açores/G3/2007 campaign allowed for the collection of 30 Fe-Mn crusts from the Atlantis, Great Meteor, Small Hyeres, Irving and Plato seamounts, as well as from the East Azores Fracture Zone. These were the first samples of Fe-Mn crusts studied from these seamounts. The Fe-Mn crusts were analyzed using multiple analytical methods.The crusts are fairly homogeneous, showing typical textures for this type of occurrences. The Fe/Mn ratio, patterns and concentrations in rare earth elements, and the great homogeneity of the crusts lead to the conclusion that they have a hydrogenetic origin, precipitating directly from seawater. Although the content in Fe and Mn of the crusts is consistent with data available for the Atlantic, the mean concentration of Co is comparable to the average values for the Pacific. Cu and Ni show lower values than the ones known for the Pacific."

Sep 1, 2014

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and thus deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the go band to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Feb 27, 2013

By J. Geyer, B. T. Burton, H. W. Newcomen

For open pits developed in tropical climates the upper portions of the pit walls are often located in residual soils and weathered rock. Due to the presence of relict structures, and the relatively low strength of the residual soils and weathered rock, design slope angles in these materials have to be developed by blending the results of kinematic assessments of geologic structures with rock mass stability analyses and traditional soil mechanics. Background information on the engineering considerations of residual soils are discussed, and the results of geotechnical assessments for proposed pit design of the Brisas del Cuyuni Project, located in southeastern Venezuela, are presented.

Jan 1, 2000

By Ray Brainard

The subsurface investigation for the Reach 4 Tunnel was expected to be completed in a single phase. This assumed that data from two nearby previous tunnels, combined with limited new subsurface information and surface mapping would be sufficient to characterize the rock behavior. Unforeseen rock conditions and complex faulting led to the recommendation for a second phase. This decision was not reached easily, as much of the follow-on work required helicopter support, and associated costs. The second phase of drilling found significantly more variability than the first phase and led to a very different and better understanding of the geologic and geotechnical conditions, and rock characterization.

The SFR system utilizes a skimmer or extractor placed at or near the slurry-froth interface where there is a higher concentration of valuable mineral particles. With assistance of hydrocyclones, it is possible to classify the extracted particles into coarse and fine particle streams, that can be handled separately. It also allows the coarser solids to be separated from entrained low-value fines. The first test results with the SFR system significantly improved both coarse and fine particle recovery in a flotation cell. The SFR system was tested in the flotation circuit at a copper-moly concentrator, and the results show that the use of the skimmer has huge potential to increase the froth recovery (Rf) of both molybdenum and copper.

Jan 1, 2012

By S. Suwansawat, D. J. Maconochie, C. C. Chang

This paper describes the overall delivery of the tunneling for the Mass Rapid Transit Authority of Thailand’s Chaloem Ratchamongkhon Line in Bangkok and the constraints provided by the alignment. Eight earth pressure balance tunnel boring machines were employed under two major civil works contracts to drive approximately33 kilometers of tunnel in soft saturated ground beneath the crowded streets of Bangkok. Responsibility within the contract for building damage provided an inherent control for ground movement arising form tunneling when the right of way was narrower than the influence zone. These limits affect the earth pressure balance requirements and permissible ground loss. The methods adopted to limit ground movements and deal with the various obstacles to tunneling influenced the design and operation of the machines. The challenges provided by the need to tunnel through numerous lines of piled foundations of canal bridges and overpasses crossing the alignment are described.

Jan 1, 2001

By G. W. Bonnell, D. A. Young, D. G. Genter

Through 1996 and 1997, CANMET and the Cape Breton Development Corporation (CBDC) conducted a project to study the Phalen Mine’s 7 East longwall ventilation network to help determine methane emission patterns that were having a negative impact on coal production. Increased methane emissions were primarily related to mining depth and were also affected by the influence of a large sandstone body located above the worked seam. The research included the installation of tube bundle systems to monitor waste (gob) methane and pressure differentials. The focus of this paper is on the novel use of tracer gas techniques that helped shed light on the performance of the ventilation system and in determining the methane migration paths in the waste.

Jan 1, 2001

Introduction The science of geometallurgy requires that ore characterization be performed holistically, that is, with consideration of ore quality on plant performance and product quality. Geometallurgy, by definition, requires knowledge of geology, mineralogy, extractive metallurgy and pyrometallurgy. Examples of the ore characterization challenges for the geometallurgist in the production of iron ore pellets from low-grade Proterozoic iron formation are presented here. Ore Characterization Ore characterization, the quantifying of mineralogy, grain size and the texture of ores, is an often overlooked tool in improving process efficiency. Some mineral related problems are not unique to the production of iron ore pellets; e.g. the problems caused by expanding clays in flotation. The negative impact of carbonate minerals in the ore on pellet productivity and pellet quality are unique. The long and complex geologic history of Precambrian iron formations contribute to modifications of grain size and the introduction of complex textures.

Jan 1, 2007

By Daniel W. Kappes

Testing ores for heap leach operations traditionally follows a progression of bottle roll tests, bucket and column leach tests, and very expensive large field leach tests. Enough data is now available to streamline the procedures. Data from five different operations shows that recoveries from large field leach tests can be predicted from the bucket tests. Initial recovery times in large field leaches are longer than in bucket tests- a typical response is eight days versus twenty days to the same recovery percentage; but the ultimate percent recoveries (after 60 days) are normally very close. Methods of mining and stacking can radically affect recoveries from clay-rich ores. Leaching of uncrushed ores provides special testing problems, since accurate samples smaller than several tons cannot be taken.

Jan 1, 1981

By Richard A. Bideaux

With both unit costs per meter and average depth of drilling constantly increasing, there is a strong incentive to maximize the information acquired from drill holes, and then to make this information accessible to the geological staff. The larger the drilling project, the more advantageous computerization of data is over manual methods. The conversion to computer-readable form and the verification of large amounts of drill-hole data can be a substantial data processing task, but once accomplished, the benefits in increased accuracy and speed of interpretation will compensate for the time and effort spent in the work. For an exploration project progressing towards a preliminary feasibility study, about half of both the time and costs for all computer work of the entire feasibility study are devoted to drill-hole data base organization, and maintenance. Once drill-hole results are quantified and verified to be correct, they are immediately accessible and are not subject to further transcription or reinterpretation of errors. To obtain maximum benefits from computer utilization in this area, the drill-hole data base should be set up along with availability of the first data. For some companies, this may initially comprise a large number of purely speculative drill holes on a spacing of perhaps 1 or 2 km. Although few of these drill holes may encounter economic material, thought should be given, at this time, to the variables which will be logged when such material is found. In this way, it should be possible to set up a consistent format into which all future drill-hole information will readily be accommodated. This format may even be carried over into the data base requirements for an operating property.

Jan 1, 1979

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

Jan 1, 2005

By N. Chow

The recovery of manganese from lower grade resources has been studied for a number of years. Of key importance of prior work, was the discovery that higher valent manganese resource can be readily leached with sulfurous acid. This eliminates the need for high temperature reduction roasting that is conventionally used in processing high grade material. High temperature roasting is energy intensive, emits a large amount of carbon dioxide, and would not be economical for processing lower grade material. While the prior work provides important information to extract manganese from lower grade resources, the production of unwanted by-products, and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems, which to this point preclude commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low cost, environmentally friendly manner. Emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted by-products.

Jan 1, 2011

The National Mining Hall of Fame will hold its 13thAnnual Induction Banquet during MINExpo International 2000 in Las Vegas, NV. The gala black-tie (optional) event will honor eight legendary leaders of the mining industry. The event will take place at the Las Vegas Hilton Hotel on Sunday, Oct. 8. The induction ceremonies will salute mining greats elected by the board of governors from a list of nominees submitted by mining industry partners and the public. The members of the Class of 2000 will join 151 other inductees enshrined in the Mining Hall of Fame in Leadville, CO. The evening will begin at 6 pm with a cash bar reception followed by the banquet and program at 7 pm. Keynoting the banquet program will be Harrison (Jack) Schmitt. He was the geologist/astronaut of the Apollo 17 mission to the moon in 1972 (see related story on page 26). And he is the only scientist to “kick rocks on the moon.” Schmitt is also a member of the Mining Hall’s board of governors. Schmitt was also the keynote speaker at the First Annual Induction Banquet in Denver, CO in 1988.

Jan 1, 2000