Search Documents

By J. M. Hollow, D. E. Walsh, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Carbon fines are collected by a filter press because of their gold value. Samples of the carbon fines show that they consist of 20-30% carbon, 70-80% grit and 0.17-0.68 kg/t (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in a form of recrystallized free gold grains, with the balance being adsorbed gold on the carbon. High recoveries of gold and carbon were obtained in laboratory tests using froth flotation, with a high rejection of the grit.

Jan 1, 2001

By Charles W. Daugherty, James P. Gould, Kenneth R. Ware

INTRODUCTION As illustrated in Figure 1, the Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system (METRO) ultimately will comprise 100 miles of line divided among 10 routes. At this time about 46 per cent of the system is under construction or in operation. Planning and design of an additional 38 per cent is at an advanced stage. Of the 84 miles under development or construction, about 10.4 miles consist of soft ground tunnels, and another 1600 feet of mixed face. This paper describes most of the factors considered by designers in setting grades for such tunnels. It is hoped the paper will be a useful guide to planners and engineers in developing similar transit systems. The problems faced in Washington, including those related to geology, are not so unique that the solutions cannot be applied to other systems. The paper also may be of interest to contractors who have not perceived the logic behind the selection of a particular vertical alignment. An attempt is made to explain the background constraints that make most tunnel alignments a compromise among competing alternatives. Readers might assume that the choice of alignments is largely controlled by geological conditions. In fact this is merely one of many factors to be considered.

Jan 1, 1976

By E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. This is especially true in surface and underground coal and stone mining where large, noisy equipment predominate. Workers in coal preparation and stone processing plants have also been found to be subject to high sound levels that could potentially cause NIHL over prolonged periods of exposure. National Institute for Occupational Safety and Health (NIOSH) researchers have been conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by river dredging. Little is known about the noise environment and worker exposures in these environments, where processing and mining equipment similar to coal and stone are employed. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to identify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges, in several surface mine sand and gravel operations and in the processing facilities. The locations where workers are likely to be overexposed and were found to be most susceptible to noise overexposures are reported. Results indicate that there are areas on the dredges (crane, suction pumps, and diesel engines) where sound levels greater than 90 dB(A) are present. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration (MSHA) Permissible Exposure Level (PEL) of 90 dB(A) TWA8, laborers, mechanics, oilers, helpers, pickers, and greasers are the workers likely to be exposed to hazardous sound levels and thus develop NIHL over time. Knowledge of the equipment noise, area sound levels, and worker dose levels is information that management and employees can use to reduce exposures. Exposures can be reduced in certain areas through administrative controls and through engineering controls applied to the noisiest equipment.

Jan 1, 2008

In recent years there have been significant advances in computing power and programming technology, enabling more complicated processes to be modelled in greater detail. This has led to increased understanding of these complex processes, including mineral processing circuits. JKSimMet was developed over the past 35 years, incorporating outcomes from various research projects conducted at the Julius Kruttschnitt Mineral Research Centre (JKMRC), part of the Sustainable Minerals Institute at The University of Queensland. It is a steady-state software program that allows the user to mass balance, model fit and simulate crushing, grinding and classification circuits. JKSimFloat has been developed over the past 20 years, incorporating outcomes from the JKMRC and other institutions around the world through the AMIRA International P9 project ? The Optimisation and Simulation of Mineral Processing Circuits. It is also a steady-state software program, similar to JKSimMet, but is focused on analysing flotation circuits. Both programs have been used in a wide variety of optimisation and design projects over many years. This paper provides an overview of both JKSimMet and JKSimFloat and examples of how both programs have been used to better understand, develop and optimise mineral processing circuits around the world.

Feb 27, 2013

By Michael S. Zhdanov

One of the major problems of mineral exploration is the ability to reliably distinguish between uneconomic mineral deposits and economic mineralization. While the mining industry uses many geophysical methods to locate the mineral deposits, until recently, there was no reliable technology for mineral resources identification and characterization. The main goal of this project is to develop a new geophysical technique for subsurface material characterization, mineral exploration and mineral discrimination, based on electromagnetic methods. The proposed new technique is based on examining the spectral induced polarization effects in electromagnetic data using the modern distributed acquisition systems and advanced methods of 3-D modeling and inversion. The recovered parameters of the relaxation model will be used for the discrimination of different rocks, and in this way will provide an ability to distinguish between uneconomic mineral deposits and zones of economic mineralization using geophysical remote sensing technology (Zonge, 1976). The proposed research and development is undertaken using multi-partner collaboration between the University of Utah, four major mining companies, Kennecott Exploration, BHP Billiton World Exploration Inc., Placer Dome Inc., Phelps Dodge Exploration, and Zonge Engineering Inc., which is equipment manufacturer and service provider to the mining industry. The multi-partner collaboration between the academic institution, the University of Utah, and mining industry helps to identify the appropriate mining target and conduct the field experiment for practical demonstration of the developed new technology, which is an important part of the this project.

Jan 1, 2005

By J. Pesl, R. Hurman Eric

Metal-slag phase compositions of molten iron and ilmenite smelting slags or solid titanate phases were determined between 1500° and 1700°C. The influence of oxygen partial pressure and impurity oxide additions including Al2O3, Cr2O3, MgO and SiO2 were investigated along with amount of reductant-carbon. The XRD revealed that the quenched slag crystallized as pseudobrookite (M3O5) solid solution in equilibrium with iron. Silica additions formed separate silicate phases because of its immiscibility in the titanate phase. Under strong reducing conditions iron oxide was almost completely reduced and the slag phase solidified as a consequence thereof. Cr2O3. SiO2 and MnO were also reduced to a high degree. Under weak reducing conditions the slag was fully molten and non of the impurity oxides were reduced. A significant portion of manganese, some magnesia and silicon, in the form of SiO gas, were removed via the gas phase due to their considerable vapour pressures. Alumina was not reduced under the applied conditions. A comparison of the experimental results with industrial data clearly suggested that industrial ilmenite smelting process operated under non-equilibrium conditions.

Jan 1, 2005

By G. Karahalios

Industrial minerals have always enjoyed an important share in the technological growth of any country in the world. Today, extraction and trading of industrial minerals has expanded, but is also subject to stricter environmental guidelines. This paper presents the current status as well as the growth potential in the exploitation of industrial minerals in the countries of the south eastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, F.Y.R.O.M., Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. More specifically, annual production figures per country are presented for1992-1998. These figures are compared to each other and, where applicable, to world production figures. Trading of industrial minerals from these countries to Europe and the world and its effect to the local economies is also evaluated were such data is available.

Jan 1, 2000

By Steve Kral

For the past several years, copper producers have faced a tough business climate. Nagging low prices forced many them to reduce their production and make other drastic cutbacks just to breakeven. And sometimes even that did not work. But, like other downturns in the industry, this latest dismal copper market allowed technology to make further inroads into mining and processing operations. Now that the copper market appears to be making a turn for the better, those years spent investing in technology by equipment manufacturers and forward-thinking mining companies should begin paying off.

Jan 1, 2004

By M. J. van der Meulen

"The Netherlands has major resources of sand, gravel and clay, exploited mainly for construction works and the building materials industry. As in most western countries, mineral extraction meets with considerable societal resistance. To this end, Dutch minerals policy aims to prevent extraction by promoting economical use of materials, and the use of alternative (secondary or renewable) materials. Up till recently, it also included a system of production planning to sustain supplies of regionally scarce materials. Dutch policy development is reviewed and discussed in terms of pitfalls and possibilities for mineral planning in general. Promoting secondary substitution has been quite successful, and presents an example. In contrast, the production planning system has been controversial from the start and ineffective as a result, mainly because it attempted to solve supply problems without properly addressing the underlying resistance. For this reason the system is in the process of being abandoned. The full paper will be published in: Petterson, M., McEvoy F, & Marker, B.R. (Eds) 2005, Sustainable minerals operations in the developing world, Geol. Soc. Lond. Special report series, in press. This abstract is reprinted with kind permission of the publisher."

Jan 1, 2005

By Franz Walchshofer, Mark Kuchta, Nobuharu Isago, Ugur Ozbay, Wolfgang Dolsak

A series of in situ pull test were performed on a new design friction stabilizer bolt with the objective of determining its performance characteristics. The bolt is installed while drilling, thus improving safety and significantly reducing the installation time. An optional expansion element can be inserted into the bolt to provide an end-anchorage, which further increases the bolt’s capacity. In situ tests show that the pull capacity of the 2 m long new design bolt is about 15 tons. When installed with an expansion element, the pull capacity of these bolts becomes as high as 30 tons.

Jan 1, 2005

By Donivan L. Gordon

One of the several problems facing society today is that of disposing of its solid waste. Each year this nation spends approximately 4.5 billion dollars to collect, transport and dispose of some 360 million tons of domestic and industrial solid waste. Although considerable sums of time and money have been spent in researching various techniques for solid waste disposal, it is presently agreed that sanitary landfilling represents the most economic and universally adaptable solution to the problem of solid waste disposal. However, regardless of the factors favoring sanitary landfilling as the waste disposal method of choice, it should be recognized as carrying with it a potential for the degradation of ground- and surfacewater resources. Through an interdisciplinary effort regulations were promulgated during 1971 in the State of Iowa to govern sanitary disposal projects. Consistent with a set of rationales developed to preserve environmental quality, these regulations set forth hydrologic and geologic standards designed to protect Iowa's water resources. Minimum requirements have been outlined in the regulations through which the natural favorability of potential landfill sites may be evaluated. Natural favorability is primarily defined in terms of the hydrologic and geologic relationships between a proposed landfill site and those in the locality of the site. The regulations specify that leakage from a landfill to a subcropping aquifer must be less than 0.04 cu ft/day/sq ft at the base of the landfill. This factor is offered to quantify the maximum allowable leakage for all sites in unconsolidated sequences underlain by subcropping bedrock aquifers, Based on groundwater research in Iowa, the assumption is made that 50 feet of till will be sufficient to inhibit the downward flow of liquids from a landfill into bedrock aquifers. This assumes a difference of no greater than 40 feet in hydrostatic head between the water table in the unconsolidated sequence and that in the bedrock aquifer. Owing to the fact that bedrock aquifers in many areas of the state are mantled by less than 50 feet of till the regulations provide for site modification, through engineering, to meet the specified leakage standard, In such instances the leakage factor is evaluated by means of the generalized Darcy's Law Q = PIA where:

Jan 1, 1974

By J. Piper

Markets and Production Beryllium (Be), an extremely light metal, is used in many specialty applications. It the lightest element in Group 2A of the periodic table, with a specific gravity of 1.85 gm/cc, and a high melting point of 12850C (Calvert, 2004). The functional properties of beryllium are stiffness, strength, dimensional stability, resistance to corrosion from acids, and electrical and thermal conductivity. The ability to reflect neutrons and transmit x-rays, makes beryllium irreplaceable in uses such as precision optical components, inertial guidance systems, and in nuclear reactors (Anon, 1993). Beryllium is used in Cu alloys to strengthen and reduce corrosion in copper wire, and in lightweight oxide ceramics that are used as heat sinks, and as electrical insulators. The market revenue of beryllium can be broken down into the seven major groups below, and are plotted on the pie chart in Figure 1 (Anon, 2005). 1.) Telecommunications & Computer 2.) Magnetic & Optical Data Storage 3.) Aerospace and Defense 4.) Automotive Electronics 5.) Industrial Components 6.) Appliance, and 7.) Other.

Jan 1, 2007

By H. K. Lin

Cyclic voltammetric and potential step chronoam-perometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic and one cathodic peaks appear on the voltammogram between -0.50 and 0.80 V vs SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH, cyanide concentration and the rotating speed of the electrode on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2000

By F. G. Crack, R. V. Ramani, R. L. Frantz

Management for mine construction and development differs from that needed for routine mine production and maintenance. An integrated approach to managing mine development projects must consider contract documents; management organization of a project; the project manager's role and the field supervisor's responsibility; and the use of scientific techniques for planning, scheduling, executing, and controlling projects. Professional project management encompasses the following: • Preparing contract documents that establish technical and financial schedules, and detail the responsibility for the physical work commitment. • Developing a project's organizational structure, to clearly define the roles of the project manager and the field supervisors. • Establishing project management and field supervisor relationships, to avoid ambiguity in assigning responsibility and to ensure desired project progress. • Using management science techniques, particularly networking techniques such as the critical path method for planning scheduling, executing, and controlling projects. Project Versus Production Management Project management differs from routine production management in the following ways: • Uniqueness: A project is unique. Production operations tend to be repetitive. The magnitude of one-time capital expenditures for many facets of mine development warrant special skills and attention. These professional project development skills must already be available by prior experience in the management team. • Personnel: In projects, personnel are usually assigned on a specialty basis and frequently change with the project activity. On the other hand, production personnel work together, more or less permanently. • Management Structure: In a project there may be several staff-line relationships that are not clearly defined and change with changing project activities. In a production situation, the lines of communication and authority are usually well defined. • Time Frame: A difference between project and routine production management is that project activities have comparatively less well defined durations and often tend to be relatively short-term. Production usually has both long-term and short-term plans and well defined long-term and shor-term goals. In project management, formal, critical, short-term reviews are frequently required. In production management, five year plans can be formally adjusted quarterly and annually. Short-term weekly or daily reviews can be informal. • Response to Delays: Delays in a development project may occur without anyone being immediately aware of their existence or suspecting the magnitude of consequence. In contrast, any delays in the production process can be easily identified from prior results comparison. Additionally, the response is quick, usually in a set routine. This can be traced back to the management structure and personnel. • Control Techniques: Measurements of project progress for control are not easily made due to the variety of activities that are carried on at the same time by different work groups. The yard-sticks of performance measurement for individual activities, let alone for the total project, are not easily established. However, due to the difficulty in detecting project delays, a workable control system is vitally important to a project manager. To apply a scientific project control technique such as "management by exception" requires specific planning and monitoring from the project manager for each activity in the project. Production and productivity are quick and effective yard-sticks of measuring performance in a routine operation. Control techniques required in production management usually revolve around these measures. Construction Contracts The construction contract is an important document that establishes contract scope, technical and financial details of the work, and achievement deadlines. It may also serve as the contract document to pay for work done and to verify field progress with planned progress. In practice, it is a good idea to develop a job-specific contract. This whole area is replete with legal precedence and procedures, and it is not the intent here to deal with the intricacies of establishing a contract document. But it is necessary to have an understanding of major contract types. Construction contracts are extremely important legal documents. They may vary in work specifications and enforcement of the provisions. Due to their nature, they must be composed with legal help and will take some time to compile. Even with all the precautions and provisions, it is not uncommon to find owner and contractor disagreeing. Therefore, it is important to include a way to resolve any difference quickly and to incorporate aspects of the contract as part of an overall management control tool for efficient project management.

Jan 7, 1982

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By Thom Seal, S. J. Jung

This paper will combine three SME annual meeting presentations on reducing gold inventory in cyanide heap leaching. Information on Part I – Side slope leaching (SME 2003), Part II – Determining the dry zones using geophysical resistivity (SME 2004), and Part III - Presents a new technology “Hydro-Jex”, to introduce the required lixiviants to the un-leach or under-leach zones in heaps (SME 2005). This paper will describe how Newmont Mining Corporation continues to improve the economics of the heap leaching process for precious metals recovery.

Jan 1, 2005

By H. Maleki

In this paper, long-term measurements in five underground mines are presented to demonstrate how these measurements can be applied to stability evaluations and design of underground excavations. These case studies address both the global aspects of strata response to mining activities as well local ground behavior and support loading. The measurements include static (stress and deformation) and geophysical. Case studies quantify pillar behavior, roof-floor deformation patterns, overburden response, and microseismic activities. Large-scale studies quantify the nonuniform nature of overburden deformation and collapse. Local measurements address yield and stable pillar load deformation characteristics, as well as the performance of support systems under combined axial and lateral loads.

Jan 1, 2002

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By P. Sangurmath, C. Gundewar, M. Riyazulla, V. Vasudev, N. Shadaksharswami

Dharwar craton in the southern Indian shield, comprises the Neoarchaean foreland in the west and a relatively younger accretionary complex composed of granitoids and intervening gold-bearing volcano-sedimentary belts. The Hutti schist belt hosting a major gold producing mine is situated in the northern part of the eastern Dharwar craton. It is a horse-shoe shaped structure comprising predominantly of pillowed metabasalt of tholeiitic composition with minor amounts of clastic sediments and felsic volcanic rocks. The belt is intruded on all sides by circular to tabular bodies of granites and granodiorite. Important gold deposits are located at Hutti, Hira-Buddini and Uti villages. Felsic volcanics in the Hutti belt occur as tabular bodies of quartz porphyry and breccia. Two of the gold-bearing reefs in the Hutti mine, Viz., Middle and Strike reefs are intimately associated with tabular sub-vertical sheets of mylonitic quartz-feldspar porphyry intruding pillowed metrabasalt. In Uti mine area, the felsic volcanics occurs as a tabular body. At Hira-Buddini, the felsic volcanic occur as a irregularly shaped sheet in pillowed metabasalt. Mineralogical and geochemical studies suggest that the felsic volcanic rock in Hutti mine area is a rhyolite and at Uti and Hira-Buddhini it is of dacite composition. Scheelite occurs as veins, veinlets, stringers and blebs along fracture planes of felsic volcanics in the Hutti mine area, whereas at Uti and Hira-Buddini it is insignificant. On the basis of spatial association of metabasalt and felsic volcanics and on geochemical grounds, we interpret that the felsic volcanics might have originated by the partial melting of basalt. REE patterns of the granite, granodiorite and metabasalt of Hutti are similar to each other indicating that they could be co-magmatic. However, REE in the Hutti felsic rocks is significantly higher than in Uti and particularly Hira-Buddini mine areas. The two felsic volcanic samples drawn away from the mineralized zone from all the three mine areas were analyzed for tungsten. In Hutti one sample assayed 0.15% and another 0.062%. At Uti, in one sample it assayed 0.056% and another less than 1 ppm, whereas at Hira-Buddini, it is less than 1 ppm in both the samples. The spatially associated basalt analyzed 23 to 235 ppm tungsten, whereas granites and granodiorites have very low (<1 ppm) tungsten. Therefore, the source of tungsten in the felsic volcanics of Hutti area could be traced to metabasalt. The absence of significant amount of tungsten in the felsic volcanic of Hira-Buddini could be attributed to the lack of REE enrichment compared to REE in Hutti and Uti felsic volcanics.

Jan 1, 2007