Search Documents

By Daniel Saint Don, Jacques Dumouchel

QIT Madagascar Minerals (QMM)’s heavy mineral sand deposit located near the Village of Fort Dauphin, Madagascar was recently drilled using Boart Longyear Company’s Mini-Sonic drill. Continuous sand core samples were obtained to a depth of up to 30 meters for analysis and compared with the existing drilling data. Results were used as part of a validation process of the resource estimate, based on approximately 1,500 exploration holes drilled to date.

Jan 1, 2005

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameters like commodity price, mining or processing cost, stripping ratio etc. The most important characterization of these push backs is that the inner most push back has the highest value per ton, the second inner most push back has the second highest value per ton and so on. These nested pits are generated based on the best estimates of grade within a representation of the ore body in a three dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduced a new algorithm that incorporates ore grade uncertainty during push back design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence.

Jan 1, 2007

By F. Díaz-Fierros, D. Rubinos, M. T. Barral

The present work explores the reutilization of red mud, an industrial waste arising from the production of alumina, as a component of isolation technologies for hazardous substances. The work involved the study and optimisation of the geotechnical properties of red mud in conjunction with adsorption experiments of As(V) and Hg(II). The results from both types of experiments were integrated in a dispersion-diffusion model to calculate migration curves and minimum thickness of the red mud compacted layer. The geotechnical studies showed that compaction increased the stability and decreased the hydraulic conductivity of red mud barrier. Red mud sorbed high amounts of As (up to 44 mmmol kg-1) and Hg (up to 9.2 mmmol kg-1). The calculated minimum thickness of the red mud barrier was 1-10 cm for As and 2-19 cm for Hg, for an operation period of 35 years. The results obtained let to conclude that the reuse of red mud as a component of isolation systems of hazardous substances represents a viable alternative use of this residue.

Jan 1, 2011

By John Reilly

Costs of complex/underground projects have been consistently underestimated and delivery on time and on budget has been problematic. This has been attributed, to inadequate cost estimates and unidentified and/or insufficiently managed risk. Use of probabilistic cost estimates like the Washington State Department of Transportation?s CEVP® process (developed by the author and others) has produced more realistic cost estimates, explicitly identified and quantified risk (as input to risk management plans) and early awareness of key project issues. This paper updates previous work (NAT 2004), adds implementation detail for probalistic cost estimating as used by WSDOT, FHWA and other agencies and will address key issues in risk management, as related to probalistic cost estimates.

Jan 1, 2008

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By P. Cienfuegos, J. Loredo, J. J. Fernández, F. Pendás

This coal basin is a fore-deep basin with a lot of similarities with the Appalachian basin in the U.S.A., where throughout the 1990s, the research in coalbed methane grew rapidly due to a combination of factors, including the high prices for gas and electricity. In the Asturian Central Coal Basin 129 coal beds with thickness ranging from 0.8 to 1.5 m have been recognised in the productive carboniferous in an area bigger than 1500 km2. The maturation grade of these coals varies from the external zones of the basin where the volatile content ranges from 35%-40% to 20%-30%, to the internal zones of the basin where the volatile content ranges from 20% to 10%. In this context a sustainable exploration for fossil fuel is currently being undertaken in the most favourable areas of the basin in order to evaluate the real possibilities for coalbed methane (CBM) resources.

Jan 1, 2005

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By S. Constantinides

Over the past 100 years we have witnessed a revolution in permanent magnetic materials. Prior to 1932 electrical machinery depended upon steels for both the soft and the permanent magnet structures. Because permanent magnet steels were easily demagnetized, motors, generators, loudspeakers and similar devices often used the interaction between two electromagnets. Motors and generators were mostly of the induction type, depending for function upon induced fields. The discovery of Alnico in 1931 and its rapid commercialization presaged an expansion of the industrial revolution and today, permanent magnet structures are widely utilized. [ ] DEVELOPMENT OF PERMANENT MAGNETS Act 1: Early Days of Permanent Magnets Alnico, which stands for aluminum, nickel and cobalt, is a family of alloys with similar structure and processing requirements. Additional elements, such as copper and titanium, are present in minor amounts to optimize magnetic properties. Alnico is known by many trade names around the world including Alcomax, Hycomax, Ticonal, Nipermag, Koerzit, Oerstit, Nialco, etc(1,2,3). In addition to the generic name ?alnico?, it is usually appended with a number representing the magnetic grade.

Jan 1, 2011

By Z. A. Md-Nor

Risk management is an established loss-control methodology that has been applied successfully in many industries. Recently, interest in this structured approach has grown in the mining industry. The main objective of this research was to develop a risk-assessment process, which is a part of risk management, that can be used by the U.S. mining industry to more thoroughly characterize risks associated with haul truck-related fatalities. The assessment is based on historical data obtained from the U.S. Mine Safety and Health Administration (MSHA) investigation reports, which includes 113 fatal incidents that occurred from 1995 through 2006. The risk-assessment process used in this research involves the following basic steps: identification of the risks, risk analysis and risk evaluation. The preliminary hazard assessment (PHA) method is used in identifying and quantifying risks. Risk levels are then developed using a pre-established risk matrix that ranks them according to probability and severity. The resulting assigned risk value can then be used to prioritize control strategies. This paper is a part of a detailed study on risk assessment for equipment-related fatalities in mining sponsored by the Western U.S. Mining Safety and Health Training and Translation Center.

Jan 1, 2008

By Jean Habimana

The Detroit Upper Rouge Tunnel CSO Control Project will capture and store up to 201 MG of combined sewer overflow from 28 outfalls in Detroit, Dearborn Heights and Redford Township during wet-weather events. The history of rock tunneling in the area is associated with high groundwater inflows, artesian pressure, and hazardous and combustible gases. This paper presents the geotechnical considerations for designing the 11.28-km (7-mile) long, 9.14 m (30-ft) finished diameter tunnel and its associated adits, chambers and shafts, including the discussions of geotechnical investigations, rock mass characterization, estimated groundwater infiltration during construction, and the selections of excavation methods and lining system based on anticipated ground behavior to be encountered.

Jan 1, 2008

By Christian Maguire

The presence of hydrogen sulphide in sewerage systems leads to severe concrete corrosion. Acid causes breakdown of the concrete matrix, and attacks reinforcement. Older sewer systems under acid attack are often found to be acutely corroded, sometimes after short operational periods. Consequently secondary liners are now almost always used. Polymer concrete is extremely acid resistant and if used in segmental linings can forgo the need for a secondary lining. Combined with fibers and/or GFRP rebar Polymer Concrete can produce a very strong acid resistant lining, saving considerable time in the installation of additional liners. This paper explains the problems and advantages of using Polymer concrete in segmentaly lined wastewater tunnels, addressing areas of design, cost, and programming.

Jan 1, 2008

The efficiency of a coal mine ventilation circuit is usually measured by the ratio of the sum of the face quantities divided by the quantity supplied by the fans. Other types of systems use the power delivered to the power supplied to measure efficiency. This paper argues the case that the current measure may be inadequate and that by also looking at the power ratio, ventilation may be better managed. Problems associated with failing ventilation systems would be highlighted earlier so that crisis management could be avoided.

Jan 1, 2009

By Minerals and Materials Analysis Section

During 1996, US mines produced 319 t (10.26 million or) of gold metal valued at $4 billion. At yearend, mine reserves were estimated to be 4.7 kt (151 million oz) of gold metal. Almost all of the production was from western states. Nevada accounted for about 68% of national production. Information for this article was obtained through annual reports of mining companies, US Geological Survey (USGS) databases and other public sources. Table 1 shows production and reserves by mine. It divides the mines into two categories. These are producing mines whose primary product is gold, and producing mines for which gold is a byproduct or coproduct. The mines listed in Table 1 accounted for more than 98% of US gold production during 1996. Except the Daisy Mine, the table does not include mines that produced less than 31 kg/a (1,000 oz/year). The Daisy Mine started production in December of 1996. Nor does it contain mines whose byproduct concentrate is

Jan 1, 1997

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By B. Samoski

In late 1994, EPA and OSM acknowledged that efforts by any one agency or by the many different agencies to remedy the water quality impacts of decades of contamination from abandoned coal mine lands in Appalachia would not be successful if their disjointed efforts were not unified and if the local watershed organizations were not included. The result of the collaboration between EPA and OSM was the creation of a statement of mutual intent which was a pledge by government agencies, watershed organizations, and the industry to restore watersheds degraded by acid mine drainage from abandoned coal. The presenter will describe the evolution of this pledge from a paper promise to on-the-ground remediation projects.

Jan 1, 2002

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

By Xin Wang, He Shao, Wenpu Li, Yiyi Zheng, Xi Chen, Yurong Gao

This study utilized experimental and numerical simulation methods to investigate and analyze the atomization characteristics of three internal air–water mixed atomizers under different operating conditions. By comparing the research results, the effective dust control working parameters for the application of the selected atomizer in the engineering field were determined. Firstly, the atomization characteristics of the three atomizers were studied using a customized experimental system. The results indicated that nozzle 2 had a wide atomization range, a small atomization distance, and small droplet size; nozzle 3 had a narrow atomization range, large droplet size, and fast atomization speed; and nozzle 1 not only had a large atomization range but also could produce droplets of dry mist size with fast atomization speed, meeting the dust reduction requirements of the Majiliang Coal Preparation Plant. Secondly, Fluent software was used to simulate the atomization process and particle size distribution of the three internal mixed atomizers, determining the working conditions of the atomizers, the required number of atomizers, and the application angle of the atomizers in the internal mixed dust removal system. Finally, the atomized dust control system was applied on-site, achieving a total dust removal efficiency of 90.72% and a respirable dust removal efficiency of 89.75%.

Mar 9, 2024

By R. L. Zick, D. C. Finn

Introduction The high-density sludge process was originally developed by Bethlehem Steel Corp. for use on acid mine drainage (AMD) and diluted waste pickle liquor discharges requiring continuous chemical-treatment. This work began in the early 1970s and was first put into practical use around 1973. To date, there are approximately 15 operating systems that have been installed to treat mine drainage in the United States. In addition, there are another 10 systems installed outside of the United States. The dense-sludge process is an innovative and improved method for treating acidic metal-bearing streams in a manner that minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge-recycle process that forms particles with a low affinity for water. These particles are unlike conventional metal hydroxide solids that contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations that combine with calcium ions in lime-based treatment systems to form gypsum crystals. Compared to the form generated in conventional lime treatment systems, the physical form of the gypsum is radically altered when the dense-sludge process is utilized. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. The dense-sludge particles settle faster, dewater more readily, are more easily pumped and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered. In general, the conventional and dense-sludge treatment processes are very similar. The changes required to implement the dense-sludge process are minor, and, typically, much of the existing equipment can be utilized. The net results of the process are: reduced operational costs associated with sludge generation, improved process control (particularly pH control), reduced gypsum deposition (i.e., less scaling) on system components and reduced sludge generation resulting in less return water for treatment. Despite the relative simplicity of the process, the application of the technology requires careful discrimination, and the "experience factor" for implementation is an important consideration that should not be over looked.

Jan 1, 2000

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020