Search Documents

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By M. J. Sapko

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations) even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of current and future pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners? Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic, and safe mine sealing technique that can enable mines seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble in combination with a conventional mine seal so that the pressure resulting from a gas explosion is reflected, absorbed, and attenuated, so the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a ?Passive Mine Blast Attenuator? (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals. DISCLAIMER: This information is distributed solely for the purpose of pre-dissemination peer review under applicable information quality guidelines. It has not been formally disseminated by the National Institute for Occupational Safety and Health (NIOSH). It does not represent and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By A. Fisne

Outburst of gas, coal and rock can be defined as sudden release of coal and rock accompanied by large quantities of gas into the working face or other mine workings. The outburst events appeared rarely in some metal mines has generally occurred in salt and coal mines especially bituminous coal mining. The most important factors that influence the occurrence of outbursts are gassiness of the coal seam, tectonics, properties of the coal and rock and vertical and lateral stresses occurring in the seam and or rock or part of the coal seam. This paper describes the problem of gas and coal outbursts in underground coal mines. The outburst events occurred in Zonguldak Coal Basin located on the Black Sea coast was investigated since 1969. Geological and gas conditions of Zonguldak Coal Basin are described. The incidents are analyzed statistically with the criteria such as amount of coal and gas outburst, depth of workings, effect of tectonism, thickness and inclination of coal seams.

Jan 1, 2012

By A. W. Popp

After forty years of exploration and development, the heavy mineral sand deposits of the Murray Basin are on the eve of substantial exploitation by Iluka Resources Limited, Southern Titanium NL and RZM/Cable/Bemax, whom plan to initiate mining and processing operations in 2005. A trial mining and processing operation was undertaken on the Wemen North strandline deposit in 2001-2003 by Murray Basin Titanium, a joint venture of Sons of Gwalia and RZM/Cable, which brought to light a number of mining and processing problems which have since been the subject of extensive studies and process development work. The mineralogy of these weathered strandline deposits is complex by industry standards due to the variety of the heavy minerals present, coatings on the mineral grains and the extensive weathering and alteration which has taken place during the past 50 million years. This paper provides an overview of the complex mineralogy that, in turn, dictates the processes that can be used to recover the valuable heavy minerals. The Murray Basin encompasses some 300,000 km2 and has been a depositional basin, often land locked, since the start of the Cenezoic Era. The economic heavy minerals include ilmenite, altered ilmenite, leucoxene of highly variable composition, rutile, and zircon. There are also other heavy minerals present such as cassiterite, chromite, and monazite in quantities that pose both problems and opportunities. The clay content and overburden thickness also play a major role in the selection of the deposits to be mined. Project Services Consultants (PSC) has undertaken the preparation of this paper as part of its ongoing participation in the mineral sands industry and in particular the project development activities in the Murray Basin region currently being undertaken by Iluka Resources. PSC has been involved with the mineral sands business for several years with senior staff having in excess of 30 years global industry experience. The company is well placed to provide a range of services to clients like Iluka Resources in the areas of project development, execution and strategic development and industry advice.

Jan 1, 2005

By Ben Sosewitz

The subject of rapid excavation tunneling is one that is extremely important to the people in the Metropolitan area of Chicago. My personal observation is that it is also extremely important to the urban communities around the U.S., to many local and state governments, and to the public officials who are deeply concerned about state affairs and taxes. The Metropolitan Chicago area is in fact, (as are 40 other major urban areas in the U.S.) confronted at the present time with a very serious combined sewer overflow, drainage and pollution problem which accounts for an estimated 40% of the pollutional load on its waterway system. In response to this the District has to date spent some seven millions of dollars in an attempt to find the most economical solution available for the elimination of this problem. This study included extensive investigations of the geological strata, the quantity and quality of storm runoff to be dealt with, and the various methods of storage and treatment available. It has considered solving the overflow problem by a concept involving a series of tunnels, rock tunnels, shafts and storage areas which will collect, retain and subsequently treat that portion of the combined sewer overflow which can be handled in the most cost-effective and economical way, consistent with following the federal and state standards - with which we at the present time agree in principle.

Jan 1, 1997

By John J. Peregoy, James E. Downes

INTRODUCTION The U.S. Department of Energy's Waste Isolation Pilot Plant (WIPP) is being constructed to provide permanent storage of radioactive TRU waste materials emanating from military weapons production. These wastes are contaminated with radioactive elements heavier than uranium, thus the name trans-(or beyond) uranic (Uranium wastes). The WIPP site, which is located 26 miles east of Carlsbad, New Mexico, was chosen thru a selection process after the National Academy of Sciences recommended salt deposits as a promising host strata for the storage of radioactive wastes. Throughout the United States numerous DOE facilities have produced and stored defense-generated TRU wastes. Once WIPP becomes operational in the fall of 1989, all sites may ship directly to this repository. A companion project has developed special shipping containers (TRUPACT) for safe transport of materials to WIPP. The WIPP facility is currently composed of surface buildings, three shafts, and underground storage and experimental rooms and tunnels. Frontier-Kemper Constructors, Inc. (FKCI) has nearly completed the construction of the fourth shaft, an intake shaft, to provide additional ventilation to the underground workings. PLANNED SHAFT EXCAVATION METHOD Full-face raise boring ( upreaming ) was the allowable method selected by Frontier-Kemper Constructors for the excavation of the shaft. After arrival of an oil-field type rotary drill rig in December 1987, a 9 inch diameter pilot hole was drilled from the surface to the mine level, a depth of approximately 2145 feet.

Jan 1, 1989

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The industrial Internet of Things (IIoT)—a concept that combines sensor networks and control systems—has been employed in several industries to improve productivity and safety. NIOSH researchers are investigating IIoT applications to identify challenges of and potential solutions for transferability of IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40% of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system based on low-cost microcontroller Wi-Fi boards, to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine, and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communications and tracking infrastructure. INTRODUCTION The nation’s approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communications with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there currently exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT). IoT is the network of physical objects or ""things"" embedded with electronics, software, sensors, and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator, and/or other connected devices [1, 2]. It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: internet and things. The first one pushes towards a network-oriented vision, while the second tends to put the focus on generic objects. The traditional internet can be viewed as an internet of computers —i.e., “things” connected to the internet are computers only. IoT “extends” the internet by allowing other generic things that are commonly found in our daily life, such as refrigerators and cars, to be interconnected via the internet, and thus creates a bridge between the virtual word and the physical world."

Jan 1, 2017

By R. G. McLusky

This paper analyzes the opinion in Bragg v. Robertson, 72 F.Supp. 2d 642 (S.D. W.Va. 1999), a case which threatens the future of surface mining in West Virginia and which will almost certainly result in new policies or rules that will affect surface mining everywhere. This paper addresses: (1) the jurisdictional bases of the action which relies on the federal surface mining laws to enforce a state mining program; (2) settlement agreements reached in the case that threaten to alter federal policies beyond West Virginia borders; (3) a programmatic environmental impact statement on mountaintop mining being undertaken by the federal government; and (4) an opinion by the Court outlawing excess spoil disposal in intermittent and perennial streams.

Jan 1, 2001

By Tim O’Neil

What prompted the merger of the two long-established American Mining Congress/National Coal Association (AMC/NCA) groups that combine the coal, hard-rock, industrial- and agricultural-minerals sectors of mining? Both associations have been facing similar stresses for several years - structural changes in their respective industries, the changing personality and role of government and well-financed and organized opposition groups. In 1993, the AMC board of directors undertook efforts at reorganizing the association. One board member, who serves on both boards, suggested it might be time to give serious consideration to merging the organizations. This is an idea that had been discussed more or less informally at least three times during my tenure at NCA. Negotiations toward a merger began after that and were consummated in February of this year.

Jan 1, 1995

By Changjiang Li, Jun Yang, Qiang Fu, Xu Chang, Xing Wu, Yubing Gao

With the development of underground mining, the deformation of roadway floor has increasingly become a major constraint on the safe and efficient production of coal mines. To address the floor deformation that was caused by massive stress concentration in roadway, an innovative method based on deep-hole directional tensile blasting technology is put forward. By taking No.122108 working face in Caojiatan Coal Mine as engineering background and analyzing the mechanism of deformation, a numerical simulation and field test are carried out to verify the effect on deformation control of this technology. It is found that the deep-hole directional tensile blasting technology can actively control the fracture position of the roof in the gob area and cut off the stress transmission path, so as to relieve the stress in the roadway. And since different blasting parameters have different impacts on the stress relief effect, a numerical simulation is implemented and it is found that the stress relief effect is the best when blasting depth is set to be 32 m and the blasting angle be 60°. By applying the optimal blasting parameters to the field engineering test, it can be seen that the deep-hole directional tensile blasting technology could effectively reduce maximum stress value and stress field range of the both sides of the roadway, and make the stress field far away from the roadway, thus effectively controlling the deformation of the roadway floor. The deep-hole directional tensile blasting technology can effectively solve the problem of roadway floor deformation and can be safely applied to engineering sites.

Jun 13, 2023

By S. M. Jasinski

Peat is a natural organic material of botanical origin. Peatlands are situated predominately in shallow wetland areas of the Northern Hemisphere. Commercial deposits are formed from the gradual decomposition of plant matter under anaerobic conditions for about 5,000-years. In 2004, peat was harvested in 16 states. Florida, Michigan and Minnesota accounted for more than 80 percent of the U.S. production. Reed-sedge was the dominant variety of peat harvested in the United States, comprising almost 80 percent of the output. This was followed by humus, hypnum moss and sphagnum moss.

Jan 1, 2005

By F. S. Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors, lead to an understanding of the mechanisms causing roof problems. Factors such as unexpected rolls of the roof strata resulting in a gradual change from strong to weak roof; encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described. Strategies for overcoming these problems are discussed and detailed.

Jan 1, 2002

By William R. Yernberg

The combined 79th Annual Minnesota Section of SME Meeting and 67th Annual University of Minnesota Mining Symposium was held April 11 and 12, 2006, in Duluth, MN. About 300 mining professionals attended, including engineers, executives, mining managers and suppliers, from throughout the United States and Canada. This year’s theme was “Success in the New World of Mining.” The SME Minnesota Section meeting included a keynote session, a special projects update, a general managers update and technical paper presentations. The University of Minnesota Mining Symposium program featured a panel discussion on Minnesota’s relationship with China. The combined meeting included a trade-show consisting of 64 booth spaces. Tradeshow demand exceeded expectations, and an additional 10 booth spaces were added in the registration lobby. Also included were an SME short course on pump basics and social events.

Jan 1, 2006

By E. Arioglu

Discussion by E. Arioglu Y. Luo and S.S. Peng are to be congratulated for their outstanding paper providing new results from surface subsidence monitoring over longwall panels under different conditions. This writer found the authors' paper very interesting. In reference to this paper, the following contributions are offered: • In the paper, the maximum possible subsidence [(ASmax)] induced by chain pillar convergence has been related to a parameter (h/1- p) by linear regression. (Notations are expressed in this discussion's Fig. 1 (b).) It is a well-known fact that in a goaf the roof lowers onto broken material that gradually compacts. Then the physical behavior of goat may closely follow the compaction characteristics of broken materials. In light of this assumption, a mathematical means (Fig. 1(a)) of defining the expected compaction (i.e. surface subsidence) represents an exponential expression between [ASmax/m vs. h/1-p]. This is based on Luo and Peng's field observations from the Appalachian, Illinois and Alabama coal fields. (The coefficient of regression "r" under consideration was computed to be 0.883). • According to Wardell's (1969) findings for board and pillar mining, the maximum possible subsidence can be expressed in terms of maximum pillar loading (depth, ratio of extraction) and the height-to-width ratio of the pillars left. Using Luo and Peng's 1991 results, this writer discovered a regression equation between the above-mentioned factors. As displayed in Fig. 1(b), the functional expression approximates as closely as possible the observed subsidence data. It may be noted here that Wardell's approach (1969) can be successfully utilized for longwall panels having chain pillars. Reference Wardell, K., 1969, "Ground surface and control," Mining Congress Journal, January, pp. 1-7.

Jan 1, 1993

By R. D. Sharpe

Gypsum wallboard manufacturers in the United States shipped 3.18 billion m2 (34.2 billion sq ft) of wall-board products during 2004 versus 2.93 billion m2 (31.5billion sq ft) in 2003. Following a historic high production of gypsum wallboard products in 1999, production decreased in 2000. But it has steadily increased during2001 through 2004. Wallboard production in the United States increased about 8.6 percent in 2004 from 2003. Following several years of a “building boom” of new wallboard plants and the expansion of the manufacturing capacity of several existing plants, 2004 was a relatively quiet year. However, several new plants and capacity expansions were announced or are in progress during 2004.

Jan 1, 2005

By Marion Loomis

Environmental regulation is an ever growing cost to the mining industry. Requirements for such items as air quality modeling, hazardous waste disposal, selenium concentration in water and sagebrush planting consume more of the mining industry’s resources each year. The mining industry is willing to make the necessary financial commitments to assure that the air, land and water resources are adequately protected and restored. However, it is sometimes difficult to explain to management and stockholders why money should be spent on a specific issue when science and common sense indicate it is being wasted. Common sense and sound science should dictate how mining is regulated.

Jan 1, 1994

By L. A. Bakhvalov

According to the practice of mining management in the system of industrial complexes, the Kazakhstan gold mines are part of the mine processing industrial concerns providing ore-mining and ore-dressing. The cycle technology of winning operations used at the mining of vein deposits in the mines of the industrial concern is mainly provided by the systems of scrapping, scipping and electric locomotion. At present the information and computer system, elaborated on the basis of the Maikain underground mine is intended for creation of the system of automatic operation for the industrial complex mines. The information and computer system includes: - parametres characterising the accepted technology of works; - the main parametres characterising the technical devices of operation and control ; - information about the material, technical and personnel resources available at the mine; - mining and geological conditions of the deposit; - the facilities of the subsidiary units, of the mine; - the direct parametres and technico-economical indices in which the mine efficacy and activity is estimated. The suggested structure of the automatic operation system can be sensibly realized with the application of the microprocessor on the first level, the personal computer IBM PC/XT or PC/AT on the second level. For the complete realization of the project each mine will need 4-5 computers (as PC/XT), one IBM PC/AT and each mine complex - one super IBM for creation of the distributed information bank and its including in the integral world communication system.

Jan 1, 1992

By D. A. Peacock

"INTRODUCTION Outer space technology and exploration have reached a tipping point so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies, worldwide, are well on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3. The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars. How and why are the Moon and asteroids and their resources of interest to private space industry and companies? Why are the Moon and asteroids viewed as a potential business venue? GEOLOGY OF THE MOON AND ASTEROIDS –WHY DO WE WANT TO MINE THERE? Space enterprises are actively working towards establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products, and distribution of the products and services in space and to Earth and beyond2. Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water, and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind. The Moon regolith contains valuable rare earth minerals, platinum-group minerals (particularly where the Moon has been impacted by asteroids), volatiles (useful for processing and habitation), Helium-3 and titanium. Almost non-existent on earth, Helium-3 is abundant and accessible on the Moon and can be used in nuclear fusion power plants, producing much more energy than fission reactions and with much less radioactive waste. One of the main reasons Helium-3 is sought after as a fusion fuel is because there are no neutrons generated as a reaction product. Governments and private companies focus on mining of Helium-3 on the Moon as a basis for their economic models. Moon Express, one of the private companies who is planning on mining on the Moon, will recover moon rocks to fund its early operations25. Subsequently, it will recover Helium-3, platinum, and rare earth metals, as it engages in surface mining operations."

Jan 1, 2016

By Richard P. Graff

Author?s note: Diversity in practice exists in the application of Generally Accepted Accounting Principles (GAAP) for purchase price allocations with respect to the recognition of Value Beyond Proven and Probable Reserves or VBPP, as defined by the Emerging Issues Task Force (EITF) in EITF 04-3: ?Mining Assets: Impairment and Business Combinations?. This diversity appears to arise from differing interpretations of what constitutes sufficient information to value components of VBPP in business combinations. Concerned with this diversity in practice, respected members of the mining community formed a working group which prepared an issues paper that discussed this diversity and provided recommendations for recognition and valuation of VBPP in business combinations. The working group then submitted this paper to the EITF, requesting further guidance be issued on the concept of VBPP. In conjunction with the submission to the EITF, the working group also provided this paper to the United States Securities and Exchange Commission (SEC) for review and comment. The EITF discussed this issue at its May, 2008 agenda committee meeting. However, it declined to add this topic to the EITF agenda for further consideration. Absent additional guidance on VBPP from the EITF, the working group submitted a proposed definition of VBPP to the U.S. Securities and Exchange Commission for its consideration. The following article, which is consistent with the issues paper that was submitted to the EITF and the SEC, discusses the components of and valuation techniques for VBPP. The correspondence with the U.S. Securities and Exchange Commission, which includes the proposed definition of VBPP by the working group, is attached as Appendix 1 to this article.

Jan 1, 2008

By S. Janisko

Studies have linked long-term inhalation of diesel exhaust with adverse health effects such as cardiovascular disease, cardiopulmonary disease, and lung cancer. Diesel exhaust levels in underground mines can approach 100 times the environmental level and are therefore monitored closely in the mining industry. Elemental carbon (EC) (a product of diesel combustion commonly referred to as ?soot?) has proven to be a good indicator of diesel exhaust levels. The current procedure for measuring EC levels involves taking personal samples from a mine worker?s breathing zone and/or stationary samples in various parts of the mine and subsequently sending these samples to a lab for analysis by NIOSH 5040 method. Unfortunately, the whole process can take up to several weeks to complete. To address the problem of waiting weeks for results, NIOSH?s Pittsburgh Research Laboratory is developing a portable device for measuring levels of elemental carbon. This optical device takes a continuous sample of air in the surrounding environment and measures the absorbance of light passing through a filter that collects diesel exhaust particulates within the instrument. This technology can provide a near real time measurement of EC with accuracy within 10% error. The ability to take near real time measurements, combined with the instrument?s portability (currently small enough to be worn on a miner?s belt), makes this device extremely useful in the mining industry.

Jan 1, 2009