Search Documents

By B. Petri, N. Rouse

"Air overpressure monitoring procedures and instrumentation guidelines which apply to production blasting in underground limestone mining are not readily available. The industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground limestone mines. As such, there was no available background data from which the expected overpressure levels from production blasting in a new underground limestone mine could be predicted. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting in nearby production headings. To ensure the structures could withstand the blast-induced overpressure, a study was conducted to record empirical overpressure data and develop a model which could be used to control air overpressure levels by the production crews. This document describes the procedures used to develop the model, the development of the model, and the applicability of the model for predicting underground blast overpressures. INTRODUCTION A developing underground limestone mining operation required that a ventilation wall be built to house the permanent mine fans. At the time of the study, the mine was a single-level room and pillar operation with a 7.9 meter (26 ft) high roof, 13.7 meter (45 ft) wide entries, and 13.7 meter by 13.7 meter (45 ft by 45 ft) pillar dimensions. The mine is accessed via a 396 meter (1300 ft) long decline and 100 meter (330 ft) deep ventilation shaft. The ventilation wall was to be partially constructed of autoclaved aerated concrete blocks, for which dynamic strength data from explosives loading were unavailable. The company ownership feared that airblast may affect the wall due to the close proximity of the working faces. Therefore, the company management asked that the overpressure levels be estimated and compared with the designed wall strength. Few studies that apply to explosively-driven air overpressure levels in underground production blasting were found through a literature review. Therefore, the logical approach to assess the overpressure levels was to monitor the blast pressures at the site and conduct a thorough evaluation of the data. As a result of this study, the equipment setup and monitoring procedure used to record the airblast data is described. Finally, the experimental data gathered during the monitoring program is presented, trends and findings from the data are discussed, and recommendations for further study are presented."

Jan 1, 2015

By R. D. Doepker

The dissolution of metals from various metal-mine tailings has been studied through a series of submerged tailings batch tests at U.S. Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97 pct saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79 pct or 70 pct saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained nearly constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1990

By J. Mácsik, J. Lindblom, C. Maurice, Susanne Nigéus

Using non-hazardous industrial residues in mine waste remediation is beneficial not only for the mining industry where substantial amounts of the waste generated have potential to produce acid rock drainage and pollute the environment, but also the providing industry, minimizing the waste landfilled. In this study green liquor dregs (GLD), residue from 15 different paper mills were characterized to valorize it as a potential product as a cover material. In another part of the study, one of the GLDs and a local till were characterized to determine the optimal mixture of GLD amended till to be used in a field application at the closed Näsliden Mine in northern Sweden. The study concluded 10% GLD-amended till to be the optimal recipe and was successfully applied at the Näsliden mine waste dump. However, the great variability in the characteristics of GLD creates challenges if it is to be valorized as a product.

Dec 7, 2023

By T. K. Bundtzen, C. B. Green

Exploration expenditures in Alaska last year amounted to $8.9 million. This was comparable to 1985's $9.1 million. Development expenditures dropped 29%, $24.3 million in 1986 vs. $34.1 million in 1985. The exploration industry is restructuring and stabilizing after the loss of major mineral firms during the last few years. These included Anaconda Minerals, Asarco, Hecla Mining, Enserch Exploration, Phillips Minerals Division, Exxon Minerals, Noranda Inc., General Crude, Mohawk Oil & Gas, Inspiration Development, Teton Exploration, and St. Joe Minerals Division. Some of these companies were mineral subsidiaries of oil companies and were either dissolved or redirected to programs outside of Alaska. However, recent entry exploration firms include Echo Bay Mines Ltd., Long Lac Minerals, and Exvenco. They are busy evaluating prospects and mineral developments in the southeastern panhandle. In the 1970s, about $254 million was spent on Alaska mineral exploration. Of this, about 5% ($12 million) was for nonmetallics and coal, about 26% was directed at precious metals ($66 million) mainly gold, and 69% ($175.3 million) for the base metals zinc, copper, molybdenum, tin, tungsten, and nickel. Since the early 1980s, trends have reversed. Of the nearly $196.3 million spent from 1981-1986, 48% has been for precious metals ($94.3 million) and 40% on nonmetallics and coal. In the last two years, nearly 70% of the Alaskan exploration dollar has been spent in search of precious metals. Three gold skarns were explored during the year - the Nixon Fork project in western Alaska (Battle Mountain Mining Co.), the Nebesna and Rambler lodes of the northern Wrangell Mountains (Nebesna Mining Partners), and the Zackley project near Paxson in southcentral Alaska (Nerco Minerals). Nearly 7.6 km (25,000 ft) of diamond and rotary drilling were conducted on these three properties. Aspen Exploration announced that significant gold mineralization was found under the Nome coastal plain in western Alaska. Meridian Minerals joint ventured with Resource Associates of Alaska, exploring precious metal

Jan 5, 1987

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Changshou Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,175 t (3,500 st) of ore per day with an average gold grade of 12.6 g/t (0.4 opst). The mine has a large horizontal extent of 762 by 152 m (2,500 by 500 ft) and a vertical extent of 6 to 61 m (20 to 200 ft). Based on the characteristics of the ore bodies, the deposits are divided into several mining zones. The geotechnical properties of mining zones are also different from one zone to another. A successful geotechnical collection system is very important for mining design and operation in the Leeville underground mine. Three methods are used to collect the geotechnical data in the Leeville underground mine: • Core logging. Most geotechnical data are collected by this method, which is based on exploratory drills and estimates parameters for rock quality designation (RQD), fracture frequency (FF), compressive strength and rock mass rate (RMR). • Site investigation. This method collects more detailed geotechnical data and geostructural data from work done in the underground drifts and stopes. Parameters of RQD, FF, compressive strength, RMR, rock tunneling quality index (Q) and geostructural data are estimated. • Data collected from drill holes made for the critical infrastructure facilities. This method provides the best detailed geotechnical information for areas in which the critical infrastructure located. A complete geotechnical database has been constructed using this geotechnical data collection system. The database can be used for the design of ground support, stopes and stope blasts, among other critical applications.

Jan 1, 2010

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

By R. Mensah-Biney

The adsorption of gold-thiourea complex onto a cation exchange resin, Amberlite 252, has been evaluated in a batch stirred reactor. The observed non equilibrium saturation capacity was 3.20 meg Au/g dry resin (620 kg/t) whereas the equilibrium ion exchange capacity was only 0.53 meq/g (103 kg/t). The enthalpy of adsorption was 4 -25 kJ/mole under equilibrium conditions and increased to 20-200 kJ/mole under non equilibrium conditions. Under non equilibrium conditions, the adsorption capacity of the resin decreased with increasing temperature and increasing thiourea concentration and increased with increasing gold concentration. This dependence of adsorption capacity on thiourea concentration and temperature may be a useful tool for elution of gold from the loaded resin. Scanning electron microscopy revealed evidence of deposition of elemental gold on the loaded resin under non equilibrium conditions. The proposed mechanism for "adsorption" of gold-thiourea complex onto this cation exchange resin consists of an ion exchange reaction followed by a reduction of the exchanged gold complex to elemental gold on the surface of the resin.

Jan 1, 1997

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By Keith A. Heasley

Historically, the surface subsidence over underground coal mines has been predicted using empirical profile or influence functions which have little or no connection to the actual mechanics of the subsidence. Without a mechanistic basis, establishing the exact site-specific parameters to use in these empirical methods has been problematic. A practical subsidence predictive method based on mechanics has the appealing capability of allowing the determination of site-specific parameters from fundamental properties of the overburden with minimal field calibration work. This paper presents several case studies where a mechanics-based, boundary-element program is used to back-calculate the surface subsidence associated with various panels at several Northern Appalachian coal mines. The program used in this case study is called LAMODEL, and it incorporates a frictionless, laminated overburden into a general purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin scam or vein type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from the case studies in this paper demonstrate that the laminated model with calibrated properties can easily provide moderately accurate subsidence predictions and is fairly flexible for fitting measured subsidence. However, additional subsidence predictive case studies arc recommended in order to ultimately evaluate the potential of the laminated overburden model for practical subsidence prediction

Jan 1, 1999

By Frank M. Howell

Creede, one of the younger major mining camps in Colorado, grew spectacularly to a town of eight or ten thousand people in the early 1890's following discovery of rich ore in the Amethyst and Last Chance mines. Gross metal production in gold, silver, lead, copper and zinc rose to a maximum of four million dollars a year in 1893. Annual production dropped to much lower figures and ranged between one hundred and five hundred thousand dollars per year during the period from 1914 to 1940. Production reached a gross of eight hundred thousand to one million dollars per year by the mid-1950's. In the years 1953 to 1957, Steven and Ratté conducted geologic investigations which were carried on as part of a cooperative program of the U. S. Geological Survey and the Colorado Metal Mining Fund Board. In a preliminary report on the Creede District, Steven and Ratté suggested that the Bulldog Mountain Fault Zone appeared to be a favorable structure to prospect. On the basis of that recommendation, augmented by independent work done by Manning W. Cox, the property was acquired, transferred to Bulldog Mountain, Inc. and financed by an O. M. E. loan. Late in 1963 Homestake Mining Company, under a Lease and Option Agreement, backed the venture by furnishing additional funds plus management.

Jan 1, 1969

By I. J. Wu

China’s land area, comparable in size to United States or Canada, contains diverse geological environments and mineral resource potential. The diversity in geological environments is such that the potential for developing many world-class mineral deposits in China is good. However, China’s mining sector was not open to foreign investment until the1990s. The long-term prospect for Chinese resource development is attractive because of China’s enormous population and cumulative demand for minerals. Approximately 33 foreign mineral companies, including 11 major internationals, are to various degrees active in China. Chinese mining laws and regulations pertaining to joint ventures with foreign companies are, from the international investment prospective, evolving slowly, but positively. This positive trend is continuing under the current government reform process, which is moving China towards a freer market economy. Although improving the enforcement of relevant laws and regulations is an ongoing process, the environment for mineral investment and joint ventures is increasingly more accommodating to foreign companies.

Jan 1, 2000

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

Operators of mining vehicles are exposed to high levels of whole-body vibration (WBV) and are therefore at risk of developing vibration-related health disorders. For implementing an effective control strategy, it is imperative to locate the source(s) of vibration, and the specific changes that might occur to the vibration signals during its transmission through the seats to the recipient human body. With this objective, Seat Effective Amplitude Transmissibility (SEAT) values of seat modules used in dumpers (n = 10) and other heavy earth-moving machines (n = 11) were evaluated in an iron ore mine. Vibration was measured simultaneously on the seat and on the cabin floor beneath the seat using tri-axial and uni-axial accelerometers. The study aims at determining the quality of seat modules of the transport and non-transport vehicles from the perspective of their natural resonance frequencies and capability of any such seat in reducing harmful vibration. The highest acceleration values were observed in the z-axis for all the dumpers. SEATrms values ranged from 78 to 133% and SEATvdv values ranged from 72 to 130% for the dumpers. For other HEMMs, SEATrms values ranged from 55 to 125% and SEATvdv values ranged from 56 to 123%. Mechanical vibration contains multiple frequency components. To understand the changes taking place to the different signals at these frequencies, 1/3 octave band analysis was carried out for the signals recorded both on the seat and the floor. There was significant attenuation (38 to 57%) at 4 Hz for three Dumper seats, whereas they resonated in the range of 1.6–2.5 Hz. The transmissibility(%) in the resonating frequencies ranged from 108 to 156%. Resonance frequencies for the remaining seven dumpers ranged from 3 to 8 Hz. The spine has been reported to resonate at 4 Hz, whereas resonance at 1.6 Hz has little significance to human beings in regard to WBV of a seated person. Hence, the characteristic resonant frequency of 4 Hz of seats as observed in the present study has the potential of causing adverse impacts on spinal health. Evaluation of SEAT factors and resonance characteristics of seats are therefore recommended to be examined while selecting a mining vehicle for regular deployment in mines.

Mar 12, 2021

By William Gleason

"Sluggish prices for commodities and a glut of oversupply of many commodities did not stop the world’s largest mining equipment makers from showing off their latest and greatest machines and technology starting with the world’s largest equipment trade show, bauma 2016 in Munich, Germany.From April 8-14, an estimated 580,000 visitors from 200 countries visited the show that featured 3,423 exhibitors from 58 countries. While primarily a show for construction equipment, the mining footprint has grown over the years. Among the largest exhibits was that of Liebherr, which brought more than 100 products, had an outdoor exhibition stand, a stand for the components division and a career stand under the motto “Be Part of Something Bigger.” One of the biggest aspects of the exhibit was its mining products where the company staged the first-ever professional table tennis match in the 130 m3 (170 cu yd) dump body of the T 264 mining truck. The top German players Timo Boll and Patrick Franziska with their trainer Jörg Robkopf faced Austria’s singles world champion from 2003, Werner Schlager, and the reigning Team Europe champions Chen Weixing and Stefan Fegerl.“Bauma 2016 was an absolute success for Liebherr. With this year’s appearance we were once again able to show our innovative strength, performance and technological diversity to a very large and international audience from the industry. We conducted interesting discussions with numerous customers and partners from various countries and discussed new projects,” said Stefan Heissler, Member of the board of directors of the Liebherr Group.Likewise, Caterpillar, the world’s largest maker of construction and mining equipment had a large presence at the show with more than 60 products and 12,000 m2 (129,000 sq ft)of exhibit space. Among the iconic yellow mining equipment that was on display was the 6015B hydraulic mining shovel."

Jun 1, 2016

By K. S. Whiting

Elevated concentrations of copper, cobalt, and arsenic within the Panther Creek Basin sediments in north central Idaho prompted an evaluation of the sources of the metals. Potential tailings and waste rock source samples collected at the head of Blackbird Creek were compared to sediment samples in the Panther Creek Basin using electron microprobe techniques. The mineral types, degree of alteration, and the morphology of the metal-bearing sediment grains within Blackbird and Panther Creeks were found to consist of copper-, cobalt-, and arsenic-bearing sulfide minerals.

Jan 1, 1997

By Will B. Jamison

The most serious safety problems encountered in U. S. underground coal mines today are related to the roof bolting operation. Also, roof bolting is usually the operation which limits coal production of the section. The purpose of my paper is to review some of the research, developments, and new ideas related to roof bolting. Many of these ideas have originated at. coal mines or with manufacturers. Most of the research on fundamental improvements has been funded by, and is a part of, the excellent and broad plans of the Bureau of Mines.

Jan 1, 1977

By S. P. Sandoval

In 2002 the Freeport-McMoRan Technology Center undertook research to develop a lower-cost alternative to guar for cathode smoothing in copper electrowinning. The work was conducted at the Technology Center?s SXEW Test Facility located in Morenci, Arizona. Bench-scale copper electrowinning cells were designed and implemented to screen a number of potential polymers for cathode smoothing. These included modified polysaccharide polymers that were nonionic, cationic, and anionic in nature.

Jan 1, 2010

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.