Search Documents

By Wang Ding-heng, Wang Zhi-yuan, Nolan B. Aughenbaugh

The People's Republic of China has abundant coal resources with proven reserves amounting to 582 Gt (641 billion st). Recognizing coal as a major energy source on which to build the country's industrial and economic base, there has been a rapid increase in production since the founding of the People's Republic. In 1949, only 29.4 Mt (32.4 million st) of coal was mined. Production has increased to 576.5 Mt (635.5 million st), exclusive of Taiwan, at present, making China the third largest coal producing country in the world. Plans call for a 4-5% increase in annual production for the next 20 years. Coal constitutes 70% of the primary energy consumption in China. The remaining 30% is divided between petroleum and natural gas with 26% and hydropower with 4%. Coal use and consumption is divided as follows. General industrial use comprised 48.9%, power generation uses 20.1%, and coking accounts for 10.5% (6.3% for metallurgy and 4.2% for chemical industry). Domestic use such as home heating and cooking makes up 17.8% and coal-fired steam engines for railways uses 4.7%. Coal Districts Coal underlies about 1/18 of China's land area. It occurs in 30 provinces, autonomous regions, and municipalities. In addition, the western interior region, which has not been explored, may contain sizable reserves. Based on geology, geography, and administration, the coal fields can be grouped into five districts as shown in Fig. 1. The north China district, the heart of the industrial base for the country, has the most extensive and largest deposits of the five districts. This amounts to almost 40% of the country's total reserves. The largest coal basin with proven reserves of 181.4 Gt (200 billion st) and the most exploitable seams is located some 300 km (186 miles) southwest of Beijing (Peking) in Shanxi Province. Centered around Taiyuan, the compound field extends from Datong in the north to Xian in the south. Its western extension is not known fully. The Northwest and Northeast districts contain the second and third largest deposits. The biggest coal field in South China is located in the Sichuan and Guizhou Provinces near Chongqing. At present, it is not known if sizable coal measures exist in the Tibetan district. Coal Types China's coal varies widely both in age and rank. Geologically, coal measures were deposited from the lower Carboniferous (Pennsylvanian of the US) and Permian of late Paleozoic, mainly during the Jurassic of the Mesozoic and peri¬odically throughout the Cenozoic. Collectively, coal from the lower Carboniferous, Permian, and Ju-

Jan 3, 1983

By Joseph W. Murray

GENERAL DESCRIPTION The undercut-and-fill method of mining was devel¬oped by Inco Ltd. in the Sudbury district of Ontario, Canada, to deal with abnormal ground conditions en¬countered in pillar recovery. Although it is now some¬times utilized as a primary stoping method, the main application continues to be in pillar recovery. In any mining method in which fill is employed, pillar systems tend to fail gradually as stoping pro¬gresses. As a result, most pillars are completely destressed and broken by the time pillar recovery com¬mences. Control of the back in such ground becomes a major problem and is contingent on local conditions as they exist in the workplace. In most mining methods, operations such as drilling, blasting, slushing, and tim¬bering can be readily assessed and the mining cycle pre¬dicted. However, in the mining of pillars with overhand methods, the time and effort required to maintain a safe back varies to a quite unpredictable extent. For years the square-set method was the most effective means available for pillar recovery. However, in areas where bad ground was encountered, square setting was a costly and sometimes hazardous method. As the tonnage mined from pillars increased, it was apparent that a safer and less expensive approach was required. Past experience indicated that the best way to deal with broken ground was to mine from the top down. Top slicing systems were examined but were rejected due to the major sub¬sidence which resulted. However, ideas generated from studying top slicing finally developed into the present method of undercut-and-fill. This method, which has almost completely replaced square-set mining, exhibits reduced costs, has improved safety and efficiency, elimi¬nates the factor of bad ground overhead, and allows a closer prediction of the actual mining cycle. The result is more accurate scheduling of pillar production. This factor is of increasing importance as the tonnage from pillar recovery increases in relation to total mine pro¬duction. Undercut-and-fill is a method of extracting a block of ore by mining successive cuts, working from the top down. After a cut of ore is completely mined out, lami¬nated timber stringers are constructed along the sides for the full length of the cut. Round logs covered by a wire screen are laid across the stringers to form a mat. The cut is then tightly filled with hydraulically placed cemented sand fill. Mining is then resumed on the cut immediately below the mat. As the cut advances, the timber stringers are supported by round timber posts seated on the solid bottom of the cut. Drilling, blasting, muck removal, and timbering operations are repeated until all the ore in the cut has been removed. At this time, another log mat is laid and the cut is filled. This sequence is continued until the block has been mined from level to level. The basic principles of undercut-and-fill can be adapted to a variety of mining situations. It can be applied transversely or longitudinally in ore bodies of varying width, that dip from vertical to flat lying. The method can be applied using conventional equipment or it can be mechanized through the introduction of small diesel or air-powered units for muck removal. Undercut¬and-fill is a selective method, ore recovery is high, and dilution can be controlled to an acceptable level. How¬ever, it is a high-cost, labor-intensive method and as such its use is restricted to areas where the less costly meth¬ods of ground support are not successful or where bulk mining methods are not adaptable. One basic require¬ment for undercut-and-fill is an adequate source of hydraulically placed cemented sand fill and a dependable sand plant and distribution system. The success of the undercut method is to a large degree dependent on the competence of the fill placed in each of the successive cuts. In theory, the weight of the fill on each cut is supported in part by the cemented sand itself as it binds to the rough sides of the mined¬out areas next to the pillar walls, and in part by the tim¬ber support. As mining progresses beneath the mat, a downward pressure is exerted within the cemented fill and a voussoir arch develops above the mat, across the full width of the cut. This supports the major portion of the load. The log mat and posts have a double func¬tion in that they carry the remaining weight not sup¬ported by the voussoir arch and in addition prevent any pronounced settling of the fill mass. Excessive settling breaks the bond between the cemented fill and the pillar walls, eliminating the arch effect and transferring the entire load to the mat and posts. The theory of a voussoir arch forming within the cemented sand fill mass is substantiated in practice by the fact that pillars have been mined from level to level with no more significant weight on the bottom cuts than was experienced on the top cuts. In effect, as mining progresses downward, there is no additional transfer of weight from previous cuts to the cut being mined. APPLICATION OF UNDERCUT-AND-FILL Because of their size, the Sudbury ore bodies are, for the most part, mined transversely and, to a considerable extent, by filling methods. Transverse stoping blocks are designed with 9-m (30-ft) crown pillars established be¬low each level and with stopes separated by vertical rib pillars. In past years, floor pillars were left above the level as well, but present practice favors the silling of primary stopes at the base of the rail. Rib pillars are designed to meet the ground control requirements of the primary stoping methods. Local conditions and past experience generally dictate their size. Historically, since the square-set method was to be used for recovery, rib pillars were designed to accommo¬date standard 1.7-m (5'h-ft) sets. A typical rib pillar is four sets wide [6.7 m (22 ft)] when located between two square-set or cut-and-fill stopes having a width of 8.4 m (27.5 ft). When the undercut-and-fill method was de¬veloped, a mat width of two sets was adopted. This di¬vided each cut of the common four-set pillar into two

Jan 1, 1982

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

By Jeff Mattern

"Slope performance monitoring, dependable operational practices and ongoing collection of geologic data in openpit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike openpit has been ongoing since the early 1980s, having its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls.While technology can be efficient, interesting for collecting needed data, slope design fundamentals based on that data can be applied to create much added value.With the proper available equipment, steepening of bench face angles via presplit blasting is not an uncommon method for steepening of interramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted, resulting in quantified, rock-specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2° on a 305- m (1,000-ft) high slope, without the necessary purchases and procedural changes that would be required for presplit drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves.LocationThe Goldstrike openpit is located in the Great Basin, on the northern end of the Carlin Trend gold belt in northeastern Nevada (Fig. 1). The mine has produced more than 1.2 kt (43 million oz) of gold during the past 30 years."

Dec 1, 2018

By S. Dubnewych, S. Kieffer, M. T. McRae, R. R. Redd

The seismic vulnerability of the existing outlet tower at Lake Mathews reservoir, located in Riverside County, California, necessitated the design of a new outlet facility to assure serviceability of the facility following a major earthquake. The components of the proposed facility include: a new outlet tower; a shaft; a new outlet tunnel; an approach channel that will be excavated underwater; and two short tunnels that will connect the new outlet tunnel to the existing outlet tunnel via the shaft. As the new facilities will be constructed while the reservoir is in operation, a cofferdam will be constructed around the site of the new outlet tower. The design for the underground facilities used a combination of empirical methods; limit equilibrium analyses, including displacement-based pseudo-static analyses for dynamic loading conditions; and numerical analyses. This paper outlines the design methodology used to develop an innovative design for the facilities which can be constructed within the time frame required by the operational schedule of the reservoir and existing outlet facility.

Jan 1, 1999

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012

By David R. Maneval

The mining of coal in Alaska receives special treatment in the Surface Mining and Reclamation Act passed by the U.S. Congress in 1977 (PL95-87). Section 708 of the Act required that the National Academy of Sciences (NAS) perform a study of "Surface Coal Mining Conditions in the State of Alaska, In Order to Determine Which, If Any, of the Provisions of the Act Should be Modified with respect to Surface Coal Mining Operations in Alaska'. The special committee on Alaskan Coal Mining and Reclamation of NAS completed their study in 1980 and prepared their report (NAS, 1980). At this time, the Secretary of the Interior and the Congress have taken no special action with regard to either special regulations geared specifically to Alaska or to submitting special draft legislation to the Congress requesting amendment of PL95-87. The Alaska Department of Natural Resources (DNR) has drafted legislation which was submitted to and passed by the 1982 session of the State Legislature. The State regulatory agency has also drafted the requisite regulations necessitated by the amendments to the State's Basic Coal Mining Act. It is expected that by mid 1983 DNR will have applied for "primacy" to the office of Surface Mining, U.S. Department of the Interior (OSM). They will be submitting the amended State Law, the revised State Regulations and an operational plan as called for by OSM regulations. The presumption is that primacy will be granted to the State of Alaska under PL95-87. The Usibelli Coal Mine continues to be the only operational commercial mine for coal in the State of Alaska. It produced 7.26 x 10 kg (8 x 10 " T) of coal during 1981. The current mine was started in 1920 by Captain Lathrop, an early developer and pioneer in Alaska. It was continued by Emil Usibelli and was taken over after the death of E. Usibelli (in the 1964 earthquake) by his son Joseph Usibelli who is the current President of, the firm3 Their latest improvement is a 27.5 m (36 yd. )Bucyrus-Erie Dragline which handles most of the overburden removal. The coal is removed by a loader-truck combination. They are currently starting up the use of a unit train loading facility which handles forty cars every two hours. This loading system was a development necessitated by the Sun Eel Export contract. The Alaskan Railroad was a major cooperator in the development of the first unit train loading facility in Alaska.

Jan 1, 1982

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open-pit and underground mines of all sizes are regularly collecting point cloud data as laser scanning (LiDAR) and photogrammetry surveying devices have become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely and safely, rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing. This article specifically focuses on digital outcrop modeling and digital terrain engineering. Point clouds. The high-resolution and increasing availability of point cloud technology is rapidly improving open-pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations and typically the reflective intensity and/or the visible three-band color of each point (Fig. 1).LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device.Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles and even in a mobile backpack shown in Fig. 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds,” but this article does not address these due to their higher cost and lower versatility and mobility."

May 1, 2016

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

This study investigates the changes in seismic velocity of rockmass before and after three major seismic events to determine any potential identifiable precursory velocity changes associated with these events. Induced stress measurement is one of the challenging tasks in deep underground mining, with extreme impacts on the safety and stability of the mine. This study used p-wave passive seismic tomography to image the velocity redistribution within a rockmass, which can indicate induced stress level changes in the rockmass and detect the velocity changes that might precede a major seismic event or a rockburst. The ultimate goal of this research focus is to develop another tool for the deep-mining community that will help to increase safety and efficiency. For this purpose, the hypothesis of conventional mechanics, which implies induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs, is evaluated. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring; however, the p-wave velocity did increase in the closest “zone center” for two of the three events. 

By JUAN DIAZ, Kray Luxbacher, Steven Schafrik, Dionissios T. Hristopulos, Zach Agioutantis

Methane gas is emitted during both underground and surface coal mining. Underground coal mines need to monitor methane gas emissions to ensure adequate ventilation is provided to guarantee that methane concentrations remain low under different production and environmental conditions. Prediction of methane concentrations in underground mines can also contribute towards the successful management of methane gas emissions. The main objective of this research is to develop a forecasting methodology for methane gas emissions based on time series analysis. Methane time series data were retrieved from atmospheric monitoring systems (AMS) of three underground coal mines in the USA. The AMS data were stored and pre-processed using an Atmospheric Monitoring Analysis and Database Management system. Furthermore, different statistical dependence measures such as cross-correlation, autocorrelation, cross-covariance, and variograms were implemented to investigate the potential autocorrelations of methane gas as well as its association with auxiliary variables (barometric pressure and coal production). The autoregressive integrated moving average (ARIMA) time series model which is based on auto-correlations of the methane gas is investigated. It is established that ARIMA used in the one-step-ahead forecasting mode provides accurate estimates that match the direction (increase/decrease) of the methane gas emission data.

Aug 2, 2022

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By Mark J. Zdunczyk

"Frac sand is industrial silica sand much like glass, foundry, filtration and blast sand. The sand must meet certain specifications set forth by the industry that consumes the product. The production and consumption of frac sand has experienced record growth in the last 10 years because of new oil and gas drilling, new horizontal well drilling, multi-stage fracturing and the stimulation of older wells that have little or no production. Frac sand is needed to “prop open” the fractures in the rock reservoirs to allow oil and gas to flow out more freely.According to the U.S. Geological Survey (USGS), the estimated production of frac sand in 2015 was 71 percent of the total production of industrial silica sand or 67.4 Mt (74.3 million st). This is a decrease of about 12 percent from 2014. However, the silica sand industry and other industry sources estimate only 50 Mt (55 million st) of frac sand were produced in 2015. In recent years both the USGS and industry studies have been very close in estimating the production of frac sand but with the recent downturn in frac sand production, perhaps, reporting to the USGS was not as accurate. These discrepancies may be that the USGS statistics are based on voluntary reporting by the industry and some companies report their approximate production, others may not. It is always difficult to obtain accurate production figures of any industrial mineral or construction aggregate operation as most companies tend to keep those figures somewhat confidential. It is certainly accurate to report that the production of frac sand had decreased since the last quarter of 2014 and through 2015. The oversupply of oil and natural gas has led to this decline in frac sand usage. Oversupply has idled drilling rigs and well completion activities. World Oil Magazine reports that 2015 was the worst year for rigs in a quarter century. The only wells being completed are those that have contract agreements to do so, others have been capped. Very few new wells are being drilled. Since about 98 percent of well completion is sand and water, the sand supply has caught up with the demand. There are some bright spots in the “oil patch” as the Permian Basin in Texas and the Woodford Shale in Oklahoma have kept pace somewhat with drilling and completion. It has been reported that the frac sand producers in the Brady-Voca, TX area are producing to nearly capacity. The northern frac sand producers like those in Wisconsin, Illinois and Minnesota are feeling the downturn because of the cost of shipping sand to these moderately active basins and plays. The “rule of thumb” is that freight is 2/3 and sand is 1/3 the cost."

Jul 1, 2016

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By A. K. Raina

Blast induced damage to the final wall of rockmass in any civil or engineering application is a major concern to the rock excavation engineers. There are at least four distinct techniques practised by blasting engineers to minimise the damage to the parent rock during blasting that are classified as contour blasting. One of the methods to achieve a smooth wall or rock surface in blasting is pre-splitting, where blastholes in the final row are mildly loaded with explosives and fired first in sequence before the rest of the holes in a round of blast to achieve a split in rockmass. Since blasting is one of the most adopted methods for achieving a final wall in a desired shape, while maintaining the rockmass integrity, the design of pre-split blast assumes importance. There are several variables that determine the final shape of the pre-split face including the rock type, the drill diameter, the explosive characteristics, the orientation of major joints with respect to drill hole, the linear charge density, the spacing of drill holes and inclination of the drill holes. This study attempts to determine the importance and sensitivity of variables in pre-split blasting using historical data from open excavations of a hydroelectric project in India. Keeping in view the multitude of variables, low correlation of independent variables with responses and high level of interactions between the variables that define the blast results, it was found suitable to use ANN to determine the importance and sensitivity of the variables involved. A new method to determine the blast induced damage to rockmass, namely, undamaged area (AUD%), is introduced. Half Cast Factor (HCF%) and AUD%were calculated for a high wall and trenches by digital image analysis technique using the Fragalyst software. Joint spacing and linear charge density emerged as most controlling variables in determining the final result of pre-blast. The relative importance of other variables assuming significance in the case of both the designed outputs is also discussed. A comparative analysis of HCF%and AUD%on the basis of results obtained from ANN analysis is also presented. A futuristic approach concept has also been introduced.

May 30, 2021

By J. W. Furlan

Due to the time consuming nature of froth testing in a laboratory environment, it is required, due to practical limitations, to develop a method of applying a single set of performance test data (Visintainer & Whitlock, 2012) obtained for a single froth pump at a given speed, to a range of froth pump speeds and sizes, % air contents, and liquid viscosities. Head, efficiency, and flow all vary as functions of both liquid viscosity and air content. As such, it is necessary to develop a technique which can be used to interpolate from existing test data in order to predict froth pump performance for pumps of various sizes running at variable speeds. Details of the technique developed in order to achieve this goal as well as the insights gained from analysis of the resulting regressions are discussed. Additionally, comparisons are made between the performance predictions of this test-derived method and those of the Hydraulic Institute Standard for the effects of liquid viscosity on centrifugal pump performance (ANSI/HI 9.6.7-2010).

Feb 27, 2013

By S. L. Ducummon

Inactive underground mines now provide essential habitat for more than half of North America's 44 bat species, including some of the largest remaining populations. Thousands of abandoned mines have already been closed or are slated for safety closures, and many are destroyed during renewed mining in historic districts. The available evidence suggests that millions of bats have already been lost due to these closures. Bats are primary predators of night-flying insects that cost American farmers and foresters billions of dollars annually, therefore, threats to bat survival are cause for serious concern. Fortunately, mine closure methods exist that protect both bats and humans. Bat Conservation International (BCI) and the USDI-Bureau of Land Management founded the North American Bats and Mines Project to provide national leadership and coordination to minimize the loss of mine-roosting bats. This partnership has involved federal and state mine-land and wildlife managers and the mining industry. BCI has trained hundreds of mine-land and wildlife managers nationwide in mine assessment techniques for bats and bat-compatible closure methods, published technical information on bats and mine-land management, presented papers on bats and mines at national mining and wildlife conferences, and collaborated with numerous federal, state, and private partners to protect some of the most important mine-roosting bat populations. Our new mining industry initiative, Mining for Habitat, is designed to develop bat habitat conservation and enhancement plans for active mining operations. It includes the creation of cost-effective artificial underground bat roosts using surplus mining materials such as old mine-truck tires and culverts buried beneath waste rock.

Jan 1, 1997

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semigelatin dynamites, three slurry explosives and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): NO, 0.010-0.035; NO2, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1979

By C. Xiao, R. Chi

In recent years, the biosolubilization of rock phosphates by phosphate-solubilizing microorganisms has become a major topic of research studies. However, the microorganisms used in previous studies were mostly single and known species, and studies seldom focused on mixed communities of microorganisms or microbial consortia from natural environments. In this study, a microbial consortium from rhizospheric soil was used to solubilize two different compositions of medium- to low-grade rock phosphates — designated as ore samples 1 and 2 — in a laboratory-scale bioreactor. The microbial consortium showed good growth in the bioreactor, reduced the suspension pH and released soluble phosphates from the ores. Scanning electron microscopy with energy-dispersive X-ray spectroscopy showed the action of the microbial consortium on the ore surface. There was considerable corrosion on the ore surface, and 3.42 and 4.93 percent of the element phosphorus was removed from ore samples 1 and 2, respectively. Microorganisms were sampled from the bioreactor for the analysis of their community structures by Illumina MiSeq high-throughput sequencing. The analysis show that the suspensions added with different ore samples had different microbial diversities and richness. This study provides new insight into the biosolubilization of rock phosphates by a microbial consortium directly taken from rhizospheric soils.