Search Documents

By R. S. Kinasevich

As part of other work related to the studies of kinetic factors that influence the flotation of specific sulphide minerals, specially designed kinetic flotation experiments at Cominco included work done on -65 + 100 mesh and -100 + 150 mesh, high purity galena. The flotation collector used was sodium isopropyl xanthate containing radioactive sulphur-35. Radiation monitoring of the galena fractions from stage flotation tests indicated that the adsorbed radioactive xanthate was uniformly distributed among the floated fractions and the non-floated, or residual portion of the galena. This anomalous behaviour could not be correlated to changes in Seebeck coefficients, to lattice distortions, or to the nature of the mineral surface as revealed by infrared spectroscopy and by microscopic measurements.

Jan 1, 1970

By Ulrich Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 kilometers north of Atlanta, Georgia. The project consists of: a 28-meter high dam, a 90-centimeter diameter outlet conduit; an emergency spillway; and a 4.0-meter diameter hard rock trans-basin diversion tunnel. This floodwater management system was part of Cities Service Company mine safety program for the Cherokee orebody which is partially located within the stream channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1978

By Felicia F. Peng

Employing the combination of two types of polyelectrolyte might become necessary to enhance both settling rate of the flocs and water clarity of fine particle suspension in high capacity thickening process. The sequence of addition, mixing, type and dosage of polymer affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance including high settling rate of flocs, underflow density and overflow water clarity, by either adjusting pH prior to anionic polyelectrolyte flocculation, or using a combination of polymer flocculant and coagulant (dual polymer system). The dynamic thickening testing results showed that only the approach using a dual polymer system is able to meet the required performance. The effects of polyelectrolyte dosage, the sequence and numbers of polyelectrolyte addition, feed concentration, bed level and rake speed on the settling rate, underflow solid, and water clarity were studied in cylinder test and a laboratory dynamic thickening unit with various conditions related to the thickening process. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively, using total suspended solids in supernatant, underflow density and capacity per unit settling area per unit time as the measure of effectiveness. The objective of this study is to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1997

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The history of Duluth commences with Daniel de Greysolon du Lhut, one of the explorers of the Upper Mississippi who came to the head of the lakes in the summer of 1679. Radisson and Groseillier, and Claude Allouez, a Jesuit priest, are supposed to have visited the head of the lakes, -but there is no authentic record previous to that of du Lhut.In 1792, the fur traders established a fort at Fond du Lac, fifteen miles up the St. Louis River from Lake Superior, but within the limits of the present city •of Duluth. In the early 50's, there were a few scattering settlers at Oneota and around the George Stuntz trading post on Minnesota point. In 1855-6, the settlement on Minnesota point was called Duluth, commemorating the name du Lhut, and organized as a town in 1857. The first board of trustees and town council consisted of -William Nettleton, J. B. Culver; Robert E. Jefferson, Grin W. Rice and William Old: In 1870, the city of Duluth was incorporated, and five years later a portion of the same territory was incorporated as the village of Duluth, and the two municipal corporations were still in existence on March 1, 1887, when the city and the village of Duluth were incorporated as the present city.The first saw mill in Duluth was erected in 1856-57, on the present site of the ship canal. It cut logs from a virgin forest at the upper end of Minnesota point.The first railroad was built to the head of the lakes in 1870. The charter for this road had been granted in 1861 to the Lake Superior and Mississippi Railroad Company, afterward called the St. Paul and Duluth, and which is now a part of the Northern Pacific Railroad."

Jan 1, 1920

By J. Loeb, R. Ramanathan, P. Cameron

All mining operations, including iron ore, maintain a focus of continuous improvement and asset optimisation in their operations. As all the operations in the Mine-to-Mill value chain are inter-dependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and the impact of changes to the process. In this paper, we discuss some of the key attributes in the mine to mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve mine to mill processes. Mining operations are planned and executed based on designs and models to achieve the operation’s objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Measurement of the key attributes establishes the baseline for Mine to Mill (or Pit to Plant) performance which is necessary to understand the impact of any proposed improvements to the process design and execution and to monitor the outcomes on an ongoing basis to sustain the improvements that have been implemented. We have focused this paper on two types of measurement – blast movement and particle size of materials through the mine to mill process. Several innovative technologies are already available to measure these attributes and assist operations improve productivity and mine site profits.

Mar 2, 2022

By R. R. Bhappu

The metallurgical processing industry is in the midst of a hydrometallurgical revolution with mining companies looking for low cost, energy efficient and environmentally friendly technologies for processing sulfide ores and concentrates. The Intec Copper Process is one of the most advanced of these technologies and has the potential to greatly change the way copper concentrates are treated in the future. Specifically, the Intec process has the ability to be built on a small scale and at mine sites while being much more economic than conventional smelting. Intec Copper has constructed a I tonne of copper per day demonstration plant in Sydney, Australia designed to verify metallurgical and operational performance. This paper will describe the process in more detail and provide preliminary results of the process based on the plant's performance. It will also compare the Intec Copper Process with a few of the competing technologies and evaluate the relative economic merits of Intec.

Jan 1, 1999

he leaching behavior of palladium in ammoniacal solutions has been investigated by using the rotating disk technique in an autoclave. The study included the effect of rotating speed, temperature, oxygen pressure, composition of ammoniacal solutions, and catalyst on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in view of the thermodynamics and a kinetic model. Even though the potential-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was too slow at temperatures below 100°C but was significantly improved at higher temperatures. It was also found that the rotating speed of palladium disk had no effect on the leaching rate. The apparent activation energy was found to be 69.7 kJ/mole. Based on the results obtained, it is concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1997

By Ed Schodowski

Wireless technology is a hot topic for anyone involved in the design, operation, maintenance or upgrading of mines or mineral processing plants because wireless technologies overcome barriers that have prevented many useful data inputs. Wireless communications can contribute to worker safety, satisfy environmental concerns, support plant security, track human and physical assets, and improve equipment maintenance. The cost structure of wireless is compelling and users can realize savings ? up to 90 percent less installed cost than wired instruments ? since wireless technology eliminates the need for expenses associated with cabling, engineering, construction and documentation. Many applications previously considered too expensive have become economically feasible with wireless. Two examples are continuous monitoring of safety showers to notify operators when one has been activated, and monitoring effluents to ensure environmental regulations are being met. In many cases, wireless transmitters can be installed where wired devices were too expensive to justify, or were not feasible due to physical or technical barriers. Examples include monitoring temperature measurements inside a rotating reactor or monitoring process variables in a tough, corrosive environment too challenging for a wired solution. Wireless also gives operating personnel mobility with the ability to communicate from remote or hard-to-reach zones. According to a recent Venture Development Corp. survey covering radio frequency (RF) of microwave industrial monitoring and control products, these features are contributing to the expected nationwide growth rate for industrial wireless applications of 19 percent annually from 2007 to 2012 (Taylor, 2008). At the same time, mineral producers have many questions about wireless systems including their applicability, reliability and security in this industry. Just what can wireless do? Is it secure and reliable? Can these instruments stand up to the rigors of the industry? Can wire-less technology provide the flexibility needed for mining applications?

Jan 1, 2009

By Kadri Dagdelen, Lee J. Zamalloa

Modern surface mining operations are always seeking for minimizing costs while increasing production rates, among the optimization of other specific tasks that have an impact on the economics of the mine. Specifically, the cost related to the production fleet operation (shovels and trucks), the maximization of the overall performance of the equipment, and the uncertainty to meet the goals at the end of the operational time horizon are always topics of discussion with no apparent simple answer. On the other hand, truck-shovel dispatch systems based on Linear/Non-Linear Programming Algorithms have been in operation since mid-1990’s with different levels of success depending on the correct arrangement of operational resources and the complexity of the mine, but having in most cases some important shortcomings related to the way these systems deal with the decision making of the operational objectives, being necessary to have a human agent (dispatcher) to guide the system when the operational parameters change, creating the possibility of suboptimal decisions due to the human factor. This paper discusses the implementation of a novel methodology based on AI techniques to assist in the decision making of the best goal selection when operating a Fleet Management System, taking into consideration time periods as variables and integrating them as part of the analysis, providing a better overview of the forecast plan completion with respect to previous production numbers and evaluating best alternative to handle future events to minimize losses or maximize profits, resulting in better truck assignments, minimum shovel idle times and overall productivity improvements of the operation at the end of the time horizon.

Jun 25, 2023

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents with particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and the conditioning time were investigated to determine their effect on reagent coating on the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power P, to the minimum power Pm' required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain high recovery. Reagentization was slower at lower P /P m ratios. At higher P /P m ratios, the flotation recovery was optimized and the agitation speed was found to have no significant effect on it. Optimum mixing conditions were obtained for a 74 wt% slurry at an agitation speed of 450 (47 rad/s) rpm. Under the optimum conditions of mixing, recovery was improved at low collector dosages and short conditioning times.

Jan 1, 1995

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By Alton G. Woody

Like so many installations of its type approaching middle age, the ore processing and shipping facilities in Puerto Ordaz, Venezuela, have taken a lot of twists and turns in their lifetime. The object of this paper is to lead you through these twists and turns and some of the reasoning for them. The need for additional sources of iron are in the United States became evident during the time of the second world war. An exploration team from U. S. Steel located further high quality direct shipping iron are in commercial quantities near Ciudad Bolivar, Venezuela in 1947. Basic decisions were made to develop these reserves for export via the Orinoco River through a new shipping port to be built at the confluence of the Orinoco and Caroni Rivers. The basic concept was for the ore to be loaded directly to ocean going vessels. This was something of a gamble since the basic economics depended upon successfully opening up the main channel of the Orinoco River to deepwater vessels, and the Bethlehem Steel mine in the same area was already working with shallow draft river boats and a transfer station on the coast. Always, the basic philosophy has tended to be to plan with expansion in mind. The original conveyor systems were 1.52 m (60 inches) wide with 200 idlers, whereas 1.07 m (42 inches) or 1.22 m (48 inches) wide conveyors could have carried any production foreseen at the time of installation. Stockpiles have been located and designed with room for expansion. Basic designs have had dotted line future expansion blocked in.

Jan 1, 1978

By W. C. Taylor

The present fuel situation indicates that, at least for the next 20 to 30 years, the burning of coal will be a main source of energy. All coal contains sulfur, which is converted to sulfur dioxide during combustion. The concentration of sulfur dioxide (SO2) in the resulting flue gas, for most coals, would exceed the limits established by the Environmental Protection Agency (EPA). Therefore, the sulfur must either be removed from the coal prior to its burning, or be collected from the stack gas before it reaches the atmosphere. There is currently a large amount of research devoted to methods of removing the sulfur from the coal before burning, or during combustion in fluidized beds with materials which trap the sulfur in the solid residue. The commercialization of these processes, however, is not expected in the near future. Flue gas desulfurization appears to be the best near term prospect of fulfilling current air quality control regulations. The lime/limestone wet-scrubbing methods are the most advanced flue gas desulfurization processes and will account for the majority of sulfur removal systems in electric power generation. There are currently at least 23 full-scale systems existing or under construction and 17 of these will use the lime or limestone wet-scrubbing process. (1)

Jan 1, 1974

By Michael J. Beus

This paper describes research conducted under the BuMines's Advancing Metal and Nonmetal Mining Technology Program, a major element being the application of new and improved technology to shaft design in deep underground vein-type mines. Two basic design parameters considered in shaft planning are configuration (shape) and ground support. The most common shapes are circular and rectangular. Ground support systems include concrete, timber sets, steel sets, rock bolts, and steel liners. The inherent advantages and/or disadvantages of various shaft designs such as ventilation and fire resistance, flexibility and ground support characteristics are well known. Circular concrete-lined shafts have minimal resistance to air flora and are virtually fireproof, an important consideration in deep hot mines. However, concrete does not yield significantly, and failure conditions and misalignment cannot be easily repaired. Timber-supported rectangular shafts predominate in the Coons d'Alene Mining District with its highly stressed and frequently heavy ground. The sets can be relieved and reblocked when out of alignment. However, the constant maintenance and repair requirements result in exposure to an inherently dangerous working environment combined with excessive operating costs. Obviously a dilemma exists--a circular, concrete-lined opening has many desirable features, provided it is strong enough to withstand the stresses involved. Rectangular, timber supported shafts have proven adequate in the Coeur d'Alenes; however, the implication of increased maintenance and repair requirements on ever-deepening shafts in this district and other similar areas will be an important design consideration in the future. This paper, then, presents shaft-configuration and ground-support guidelines to help remove some of the uncertainty concerning the stresses to be encountered in typical deep vein mining areas.

Jan 1, 1976

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

By Walter R. Lawrence

Newmont Gold Company, formerly Carlin Gold Mining Company, is a publicly owned corporation, 95% owned by Newmont Mining Corporation. Newmont Gold Company has operated gold recovery operations North of Carlin, Nevada, since 1965. Development of the Gold Quarry ore body, 19 kilometers south of the original mine, resulted in the decision to construct gold recovery and ancillary facilities in what is referred to as the Southern Area. Plant No. 2, located 11 kilometers North of Carlin, Nevada, was designed to treat 6350 tonnes per day of oxidized gold bearing ore assaying 2.5 grams per tonne of Au at an average recovery of 87%. Flowsheet development conducted by Newmont personnel resulted in the decision to construct a carbon-in-pulp recovery circuit preceded by two-stage grinding, Detailed engineering was done at Toronto by Bechtel of Canada beginning on January 1, 1984. Actual construction began on March 1, 1984, and was completed in June, 1985. First feed was run on June 22, 1985.

Jan 1, 1987

By F. Habashi

The Republic of South Africa is a heterogeneous mixture of Black Africans, Afrikaans, British, Indians, Malayans, French Huguenots, and many others from Europe and Asia. A decisive date in its recent history is the collapse of the Apartheid Regime in 1994. For a metallurgist, South Africa is the country of diamonds, gold, platinum, and many other metals. In 1887 Cecil Rhodes (1853-1902) was able to take control of the De Beers Mining Company after the discovery of diamonds at Kimberly in 1866. It was there where the so-called School of Mines was inaugurated in 1896.

Jan 1, 2010

By E. Gutierrez, P. Gillies

Asset Maintenance Readiness (AMR) provides a tailored reliability and maintenance strategy specific to operational needs. AMR delivers reliability and maintenance foundations for the plant and equipment before start-up. Having a dependable reliability and maintenance strategy before start-up is critical, particularly in those first weeks and months during ramp up to stable production. The Asset Maintenance Readiness is the integration of Reliability and Maintenance Engineering analysis/studies at the earliest stages of the new Production System concept and design and during the Capital Project CapEx phases; adding this analysis to the Capital Project CAPEX cost, will have an impact of 2% to 3% of total project cost, but will deliver a good compendium of benefits far from the AMR costs, and those results will be shown upon commissioning and during the life cycle of the plant.

Mar 2, 2022

By D. L. Moellenberg

Under various state laws enacted mostly within the last 20 years, reclamation requirements and standards for hard-rock mining operations have been established virtually everywhere in the western United States. Unlike the uniform and detailed coal mine reclamation requirements under the federal Surface Mining Control and Reclamation Act ( "SMCRA" ) and state programs mode led after SMCRA, the various state law hard-rock mine reclamation requirements are based upon a variety of objectives, and therefore are subject to varying standards from state to state. While the diversity of reclamation requirements complicates the determination of what reclamation measures will be required at any particular mine, there are valid reasons for this diversity. There are dozens of different commodities mined in the United States, and mining methods are different for each commodity. Local natural conditions such as climate, precipitation, geology, hydrology, and biology vary widely across the county. Site-specific conditions also affect mining and reclamation methods. Also, factors such as economics, land use, and environmental protection issues receive different priorities in different states and communities within those states. State reclamation requirements in general provide the flexibility to consider site-specific circumstances, allowing operators to design and engineer the best reclamation measures for each mining site. To the mine developer or manager, reclamation requirements must be translated into design, operational, and closure measures for mine planning. Each of these measures must then be assigned additional costs to be factored into the economic decisions for a particular mining operation. On a broader level, reclamation costs must be factored into decisions such as where to invest in exploration and mine development. The purpose of this paper is to provide a summary of the state non-coal mine reclamation requirements in twelve western states. This summary comparison may be useful as a starting point in considering how local reclamation requirements will impact potential mining costs.

Jan 1, 1994

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570° and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 2, 1984