Search Documents

By James R. Aggson

This paper summarizes the research effort that was conducted as part of a cooperative agreement between the U.S. Bureau of Mines, Denver Mining Research Center and the Pittston Company. The objective of this investigation was to further the understanding of the floor heave ground control problems that have plagued underground mining of the Beckley coalbed in southern West Virginia. Floor heave is both economically and structurally undesirable. Floor heave is accompanied by a redistribution of stresses and loads that are associated with an underground opening. This redistribution of stresses may cause roof or pillar problems that otherwise would not have occurred. The floor heave that occurs in the Beckley coalbed is not cons1dered to be caused by "squeezing" or plastic flow of the materials involved. The "squeezing" type floor heave is normally associated with relatively weak floor members that contain significant amounts of clay mineralization. The floor members in the Beckley coalbed are competent, relatively strong materials which fail in a manner that can best be described by the term "buckling." This buckling-type failure is indirectly related to the time-dependent deformation properties of the materials involved, but is considered to be more of a slender column, or panel, type failure than a "squeeze" or "flow"-related failure. The Beckley coalbed has had a history of floor heave ground control problems. The Glen Rogers mine, which opened in the 1920's, experienced extensive floor heave. In a report dated April 1929, James P. Keatley of the West Virginia State Department of Mines described the floor heave in the Glen Rogers mine. Several observations listed in the Glen Rogers report that appear to be consistent with current observations follow: 1. Water plays no apparent part in the floor heave process. 2. No evidence of gas has been found in the floor. 3. The thickness of the overburden, which varies from 183 to 396 m (600 to 1300 ft), has no relationship to the floor heave. In the conclusions of the 1929 report on the Glen Rogers mine, Keatley states, "A statement in brief as to the cause (of floor heave) would lie that an undetermined natural condition doubtless augmented by former and present mining methods causes the bottom to heave." As this report will show, Mr. Keatley's insight into the problem was most accurate. The "undetermined natural condition" is the existence of a biaxial, horizontal, compressive stress field. This stress field is in excess of that which would be expected from gravity loading. This stress field and the material properties of the floor rock combine to cause the floor heave that has been experienced. The floor heave that occurs in the Beckley seam generally occurs as arching, with a tension fracture, near the center of the floor span or as a break near the rib followed by vertical deflection (of the floor) at the rib and sloping of the floor across the entry. Examples of the floor heave are shown in Figures 1 and 2. The two types of floor heave are merely different manifestations of the same basic failure mechanism. When the entries experiencing floor heave were identified on a map of the mine under investigation, it was apparent that there was a relationship between the floor heave and the direction of the entries. The main entries, which are used for ventilation and haulage, experienced the majority of the floor heave. This directional relationship suggested a directionally related loading mechanism, or more specifically, a biaxial, horizontal stress field that exceeds what would be expected by gravity loading. Since the main entries were oriented at a bearing of N25oW, it was hypothesized that the maximum compressive component of the horizontal stress field was at 90° to these entries or at a bearing of N65oE. An in Situ testing program was developed to test this hypothesis and investigate the floor heave problem.

Jan 1, 1978

By B. S. Hulvey

Thin support liners are becoming more accepted and being developed with improved properties because the mining industry as a whole has been offering underground safe test trial sites. This is because of the huge potential for such products. Recent developments tend to indicate that the technology is “coming of age” and these are discussed in this paper.

Jan 1, 2003

By D. R. Spears

The U.S. Bureau of Mines has had an ongoing interest in developing new reagent schemes for floating Stillwater, MT, chromite ore. Previous reagent schemes have been unsuccessful in achieving complete separation, primarily because little is known about the surface chemistry of the minerals in this ore. In order to design a rational reagent scheme, a study of the binding of various functional groups (R = -H, -OH, -CO2H, -NH2) on the two components (chromite and forsterite) of the Stillwater chromite was undertaken. Electron Paramagnetic Resonance (EPR) Spectroscopy was used to determine the adsorption isotherm, from a cyclohexane solution, of spin-probes which contained the functional group of interest. This was complemented by studies of the saturation surface coverage of the spin probe on the two minerals. In each case, more sites existed on chromite than forsterite; however, the forsterite sites were more strongly binding for each functional group. The results are discussed in terms of their implications for flotation.

Jan 1, 1994

By Yuexin Han, Yanjun Li, Peng Gao, Yongsheng Sun, Qiang Zhang

The non-isothermal magnetization roasting process and isothermal magnetization roasting process of siderite ore were investigated using thermogravimetric (TG) analysis and a real-time infrared gas analyzer. X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) were used to analyze the characteristics of samples. The results showed that the decomposition degree and decomposition rate of siderite ore were vitally affected by heating rate and roasting temperature. It was determined that A1 reaction model (f(α) = 1 − α) and A3/2 reaction model (f(α) = (3/2)(1 − α)[−ln(1 − α)]1/2) were the most probable mechanism function of the non-isothermal decomposition process and isothermal decomposition process, respectively. The phase transformation and decomposition mechanism during the roasting process were evaluated. Siderite decomposed in the process of magnetization roasting, released CO and CO2, and transformed into strongly magnetic magnetite. The SEM images highlighted that as the decomposition progressed, the structure of roasted samples was destroyed, and an increasing number of cracks and pores emerged on the surface, which is advantageous to the following grinding process.

Mar 26, 2021

By J. R. Heberger, B. H. Ngo

The Safety Pays in Mining v2.0 web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app categorizes injury cost by part of body injured, by the cause of the injury, or by the nature of the injury. When the user selects one of over 150 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining v2.0 will estimate the total costs of the selected injuries and the estimated impact of total injury costs on mining company profits and will provide some examples of services and personal protective equipment on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining version 2.0 web application by discussing the development and updates to the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app.

Feb 1, 2024

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

By S. M. Bulatovic

The western industrial world has to rely more and more on complex polymetallic sulphide ores as sources for base metals. These ores are composed of fine grained sulphide minerals such as chalcopyrite, galena, sphalerite, pyrite, pyrrhotite and marcasite. The liberation sizes of the individual minerals can range between 30 um and 5 um. Therefore, applying conventional techniques to recover these finely disseminated minerals usually results in unsatisfactory metallurgical performances with high losses of the valuable mineral to the slime , fraction of the tailing. New concepts for treating these polymetallic complex ores are discussed in this paper. Beneficiation techniques utilizing new reagents and a new approach to pulp preparation are described. Some of these techniques were applied to ores from existing concentrators as well as to new ores. The results of these studies are discussed in the following sections.

Jan 1, 1990

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018

By D. Randall Crooke, Ron R. Jorgenson

Many coal combustion products (CCPs) have historically been unsuitable for placement as mine backfill because of their physical and geochemical properties and/or regulatory status. However, innovations in paste production and transport of CCPs utilizing the high, fine particle contents of these fine-grained waste materials and their water retention colloidal properties produce a non-segregating, self-cementing material that may be environmentally suitable for placement as mine backfill. Both industry and the regulatory agencies are enthused by the possible cost reductions, both in design and construction of disposal sites, and the reduced environmental impacts of CCP realized by implementation of this new use/disposal technology.

Jan 1, 2001

By Lennart Bergstedt

Boliden Aktiebolag, the prime base metal mining company of Sweden, annually treats some 11-12 million tons of sulphide ore in nine concentrators. Its first flotation plant was established in the early thirties for the complex Boliden ore. Since then, the number of mines and plants has gradually increased. Considerable effort has been devoted to the development of all phases of the technology of ore prospecting, mining, milling, smelting and refining. This has been necessary due to the complex and low-grade ores. The development of concentration has mainly been directed toward the arts of grinding and flotation. During the forties and fifties, open-stage fine crushing followed by two-stage grinding in rod and ball mills with cyclone classification was successfully introduced and used throughout the plants. The increasing cost of grinding media led to studies of an autogenous grinding technique as early as 1945. Basic test work commenced during the early fifties, with a. number of ores tested for pebble grinding. In 1956 a new pilot plant was built, with equipment installed for the continuous testing of pebble grinding and, later, for primary autogenous grinding of run-of-mine ore. The intensive test work showed that pebble grinding was feasible in almost all of the plants. At this early stage of testing, however, the merits of autogenous grinding could not be fully evaluated. As a. consequence the rod mill/ball mill grinding systems were converted to rod mill/pebble mill systems whereever possible. In parallel with the converting of grinding systems the development work concerning the merits of autogenous grinding went on. The major result

Jan 1, 1977

By Ramiro da Conceição do Nascimento, Horst Guenter Feldhagen, Rafael Piumatti de Oliveira

Mixed hydroxide precipitate (MHP) is a nickel intermediate product that has economical benefits to downstream leaching of lateritic marginal ores. Usually, this product is subsequently processed and refined to produce nickel by hydrometallurgy, but an alternative route can be made integrating hydrometallurgy and pyrometallurgy. Assessing the overall consumption of ferroalloys to obtain stainless steel, as an increasing practice performed in China, the synergy of nickel extraction from laterites by leaching and precipitation asMHP with the production ofMHP agglomerates applied as rawmaterial to furnaces of ferronickel production is a very attractive practice. This work aims to further the technological development of an agglomerated product feasible to hydro-pyro integration. The agglomeration experiments were performed by traditional pelletizing (firing the pellets) and cold bonded pelletizing (aging the pellets by appropriate stocking). Appropriate compositionswere prepared withMHP, additives and binders for each of these routes. A specific study of binder composition was made to find an adequate melting point. The produced pellets were tested to prove their properties by crushing strength tests. The standardization applied to iron ore was followed. The best result of crushing strength was 98.52 daN/pellet. The agglomerates with approved crushing strength for use in electric furnaces were smelted to produce alloys containing nickel; the agglomerates were characterized by scanning electron microscopy. The alloy obtained was metallic ferronickel with sulphide precipitates. Therefore, MHP pellets can be precursors of nickel alloys, which have to be refined to obtain the desirable composition.

Jul 6, 2020

By Rainer Antretter

"THE CHALLENGE The 14km long, Arlbergtunnel, closed for public traffic during summer 2015, receiving a comprehensive and substantial renovation from 2015 to 2017. The main works discussed here, carried out during 2015, comprise 37 drill and blast SEM/NATM emergency escape tunnels from road level to the ventilation duct plenum have to be constructed as well as eight additional lay-by niches and three transformer tunnels. This presentation comprises the construction ventilation design, designed according to national regulations, suitable for 150 employees working 24/7 simultaneously at more than 40 single working sites lined up along the tunnel. The ventilation-system chosen was utilising two existing shafts for intake/discharge and a cross passage to surface, to handle a total fan power of 1.600kW. DESCRIPTION OF RENOVATION WORKS Linking Tyrol and Vorarlberg, two Federal States of Austria, the Arlbergtunnel is a single tube two-way road tunnel with vent duct plenum, constructed in the mid-1970s. According to latest EU legislation, additional escape exits have become obligatory. The existing seven cross passage links to the adjacent Arlberg Railway Tunnel, with average spacing of about 1.500m constructed in 2007, an additional upgrade to shorter escape spaces of approx. 400m was now required to comply with the updated legislation. Additional transformer tunnels, lay-by niches and small niches for emergency maintenance use, cleaning and other purposes, as well as a the installation of a new fire main in the invert, coupled with the simultaneous replacement of virtually the entire power and signaling cables, generated several dozen small and large single sites distributed along the 14km of tunnel.Purpose of the 37 walkable emergency escape tunnels is to reach the “upper deck” of the Arlbergtunnel, the vent duct plenum. These have an 180deg curve in plan, inclined at 10% and approx. 60m (65yd) long tunnels, excavated using drill and blast method starting from road level and working upwards to the level of an “intermediate soffit”, the vent duct plenum in the crown of the tunnel. The vent duct plenum is separated into a fresh air part and an exhaust air part, shown in Figure 1. The escape tunnels end with a pressure door in the fresh air section of the ventilation duct plenum. From there illuminated signs show the shortest escape route to the safe area between the road tunnel and the railway tunnel, as shown in Figure 2."

Jan 1, 2016

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke, and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale Fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL) in Fairchance, PA, using Ponderosa Pine, Red Oak, Douglas-fir, high and low volatile coals, PVC and SBR conveyor belt, No. 2 diesel fuel, and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector, and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations, and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (1). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters? Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2012

By İsmail İnce

The purpose of this study is to investigate the index-mechanical properties of igneous rocks by using the electrical resistivity method. Electrical resistivity, index (P-wave velocity, dry density, and porosity), and uniaxial compressive strength values of 48 different igneous rock samples were measured in the laboratory. Simple regression analysis was performed between index-mechanical properties and electrical resistivity values. Strong exponential and logarithmic correlations were found between electrical resistivity and the index-mechanical properties of the igneous rock samples.

Jan 21, 2022

By N. Del Bel Belluz

Drilling underground in the Grasberg De-watering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are utilized; pilot-holes to probe ahead of the tunnel development to intersect aquifers ahead of the face; and de-watering holes to de-water rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, rates of 1050 psi static pressure have been recorded with flows from a NQ hole measured at 1350 gpm (US). The water flows can be slightly acidic, necessitating the use of stainless steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early to deal with these conditions. The collar gear is used to control water flows whereby the water is treated as an important resource. As a result, pm has established procedures to maintain safety of the drill crews, enable coring of the rock and to maintain safety of the miners who are driving the drifts.

Jan 1, 1998

By L. B. Phelps

Current mining regulations require revegetation in reclaiming surface nines. Excessive soil compaction can be an impediment to successful revegetation in poor soil conditions common to Eastern coal nine sites. A field study was performed to determine the bulk densities of soils that had been spread by either bulldozers or scrapers at a strip nine site. Moisture-density relationships for the soils were determined from the field samples. These were compared with stockpile samples compacted by the Standard Proctor compaction test. The results of the study indicate that the degree of compaction could be lessened through proper soil handling procedures.

Jan 1, 1986

By Robin Dill, Wei Song, Andrew Perham, Leo Martin

"AECOM completed a subsurface exploration program for an 18-foot diameter, approximately 4-mile long rock tunnel project in Hartford, CT. The tunnel crosses the regional geologic trend through the middle of a sedimentary basin, passing through four separate rock formations, including two volcanic flows. Faulting is prevalent, with at least 15 faults encountered during the site investigation. Severe artesian flows were also experienced in several of the borings, requiring highly specialized drilling equipment. Sixty-two borings and associated testing were performed to characterize the structural geology, hydrogeology, rock properties and ground conditions. A phased program was carefully planned and implemented with participation of geotechnical and geologic specialists, with thoughtful evaluation along the way to react to the ground conditions encountered, and make appropriate refinements. This paper will discuss the subsurface program details; the integrated efforts used to effectively characterize the ground; and will summarize the final characterization presented in the GBR. PROJECT DESCRIPTION The South Tunnel Conveyance and Storage Tunnel project is part of the Metropolitan District (MDC’s) Long Term Control Plan to address discharges to various water bodies throughout the greater Hartford area. This program includes a main conveyance and storage tunnel; a tunnel boring machine (TBM) launch shaft and retrieval shaft; adit tunnels with associated drop shafts and connection structures; consolidation conduits and manholes; and a tunnel pump station (TPS) at the downstream end of the main conveyance tunnel. AECOM is serving as prime designer for the MDC on this project. The main conveyance tunnel (hereinafter referred to as the “South Tunnel”) will be a deep rock tunnel with an invert depth of approximately 180 feet at its downstream end and approximately 218 feet at the TBM retrieval shaft. The tunnel will have a finished diameter of 18 feet. The tunnel will rise in grade at a slope of 0.1 percent to its upstream end. Total invert depth along the deep tunnel alignment ranges from about 180 ft. to as high as 320 feet. The total length of the tunnel will be 21,754 feet. The South Tunnel will be constructed using a shielded TBM and fully lined with pre-cast concrete segments."

Jan 1, 2016