Search Documents

By G. Bryant, P. Ziemkiewicz

Acid mine drainage (AMD) from both abandoned surface and underground mines is a serious problem. The flow of water and changes in quality over time from abandoned mines is important in determining remediation strategies. Acid mine drainage from surface mines is estimated to last for 10-20 years, while estimates of acid drainage from underground mines vary from 10- 100s of years. Fifteen underground mine discharges in West Virginia were studied to compare water quality changes between 1968 and 1999 to see if our data are consistent with other studies. Each of the discharges were categorized into one of three groups: undisturbed since 1968, affected by surface mining since 1968, and reclaimed. Comparing water quality between 1968 and 1999, the discharges in the undisturbed category showed a 35 to 95% improvement in acid concentration and a 40 to 99% reduction in iron concentration. The discharges affected by surface mining showed the most dramatic improvement. For acidity, iron, and aluminum, the percent improvements were all above 44%, and in most cases in the 70 to 99% range. In the reclaimed category, one of the four discharges declined in water quality. Discharge 82 showed a 76% increase in acidity, and iron and aluminum concentrations worsened by 58 and 96%. However, discharges 15 and 74 improved in water quality with a 94% acid load improvement and a 95% iron load improvement at both sites.

Jan 1, 2000

By Richard J. Robbins

Mechanical raise and tunnel boring are new techniques to most of the mining industry. Coal, salt and potash have been bored economically, but until recently boring machines were not designed specifically for rock boring in underground mining. The construction industry has led the field of rock boring since 1854 when the first tunnel boring machines built by James S. Robbins and Associates went to work at Oahe Dam, South Dakota. Since that time the company has built boring machines for tunneling through ground conditions varying from cohesionless soil to hard rock, and in diameters ranging from 7 feet to 36 feet 8 inches. It is natural that the construction industry got the jump on mining with the use of mechanical rock boring equipment. Mines have looked for the long range answer to problems of underground excavation and they have chosen proved and established techniques they expect to employ for the next ten or twenty years. The mine development was laid out to accommodate these techniques.

Jan 1, 1964

By James E. Lawver

During 1981 the Florida phosphate industry produced more than 43 million metric tons of phosphate rock - about one-third of the entire world production and also generated nearly an equal amount of waste clay and waste clay-sized product that requires dewatering and disposal. The material balance of solids and water for a typical Florida phosphate mining operation is shown in Figure 1. Historically, the industry has impounded clay waste (about 60% below ground and 40% above ground) in earthen dams, often as large as 800 acres and occasionally greater than 60 ft. high. The dams have served the triple purpose of: 1. Dewatering initial 3% solid waste clay for process water re-use. 2. A reservoir system to minimize water discharge from the mining area and to capture and store rainwater thus minimizing deep well pumping requirements. 3. The ultimate densification and storage of waste clay.

Jan 1, 1983

By L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million ton'> of ash, boiler slag and FGD (flue gas desulfurization -"scrubber") materials as by-products. Utilities and others who burn coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Jan 1, 1997

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021

By A. J. Plumpton

Centrifugal air classification and li-quid-phase sedimentation are the principal methods of industrially sizing materials of dimensions smaller than those handled by screens. Increasing application of materials such as composites and high performance ceramics has furthered the need for closely-sized, fine, industrial mineral and synthetic products of controlled properties. Sedimentation can be used to separate very small sized particles but introduces problems of liquid-solid separation, de-agglomeration and drying. Some of the advantages and limitations of centrifugal air classification will be discussed and laboratory and plant measurements using centrifugal machines will be presented to support the discussion.

Jan 1, 1990

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

By Harry H. Peek

Artesian pressures of unusual magnitude occur in the deeper aquifer units beneath a considerable part of southeastern North Carolina and extend into South Carolina. The high pressures were first observed in 1968 in wells near Wilmington that were drilled to "basement" rock and which were screened between depths of about 260 to 300 m (meters). The pressure was recognized by Peek and Heath1 as an anomalous geo-pressure and unrelated to recharge conditions in the region. Since 1973, much new information has been obtained on hydro-geologic conditions in the area and a preliminary report on the deep artesian pressures was published in 1975.2 Most of the basic information has been obtained from groundwater research stations constructed by the Groundwater Section of the North Carolina Department of Natural and Economic Resources as a part of Ground-water studies in the Coastal Plain Region. These stations consist of an exploratory well drilled to basement rock with wells completed in each principal aquifer unit to provide data on aquifer characterestics, water levels and water quality.

Jan 1, 1977

By M. S. Safarzadeh, V. Agarwal

"The solvent extraction of cerium(III) and samarium(III) from mixed solutions of all rare earth elements (REEs) except promethium using PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), an acidic extractant, was investigated. The effects of aqueous equilibrium pH, various acids (sulfuric acid (H2 SO4 ), hydrochloric acid (HCl) and nitric acid (HNO3 )), initial metal ion concentration and extractant concentration on the solvent extraction of Ce(III) and Sm(III) were systematically studied. From the experimental results, HNO3 and HCl were found to be the preferred aqueous media for the solvent extraction of both Sm(III) and Ce(III). The most promising experimental conditions of pH, PC88A concentration and metal ion concentration were identified for the extraction of Ce(III) and Sm(III). Separation results showed that H2 SO4 at pH 2 provided the best separation between Sm(III) and Ce(III). IntroductionIn recent years, demand for rare earth elements (REEs) has increased significantly because of their many commercial applications. REEs have especially important high-tech applications owing to their unique physical and chemical properties, and they are used in a wide range of areas such as catalysts, ceramics, magnets, lasers, glass, neutron absorption and alloys. As REEs have very similar physicochemical properties, their separation and purification from each other is challenging and gaining significant interest. Samarium (Sm) and cerium (Ce) are found in different REE minerals, including bastnäsite ((Ce,La,Nd(CO3)F), xenotime (YPO4) and monazite ((Ce,La,Nd,Th)PO4) at major production sites in the United States and China, as listed in Table 1 (Bleiwas and Gambogi, 2013). The most common acidic organophosphorous extractants used for REEs extraction and separation are DEHPA (di-(2-ethylhexyl)phosphoric acid), PC88A (2-ethyl hexyl phosphonic acid mono-2-ethyl hexyl ester), Cyanex 272 (bis-2,4,4-trimethylpentyl phosphinic acid) and Cyanex 301 (bis(2,4,4-trimethylpentyl)dithiophosphinic acid) (Sarangi, Reddy and Das, 1999; Surampally et al., 2012; Tian, Jia and Liao, 2013). Out of these extractants, PC88A is known for providing higher separation factors (Acharya, Mishra and Misra, 2015). El-Hefny et al. (2010) investigated the kinetics of the solvent extraction of Sm from chloride media using sodium salt of Cyanex 272 and reported the extracted species to be Sm(OH)A2•2HA. Lee et al. (2005) investigated the solvent extraction of Sm(III) with PC88A and saponified PC88A from chloride solutions and found the stoichiometry of the extraction reactions to be 1.5 with PC88A and 3 with saponified PC88A."

Jan 1, 2017

By Robert B. Tippin

A number of recent studies 1-4 suggest that steelmaking expansion might be achieved more economically by a combination of the prereduction furnace and the electric steelmaking furnace rather than through new blast furnace construction. Supergrade concentrates would be the first step in an evolving technology which bypasses the blast furnace and in which the concentrates are first made into pre¬reduced pellets and then used directly in electric steelmaking, Prereduced pellets made from superconcentrates should not only be competitive with scrap, but should be a preferred feed for the electric furnace because of the absence of such residual elements as copper and nickel. Furthermore, geographic areas remote from present steelmaking centers may find the electric furnace to be an economical method of providing local steel requirements. The development of successful methods of producing superconcentrates may also be expected to find application to conventional blast furnace burdens. The need for methods of increasing grade of domestic concentrates will become increasingly urgent in the face of competition from high grade imports. Only a small percentage of domestic iron ore production can qualify as superconcentrates, (Superconcentrates for the purpose of this investigation are limi¬ted to those concentrates which contain a maximum of 2 percent S'02). During the last several years the Twin Cities Metallurgy Research Center of the Bureau of Mines has directed research efforts to develop methods of manufacturing superconcentrates from present standard grade products by cationic flotation, screening, and magnetic separation.

Jan 1, 1971

By Eckl, Martin, Stefan Lemke, Martin Londschien

"Tunnels are built with a design life expectancy of over 100 years. One key component of such a design is the waterproofing system, which must reliably fulfil its function during the whole service lifetime of the tunnel structure. This paper deals with the determination of test criteria for the durability assessment of geosynthetic products in tunnel sealing systems. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa. To verify the results of the new test procedure the material properties of geosynthetic products samples removed from older tunnels are investigated. Based on the presented results of the still ongoing research programs some preliminary conclusion regarding the updating of regulations for tunnel sealing systems are given. INTRODUCTION Watertightness is directly related to the durability and serviceability of the concrete lining. Therefore, modern traffic tunnels and shafts (Figure 1) are generally protected against mountain/ground water and water penetrating through rock fissures by a sealing system, for example with a loose-laid polymeric sheet membrane. Hereby the waterproofing sealing systems must be reliably fulfilling their function during the whole service life of the tunnel structure, regularly of more than 100 years. In consequence, the quality and lifetime performance of the waterproofing materials—beside the correct professional and careful installation in a tunnel infrastructure, is of great importance. The challenge for the industry, owners, operators and designers is ultimately the development of qualification testing and requirements (acceptance criteria) for products to ensure the design lifetime performance. Hereby the qualification procedure is seen as a routine integrated in standards, norms or guidelines, wherein test procedures should cover typical environments for the specific application fields. Polymeric synthetic raw materials are increasingly used in products with long service lifetimes (e.g. in injections, gaskets, waterbars, spray-applied and sheet waterproofing membranes). During service they are subjected to chemical (e.g. oxidation processes) and physical (e.g. changes in morphology) influences from the environment, which affect their mechanical properties—and they age. Hereby organic materials are more affected than inorganic materials. Also, polymers show strongly temperature-dependent properties compared with other construction materials. However, their long-term aging behavior is not given per se and has to be explored extensively by suitable tests, which simulate—under accelerated processes—real exposures and loads. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa."

Jan 1, 2016

By M. Misra

Improved liberation and flotation of kerogen from eastern oil shale were accomplished with high-temperature grinding and a1 so with the addition of fuel oil during the grinding stage. Liberation measurements indicated that possible coalescence and aggregation phenomenon of kerogen particles during grinding may reflect this behavior. Additionally, ultrasonic treatment of the rougher concentrate prior to cleaning improved the quality of separation.

Jan 1, 1984

By Wm. Terry Siemer

Abstract. The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded 227 million. 1e state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fluorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand Non metallic resources are distributed throw out the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9 percent to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1980

By A. W. Khair

This paper deals with the evaluation of the interaction between rock and the cutting tool, and with methods for determination of workability, and abrasivity of rock. A description of instrumentation is included along with research on the wearing process of bit tips and pick consumption. Analyses of bit rotation, evaluation of cutting, normal forces and energy consumption is presented. Finally influence of the basic water jet parameters and water jet assistance on the cutting process of hard and abrasive sandstone is discussed.

Jan 1, 1995

By Qingming Feng, Jinhong Zhang

A study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature, and curing time significantly affect the mechanical property of geopolymermatrix. Through optimization, an above-100MPa compressive strength has been achieved with the geopolymerization products. The optimum working conditions involves 10MNaOH concentration, 14–15% water content, and curing at 90 °C in an oven for 1 day or at ambient condition for 3 weeks. Adding Ca(OH)2 does not help to increase the compressive strength of the specimen.Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength, even after a 1-month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS (scanning electron microscopy and energy-dispersive X-ray spectroscopy), XRD (X-ray diffraction) and ATR-FTIR (attenuated total reflectance Fourier transform infrared) are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method for applying fly ash as a high-strength water-resistant precast construction material.

Aug 17, 2020

By Y. Guan

The adsorption of zinc species onto silica in ammonical solutions has been studied. Adsorption isotherms reveal that increasing adsorption occurs as the solution pH is made more alkaline. Fr-IR spectroscopy revealed that the adsorbed species is a zinc ammine complex.

Jan 1, 1993

By T. Dunn

FMC Corporation has achieved a significant cost reduction through a new proprietary solution mining and processing technology at its Green River, Wyoming Soda Ash Facility. In the first phase, completed in October 1995, trona ore is dissolved, recovered and processed with the new technology, and then fed into an existing refining plant, replacing dry mined and calcined trona ore. The second phase, completed in April 1996, produced a fmal high purity product and increased capacity by 635,000 t/a (700,000 tpy). Both phases were completed under budget and well ahead of schedule.

Jan 1, 1998

By Raul A. Deju

This paper shows how one can relate the chemical reactions between water and a silicate bed to the equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented.

Jan 1, 1969

By L. Yuan, J. H. Rowland, R. A. Thomas, D. Bahrami

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time. INTRODUCTION Underground miners are at risk of overexposure to toxic gases from various sources. Production blasting operations using explosives in underground mines are a source of multiple toxic gases that could be harmful and even fatal to humans if prolonged exposure occurs beyond the safe limits. According to Code of Federal Regulations, Title 30, Part 57.5002 [1], metal and nonmetal mine operators must conduct gas, mist, and fume measurements as frequently as necessary to determine the adequacy of control measures to protect miners from overexposure to harmful gases. MSHA will inspect mine operators’ activities to verify the evidence of such measurements [2,3]. Continuous gas monitoring in the return air is an effective way to make sure that toxic gas concentrations at the working areas are kept below the regulatory limits before the return of miners. Toxic gases can enter the mine atmosphere from different operations, such as welding, combustion, and blasting. The main gases produced from blasting are carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), and nitrogen dioxide (NO2). Other gases are produced in small amounts and, therefore, were not considered for this study. Related regulatory and recommended exposure limits of CO, NO, and NO2 gases are summarized in Table 1 [4].

Jan 1, 2019

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016