Search Documents

By Michael L. Cramer, Kunsoo Kim

INTRODUCTION The Columbia River Basalt beneath the Hanford Site is one of several rock types being considered by the U.S. Department of Energy for the first commercial high-level nuclear waste repository. The Basalt Waste Isolation Project (BWIP) has been carrying out a comprehensive investigation to assess the feasibility of constructing a repository in basalt and to develop technology required for repository engineering and site characterization. Development of a nuclear waste repository requires a number of design considerations not usually necessary in the planning of conventional underground structures. Principal among these is the thermally induced stress field resulting from waste emplacement. This thermal stress, super- imposed on the preexisting in situ- and excavation- induced stress fields, needs to be evaluated in the design process due to the sensitivity of waste emplacement density to this factor. The nature of this thermally induced stress field is dependent on several factors, including the temperature distribution around the repository openings, the thermal properties of the rock mass, and the deformability of the rock mass. Re1iable performance of the repository structure is largely determined by the ability to under- stand the above rock mass characteristics and predict the underground opening response to waste emplacement based on this understanding. To gain an understanding of this rock mass behavior in a repository condition, the BWIP has conducted a large-scale heated block test in basalt at the Near-Surf ace Test Facility (NSTF) on the Hanford Site. This paper presents the results from the elevated temperature phase of the block test in which the thermal, mechanical, and thermo- mechanical response of the closely jointed basalt rock mass was evaluated as a function of stress and loading orientation at varying temperatures up to 200 oC. SITE GEOLOGY The NSTF test areas, including the block test site, are located in the entablature zone of the Pomona basalt f low. The Pomona flow entablature is structurally typical of most flows in the Columbia River Basalt Group in that it is characterized by long, undulating, polygonal columns up to 2.4 m in length. Columns vary from 15 to 30 cm in diameter, averaging about 20 cm. Over their length, columns can vary in dip by 150 to 200. The column structures are dissected by subhorizontal cross joints that are generally discontinuous and seldom cross columnar joint boundaries. Spacing of the cross joints also averages about 20 cm. A representative joint pattern taken from mapping of the tunnel wall near the block test site is shown in figure 1. Application of the Rock Mass Rating System (Bieniawski, l979) to the block test site yielded an overall value of 62. The corresponding value from application of the Q-system (Barton et al., 1974) is 8.7 (Cramer and Kim,1985). The NSTF is approximately 50 m below the surf ace. However, this depth is sti1l above the water table and conditions are generally dry. Interstitial water exists as the result of percolation of meteoric water from the surface.

Jan 1, 1986

Innovative mining technology came to Texas in the form of bucket wheel excavator/cross-pit spreader systems. Texas Utilities Mining Company put the first system to work at its Big Brown Mine in December 1985. The second such system was put into operation at the Monticello Mine in February 1991. The cross-pit spreader systems are mobile, electrically powered, excavation and conveyor systems, the principal components of which include bucket wheel excavators (BVE) and an across-the-pit conveyor (spreader). These crawler mounted machines operate as a unit; the BVE's excavate overburden, feed it via conveyors to the spreader which in turn conveys the material across the open pit and onto the developing spoil bank. The system at the Big Brown Mine is composed of 2 BVE's and an across-the-pit conveyor while the Monticello system is made up of 1 BVE and a spreader. The BVE's prestrip overburden preparing a dragline bench for the final removal of overburden. Numerous evaluations, including lignite production requirements, economics, overburden characteristics, rehandle reduction, spoil stability, and the compatibility with dragline operations, led to the selection of the cross-pit spreader system at the Big Brown Mine. The system has proven itself as a viable and economical means of prestripping. The system's success at the Big Brown Mine led to the development of a second such system at Monticello. The advent of the cross-pit spreader system is viewed by Texas Utilities Mining Company as a viable solution to recovering deeper lignite reserves in a safe and economical manner.

Jan 1, 1993

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996

By Steven A. Bradbury

INTRODUCTION Passive dust control systems are quickly gaining acceptance in the bulk solids handling industries. The number of applications is increasing due to proven performance, especially in US power plants burning Powder River Basin coal. Air Control Sciences ®, Inc., of Boulder, Colorado, has over forty (40) patented Dustless Transfer ® systems in operation. All of the installations control workspace dust levels to less than 2.0 mg/m3, and in some applications reduced conveyor dusting by over ninety-eight percent (98%). Passive systems control fugitive dust emissions by minimizing the induced airflow in bulk material transfer and slowing its velocity. Traditionally, fugitive dust control in the mining industry was accomplished using either dust collection systems or dust suppression systems. The term passive dust control, indicates these methods don't use any active dust collection or suppression. Passive dust control systems are best suited to transfer from one conveyor to another. They can also be applied to transfers from feeder to conveyors.

Jan 1, 2004

By R. Mishra

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solutions. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors will demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning.

Jan 1, 1977

By Bern Klein, Richard W. Lawrence, Scott Frostad

A laboratory study was conducted to evaluate the effects of various kinetic test protocols on sulfate production, NP depletion and time to acidity. Six test protocols were evaluated including standard humidity cells, non-aerated cells, tall cells, shaken cells, simulated precipitation cells, and NP depletion columns. The study indicates that test protocols which disrupt the oxidizing environment, such as extreme wetting and drying cycles, shaking the cells, or the high addition of acidic water will create an unnatural environment that affect the results. Trickle leach and non-aerated test protocols create an oxidizing environment that more closely represents field conditions and are therefore recommended.

Jan 1, 2000

By L. Adler

The valuable Maximum Utilization Factor (MUF) concept has been extended to other rotating excavators beyond stripping shovels and draglines. In this concept the boom reach and bucket capacity are multiplied to get an MUF, then normalized by dividing by the equipment weight. Statistical analyses were applied to the remaining shovels (hydraulic and cable), draglines, and backhoes. Positive correlations were found. Stripping shovels and draglines were also re-examined. The results provide an estimate of equipment diggability and encourage versatility by the interchange of the boom and the bucket. The concept further clarifies the existing equipment classification by delineating general excavating, loading, and stripping kinds. The results also forecast trends, and noted innovative advances and possible retrogression. Extension to other boom excavators, such as front-end loaders is recommended. The MUF concept provides one of the few indices of gross external characteristics available to the engineer-user of equipment.

Jan 1, 1990

By William R. Hess

Volcanic ash, although a little-used Kansas resource, is available in forty counties with estimated, reserves of more than 20 million tons. It was first produced in Kansas in the early 1900?s but not until the early 1920 is did it become an important abrasive material. Total production to date is estimated at 2 million tons, the major use being as an abrasive in scouring compounds and soaps, additional uses include ceramic glazes, an additive in cement, and a filler and stabilizer in hot mix asphalt for paving. Unrecorded tonnages have also been used in construction of black-top (macadam) roads. From 1916 through 1944, Kansas ranked first among the states in volcanic ash production; peak production was about 52, 000 tons in 1923. Since 1945, production has steadily declined, primarily because materials other than volcanic ash are now being used for abrasives; only two producers operated in 1964.

Jan 1, 1965

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By Carl E. Williams

During the past two years a computer program called "COPOR," Computerized Open Pit Optimization Routine, has been developed and used for mine planning of several base metal deposits. This routine utilizes a three dimensional computerized block model of an orebody, some economic parameters and operating constraints to locate the mineable or economic limits of the deposit schedule the yearly production from the mine and produce bench by bench ore reserve summaries and maps of the yearly and ultimate pit configurations. The moving cone method is used to perform these functions with a conventional block model. This model is conventional in the sense that each block is assumed to be homogenous; i.e., either ore or waste but not a mixture of the two. Due to the nature of a seam type deposit this approach is not realistic; therefore, revisions have been made to form a new version of the COPOR program. This version has been named "COALOR," Coal Optimization Routine. COALOR contains all of the power of the COPOR program but is equipped to handle the intricacies of coal seam type deposits. The deposit can be composed of a single seam or multiple seams which are horizontal or dipping at any angle. The numerous coal quality values can be incorporated to aid the optimization of the economic pit limits and yearly scheduling.

Jan 1, 1978

In the grand scheme of things, the 9.5-t (21,000-lb) shipment of molybdenum concentrate that left Freeport-McMoRan?s Climax Mine site on May 10, 2012 was not unlike the thousands of others that have been hauled away from the site during the last century, except for the fact that this shipment marked the official rebirth of one of America?s greatest mines. For nearly two decades, 17 years to be exact, there was no production from the mine that was once the largest underground mine in the world and was so important to the Allies? effort during World War II that it was assigned the highest priority of any mine in the United States by the War Production Board. The economic recession in 1980 put an end to the mine?s success, and the Great Recession of 2008 nearly derailed the mine again. But, like the nearby town of Leadville, CO, the mine survived thanks to an investment of more than $700 million by Climax Molybdenum Co., a Freeport-McMoRan company, to bring the Climax Mine back into production.

Jan 1, 2012

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By Gabriel K. Nzulu, Lars Hultman, Per Eklund, Martin Magnuson, Abu Yaya, Prosper M. Nude, Hans Högberg

This study aims to identify individual elements and to gain an understanding of the surface reaction mechanisms, as well as the properties of precipitated pyrite particles observed during the hydrothermal formation of an ore deposit. A combination of X-ray diffraction (XRD), air annealing in a furnace, scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX), and X-ray photoelectron spectroscopy (XPS) was applied to investigate the crystal structure and identify the individual elements, permanence, transformation and chemical/electronic properties of such pyrite.

Jun 1, 2024

By L. F. Zeiler

In the past, health concerns in coal mines have primarily centered on those elements which have been essentially inherent to the mining environment. These would include respirable coal mine dust, respirable crystalline silica, excessive noise levels, and diesel exhaust particulates. Commercially-available chemical products are prevalent on mine property. These potentially toxic materials are chemical formulations that can degrease, clean, and lubricate metal parts, separate coal from rock in float/sink operations, and aid in roof consolidation, among other uses. As the general public has become more aware of the hazards of chemical exposures, miners have likewise become more concerned about working with an ever-expanding variety of chemical products on the job. Often, product or chemical specific hazard communication training is inadequate or ineffective, and miners do not know exactly what the ingredients are in the products they handle, or the health hazards involved with their use or misuse. Currently, the Mine Safety and Health Administration (MSHA), by law, enforces 1972 Threshold Limit Values (TLV). MSHA is making preparations to adopt new personal exposure limits for enforcement. The values given throughout the article are 1994 TLV's and are not enforcement standards, but are used for discussion purposes. They reflect the current scientific thinking regarding personal exposure to these chemical agents. An overview of these products is presented, and the potential health hazards associated with their use are discussed. Controls needed to prevent overexposures, such as proper handling procedures and personal protective equipment, are covered. Methods used to collect and identify contaminants are presented.

Jan 1, 1995

By Y. Q. Lu

Efficient flotation of fine phosphate minerals from a deslimed waste phosphate stream (-74 microns) has been achieved by both bench-scale flotation and by flotation with a 2-inch air-sparged hydrocyclone (ASH) unit. A sample was collected from the waste phosphate slime stream at the SF Phosphate Limited Operations near Vernal, Utah, for flotation experiments at University of Utah laboratories. The collector used was a mixture of fatty acid, petroleum sulfonate and kerosene. Bench-scale flotation test results show that the minus 15-micron particles have a significant adverse effect on phosphate flotation. When the minus 15-micron material was removed by a classifying hydrocyclone, improved flotation recovery and concentrate grade were realized. A bench-scale flotation recovery of 86 % with a concentrate grade of 16% P2O5 was obtained from classified waste slime (74 x 15 microns) feed material containing 11.3% P2O5 In contrast, a 90% P2O5 recovery was achieved with a concentrate grade of 16-18% P2O5 by single-stage ASH flotation. With a second stage of ASH flotation, a concentrate containing 23% P2O5 was realized at an overall recovery of 75%. These results indicate that the industrial application of ASH flotation technology for phosphate recovery from waste slimes is promising.

Jan 1, 1995

By J. B. Knaebel

I have been asked to discuss the "Development of the Twin Buttes Mine for Production." This property, which is a large low-grade open pit copper mine about 25 miles south of Tucson, Arizona, was recently brought into production by The Anaconda Company under a long-term lease agreement with the Banner Mining Company. Since the scope of this paper is limited to the subject broadly indicated by its title I will confine discussion of historical, environmental and other general matters to a brief summary sufficient, I hope, to establish a background of those conditions which influenced our approach to the technical and economic problems that faced us at Twin Buttes. The paper deals primarily with our studies and activities related to the solution of these problems and with the resulting engineering and business decisions that were taken - decisions which culminated last September in the initial commercial operation of another major open pit copper producer unique and interesting in several respects.

Jan 1, 1970

By Richard W. Hornung, Steven Samuels

A great amount of work in recent years has been devoted to refining older survivorship models, e.g. life tables, and developing newer ones, e.g. Cox regression. In this paper, these models are applied to data from an epidemiological study of uranium miners in four western states conducted by the U.S. Public Health Service. One of the principal problems addressed in this paper concerns the appropriateness of using cumulative dose as the measure of radiation exposure. An alternative is considered that incorporates dose rate into the model. This procedure does not implicity assume that equal cumulative doses produce the same lung cancer mortality, but instead considers the amount of time in which each miner's dose was accumulated. Results of the statistical analysis indicate that dose rate is a significant factor at higher cumulative dose levels, with lower dose rate apparently more damaging than higher dose rate. The shape of the dose response curve is curvilinear at higher dose levels. No interaction was found between smoking and radiation exposure on a multiplicative or relative scale.

Jan 1, 1981

By Roshan B. Bhappu

Stimulated by current $0.80 to $1.20 per pound price tag of copper, considerable interest and activity have been generated in the copper mining camps throughout the world, and especially in the Southwestern United States and Northern Mexico copper belt. Under these economically favorable conditions, many of the marginal oxide-copper deposits, as well as newly discovered prospects, are under scrutiny for possible exploitation. For both the known deposits and new prospects, the big question facing the mine operator is the selection of the best method for processing these economically attractive oxide-copper deposits. Several variations of the hydrometallurgical processes are currently available for treating oxide-copper ores which can be mined by the open-pit method. Basically, these processes involve preparing the ore for application of an acid solution, applying the solution to the ore, and recovery of the metal from the pregnant solution. Dump leaching, heap leaching, vat leaching, agitation leaching and, in more recent times, in situ leaching or solution mining in combination with well established cementation process or the newly developed solvent extraction-electrowinning system have all been employed or have been investigated for the recovery of copper from oxide ores. Of these processes, dump, heap and vat leaching have been successfully practiced for treating oxide-copper ores. Agitation leaching is a relatively newcomer and has been adopted from the experiences of uranium and gold processing. Finally, the inplace leaching technique is the latest process to be suggested for possible treatment of oxide-copper ores.

Jan 1, 1974

By Charles Dumaresq

The management of mine tailings poses a complex range of potential risks, including physical risks, such as the risk of catastrophic failure of a tailings facility and chemical risks such as the risk of long-term leaching of contaminants into the downstream environment. If these risks materialize, they can lead to a wide range of impacts on people and the environment, including human fatalities and severe impacts on downstream ecosystems, and the costs of recovery borne by industry, communities, governments, and society as a whole can be immense. Tailings facility failures in Canada (2014), Brazil (2015 and 2019), South Africa (2022), and in other locations around the world underscore how high the stakes are when mines produce and manage tailings (WISE Uranium Project 2019). Understandably, many people do not trust the mining industry to manage tailings responsibly. As an industry, it is our responsibility to manage tailings in a manner that is responsible and strives to minimize harm associated with tailings management, including effectively managing both the physical and chemical risks associated with tailings. Standards have an important role to play in responsible tailings management by setting expectations for standards of care and providing a means to measure and report on performance. In jurisdictions with strong legal requirements for tailings management, standards play a complementary role, pushing performance improvements in areas that may be difficult or impossible to address in legal requirements. In jurisdictions where legal requirements are lagging, standards may represent the de facto leading practice and may be the primary tool to help ensure responsible tailings management. Implementation of standards can help companies demonstrate that tailings are being responsibly managed and help build trust and credibility. Most importantly though, standards are important tools to help ensure that the risks associated with tailings are reduced, and that remaining risks are effectively managed. However, we must recognize that conformance with standards can have a down-side – the proverbial two-edged sword. Having standards is vital but there is a risk that implementing standards becomes a “box checking” exercise, with ongoing conformance leading to complacency. We must not allow ourselves to fall into the trap of believing that, just because we are complying with applicable standards and laws, we are therefore doing our best, and that “it can’t happen to us.” In addition, if conformance becomes the goal and the standard does not have mechanisms to drive continual improvement, then once the standard is met, there may be no incentive to improve. The point of complying with standards is not to pass the test. The point is to manage tailings responsibly, prevent catastrophic failures, and minimize harm. The point is to do better, because we must do better. To do that, we need to strive not for conformance, but for excellence in tailings management, driven by continual improvement and a quest to do better.

Feb 1, 2025

By Kelly Sands

"Mitigation may be considered a hurdle when it comes to environmental permitting. For complex projects with site specific mitigation plans, the time to devise those plans and get them approved can be a long and costly endeavor. However, mitigation options are expanding and the mitigation banking industry has grown tremendously over the last two decades, helping projects move forward with less debate. Mining companies are recognizing the value that mitigation banks provide in helping to shore up project timelines and costs. Where possible, companies are taking advantage of the opportunities to buy credits from thirdparty providers offering mitigation bank credits. In some instances, mining companies are taking matters into their own hands by establishing mitigation banks to realize their own mitigation freedom. That can have its advantages and disadvantages, as discussed below. All in all, the expansion of mitigation options has streamlined the permitting process, introduced flexibility, improved project permitting timelines and loosened the permitting girdle.Compensatory mitigationCompensatory mitigation involves actions taken to offset unavoidable adverse impacts to wetlands, streams and other aquatic resources and authorized by Clean Water Act section 404 permits and other permits. As such, compensatory mitigation is a critical tool in helping the federal government meet the longstanding national goal of ‘‘no net loss’’ of Waters of the U.S., both in acreage and function.Section 314 of the National Defense Authorization Act for Fiscal Year 2004 required the Secretary of the Army, acting through the Chief of Engineers, to issue regulations “establishing performance standards and criteria for the use, consistent with Section 404 of the Clean Water Act, of on-site, offsite, and in-lieu fee mitigation and mitigation banking.” The provision also required that those regulations ‘‘maximize available credits and opportunities for mitigation, provide flexibility for regional variations in wetland conditions, functions and values, and apply equivalent standards and criteria to each type of compensatory mitigation’’ (73 FR 19595). The result was the Final Rule on Compensatory Mitigation for Losses of Aquatic Resources issued in 2008 (33 CFR Parts 325 and 332).”"

Jan 6, 2017