Search Documents

By Eugene A. Hickok

Seismic surveys utilizing the MD-1 have been performed by Geophysical Specialties Company since 1957 in many parts of the, U. S. and Canada and in several foreign countries. These surveys have proven the refraction seismic technique to be applicable to a wide variety of engineering problems. The best known applications of the instrument have been in the, construction industry, where it is used for the delineation of material and mineral deposits and for bedrock depth determinations. Fast on-the-site depth determinations give reliable subsurface' information even in boulder-strewn soils. A widely publicized use of the MD-1 is to make rippability studies in which the instrument is used to determine the seismic velocity of the materials to be excavated. By use of special tables which correlate rippability with seismic velocities, such as those prepared by the Caterpillar Tractor Company using the MD-1, the rippability of-a specific material may be determined.

Jan 1, 1962

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By Barbery G., A. Maachar, M. Bourassa

Laboratory testing for flotation circuit design is carried out on a routine basis in a large number of lab- oratories throughout the world. Usually a sample of ore, assumed to be characteristic of the material to be processed in a future plant, having a mass of the order of a few kilograms, is ground in a batch ball or rod mill, in the presence of water and some re- agents (for pH control, etc. .. ); after dilution to the adequate solid concentration, the resulting slurry is transferred into a laboratory batch flotation machine, having a volume which can vary from 0.5 to 8 10 -3m3. Various types of machines are in common use, manufactured by the same companies that market industrial size flotation machines. The operation of flotation in the laboratory is carried out by an experienced technician, who uses parameters such as impeller rotation speed, air flowrate addition, froth height, froth removal rate, in conjonction with reagent addition sequence, to "test" the ore. After flotation, the froth products ("concentrates"), and the solids remaining in the cell are filtered, dried, and analyzed for the various elements of interest. For flotation circuit design, a kinetic test is usually carried out, in which the froth products obtained at various times are collected to assess the time response of the ore in the laboratory machine with the combination of reagents used. Although this description is rather sketchy, it enables to outline some of the major difficulties in using laboratory data for flotation circuit design: 1. ore sample representatively 2. feed preparation procedure (laboratory compared to industrial scale) 3. laboratory procedures (type of ma- chine, type of operation, experimental errors. . . ) 4. flotation machine scale-up 5. flotation kinetic scale-up 6. flotation circuit design using laboratory data These various points will be discussed in the present paper, in order to stress the problem areas as well as possible solutions. ORE SAMPLE REPRESENTATIVITY It has been stated many times that one of the major problem in designing a flotation circuit is the representatively of the sample to be taken. Sampling of an ore body during prospection and evaluation is a specialized field, which has been progress in with the introduction of geostatistics. The application

Jan 1, 1986

By N. W. Johnson

The behavior of non-sulphide gangue in chaloopyrite flotation circuits has been investigated. Plant and laboratory tests were carried out on five different ores, and linear relationships were found to exist between the rates of recovery of water and free nonsulphide gangue in the concentrates although there was evidence from pilot plant tests that these were linear approximations to parabolic curves over the limited regions which were observed. There was evidence that the free non-sulphide gangue enters the concentrate by hydraulic classification and a classification function has been proposed to define this behavior. This function is suitable for inclusion in a mathematical model of the process.

Jan 1, 1972

By James Humphrey

There is a natural resistance to change in any form. When it comes to implementing a game-changing technology like autonomous haulage on an operating mine site, the resistance can at times appear insurmountable. Whether based on real information or misguided preconceptions, it?s essential that we don?t underestimate the effort it will take to overcome this resistance, while clearly recognizing when it?s worth the effort. These realizations did not happen overnight for sites where autonomous haulage has been implemented. Nor did they happen overnight for manufacturers of autonomous mining equipment. Caterpillar, for example, began building toward autonomy more than 30 years ago and had a truck operating in the mid-1990s. Lessons learned during those early years led to the realization that there was much more to be learned ? not just about the machines themselves, but about the systems and knowledge that must be in place for a successful implementation. Working closely with customers, initiating real-life demonstrations on mine sites, having discussions with regulatory agencies and other stakeholders ? these and many other activities were necessary before autonomy could be fully and successfully launched. After decades of effort, Caterpillar?s first official commercial autonomous mine site went to work in 2011 in Farmington, NM.

By A. E. Isaacson

Bureau of Mines researchers developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1987

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling payloads in excess of 290t. Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Since truck haulage costs can account for 10%-50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, vehicle operating and maintenance costs would also increase prohibitively. There is thus a need for improved design technologies encompassing the construction and management techniques of mine haul roads, appropriate for the wheel loads of vehicles now in use. The aim of the paper is to present the different components of a mine haul road design and management system and to demonstrate the value of its application through case studies. The system has been applied at several South-African surface mines and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and also provided better service, whilst the optimal selection and management of wearing-course materials provided better functionality at lower total transportation operating costs.

Jan 1, 1999

By P. G. Dempsey, J. R. Heberger, J. P. Pollard

During a mine disaster or emergency, underground air can quickly become contaminated. In these circumstances, all underground mine workers are taught to don breathable air supply units at the first sign of an emergency. However, no contemporary oxygen consumption data is available for the purposes of designing breathing air supply equipment specifically for mine escape. Further, it would be useful to quantify the oxygen requirements of breathing air supply users for various escape scenarios. To address this need, 14 participants crawled a distance of 305 m each while their breath-by-breath oxygen consumption measurements were taken. Using these data, linear regression models were developed to determine peak and average oxygen consumption rates as well as total oxygen consumption. These models can be used by manufacturers of breathing air supply equipment to aid in the design of devices that would be capable of producing sufficient on-demand oxygen to allow miners to perform self-escape.

Jan 1, 2015

By Natalie White, Joel Asp, Allyz Kramer

"Minnesota has robust reclamation standards and have proven results in the taconite mining industry. Reclamation of overburden spoils, lean ore spoils and fine tailings from taconite production has generally been successful on the Iron Range, using a low input standard reclamation practice. Success at reestablishing vegetation on these landscapes is likely due to fairly favorable chemical and physical properties (e.g., few limitations due to acidic generating materials, metal toxicities and water and nutrient holding capacities). However, coarse tailings reclamation has proven more difficult, presumably due to lower nutrients and challenges with moisture holding capacities. Research efforts conducted since 1990 have struggled to develop a reclamation strategy for coarse tailings that meets the Minnesota Mineland Reclamation Rules, Chapter 6130. However, new breakthroughs in scram mining technologies are producing fine and coarse tailings that have not been encountered nor reclaimed in northern Minnesota. Scram mining in Minnesota is defined as those mining operations that produce natural iron ore concentrates. Innovative research is underway to investigate and determine successful reclamation strategies to reclaim scram mining tailings from these scram mining operations. The research program is conducted through collaboration with SEH, Prairie Restorations, Inc. (PRI) and Mining Resources, LLC with funding support from the Iron Range Resources and Rehabilitation Laurentian Vision Partnership minescapes grant program.The research program was divided into three phases:Phase I. Bench-scale testing to identify successful treatments to reclaim and restore scram tailings through evaluating surface soils amendments, viable seed mixes and plant germination, growth and densities. Phase I was completed in early 2015.Phase II. Field-scale pilot trial to test larger scale effectiveness of the treatments deemed successful in Phase I and test various vegetative assemblages and planting techniques focused on the unique challenges with scram tailing basins. Phase II was completed in late 2016 with a summary monitoring report.Phase III. Produce a technical report of results for the research undertaken in this study, as well as compile prior reclamation results used during previous Minnesota iron mining reclamation projects on tailings basin applications. Phase III was completed in 2017 with a summary monitoring report and recommendations."

Jan 2, 2018

By R. C. Bunge

A magnetogravimetric separation is the consequence of two competing forces with opposing directions, i.e., magnetic buoyancy and gravitation (or centrifugal force). While magnetic buoyancy is a function of particle volume, gravitational force depends on particle mass, thus permitting a separation according to specific gravity. Since magnetic buoyancy is not a phenomenon of common knowledge, this chapter is meant to briefly introduce the theory of magnetogravimetric separations. A particle that is suspended in a magnetic fluid which is exposed to an inhomogeneous magnetic field experiences a repulsive force -the so called magnetic buoyancy. In order to illustrate this effect, an analogy with the more familiar hydrostatic buoyancy is drawn. Hydrostatic buoyancy occurs due to unsymmetrical pressure distribution 'above' and 'below' a suspended particle (fig. 1).

Jan 1, 1990

Gaby Copper Mining?s Gabriela Mistral property is located in the Antofagasta region of northern Chile, at an altitude of 2,660 m (8,727 ft) above sea level. The reserve contains an estimated 562 Mt (620 million st) of oxide ore with an average grade of 0.41 percent total copper. The mine went into production in 2008. Gaby Copper faced the problem of having no reliable way to measure the solids level. This is a challenge that exists throughout the mining industry, where dust in the air and accumulation of solids on a sensor make accurate measurements difficult in areas such as transfer chutes, the rock box underneath crushers, silos and anywhere else that information is needed on the level of solids. The next-generation technology in the Sitrans LR560 radar from Siemens addresses this challenge. With a frequency of 78 GHz ? higher than previous generations of radar ? it provides a more robust signal for measuring in areas where there are high levels of dust accumulation. The Sitrans LR560 provides a signal beam angle of four degrees, significantly narrower than any other product on the market can offer.

Jan 1, 2014

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Nucleation and growth of copper on 316L stainless steel from synthetic acidified copper sulfate was studied in the absence and presence of chloride ions and/or organic additives (HydroStar® 4208, DXG®-F7, Cyquest® N-900) using a potentiostatic technique. The current-time data obtained at 0.16V vs. SHE was analyzed using nucleation and growth models. Scanning electron microscope (SEM) images of deposits produced at 300 A m-2 show that the addition of 20 mg/L chloride ions increased the size and reduced the number of copper nuclei. Potentiostatic current-time data from the electrolyte without organic additives indicate progressive nucleation with two-dimensional (2-D) growth under diffusion control. SEM images obtained confirmed progressive nucleation with 2-D growth. 20 mg/L Cl- and 2.5 mg/L organic additives did not change the nucleation and growth mechanism, however the additives increased the number and reduced the size of copper nuclei leading to more uniform coverage of the stainless steel substrate.INTRODUCTION Electrowinning of copper is an important process in the manufacture of high purity copper metal. It is approximated that 20% of the world’s refined copper is produced from acidified copper sulfate solutions by electrowinning (Schlesinger, Sole, and Davenport, 2011). In many plants, copper is electrodeposited on AISI 316L stainless steel substrates for a period of 6-7 days, after which the copper is stripped from the blanks. Even though the deposition time for a commercial copper electrowinning circuit is around one week, it is critically important to control the nucleation, growth, and nature of the initial deposit (Sun and O'Keefe, 1992). Deposit morphology and structure are influenced by the real current density at the electrode surface. The real current density across the cathode surface is made uniform by proper design of the electrowinning cell and electrodes and careful operational practice. Even with good design and control, some current maldistribution occurs. The outcome of severe current maldistribution is poor deposits that affect product quality and/or increase energy consumption. To combat current maldistribution and create a larger operating window in terms of current density, temperature, and copper concentration, small amounts of organic smoothing agents (traditionally guar products) are added to copper electrowinning electrolytes. Moreover, these additives inhibit the growth of copper dendrites, which leads to improved deposit quality by producing bright, smooth, and dense cathodes."

Jan 1, 2015

By Angelus S. C. Owili-Eger

The investigation into the hydrologic and hydrogeochemical influence of longwall coal mining in the Appalachian coal basin was under- taken in response to the need to technically address problems of damaged or impaired well yields, and quality deterioration. Prior to this study, issues regarding reduced aquifer yields and degraded water quality had to be handled in a very qualitative manner. Such an approach would, in the long run, claim a heavy toll on the mining industry. The primary objective of this undertaking, therefore, was to provide sufficient and reliable information base for the determination of the local and possibly the regional effects of longwall mining on well yields, and the hydraulic and hydrogeochemical parameters of the immediate surface and subsurface water systems. Specifically, the program was designed to supply definitive data to answer the following series of questions: 1. Does longwall mining affect the quantity and quality of water in local wells above and adjacent to longwall panels and barrier pillars? 2. If the water quality is affected as soon as mining takes place, does it heal? or if it is not affected immediately, does it change over a longer period of time? 3. How do the aquifer water transmitting characteristics respond to induced physical ad hydrologic variations? 4. What is the extent of the various changes in quantity and quality of the water resources? 5. Should and can standard hydrologic evaluation techniques be used to determine the hydraulic properties of highly fractured zones located within a larger and less permeable aquifer?

Jan 1, 1983

By G. B. Amicucci

A Denver Autometrics Particle Size Monitor, PSM-400, was installed at Golden Sunlight Mines, Inc. in October 1988. The PSM-400 measures the grind product's particle size and percent solids. The particle size is used to control grind size by automatically adjusting mill feed rate. The PSM's continuous response to ore changes has improved grind product uniformity and mill throughput. Metallurgical testing has shown the PSM's accuracy to be +/-1 % + 150 µm (100 mesh).

Jan 1, 1991

By Gerd L. Klinkenborg

Throughout the history of the development of mechanical conveyor systems, it has always been an established condition that loads are received at one end of a single-belt conveyor and discharged at the other end, in a point-to-point, manner. In systems designed for the continuous transport of granular materials, vertical or horizontal changes in; direction have always necessitated two or mope single-belt conveyor units, with a corresponding number of motors, assemblies and attendant mechanical and human or electronic controls. Besides these high-cost factors, every change in the system's direction also calls for a transfer point that involves a drop-back of the material from one level to another with some loss of the material and, in many cases, unwanted additional granulation. Where changes in the location of the discharge point are wanted, the conventional single-belt conveyor must either be replaced by a shorter or longer unit or additional units purchased and installed, or existing units rearranged. This can take days or weeks, and involve special expenditures as well as loss of valuable production time.

Jan 1, 1962

By George J. Conroy

Results of a long-term program of electrical parameter measurement in under-ground coal mine working sections, performed by The Pennsylvania State University under U. S. Bureau of Mines sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section's machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt-hours per ton.

Jan 1, 1977

By M. Heger, V. Lund, P. Mongeon, D. Bogunovic, V. Kecojevic

The U.S. coal mining industry consumes a significant amount of energy, primarily diesel fuel and electricity. The continuous global increase in energy demand, high energy prices and environmental issues related to carbon dioxide emission represent a substantial challenge for the mining industry. This paper presents the result of research on development of an integrated data environment system for analysis of energy consumption in a surface coal mine. A case study on an operating surface coal mine is carried out to demonstrate the practical application of the developed system. The research work presented here may be used by mining professionals to help provide the answers to the crucial questions of when, where and how much energy is being used. This developed system represents a framework for efficient management of energy consumption.

Jan 1, 2009

By Philip A. Bucci

The Florida phosphate industry successfully uses froth flotation to concentrate phosphate in: the particle size range of approximately 28 to 150 mesh. However, as recently as 1965, coarse particles in the range of 14 to 28 mesh generally had not been beneficiated by conventional flotation methods at recoveries high enough to be considered adequate. It has been customary to upgrade this coarse material; by "agglomerate flotation" or "skin flotation" using belts, tables or spirals. While these devices have proved commercially effective, their capacities are much lower than those of froth flotation cells. To determine whether coarse phosphate material could be recovered successfully by froth flotation, Armour Agricultural Chemical Company began a series of pilot and plant tests; in April 1965. Objective of the tests was to compare over-all performance of a froth flotation cell design relatively new to the phosphate industry with results from the belt circuit at the Bartow, Fla., plant.

Jan 1, 1966

By Andrea Biagi, Elisa Comis, Gianluca Bella, Enrico De Panicis, Guido Barbieri, Matteo Giani

The Sotra Link Project is a major infrastructure project in Norway involving the design, construction, financing and maintenance of several underground and surface structures between Sotra island and the city of Bergen, among them 23 tunnel portals, 12.5 km of tunnels and a 900 m long suspension bridge. This paper describes the benefits in applying a Building Information Modelling (BIM) approach to tunnelling, from Early Design to the Detail Design Phase. The BIM application to the Sotra Link Project resulted in several improvements, such as efficient handling of clashes and inconsistencies, deeper understanding of effective design choices (reduction of errors), more efficient communication between designers, enhanced control of project quantities and costs. The advantages of the BIM approach during the ongoing Construction Phase are also explained.

Jun 23, 2024