Search Documents

By S. K. Kawatra

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. In order to reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite, and that the bulk of the recovered pyrite is there either as a result of simple entrainment or by being physically locked with floatable coal particles.

Jan 1, 1991

By R. Srikanth

Dust control in high production longwalls is a major problem requiring, among other things, careful attention to the design of operating practices, and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in U.S. longwalls; yet under certain conditions, 31 percent of the shearer operator's dust exposure can be due to support movement. Several methods have been developed for the control of shield-generated dust. Yet the need for better methods is apparent. In this paper, the amount of airborne respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. A total of ten experiments were conducted in five longwall faces in four different mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne respirable dust concentration immediately downwind of the shield moved, varied between 0.12 and 1. 75 mg/m3 in the five longwall faces. The mass of airborne respirable dust generated by shield movement was found to vary between 39 and 386 milligrams per shield move. The results from this study reveal that control of dust from longwall shields requires a combination of approaches involving alternative operating practices, reducing shield dust generation rate, increasing face air flow, and decreasing personnel exposure.

Jan 1, 1994

By Mustafa Akser

Dwindling economic deposits of rutile (TiO2) prompted research on recovering it from secondary sources. One such resource is in Southwestern Turkey feldspar mining rejects that contain 5%-6% TiO2 mostly rutile. Previous studies could only upgrade the TiO2 to 36% TiO2 grade, claiming that the leftover flotation reagents on the surfaces of rutile and host minerals detrimentally affected upgrading of the rutile. As a potential remedy to this concern, a laboratory sample (from an operating feldspar mine in Milas, Turkey) was first caustic scrubbed, then air calcined at 400°C to evaporate the oily reagents. Subsequent physical separation of rutile included wet screening, gravity, magnetic, and electrostatic separation technologies. Such processes indeed improved the grade of the rutile concentrate up to 83 % TiO2 Low recovery of the TiO2 (<20%), was attributed to lack of full liberation of rutile, even at 125x44 micron range; interference with impurity minerals such as sphene and zircon; and simply the process inefficiency in upgrading the fine grains through conventional separation technologies for heavy minerals.

Jan 1, 1999

By L. Zhou, D. Bahrami

Mine ventilation is one of the most important aspects of mining operations in underground mines. It is critical to maintain and deliver required fresh air to the active areas to reduce the risk of overexposure to hazardous contaminants or explosive atmospheres. An unexpected or unknown event such as roof collapse, unexpected mine door closure/opening, a fire/explosion, or fan malfunction could adversely alter the airflow distribution within the mine ventilation network that could lead to a hazardous underground environment. Knowing the occurrence and location of such an incident is of critical importance. In this study, the authors developed a novel methodology to assist mine operators in quickly identifying the location of any abnormal airflow change within the network using the airflow changes at monitored airways. The concept is based on a direct derivative method developed by the authors. This paper provides the details of the developed method as well as numerical verification examples. The application of this method can benefit mine operators and safety personnel in making better decisions during a mine emergency response operation to mitigate hazardous conditions arising from an unexpected airflow disturbance

Mar 2, 2022

By John E. Caffrey

Mr. William. J. Montgomery in his book "Theory and Practice on Mine Ventilation stated "Ventilation is vitally important to underground mining for three reasons: First, it sweeps all workings with a plentiful supply of air and drives to the outside the smoke, gases, and contaminated air which would be injurious to the miners; second, it dilutes and renders harmless the explosive gases emitted from the strata, thus eliminating the dangerous conditions caused by the accumulation of these gases; third, it keeps the mine air as nearly as possible of the same composition as the outside air, thus giving to the miner the healthiest possible condition in which to work...." Specific methods to achieve the above basic reasons for mine ventilation were established in the Federal Coal Mine Health and Safety Act of 1969. Sections 303(y)(1); (y)(2), and Section 317(f)(4) of the Act, which can be broadly described as entrapment features, are controversial and debatable in the minds of many mining engineers in their intent and method for affecting, 303(y)(1) in certain cases prohibits the use of belt haulage entries as an intake for face ventilation, This is to say that air traveling in a belt entry will be placed into the returns and not used for face ventilation, 303(y)(2) limits the velocity of the air on trolley haulage entries. The regulations, as published in the Federal Register, have set this limit at 250 feet per minute unless a higher velocity is approved by the District Manager.

Jan 1, 1972

By William H. Langer

I spent 41 years as a geologist with the US Geological Survey (USGS) conducting geologic studies and preparing peer reviewed maps and reports describing the results of those studies. Since retiring from the USGS in 2011, I have been a consultant specializing in aggregates and other industrial minerals. Consequently, I have had the opportunity and pleasure to apply the information contained in those kinds of geologic maps and reports to real-life situations. About half of my consulting is performing due diligence for mineral resource evaluations of one type or another where resource information has been provided by the property owner. Many of those jobs necessitate that I conduct desktop studies followed by field work. I then use my information to review and comment on the written reports of others; reports variably referred to as geologic reports, resource studies, reserve analyses, and so forth. While there are many well written reports addressing geologic resource issues, I was surprised to see that there are also a significant number of so-called geologic reports that only pay cursory attention to geology. Unfortunately, that lack of rigorous geologic investigation commonly leads to erroneous conclusions. This paper addresses three such reports covering concrete sand, metallurgical gravel, and proppants (frac sand). Although all three examples are located in the Gulf Coastal Plain Province, I do not reveal the exact location of any of the properties for purposes of confidentiality. Furthermore, I have generalized the site descriptions and illustrations. However, all the descriptions faithfully define the geologic situation.

Feb 1, 2024

By A. W. Khair

This paper presents a strength formula for the design of coal pillars. The formula is derived from results of laboratory experiments, studying the effects of primary factors influencing the strength of the coal specimens/pillars. Five primary factors, significantly affecting the strength characteristics of the coal specimens/pillars were identified and extensive laboratory investigations were carried out. The five primary factors were namely 1) coefficient of friction between loading platens and coal specimens, 2) elastic properties of the loading platens, 3) coal specimen geometry, 4) coal specimen size, and 5) rate of loading. Four to nine levels of variation for each primary factor on the strength of coal were studied. An empirical formula, implementing the variation of the primary factors affecting the strength of coal specimens/pillars, has been developed. A comparative analysis of the results provided by this and some well known formulae is also presented.

Jan 1, 1994

By G. A. Shirey

Breakthroughs in software technology and in computer hardware capabilities have opened new opportunities to develop more accurate process simulators and to reduce the operating time to reasonable levels. As a result, there are several new simulation packages being commercialized for modeling coal preparation plants and pulverized coal-fired power plants, and the users of these packages are reporting significant improvements in process efficiency and operating costs by implementing the simulators&apos; results. This paper provides an overview of some of the models currently in use at CQ Inc., including the ASPEN PLUS"" Coal Cleaning Simulator, the Ultramax® process optimization software package, and EPRI&apos;s Coal Quality Impact Model?. Case histories of specific applications are also presented.

Jan 1, 1995

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle&apos;s Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By James N. Orlich

Meridian Gold Company&apos;s Royal Mt. King mine (RMK), a subsidiary of FMC Gold Company, is located approximately 40 miles east of Stockton, California on the western edge of the historic mother lode belt. Gold ore at RMK is associated with a series of northwest trending fault zones hosted in either meta-volcanic or meta-sedimentary rock types commonly referred to as greenstone sulfide and carbonaceous phyllite. Mineralogy studies show gold in both ore types to occur primarily as electrum in the form of 1 -20 um inclusions in pyrite with varying amounts of free milling gold. In carbonaceous ores, gold was not found to be closely associated with carbon. At the start of the current mining operation, three major ore resources were identified. North Pit and Gold Knoll pits were the major greenstone reserves while Skyrocket Pit contained over 60% of the total reserves as carbonaceous ore. Since North Pit and Gold Knoll were to be the first areas mined, the mill began operation in February 1989 with a flowsheet designed for greenstone ores with a carbonaceous expansion anticipated after depletion of the greenstone reserves.

Jan 1, 1992

By W. Norman Sims

A number of forces are at work that are now having an influence on coal handling systems. Changes are occurring and will be occurring at an increasing rate during the next few years. 1. Environmental concerns will dictate that dust pollution and spontaneous combustion and its resulting problems be rigidly controlled. 2. Slurry pipelines will be a reality despite the opposition of the railroads because they are economical and make good business sense. Artifical roadblocks can only survive for a limited time. 3. Coal is now and will remain the most economic fuel, particularly for power generation. This is true in most of the developed nations not just the United States. Increase in demand requires a close inspection of transportation systems. 4. A projected major increase in the export of U.S. coals may never occur without major port developments not the least of which will be the ability to accommodate large ships without demurrage time now affecting such shipments at U.S. Ports.

Jan 1, 1982

By S. J. Zagula

Improved desulfurization of Illinois coals is a widely Shared research goal. The development of a physical cleaning strategy and the results of a project to demonstrate technical and economic feasibility of producing a low sulfur compliance coal from the Illinois Basin are reported. Processing flowsheets to extend or retrofit existing preparation plants are considered. Comminution, conventional and micro-bubble flotation, and selective agglomeration technologies were investigated to maximize pyrite rejection while maintaining high product yield. Batch bench scale testing was followed by continuous pilot plant studies. Parameters included grind size, flow rates, pulp density, aeration, agitation, and reagent dose. An economic evaluation of targeted processes is included.

Jan 1, 1987

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

Preliminary design is underway for a new Southern Nevada Water Authority (SNWA) project that will ensure one of America’s most reliable water systems by providing continued, reliable water service to existing and future customers. The Horizon Lateral is a $1.6 billion water transmission pipeline that includes 7–10 miles of 108-inch finished diameter rock and soft-ground tunnels. The tunnels will traverse volcanic rock in or around the McCullough Mountain Range and the surrounding alluvial basin. The tunneling community will find relevance in hearing about this critical infrastructure project from a leading wholesale water utility owner with a proven track record for on-time, collaborative projects.

Dec 1, 2022

By John A. L. Campbell

Surface dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or imporve a surface dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and flocculation. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established (1). These data will be presented at a latter date.

Jan 1, 1969

By A. E. Halim, J. F. Brune

Debate continues over whether barricading in refuge chambers is a good strategy to survive entrapment emergencies in underground coal mines, in particular fires and explosions. Unlike U.S. coal mines, Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes the merits and problems of using refuge chambers or self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. We found that using refuge chambers may not be the best strategy during extensive fires or when multiple explosions occur. In these situations, mine rescuers are unlikely to be able to extract miners who are sheltered in chambers and, conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as the level 1 emergency exercises required in Queensland, Australia. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Thomas R. Kuesel, Harvey W. Parker

INTRODUCTION This paper describes the use of a shield and compressed air for construction of a short section of a pair of twin single-track tunnels for the Metropolitan Atlanta Rapid Transit Authority (MARTA) transit system. Although only two blocks long, this section posed the greatest difficulties to both engineers and contractors, and is the most expensive section of line construction on the MARTA system. All this derives directly from its setting--these tunnels had to be constructed through mixed-face conditions. SETTING The Broad Street tunnels form a link between the Peachtree Center and Five Points Stations, in the heart of Atlanta&apos;s central business district (Figure 1). Peachtree Center sits atop a solid rock ridge, which inspired the design of a deep rock-mined station, as described in the 1979 RETC. Five Points Station is MARTA&apos;s hub--the intersection of the system&apos;s two main branches. It is located in the old railroad gulch, a filled-in erosional valley at the base of Peachtree Ridge, and was constructed by open-cut methods. The alignment and profile of the Broad Street tunnels were closely constrained by these two adjacent anchors, and in the six-block stretch between them there was very little room for maneuvering. Since the rock ridge petered out about in the middle of the section, it was evident at the outset that there would be about two blocks of rock tunneling at the north end, two blocks of soft ground construction at the south, and two blocks of mixed-face in between. It is this central two-block section that is the focus of this paper.

Jan 1, 1981

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

By M. S. Celik

The principal impurities in some feldspar ores are titanium and iron which impart color and in turn degrade the quality of the ore. The mineralogical investigations indicate that titanium element originates from mainly rutile with small amounts of sphene. Conventionally, fatty acids and particularly sodium oleate are extensively used in the flotation of colored minerals from feldspar ores with reasonable success. In this study, new reagents, oleoyl sarcosine and hydroxamate have been used to float colored impurities before and after magnetic separation. Oleoyl sarcosine is found to exhibit better results compared to fatty acids and hydroxamate. The mechanism of the action is elaborated on the basis of experimental data.

Jan 1, 1999

By Miroslaw M. Hajdasinski

A project&apos;s rate of return (ROR) [The list of all the acronyms used in his text is provided at its end.], be it an internal or external one, usually needs to be approximated. The success and efficiency of an approximation procedure depend on the quality of the initiating parameters such as bounds or seed values (guesses). Current approximation procedures commonly use bounds and guesses dictated by intuition rather then by mathematical consideration. The paper presents three ROR-bounding and six ROR-guessing approaches and examines their suitability on the examples of the typical project cash flow patterns.

Jan 1, 1996