Search Documents

By D. G. Hartley

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balls. For 5 months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm. Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balls. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 22.

Jan 1, 1981

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, the National Institute for Occupational Safety and Health (NIOSH) conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the re-search, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This paper highlights NIOSH?s research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan and if appropriate training is provided.

Jan 1, 2009

By William M. Gray

[The products of mites hive historically beet a very large and important segment of total shipment transported by American Railroads. Much as the Mining transportation Executives right have wished for coal and other mineral deposits to be found along navigable rivers, where railroads have for years been competing with the very aggressive Army Corps of Engineers and the inland waterway operators, the mineable reserves are more often that not located in the arid west far from these "free" waterways. The rivers cannot go to the mines but the railroads could, did, and continue to invest it new lines to reach new mines. The mining industry and the railroad industry have good reason to rely upon each other. The former Northern Pacific Railway, the Great Northern Railway, the Chicago, Burlington and Quincy Railroad and the Spokane, Portland and Seattle Railway merged in 1970 to form the Burlington Northern Railroad, with Lou Menk as its first President. As unofficial spokesman for the industry, be had, for years, conducted a tireless effort to educate shippers, lawmakers and the general public of the single most critical problem confronting the railroad industry, the strangle bold of government regulator.]

Jan 1, 1985

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

Increasing attention is being paid to laterite nickel ore as an alternative to nickel sulfide ore to act as a feedstock for nickel metal production. While laterite nickel ore accounts for a lion’s share of global nickel resources at approximately 72 percent, it accounts for only 42 percent of the world’s nickel production. In addition, the processing of nickel sulfide ore is confronted with enormous challenges due to deeper drilling requirements, higher production costs and depleting reserves. The nickel content in the nickel laterite ore associated with hydrated iron oxides and silicate minerals limits the application of physical beneficiation methods for the removal of iron. Thus, magnetic reduction roasting followed by magnetic separation has been regarded as one of the attractive routes to concentrate and separate the valuable metals from the impurities. 

By R. Gray, B. Hebblewhite

Experience from Australia had identified what is referred to as nonconventional surface subsidence behavior. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence,” and far-field horizontal movements, occurring even beyond conventional “angle of draw” limits. This paper discusses such behavior recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam, leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900 ft to the north, mining at depths of 330 to 720 ft. Investigations, including a subsequent ground movement monitoring program, found a range of evidence in the vicinity suggesting that valley closure and farfield horizontal movements may have occurred, resulting from the adjacent mining. Besides discussing the phenomenon of nonconventional subsidence behavior and the Ryerson State Park case study, this paper includes an assessment of the mining, geology and subsidence impacts and suggested ground behavioral mechanisms.

Jan 1, 2015

By M. Deniz Turan, HASAN NIZAMOGLU, Z. ABIDIN SARI, Tolga Depci

Chalcopyrite extraction in an aqueous acid medium occurs through solid transformations into distinct intermediaries. As intermediates, mineral phases CuS, Cu2 S and Cu5 FeS4 may generate in the leaching solution before CuFeS2 completely decomposes to Cu2+, Fe2+ and S0. Oxalic acid is a common organic acid, and it dissolves easily in warm water. Due to the chelating feature of oxalic acid, it hinders iron precipitation by composing soluble complex anions in a wide range of pH. In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using hydrochloric acid (HCl). Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp= 4.43 × 10 −10) was performed by conventional leaching in the presence of HCl.

By F. K. Spragins

The growing demand and a diminishing supply of conventional crude oil in North America are bringing about an ever increasing interest in the so-called "synthetic fuels". With one commercial plant already in full production, another in the planning and engineering stage, and still others being seriously considered, the Athabasca tar sands is proving to be a leading center of interest. Here, and in the closely related deposits, reserves in place total over 700 billion barrels.1 This major source of new oil is about ready to play a significant role in the filling of ever increasing market demand. When and if fully developed, the Athabasca tat sands could make both Canada and the United States substantially independent of all off-shore supplies of crude for many years to come. Its product, a high-quality, low-sulphur synthetic crude, is beginning to enter the market place at a most favourable time.

Jan 1, 1972

By R. Miller

Lowering our globe’s emissions is a major effort as we move toward a future net-zero carbon environment requiring significant investment in a new, low-carbon infrastructure, along with key market incentives to change. Industry will play a key part in this transformation, requiring expertise in both energy and emissions. Key elements of the de-carbonization strategy are: energy data, emissions reporting method, governance, de-carbonization project generation and drivers, the MACC, electrification, and the de-carbonization checklist. For a zero carbon future, it will be key for business leaders to understand decarbonization, anticipate technological changes, and implement new business me

Mar 2, 2022

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted byproducts generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining, (2) dyke construction schedule, (3) size, shape and location of tailing cells and (4) mining and processing production targets. The results show that in creating in-pit tailing-cell designs, decreasing the mining-cell volume and increasing the number of mining cells improves the net present value (NPV) of the operation due to increased operational flexibility.

By William G. Wilson

In the U.S. today a number of tentative synthetic fuel plants have been sited by a number of major corporations. Each of these for a number of reasons have deferred construction. The only synthetic fuel plants under active development are those being built with the Energy Research and Development Administration (ERDA) under the authority of the Non-nuclear Energy Research and Development Act of 1974 (Public Law 93-577). Under this Act in joint sponsorship with industry, a series of coal conversion pilot and demonstration plants are being built to produce environmentally acceptable fuels from high sulfur coals. Before entering into a discussion of the factors associated with the siting of the ERDA coal conversion program, the difference between a pilot plant and a demonstration plant should be explained. The terms pilot plant and demonstration plant iridicate a size of plant rahter than technology. A pilot plant will vary from an "add-on" to an existing facility to an independent unit. Demonstration plants are a wholly independent, self contained plants, capable of independent operation to demonstrate the environmenta1, economic, and technica1 feasibility of a technology. These plants are from one-third to one-tenth the scale of a commercial operation and often described as plus 1000 tons per day of coal consumption. Their purpose is stated in the Act (Section 6, (3)(E),) "to accelerate the commercial demonstration of technologies for producing syncrude and liquid petroleum products from coal: Provided. That the Administrator shall invite and consider proposals from potential participants based upon Federal assistants and participation through guaranteed prices or purchase of the products .... " In site selection and plant design it has been suggested that special interest groups should be allowed to dictate the site and specify the design. Under the present program the industrial partner who is contributing 50 percent

Jan 1, 1977

By Thomas F. Clemens

This paper covers various changes in government regulations, taxation, and legislation for the past two plus years and the up- coming one. Part of the paper will discuss recent business conditions and how they have affected the cement and lime industry.

Jan 1, 1983

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

By Ewan Alexander

"As human beings, we have managed risk since the dawn of the ages and have been adept at doing so. In order to survive, we hunted or gathered. If we did not take enough risk, we died. If we took much risk, we died (Fig. 1). As individuals and tribes, risk had to be optimized to maximize our chances to thrive, as individuals and as tribes.In today’s world, the risks are vastly different, but in order to thrive, these must be managed. And no industry knows this as much as mining. In fact, the International Council of Mining & Metals (ICMM) has proposed the Critical Risk Model (Fig. 2) as a means of identifying critical risk, critical controls and associated performance standards. The ICMM focuses on sustainable development performance in the mining and metals industry. It has 23 members, representing some of the largest mining companies in the world.This approach is going to help the mining industry. But it must be applied effectively, with the acknowledgment that the system alone cannot be effective. We can say this confidently, as even companies known for the strength of their risk and safety management systems continue to experience significant incidents, and, in some cases, catastrophes. Why does that happen when all safety metrics, including injury rate, are pointing in the right direction? In the view of the author, it is only when leadership, culture and systems work in complete harmony that the resilience of an organization to manage its significant risk is at an optimal level. It remains an ongoing leadership challenge to maintain that balance and the optimal mindset in the organization. So how do you maintain that special balance?Let’s start with a basic premise. Leadership, supported by simple effective systems, creates culture which creates outcomes. Everyone going home safely is an outcome, as is cost effective operations, and to achieve those outcomes efficiently, the organization must focus on the inputs. And those inputs include effective leadership, effective systems (for the purposes of this article, risk and health, safety and environment (HSE) systems), good planning, stable operations and competent workers. This article will focus on gaining maximum performance from your risk management system."

Oct 1, 2016

By T. Dombrowski

Acid-activated montmorillonite is used worldwide as a catalyst and as a sorbent for the enhancement and purification of petroleum products as well as vegetable and animal-based fats. The solid-acid character of the activated montmorillonite is imparted by the manufacturing process, giving it unique properties that are exploited in these industries. Several international companies and a multitude of local clay producers are focusing on improving the efficiency of their standard and specialized products. This paper will describe the use of acid-activated montmorillonite in traditional sorbent applications, as a solid acid catalyst, and other new uses.

Jan 1, 1997

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By CORA ROELOFS

While the COVID-19 pandemic has dominated the headlines, another epidemic in the United States has continued apace — the opioid epidemic. Half a million opioid overdose deaths have occurred in the United States since 1999, when the opioid epidemic began. The causes of the epidemic include the rise in prescriptions for opioid pain medications, including for work-related pain. Miners and other occupations identified as physically demanding and at higher injury risk have been found to be at increased risk for opioid overdose [1]. However, awareness of the risk factors that might lead to opioid use, the potential hazards associated with their use, and resources to prevent addiction and death can allow miners to make choices that can reduce these risks.

By R. E. Cook

"Mineral deposits require substantial amounts of energy to transport and be processed into usable form and, as such, present a real processing challenge in that the deposits are never homogeneous and orebody compositional characteristics are all over the map. Extracting the desired mineral(s) from the deposit at sufficient profit margin, despite severe fluctuations in market price, requires process automation architecture capable of supporting an integrated enterprise solution. Such an architecture will encompasses the activities of individuals, process units, process areas, plant level activities, mine management and business planning, and accounting systems. Key to the automation process is the aspect of value generation. This article brings together the various requirements for the automation of a mining enterprise and presents the different aspects of how to obtain value across the entire mining operation.Minerals’ processing sites are historically long lived, with 20-year life-of-mine not uncommon and 75 years not unheard of. Considering that hardware technology advancements are introduced every six months, or less, it is prudent to select process automation systems that adhere to “open” industrial standards versus proprietary based systems. In the minerals processing industry, the key to survival is driving the cost of production per unit volume to the lowest possible level and provide enough profit to sustain operations. Control system architecture and business information technology are rapidly becoming important tools in the quest for productivity. Getting key dynamic business performance information at the right time to the right person or process unit is crucial to successfully achieving corporate goals. The process automation architecture selected must, therefore, be able to integrate to the various networking enterprises and business systems.The mining industry is generally known as an extractive industry that is physically oriented with respect to operations and the activities in which workers engage. Large numbers of people performing manual tasks in difficult surroundings, produce variable outputs. But times are changing – and so are industry best practices. While the nature of work still consists of activities such as ore extraction, ore movement, ore concentration, refinement and logistics, automation innovations are starting to change the nature of many of the production steps. The industry has transitioned from requiring more physical activities by workers to more information management, automated control and collaboration within the operation. Humans are good at situational intervention and nonlinear reasoning and do best when empowered with an overall production perspective. Machines and automation are good at repetitive functions, steady state operation, and managing transitions. Thus, a combination of advanced technology solutions, reliable and useful information and full human contributions are necessary to mining operations for value generation."

Jan 1, 2015

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

Almost all of the world?s zirconium is mined in the form of zircon (ZrSiO4), the majority as a coproduct of titanium mining from heavy mineral sands deposits. These are placer type deposits, in which the dominant mineral is silica but which also contain a suite of ?valuable minerals,? often consisting of a mixture of titanium minerals, various alumino-silicates and zircon plus a range of other mineral species. The composition of the valuable minerals in such deposits is known as the mineral assemblage. There is no reasonable consistent geological relationship between zircon and titanium minerals. They can derive from separate igneous rock deposits that rarely occur together. The connection emanates once these separate rocks have been eroded by weather and water, often across a very long geological period. Once this has happened, zircon and titanium minerals often find their way to the same locations because they share two major characteristics:

Jan 1, 2011