Search Documents

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By William G. Wilson

In the U.S. today a number of tentative synthetic fuel plants have been sited by a number of major corporations. Each of these for a number of reasons have deferred construction. The only synthetic fuel plants under active development are those being built with the Energy Research and Development Administration (ERDA) under the authority of the Non-nuclear Energy Research and Development Act of 1974 (Public Law 93-577). Under this Act in joint sponsorship with industry, a series of coal conversion pilot and demonstration plants are being built to produce environmentally acceptable fuels from high sulfur coals. Before entering into a discussion of the factors associated with the siting of the ERDA coal conversion program, the difference between a pilot plant and a demonstration plant should be explained. The terms pilot plant and demonstration plant iridicate a size of plant rahter than technology. A pilot plant will vary from an "add-on" to an existing facility to an independent unit. Demonstration plants are a wholly independent, self contained plants, capable of independent operation to demonstrate the environmenta1, economic, and technica1 feasibility of a technology. These plants are from one-third to one-tenth the scale of a commercial operation and often described as plus 1000 tons per day of coal consumption. Their purpose is stated in the Act (Section 6, (3)(E),) "to accelerate the commercial demonstration of technologies for producing syncrude and liquid petroleum products from coal: Provided. That the Administrator shall invite and consider proposals from potential participants based upon Federal assistants and participation through guaranteed prices or purchase of the products .... " In site selection and plant design it has been suggested that special interest groups should be allowed to dictate the site and specify the design. Under the present program the industrial partner who is contributing 50 percent

Jan 1, 1977

By Stefan Medel

As a pioneer Herrenknecht started in 2018 to automate the production of tunnel lining segments. Since then, many automation processes became state of the art. Robots cleaning and oiling the moulds, hydraulic units opening and closing them fully independently. Artificial Intelligence (AI) controls the works and ensures the quality requirements. Data management has become a massive tool from a simple data collector towards a control and optimization tool. Sensors controlling concrete maturity and supporting the precast team to optimize the concrete mix. These state of the art and new innovations will be presented in this paper.

Jun 23, 2024

By William C. York-Feirn, Jeffrey H. Kravitz, David Stalfort

"Mining is an inherently risky business. Over the years, major mine disasters have resulted in the deaths and injuries of thousands of miners in the United States. These disasters also resulted in innovations in approaches to mine design, operations and the training of miners and mine rescue teams. The U.S. Congress responded to these disasters with new laws designed to create mandatory safety and health standards as a means to eliminate fatal accidents; to reduce the frequency and severity of nonfatal accidents; to minimize health hazards and to promote improved safety and health conditions in the nation’s mines.Following a mine emergency preparedness and response holistic gap analysis in 2012, the U.S. Mine Safety and Health Administration (MSHA) identified the need for the development of risk and readiness assessment models for MSHA and the mining industry. MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the mining industry for use at operational levels. In 2012, MSHA hired ABS Group, a recognized industry leader in safety risk management and a wholly owned subsidiary of the American Bureau of Shipping, to develop self-assessment models to help meet this objective.In September 2012, MSHA chartered a project to supply the coal mining industry with a pro-active toolset for mine operators to:1. Self-assess the risks associated with underground coal mining operations in order to prevent major mine emergencies.2. Assess the preparedness of mine operators to respond to an emergency.3. Measure the readiness of mine rescue teams and responsible persons to execute emergency plans.MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the coal mining industry for use at operational levels."

Jan 10, 2018

By David B. Costain

Three dimensional surface approximations are important means of evaluating physical and environmental factors that affect surface coal mining and reclamation. Computer approximated surfaces are projected as an array of square grid cells where individual cells define each parameter value respective to locations on the grid. Grid surfaces or grid cells within a surface can be compared or modified through application of standard mathematical functions. Surface approximations can be used to define the quantity and quality of marketable coal and to evaluate thickness and quality of overburden. Surface approximations also can be used to evaluate overburden swell factors wherein changes in post-mine topographic relief are related to expansion of unconsolidated materials in the backfill. Application of computer approximated surface to analysis of approximate original contour (AOC) standards allows an assessment of the quantity and geographical displacement of overburden and the distribution and numerical level of slope.

Jan 1, 1984

By D. Pappas

Over the past decade, the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry's injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked and injury rate. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992-2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent. Mining Engineering, 2011, Vol. 63, No. 11, pp. 73-79. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By S. K. Kawatra

In most operating coal-cleaning plants, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. Reducing the pyrite recovery first requires that the primary recovery mechanism should be Identified, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not an important mechanism for recovery of liberated pyrite from freshly-ground coal when the collector is a neutral oil, and that the bulk of the floated pyrite occurs either as a result of simple entrainment or by mechanical locking with floatable coal particles. Column flotation results are also presented which show that significant sulfur reductions can be achieved by reducing levels of entrainment.

Jan 1, 1992

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By Shailendra Chawla, Ashok Jaiswal, Sonu

Side spalling/skin failure occurs due to the high-induced stress in underground structures. In such cases, rock bolting or other support systems are being used to control the skin failure or spalling of the pillar. The nature of these support systems is passive, which acts during the deformation. These support systems restrict the displacement considerably of the side/or roof surface of the excavation. Ultimately, it improves the stability of the structure because of the increment in residual strength of rock mass. It is noted that these passive support systems give very low confinement in the range of 0–0.015 MPa at the onset of failure. As the level of confinement will be very low and dependent with progress of failure, triaxial test was not found practically suitable. Thus, an alternative procedure of testing has been proposed. In the procedure, sides of sample have been restricted little bit by using adhesive tape. It provides the limited boundness on the lateral direction (LBLD) of rock specimen. The uniaxial compression strength (UCS) test has been performed on 30 numbers of cylindrical rock specimens using the servo-controlled stiff testing machine. Specifically, two rock types (medium-coarse–grained and coarse-grained rocks) were studied in terms of stress–strain behaviour so that a full residual strength envelope for each specimen was obtained. This study reveals that the residual strength of limited confined rock specimens has been significantly increased as compared to unconfined rock for both groups of rock types. The average residual strength of LBLD specimens of fine-grained rock and medium coarse-grained rock has been increased around 12 times, and five times as compared to unconfined rock, respectively. The average peak strength of LBLD rock specimens has been increased in the range of 30.5 to 48.6% for coarse-grained rock. The results of this study have been presented in terms of peak strength, residual strength and Young’s modulus of rock, and the post-peak failure behaviour of rock specimens was also critically analysed through a stress–strain curve.

Mar 21, 2024

By BERND SCHÖNHERR, JÖRG DEHNERT, PETER WINDISCH, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposure of miners in Germany, especially during remediation work in old mines. The QESS is a lightweight, modular and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil and expanding foam. It is designed to seal off radon-rich parts of galleries within minutes. Originally, the QESS was developed to protect miners against radon exposure. Then, the QESS found the attention of several mine rescue teams at a German mining conference. Some mine rescue drills by The Student Mine Rescue of the Technical University Bergakademie Freiberg, Wismut Mine Rescue and Front Range Mine Rescue helped to improve the system and highlighted its potential for mine rescue operations. Now, the QESS is well-suited for small-scale mining. The QESS can be used to both protect miners from radon exposure and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

By John W. Stevenson

At the No. 4 Mine of Jim Walter Resources in Tuscaloosa County in the North Central part of the State of Alabama, the Mary Lee and Blue Creek coal beds lay 2000 feet below the surface. The quantity of methane gas stored within the coal bed reservoir at this depth and released during development mining necessitates that each coal producing section be ventilated using large air quantities approaching 100,000 cfm. In order to meet coal contractural commitments in the early stages of mine development by installing the necessary number of continuous mining machine units and to develop the mine to projected air shaft sites, high pressure, large volume mine ventilating fans were required. This presentation discusses the installation start-up and changeover procedures when two size GAF 31.5-28-1 TLT-Babcock 3500 Horsepower fans with adjustable pitch in flight blades were put on line while phasing out two Jeffrey Mining Machine Company 8HUA 117 Fans. A graph will be presented to depict the most economic diameter shaft size under 2000 feet of cover with different air quantity requirements.

Jan 1, 1982

By Jeffrey Peterson, John Beesley, Martino Scialpi, John Cassidy

The DC Clean Rivers Project is DC Water's ongoing program to capture and treat combined sewer overflows (CSOs) during rainfall before they reach the District waterways. The Anacostia River system was designed to reduce CSOs into the Anacostia River and includes the Blue Plains Tunnel, Anacostia River Tunnel, First Street Tunnel, and Northeast Boundary Tunnel. A portion of the Anacostia River system was commissioned in March 2018 and the final component, the Northeast Boundary Tunnel, was placed in operation on September 15, 2023. This paper provides a summary of the experience gained during construction of this +$2.9 billion project, an overview of the system performance since its activation in 2018, and a look-ahead to the next phase of the DC Clean Rivers program: the Potomac River Tunnel.

Jun 23, 2024

By P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corporation operates a modern coal preparation plant in Van, West Virginia. Since the start-up of the Van Plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miner's vacation the original system, which included two screw conveyors and a drag conveyor, was replaced by an installation utilizing two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance. The Van facility is a heavy media plant designed to handle 127 mm x 0 raw metallurgical quality coal from the Powellton seam at a maximum feed rate of 590 TPH (metric tons per hour). Depending on mining conditions, the clean coal recovery rate averages between 50 and 65%. The plant is set up with three types of cleaning circuits. Coarse material (127 mm x 12 mm) is cleaned in heavy media baths. Intermediate size material (12 mm x .5 mm) is cleaned in heavy media cyclones. Fine coal (.5 mm x 0) is cleaned in a hydrocyclone1 froth flotation circuit.

Jan 1, 1981

By Bernard A. Grand, Gary A. Almeraris

This project involves the reconstruction of a 1,100 ft. long by 75 ft. wide segment of an existing 4 to 5 track subway under Northern Boulevard in the Borough of Queens in New York City. The project includes widening the existing subway to permit the construction of new inbound and outbound subway (T1 and T2) ramps adjacent to and under existing operating tracks. The plan of the project is shown in Fig. 1. Existing tall buildings along the job site and a contaminated groundwater plume under an adjacent rail yard required construction of slurry concrete walls along the east and west construction limits. Groundwater cutoff across the north and south construction limits of the subway was achieved by jet grout walls built across the subway invert slab between existing track and third rails. The work involved dewatering the construction site to a depth of about 50 ft. below street grade. This is a four year project and includes extensive work to maintain and protect subway and vehicular traffic of over half a million commuters a day through the work area. The project cost was $160,000,000.

Jan 1, 1999

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, the National Institute for Occupational Safety and Health (NIOSH) conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the re-search, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This paper highlights NIOSH?s research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan and if appropriate training is provided.

Jan 1, 2009

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

Increasing attention is being paid to laterite nickel ore as an alternative to nickel sulfide ore to act as a feedstock for nickel metal production. While laterite nickel ore accounts for a lion’s share of global nickel resources at approximately 72 percent, it accounts for only 42 percent of the world’s nickel production. In addition, the processing of nickel sulfide ore is confronted with enormous challenges due to deeper drilling requirements, higher production costs and depleting reserves. The nickel content in the nickel laterite ore associated with hydrated iron oxides and silicate minerals limits the application of physical beneficiation methods for the removal of iron. Thus, magnetic reduction roasting followed by magnetic separation has been regarded as one of the attractive routes to concentrate and separate the valuable metals from the impurities. 

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By R. Gray, B. Hebblewhite

Experience from Australia had identified what is referred to as nonconventional surface subsidence behavior. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence,” and far-field horizontal movements, occurring even beyond conventional “angle of draw” limits. This paper discusses such behavior recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam, leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900 ft to the north, mining at depths of 330 to 720 ft. Investigations, including a subsequent ground movement monitoring program, found a range of evidence in the vicinity suggesting that valley closure and farfield horizontal movements may have occurred, resulting from the adjacent mining. Besides discussing the phenomenon of nonconventional subsidence behavior and the Ryerson State Park case study, this paper includes an assessment of the mining, geology and subsidence impacts and suggested ground behavioral mechanisms.

Jan 1, 2015

By Charles G. Zink

Anthracite is widely known as a domestic or space heating fuel. The prevailing market ratio of domestic to industrial consumption was about 80 to 20 up until 1950. Since then it has been shifting until now the ratio index is about 50/50, exclusive of overseas export. Despite a declining domestic space heating market, the demand for industrial anthracite remains good. However, as a result of stringent air pollution regulations, there is a renewed interest in this low sulphur coal which cannot smoke under any conditions. Anthracite serves other important industries such as power generating, metallurgical, cement, ceramic, chemical, water sewage and industrial wastes filtration. Anthracite is an excellent natural source of carbon and may be utilized in many processes.

Jan 1, 1966