Search Documents

By L. B. Hales

December 3, 1972, James Wm. White presented the results of an instrumentation and process control survey which was sponsored by the Anaconda Company at the annual Tucson Subsection AIME meeting.(1) Twenty-six responses were obtained from questionnaires sent to 48 operating plants throughout the world. The survey results were discouraging in that there were more failures and problems than examples of success. The following quotes are taken from the text of the paper. "We run our mill by the seat of our pants." 'If these blue sky Ph.D.'s (in the instruments and controls area within research) had some operating experience they wouldn't make a lot of the suggestions they do."

Jan 1, 1981

By David A. Summers

Historically, the presence of methane has been a problem, mainly in and around the working areas of active coal mines, and only in these area has drainage been considered. Drainage, where practical, has been achieved through the drilling of holes forward into the coal and the surrounding strata from the working area. These holes generally have been short in length, although where methane drain- age operations around a longwall face have been undertaken, the holes have had to be longer in order to adequately drain from the center of the face into the access gate roads. In recent years, attempts have been made to degasify the coal seams in advance of mining, without disruption of the mining cycle. This is done by drilling much longer horizontal holes through the coal in advance of the working area. Under the aegis of the Federal Government, methods have also been developed for draining seams of coal of their methane content in advance of mining, but from shafts sunk from the surface, without using the active area of the mine as the location for the drill holes.

Jan 1, 1979

By Tom Learmont

The importance of coal in solving our energy problems has been widely discussed; the world demand for food requires increased fertilizer production and the minerals to produce fertilizer must be mined. We have seen an explosive increase in the demand for large stripping equipment. It is appropriate that we review this equipment and determine what can be done to improve productivity. While we have used coal mining as an example in the study, much of the discussion will apply equally to other forms of stripping.

Jan 1, 1975

By M. Nambiar

Due to the remote locations of mining projects and the need for long transmission lines to provide electrical power, mining sites often operate with poor network power quality and low short-circuit capacity. To cope with this situation, more and more mining operators are considering the installation of appropriately designed synchronous condensers together with power factor correction and harmonic filter systems (PFC & HFS). The installation of such power quality equipment is viewed as a technological advancement in the mining application. An adequate level of short-circuit power is essential and has to be ensured for the safe and reliable operation of especially large cycloconverter-driven gearless mill drive systems (GMDs) used for grinding. This paper explores the impact, technical advantage and reasoning for the selection of this advanced hybrid technology to cope with the power system challenges of future mining projects. It also delves into the potential problems and how to address them.

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase the capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont Mining in Nevada was faced with such a need in its carbon-in-leach (CIL) train. In a collaborative effort between Newmont and Derrick Corp., tests were conceived to assess the viability of drop-in replacement screens using a three-dimensional screen panel. The synthetic pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade its urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing and other scalping applications.In spring 2014, Process Machinery Associates (PMA), Derrick’s local area representative, met with Newmont to discuss the operation of the in tank screens in the CIL train at Twin Creeks, near Golconda, NV. The process was originally designed for about 12+ kt/d (13,000+ stpd) but the throughput has been steadily rising since the plant was commissioned. Newmont now requires 14.5 kt/d (16,000 stpd) to be processed. The original screens were running at their maximum capacity, and Newmont required additional screening capacity to continue the upward trend in production.Physical separation by use of screening is one of mineral processing’s oldest methods. Screening media can be prone to blinding and pegging, and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and, thus, larger machines, screening media that does not blind or a combination of both.In an effort to avoid larger machines, Derrick had been working on a revolutionary threedimensional panel that would add nonblinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 in July of 2013. It was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Heather Dougherty, Ted Klemetti, DYKE MARK VAN, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

By Langtry E. Lynd

The titanium industry is based on the unique properties of titanium dioxide and titanium metal. Because of its whiteness, high refractive index and resulting light scattering ability, titanium dioxide in its two main allotropic forms, rutile and anatase, is the predominant white pigment for paints, paper, plastics, rubber, and various other materials. Titanium metal, because of its high strength/weight ratio and resistance to corrosion, is widely used for aircraft, both in airframes and engines, for powerplant surface condensers, and a wide variety of chemical processing and handling equipment. U.S. production of titanium dioxide pigment in 1979 was about 658,000 tons - 2/, valued at about $770 million. Net shipments of titanium mill products were around 19,000 tons, worth about $380 million. These two major uses account for over 96% of domestic titanium consumption. The third largest application, the use of rutile for coating welding rods, required about 9,500 tons of rutile concentrate, worth about $4 million. Other applications of titanium-bearing raw materials include the manufacture of titanium carbides, ceramics, and chemicals, and the recently developed use of ilmenite as a substitute for barite in well-drilling muds.

Jan 1, 1980

By D. M. Hausen

Carbonaceous gold ores are ubiquitous to virtually all of the Carlin-type gold deposits along the Carlin gold belt in north central Nevada, representing the unoxidized "zones" of presumably extinct thermal spring systems of mostly Tertiary age. A period of subtropical weathering resulted in deep sub-lateritic zones in most deposits to several hundred feet below surface. Carbonaceous ores below this supergene profile of weathering have been investigated by various methods, including petrographic study, standard geochemical and organic carbon analyses, carbon and hydrogen isotopic ratios, electron-spin resonance spectra, infrared spectra, and DTA techniques. Results have been integrated with recent findings by other investigators utilizing fluid inclusion and thermal brine data to indicate a first phase hydrothermal solution temperatures and pressures at a minimum depth of 6 km under normal geothermal gradient. This phase resulted in the quartz-barite-calcite vein filling of the host rocks. Gold mineralization took place later at shallower depths. Primary organic material in carbonaceous ores from the Carlin and other mines appears to be a pyrobitumen residue derived from an old oil pool that had been heated by the thermal solutions, and from which the light hydrocarbon fractions were removed. Some of the bitumen was remobilized along silicified veinlets in the ore, but its role in the emplacement of the gold, itself, is not clear. The gold was localized submicroscopically in fine pyrite, mostly in framboids, and as fine metallic particles, but does not appear to be concentrated within the carbonaceous matter per se. However, reducing conditions associated with bituminous residues are believed to have been favorable for gold deposition.

Jan 1, 2013

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By J. E. Dreier, R. E. Scheffel, A. Guzman

"This paper outlines a comprehensive, cost-effective testing program for the acid-ferric sulfate heap leaching of oxide, supergene and primary copper ores. It is based on extensive experience in copper heap leaching and uses the many technological advances in the field developed over the past several decades. The approach described requires firstly a detailed resource evaluation, then a hydrodynamic characterization of representative samples and, finally, a focused metallurgical testing program. The principles communicated here can be applied to other acid leachable minerals. The program varies considerably from conventional testing in its disciplined, orderly, step-by-step approach, its application of hydrological and chemical principles to leaching, and its reliance on fewer, more tightly controlled column tests. The purpose of the test program is to optimize the financial, time and other resources devoted to the program, while minimizing the financial risks to the development company or companies and the project funding providers. IntroductionThe major goal of any process development testing program should be the successful implementation of the project. With respect to heap leaching, the metallurgical testing program plays a critical role in the larger objective, as described in Scheffel (2013, 2014). McNulty’s series of papers (1998, 2004, 2014) confirm that the success of any project is directly proportional to the extent and quality of the testing program on which the process is designed.Therefore, a key development objective is to conduct a well-focused metallurgical test program. While the primary focus of this paper is copper, the acid leaching of any substance would benefit from a similar approach.This paper addresses primarily the sulfate system, which is compatible with the bioleaching of sulfide minerals. Nicol et al. (2011) described the advantages of the chloride leaching of copper sulfide minerals. United States patents Nos. US 2009/0173188 A1, US 8,597,933 B2 and US2015/0232963 A1, assigned to BHP Chile Inc. and BHP Billiton S.A. Ltd, describe methods for both the oxidative and nonoxidative leaching of primary and secondary copper sulfides. Reyes (2013) and Ipinza and Flaquer (2014) described commercial applications of chloride-based heap leaching. The testing disciplines discussed in this paper will also apply to the development of an acidic chloride leaching system."

Jan 1, 2016

By Rolph Linder

It is generally known and accepted that the efficiency of the blast furnace process, expressed by the symbols specific production and coke consumption, is influenced by a large number of variables connected to the type of burden, the alloy contents of the produced iron and the conditions of production as composition and preheating of the blast, the furnace heat losses and the possible use of fuels added on the tuyere level. It is furthermore obvious, that the coke consumption of the process will be influenced by specific production which could be said to be the result of two counter-acting influences. With high production, realized through intensive blowing, the passage time of the ore through the furnace is shortened leading to a decrease of the indirect reduction taking place in the upper part of the shaft within the temperature range of 300 to 1000°C. Simultaneously the external heat losses (constant in time) will be smaller calculated on each ton of iron and the resulting change in coke consumption will be the effect of both those influences. It is certainly of interest to be able to predetermine the effect of those variables before a change in the production practice is carried out.

Jan 1, 1964

By Pramod C. Thakur

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh Coal seam in Northern West Virginia under U.S.B.M. Co-operative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of fourteen, small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by an exhaust fan on surface. The methane capture ratio was poor at 7 to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance the boreholes should be drilled from a point 30 to 45 m from longwall pillar over the largest chain pillar, the standpipe should be grouted for at least 6 m, and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance, and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane-migration towards cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45° ± 10°.

Jan 1, 1983

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electric field (E-field) sensing to send text based communications using two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multi-site evaluation of available TTE systems in an effort to determine their operational sensitivity. INTRODUCTION Wireless, Through-the-Earth (TTE) communication technology is designed to achieve point to point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. This ability allows TTE communication to function without the need for intermediary communications infrastructure, such as repeaters. As a result, such communication systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers 1924; Pittman, Church and McLendon 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker 2006; Wadley 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer 1973; Geyer and Keller 1976; Geyer, Keller and Ohya 1974; Jakosky and Zellers 1924; Large, Ball and Farstad 1973). Although commercially developed TTE systems have demonstrated the ability to communicate through a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker 2006; Geyer and Keller 1976; Geyer, Keller and Ohya 1974; Ilsley, Freeman and Zellers 1928; Jakosky and Zellers 1924; Yenchek et al. 2012)."

Jan 1, 2016

By The SME Sustainable Development Committee

The evolution of sustainable development in mining is recognized as a key contributor to sustainable development (SD), which is defined as the ability of current generations to meet their needs without compromising the ability of future generations to meet their own needs (Brundtland, 1987). This includes, in equal parts, social, economic and environmental impacts ? triple bottom line (Munashinge and Shearer, 1995). Alternately, sustainability has been defined in relation to social, natural, human, physical and financial capital. Our way of life relies significantly on the materials provided by mining, while mining activity affects the triple bottom-line or the five capitals. The mining community and its professionals have come to realize the importance of engaging all stakeholders in the discussion on sustainability. SME, as the leading professional mining organization, has been involved in these discussions. The society has various initiatives in sustainable development for members and stakeholders. The objective of this article is to: provide historical context for current trends in mining and SD and share SME sustainability initiatives ? their goals and rationales ? with the broader mining community. This article is timely because the past year saw two landmark forums on sustainable development: Rio+20 ? the 20th meeting of the United Nations Conference on Sustainable Development, and MMSD +10, the Mining, Minerals and Sustainable Development project 10 years on. Furthermore, this year marks the 10th anniversary of the Milos Declaration on the minerals professional?s responsibilities in achieving sustainable development, forums in which SME was involved.

May 1, 2013

By Jerrold J. Marcus

United states reserves of oil and gas have been steadily declining while consumption of petroleum products has continued to increase. The nut result has been an ever increasing shortfall between supply and demand. This imbalance has been made up by imports of both oil and gas causing a strain on the United States Balance of Payments. To complicate the situation further, exporting nations have recently formed a cartel and dramatically increased the selling price of petroleum products. To meet U.S. energy demand, increased attention has been drawn to the production of synthetic oil and gas from coal. To date, considerable research has been conducted and is continuing on various processes for liquefaction and gasification of coal. Some of these processes are now in the pilot plant stage and at least one demonstration plant has been proposed. The coal conversion complexes envisioned will be very large, requiring substantial capital investments and abundant reserves of coal. Coal production to feed these proposed complexes has been estimated on the order of 75,000 tons per day. With the viability of these projects becoming economically attractive, the Office of Coal Research initiated a contract with Fluor Utah to determine and define the problems of surface mining coal at very high mining rates, under varied physical, geographic, and climatic conditions. The flow of recent events in the Middle East has created a greater sense of urgency for this study.

Jan 1, 1975

By M. Adnan Goksel

The hydrothermal agglomerating process described (U.S. Pat. 3,235,371, (1966)) is different from the conventional high temperature processes. Green pellets or briquettes made with mixtures of moist iron ore concentrates and burned or hydrated lime fines are hardened in an autoclave at 198°C and under steam pressure for 1/2 to 5 hours, with or without previous drying. Under the neutral conditions, oxidation of magnetite does not occur as in the conventional processes. The resulting agglomerates are hard and resistant to abrasion and weathering, and they do not disintegrate in the Linder test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperature and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1968

By B. Anamaeric

Economic, environmental and operational disadvantages of the traditional blast furnace process has led to the development of direct smelting reduction processes, including those that utilize self reducing/ fluxing dried greenballs as iron oxide feed materials. This is mainly due to improved carbothermic reduction, carburization and reaction kinetics. In this paper, the morphological changes of the greenballs as they transform to pig iron nuggets are examined over time at a constant temperature of 1,400° C. The products produced after each treatment were characterized using optical microscopy, scanning electron microscopy/energy dispersive spectroscopy and point counting/image analysis. The changes in the percent metallized area, wustite dendrite and slag matrix content of the structures were calculated. It was determined that the transformations were initially controlled by dissolving and containment of iron oxides in the molten slag and their consequent reduction to iron, followed by coalescence of the metallized areas. The final transformations were controlled by the carburization of the metallized areas.

By John Rajala

The Otjikoto Gold Mill was commissioned during November–December 2014 as Namibia’s first new gold producer in 30 years. Its operations consist of surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and gold recovery. The initial mill design capacity was 2.5 Mt/a. Its capacity was expanded after nine months of operation to 3.1 Mt/a, and process performance has significantly surpassed design expectations. After startup, the Otjikoto Mill’s throughput and gold recovery ramped up quickly, with both parameters exceeding design after only two months of operation. The robust process performance continued into 2019, with key performance indicators (KPIs) eclipsing design values in almost every aspect of mill operation. The Otjikoto Mill’s gold recovery is exceptionally high, exceeding 98 percent every year following startup, especially considering the low-grade nature of the deposit.

By John W. Reddy

The C&NW Ore Dock at Escanaba, Michigan, is a major terminal on Lake Michigan for iron ore pellets arriving from the Marquette Iron Range located 112 km (70 miles) to the north. In an average year, the terminal handles in excess of 8 000 000 Mg (LT) of iron ore pellets consigned to a number of major steel companies. It is important to the steel companies for both cost control and operating efficiency that each cargo be sampled as accurately as possible in order to determine the physical and chemical properties of the pellets. This paper describes the equipment and operating procedures of the sampling facility and Presents some sampling data.

Jan 1, 1985

By W. Burger

For the development of deep, hard rock, mines fast access to the orebody is critical. In some cases the mineralized area is more than 1,500 m (5,000 ft) below surface. Excavation of shafts or declines is typically on the critical path of the project schedule. Saving time on those activities can significantly increase the net present value of the mining project. Mechanical excavation methods are a step-change in excavation performance and labor safety compared to drill-and-blast operations. In hard rock conditions, roadheaders cannot be used effectively, so disc cutting is the first choice. For excavation of declines, tunnel boring machines (TBM) can be used in many cases. These provide, in certain rock conditions, considerably higher production rates com-pared to drill-and-blast excavation. Herrenknecht AG has developed a vertical shaft sinking machine (VSM) that is able to excavate shallow shafts in soil and medium soft rock. The ground is excavated by a roadheader boom. The muck is removed by a slurry system or a pneumatic system in combination with hoisting of skips. These machines have been applied successfully on shafts down to 100 m (300 ft). A pre-sink for a deep mine shaft has been excavated by this technology. For deep, hard rock shafts, a new shaft boring system has been developed by Herrenknecht AG in collaboration with Rio Tinto. Based on proven technologies, the system uses a unique arrangement of existing proven technologies. The system integrates excavation, mucking, primary rock support, installation of the final lining and shaft infrastructure. This new system improves the health and safety of shaft construction. Detailed performance estimates indicate significantly higher shaft construction rates are possible compared to conventional shaft sinking methods.

Jun 1, 2010