Search Documents

By W. P. Diamond

The Bureau of Mines has been investigating several techniques, including the use of horizontal and vertical boreholes, to remove gas from coal in advance of mining. Horizontal boreholes drilled from underground workings as part of the mining cycle have been shown (Finfinger, 1980; Hagwood, 1983; Perry, 1978; Prosser, 1981; Thakur, 1980; VonSchonfeldt, 1982) to be very effective in providing short-term, immediate relief from high methane emissions. This technique has been widely accepted in the coal mining industry, but it does require close coordination to integrate the drilling and subsequent gas drainage and disposal into the projected mine development plan. Vertical boreholes can be placed several years in advance of mining to predrain gas from coalbeds over relatively large areas (Dunn, 1984; Elder, 1975; Lambert, 1980; Steidl, 1978; Stubbs, 1979). The vertical borehole technique has the additional advantage over horizontal boreholes of allowing work to be performed on the surface instead of in the more restrictive underground environment. However, except for the relatively large scale vertical borehole programs for both mine safety and commercial production in the Black Warrior Basin of Alabama (Dunn, 1984; Lambert, 1980; Stubbs, 1979), the technique has been underutilized. The primary reason for this seems to be a combination of the current economic climate in the coal industry, legal questions as to the ownership of coalbed gas, and potential roof damage from the stimulation treatments required to increase the characteristically low permeability of coalbeds to enhance gas production. The question of potential roof damage is the subject of this paper.

Jan 1, 1985

By Don Rose

Steel-fiber-reinforced-shotcrete (SFRS) methods of testing and the wording of specifications vary from country to country. In the USA ASTM C1018 is widely used. The Canadians have taken a close look at C1018 and point out that exact determination of the first crack is very subjective, and they propose a method of design that eliminates this variable. The Europeans (EFNARC) have taken the principles of testing a step further than ASTM C1018, and have added a new step in measuring the effectiveness of SFRS. EFNARC uses an "energy absorption" of a plate loaded in its center, in addition to the principles of C1018. The principles of SFRS design are also used in Japan, Norway and elsewhere.

Jan 1, 1999

By T. Yun

The process automation of coal production is one of the important component parts for achieving the modernization of coal industry. To realize the coal mining process automation serves the significant, function of increasing productivity, improving the quality control of raw coal, making efficient use of mineral resources, saving energy and is of great importance in enhancing the safe operation and improving the labour conditions as well.

Jan 1, 1989

By J. Launay

In order to control and dispatch the sewage water coming from 3 tunnels toward 2 downstream sewage tunnels, a large cavern has been excavated in a suburb of PARIS. Located at a depth of 47,00 m, it has been excavated using the NATM procedure through swelling clay, weathered sandstone, and marl and chalk. It is 16,50 m high, 12,40 m wide and 60, 00 m long, with an elliptical cross-section and its two ends are egg-shapped. The final lining of the cavern is composed of 30 to 40 cm of shotcrete, steel ribs and passive anchor bars. The excavation stages and related movements were surveyed by extensometers, pressure cells and convergence devices. The design, method of construction of the cavern and the results of the measurements made are commented.

Jan 1, 1989

By E. S. Peterson, M. K. Harrup, K. A. Dolbeare, J. E. Wey

Efficient methods for removal of copper from heap leach solutions without mobile organic phases are a current mining industry need. To satisfy this need a selective, high-capacity, durable solid material is required. The INEEL has developed a set of materials based upon current solvent extraction chelates that provide selective copper concentration in the presence of high concentrations of iron. In contrast to conventional solvent extractions, our strategy anchors the chelators to a non-polymeric solid substrate through the use of a custom designed linker molecule. The fundamental synthetic routes to these materials have already been established and attachment to the solid surfaces achieved in an efficient manner. Our continuing research is focused on the optimization of the synthetic pathways to these solid materials and the evaluation of their copper capturing capabilities.

Jan 1, 2002

By Naohiro Kurokawa

Isa Limestone Quarry with an annual production capacity of 18 million metric tons is known as the largest limestone deposit in Japan located in the mountainous region about 20 mile northwest of Ube City, Yamaguchi Prefecture, Japan adjacent to Isa Cement Factory to which it belongs, and which constitutes a mainstay of Ube Industries? cement operating division. Isa Cement Factory is equipped with a N.S.P. kiln of capacity of 3 million metric tons per year, which is the largest of its type in the world. Geographically, it is situated in the south- western tip of the Mainland of Japan (Mid City, Yamaguchi Prefecture) and is bordered by the scenic Akiyoshi Karstic Plateau which is world famous for its huge stalactite grotto.

Jan 1, 1982

By M. Solomon

Crushers are designed and manufactured to survive the severe duty of mining environments worldwide. Under these conditions the crusher performance and availability is one of the critical factors in the mine?s production and profitability. Traditionally the development of these machines tends to be experience-based, incremental improvements in design due to challenges of different applications, duty, or manufacturing. In order to better serve the mining industry a new approach was taken to the design of primary crushers. This approach was to focus on safety and maintenance activities. The result of this effort is a new generation of gyratory crushers that can be serviced from above. Using the features of this new generation of crushers to their fullest extent crushing installations have improved safety, reduced design and construction costs, and lowered maintenance requirements. This presentation explores the benefits of two crusher installations utilizing top service crushers.

Jan 1, 2010

By Jr. Chesson

"Phosphate" is a misnomer as often used. The word is increasingly used to refer to any material containing phosphorus - an element essential to any form of life. Phosphate rock, a mineral - fluorapitate - is recovered from Florida's sedimentary deposits in particle sires ranging from 0.1 to 13.0 millimeter. This product of mining, washing, screening, and flotation is commonly called "phosphate". Its phosphorus content, measured and reported as P2O5, varies from 29% to 35%, and is essentially insoluble. "Phosphate" is also used to describe products containing soluble phosphorus obtained from acidulation of phosphate rock with mineral acids; primarily, sulfuric acid. Many miners have nearby chemical plants wherein phosphate rock is converted into upgraded products such as phosphoric acid, superphosohates, and ammonium phosphates with 45% to 70% P205, soluble and suitable for use as fertilizer. The rock and upgraded products are all commonly called "phosphate"; the plants, "phosphate plants' and the producers collectively are known as the "phosphate industry". The public in Central Florida generally loses identification of the individual operators that include major corporations such as IMC. Williams Companies, W.R. Grace, Mobil, Embark, U.S. Steel, Borden, American Cyanamid and others. They all become just a "phosphate company".

Jan 1, 1978

By R. L. Pozzo

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying the Faraday's Law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a nonmagnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-electrode system involving pyrrhotite, pyrite and grinding media was also investigated as a first step towards elucidating the nature of interactions that occur in the grinding of complex sulfide ores.

Jan 1, 1987

By R. N. Torbin

The degree to which automation, remote control and robotics have been used in the mining industry is far less compared to general industry. Reasons include the adverse working environment, the difficult work operations and the generally lower incentive for capital investments in new mining equipment. The author and his employer has been involved in the development of advanced mining and underground construction equipment. This equipment is designed to he remotely operated, to improve both productivity and worker safety. Many of these machines employ advanced electronics and robotic features. The types of machines that will be discussed include remote shaft lining and placement, remote excavation and mining operations, and automated conveyor systems.

Jan 1, 1991

By David D. Rabb

Leaching or solution mining, a relatively simple and economical process for beneficiating metallic ores, is likely to find increasing application in the treatment of low-grade ores that are impractical to mine by any other means. This process may be carried out in two different ways: 1. Dump leaching, where the ore is moved from its original location to be leached at another site. 2. In situ leaching, where the ore is leached in place by introducing the leach solution at the top, letting it flow down through the ore under gravity, and then recovering it plus the dissolved metals it contains.

Jan 1, 1969

By Gary F. Meenan

The industrial practice of froth flotation for upgrading the quality of fine coal is a relatively complex, expensive, and inefficient process when compared to the coarse- and intermediate-size coal cleaning circuits. The differences in cost and process efficiency can be attributed mainly to the lower equipment throughput, the added cost of flotation reagents, and the fact that flotation is typically a manually operated process susceptible to fluctuating feed characteristics that influence the overall operating efficiency. The emphasis in recent years has been on improving the flotation process efficiency and lowering the cost per clean ton. This has been achieved by larger flotation cell designs, implementation of flotation reagent evaluation programs, and improved process instrumentation and control. These developments are reviewed along with other current coal flotation practices.

Jan 1, 1999

By U. F. Beichmann

INTRODUCTION The City of Oslo together with the neighbor municipalities, Baerum and Asker, are presently building a jointly owned sewage treatment plant located on the west side of the inner Oslofjord. The project is scheduled for completion late 1981. Because the location of the treatment plant is at a distance of about 20 miles (30 km) from the city center, a discharge of more than 13 yds 3/sec (10 m3/sec.) of sewage and storm water will have to be transported over considerable distances. The topography of the area and the geological conditions early indicated that the only realistic transport method had to be through tunnels. As planning proceeded, full face tunnel boring emerged more and more as a favorable alternative to conventional drill and blast medhods. Today the scheme comprises nearly 25 miles (40 km) of tunnels being excavated by full face tunnel borers. In addition a number of access tunnels and cross cuts are to be excavated by conventional methods.

Jan 1, 1979

By Ben L. Seegmiller

The artificial stabilization of a pit slope at the Twin Buttes Mine near Tucson, Arizona has been completed as part of a practical rock mechanics program. The research program began in June 1971 as a result of the three million ton South Slope slide(1) which caused significant economic and operational problems. Hydrological studies, field and laboratory testing and investigation of various stabilization systems(2)occupied the first year of research. In July 1972 a design for an artificial stabilization test using post-tensioned cable bolts was completed and the selection of an outside contractor was made the following month. The project began in mid-September and was completed during the first week of January 1973. The test site is located adjacent to the South Slope slide in a zone of high potential failure. When the site was initially selected it was thought that it would remain stable at least until the test could be completed. However, heavy rains which fell in late October induced displacement in the half of the test site adjacent to the South Slope slide. Prior to this stabilization test it was thought both impractical as well as improbable that a moving slide could be stabilized with an artificial support system(3). Because the project was nearing the half-way point it was decided that an attempt should be made to complete the test as originally planned. This meant, in effect, that an attempt would be made to stabilize the moving section as well as the stable section.

Jan 1, 1973

By Andrew H. Merritt

INTRODUCTION The prediction of the engineering behavior of a rock mass depends upon the systematic analyses of the results of an exploration program, and upon the recognition of the significant rock properties in the early stages of excavation. The variations in rock properties in different geologic terrains and the state of the geotechnical art preclude complete success in the former case, and we therefore must rely heavily on the experience gained in the latter phase. The geotechnical information obtained from these two phases is only of value to the design engineer when applied to the rock behavior during excavation and subsequent plant operation. Pertinent questions which must be answered include: how does the joint orientation and frequency effect tunnel support and overall cavern stability; how does the depth of surficial soil or weathering effect foundations or slope stability for portal cuts; are there permeable zones within the rock mass that could lead to leakage problems around penstocks and is the material in these zones soluble or likely to pipe in the long term; and does the proposed engineering structure fit the terrain, or will it inevitably lead to problems requiring extensive remedial treatment. During the early stages of construction there are two types of geotechnical information required; actual rock behavior with respect to the original design assumptions,

Jan 1, 1997

By R. H. Kuhlman

The purpose of this paper is to describe the roles of cement and concrete in construction in general and, more specifically, as construction materials of the Southeast. For purpose of this discussion, the Southeast will include the geographic area composed. of the following 13 states: Alabama, Arkansas, Florida, Georgia, Kentucky, Louisiana, Mississippi, North Carolina, South Carolina, Tennessee, Texas, Virginia and West Virginia. In one sense, cement by itself is not a construction material. It is a finely ground manufactured mineral product, usually gray in color. Cement is mixed with water and sand, gravel, crushed stone, or other aggregate to form concrete, the rock-like substance that is the most widely used construction material in the world. Because cement is seldom used by itself for construction but is usually a component of concrete, there is no such thing. as a "cement" sidewalk, a "cement" highway, or "cement" building. Neither is "portland" a brand name. It is a generic term used to describe any cement that hardens in the presence of water and is made to standard specifications .. For all practical construction purposes, therefore, all cement is "portland." The name "port-land" was selected by the English inventor of the product in 1824 because concrete made with his product resembled natural building stone quarried on Portland, an English island. Although portland cement is not the final material which finds its way into completed construction, as the principal component of the most widely used construction material in the world, the location and process of its manufacture warrant some discussion

Jan 1, 1977

By Zohreh Kazemi Motlagh, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Five-element style deposits are unusual hydrothermal systems that are typically characterized by a nickel-cobalt-arsenic- silver-bismuth metal assemblage. This mineralization is often represented by abundant native silver, arsenic, or bismuth, and followed by nickel, cobalt, and iron arsenides (skutterudite, safflorite, nickeline, rammelsbergite, and lollingite). The Black Hawk district in Grant County, New Mexico is one of the few examples of this mineralization style in the United States. Despite the differences in formation temperature, depth of emplacement, and host rocks between five-element style deposits worldwide, there are commonalities in mineralogy, ore texture, and composition. A detailed exploration of the native metal and arsenide phases will be performed to compare ore forming fluids between systems and the effects on styles of mineralization and paragenesis, as well as to aid in broader classification of the deposit style. Mineralogy and mineral relationships of the Black Hawk District and other five-element deposits worldwide will be characterized by reflected light petrography, scanning electron microscopy, X-ray diffraction, and electron microprobe analysis. Mineralogical phase diagrams will be generated to better understand the driving processes and evolution of the systems through native metal and arsenide precipitation.

Feb 1, 2024

By L. Donovan Clark

The term "powder factor" is almost universally accepted as the measure of the efficiency of a blasting program. It represents the economics of blasting since it designates quantity of explosive (thereby providing quality control in rock fragmentation) in terms of the associated volume broken. It is the wide use of this concept that explains the interest shown in an approach to rock blasting preferred by A. W. and Z. W. Daw* in a treatise on 3 blasting (1) substantiating its use in the form, Q = CVW3 for single shot hole, where Q = quantity of explosive lb Cv = blasting coefficient W3 = unit volume of rock It is obvious that the term Cv could also be called the apparent powder factor should the equation be written in the form, Cv = Q/W3 (lb per cubic unit). However, while the approach was ingenious** and the practical applications straightforward, their original, rather limited experimental work, along with certain assumptions, was questioned.

Jan 1, 1970

Adsorption of acrylamide based homo and copolymers on hematite was investigated as a function of phe nature of the polymer charge and functionality of the polymer. Effect of addition of sodium dodecylsulfonate and dodecylamine hydrochloride was also studied and was determined to result in an increase or decrease in the amount of polymer adsorbed depending on, the charge characteristics of the surfactant and the polymer, pH of the suspension, concentration of the various species and the order in which these species were added to the system. The surfactant adsorption under given conditions on the other hand, was found not to be affected by the presence of the polymer molecules. The data is analyzed to elucidate the mechanism of adsorption of polyacrylanide type polymers on hematite both with and without the surfactant species king present in the system.

Jan 1, 1982

By Nick Karlin

Dragados USA is constructing the LA Effluent Outfall Tunnel, a 7-mile, 18 ft internal diameter effluent discharge tunnel, utilizing a 21.6 ft (6.585 m) Herrenknecht Mixshield TBM. This paper highlights the means and methods used for TBM launch from a 55 ft diameter shaft excavated in wet with diaphragm wall support of excavation. This included SEM excavation of jet grout blocks for starter and tail tunnels, temporary concrete structures and steel installations, TBM sealing system, umbilical management for TBM hydraulic, electric and bentonite circuits as well as complex segment delivery logistics. The many launching challenges were overcome thanks to the innovative approaches from the project team.

Jun 13, 2023