Search Documents

By John S. Hutchins, David L. Wassum

Mining engineers are ready to take a big step into a new field-oil mining. To understand the subject, one must look at the world's oil supply and demand as well as petroleum technology successes and failures. The US has an abundance of solid hydrocarbon and uranium energy resources, but 75% of its energy for industry, transportation, manufacturing, and space heating comes from liquid petroleum and natural gas. So there are increasing efforts to discover new oil reserves; today the number of drilling rigs operating in the US is at an all-time high. But with 80% of the world's wells already located in the US and Canada, good new exploration prospects are difficult to find. The cost of drilling deep new wells has also greatly increased. The US faced a similar situation in the early 1950s, when primary oil production declines began. During that time, the petroleum researcher introduced secondary recovery techniques such as water flooding and gas injection. This increased the average amount of extractable oil from discovered US reservoirs from 17% to 33%. Production soared and the world petroleum price remained stable until the end of the 1960s. Secondary recovery techniques were then supplemented by tertiary oil recovery technologies-increasing sweep efficiency with such things as CO2 injection-that are, so far, only partially successful in most petroleum fields. Even so, these technologies could raise cumulative recovery expectations to 35-38%. The "lost" oil in depleted US reservoirs equals 48 km3 (300 billion bbl) of conventional oil, or 12 times the current recoverable reserve base. At the present rate of US consumption-1 km3/a or 6 billion bbl/a-this is enough to run the US for 50 years without importing any oil. Moreover, there are 16-24 km3 (100-150 billion bbl) of as-yet unrecoverable heavy oil and tar sands in the US.

Jan 12, 1981

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By J. G. Pippenger

The mining industry has been Australia?s major economic driver over the past decade, contributing 8% to Australia?s Gross Domestic Product and 26% of Australian Stock Exchange Market capitalisation. Australia is the world's leading exporter in coal, iron ore, alumina, lead and zinc; and second largest in gold and uranium. While driving the economy, this resource boom has also created a demand for professional and operating talent that has far outstripped the capacity of Australia?s 21 million residents. I moved to Australia some 10 years ago and have not looked back. This unique island continent with its mix of Indigenous and diverse immigrants ? many still proud of their convict ancestry ? has offered life long memories both professionally and personally.

Jan 1, 2011

By Michele Ashby

The mining industry is facing new risks from peak commodities, the energy and economic crisis and stock market pressures. The Green Mining Industry Initiative is a risk management strategy for the future of the mining industry. Defining the Risks The bad news is peak commodities, energy and economic crisis and stock markets collapsing are the issues that are already hitting everyone?s bottom line and draining the treasuries of every mining company around the world. Higher energy costs are affecting the bottom line more than ever before, which is creating more risk for companies. Mining companies have major land positions around the world and they have major energy needs. Uncontrollable increases in energy costs, increased regulations for diesel fuel emissions and energy intermittencies are costing mining companies more time, money, and man-power, which are cutting into profits and hitting the balance sheet. The good news is, there are practical energy solutions which are off the grid, tried and true methods which can be implemented in a cost-effective manner and will increase profitability and save shareholder values as well as energy security for these companies and their projects. To date, most of the mining resource industry has not yet considered or used other forms of power like clean, sustainable, or alternative energy for their own energy needs. The reasons have primarily been pushback from the mining industry due to beliefs of older technologies in alternative energy, a lack of understanding of the cost advantages long term, and perceptions of environmental relativity.

Jan 1, 2008

By Wayne Trudel, Lloyd McEvers, Lori Clarke, Eric Saderholm, Charles Lynn Bolin, Leroy Schutz

Newmont mine geologists in Nevada are most proficient when applying technical expertise with multi-departmental teams in three main settings. The first is value creation through near-mine discovery, development and reserve conversion. Since 1986, geologists have created substantial net asset value in developing more than 1.35 kt (43 million oz) into quality Nevada surface and underground gold reserves. The second setting is value realization by supporting mine operations with ore control, selective mining, reconciliation investigations and strategic planning. The investment of technical research on reconciliation investigations led to new concepts and practices that highlighted opportunities for large revenue and reserve gains. In 2002, more than $65 million in projected revenue was added to the Gold Quarry south layback. Kriged mine polygon construction and controlled blast heave at the Lone Tree Mine provided millions of dollars in mining efficiencies. High-quality geologic advice in selective mining at the Twin Creeks Mine helped obtain $4.3 million revenue gains throughout 2002-2003.

Jan 1, 2004

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation has been carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Firstly, the effect of temperature on the alkali activation of mine tailings was studied. Secondly, the impact of additives, i.e., calcium hydroxide and aluminum oxide, on the compressive strength of samples was investigated. Thirdly, the impact of forming pressure on sample strength was studied. Test results showed that unconfined compressive strength (UCS) of 40 MPa was achieved with the geopolymerization products through optimization. Finally, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including SEM/EDX, XRD, and FTIR spectroscopy were used to investigate the microstructure and the elemental and phase composition of the geopolymerization products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation has been carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Firstly, the effect of temperature on the alkali activation of mine tailings was studied. Secondly, the impact of additives, i.e., calcium hydroxide and aluminum oxide, on the compressive strength of samples was investigated. Thirdly, the impact of forming pressure on sample strength was studied. Test results showed that unconfined compressive strength (UCS) of 40 MPa was achieved with the geopolymerization products through optimization. Finally, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including SEM/EDX, XRD, and FTIR spectroscopy were used to investigate the microstructure and the elemental and phase composition of the geopolymerization products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.

By P. K. Das, S. K. Singh, C. C. Chang, E. C. Wang, R. B. Roberts

As part of the New York City’s redevelopment of the far west side of mid-town Manhattan, this project will add 1.5 miles of twin bored tunnel to No. 7 Subway Line. The proposed alignment extending from the Times Square Station west beneath 41stStreet turning south under Eleventh Avenue and terminating at 25th Street will include two new stations. The tunnels and station caverns will be primarily constructed in the Manhattan Schist, and will pass in close proximity to several major overly ingstructures. This paper discusses the lithology and structural discontinuities of rockmass along the project alignment, tunnel and cavern rock loading, groundwater hydrology, groundwater quality, groundwater treatment and sustainable design.

Jan 1, 2005

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

By Guosheng Zhan

The Homestake Mine included the open cut and underground workings up to 2,484 m (8,150 ft) deep. The mine ceased mining activities in December 2001 after 125 years of operation. Pumping from the underground workings continued for 18 more months until June 10, 2003. Homestake had completed a comprehensive hydrologic evaluation on post-closure underground flooding prior to the shutdown of pumping. After closure, the mine was selected by the National Science Foundation as the site for the Deep Underground Science and Engineering Laboratory (DUSEL). An interim laboratory facility will be set at the 1478 m (4850 ft) Level. The final facility will be set at the 2256 m (7400 ft) Level or deeper. Pumping from the underground workings began on June 5, 2008 by the South Dakota Science and Technology Authority (SDSTA). During the period of June 2008 through March 2009, the pumping rate increased from 41 L/s (650 gpm) to 81 L/s (1,290 gpm) with an average rate of 60 L/s (950 gpm). As a result, the water level had been lowered more than 95 m (310 ft). It was found that the observed rebound and later decline to date is in close agreement with the model projections. Because of this, the authors of this paper reject claims of a lack of sufficient measurement devices in place and a lack of understanding of the hydrologic system at the Homestake Mine prior to shutdown of pumping in 2003 (Davis et al, 2009). Furthermore, it is believed that this validated model can serve as a useful tool for the SDSTA to manage future underground dewatering for the DUSEL operation. This paper evaluates the hydrologic conditions in the Homestake Mine area and projects the post-closure groundwater rebound and decline due to DUSEL pumping.

Jan 4, 2010

By J. Warmbrodt, D. Apel, D. Nutakor, L. Grayson, M. Hilgers

MinerSIM is an augmented reality system with integrated hypermedia that is suitable for training underground miners in the basics of using a jackleg drill to install rock bolts. While statistical evidence shows that rock bolting with such a drill has an inherent level of risk, it is conjectured that this can be mediated with adequate safety training outside of the actual mine environment using a variety of educational media including interactive three-dimensional images, games, animations, and videos to describe the mechanics of rock bolting and its principles. Ultimately, trainees will install rock bolts in an immersive environment mixed with real and virtual images generated via a gaming graphics engine. This paper will discuss considerations, implementation issues, and evaluation methodologies of the MinerSIM system.

Jan 1, 2007

By B. Comley, M. C. Harris

There is as yet no accepted method of predicting flotation frother performance in plant processes based on laboratory scale characterisation techniques. This paper investigates the use of dynamic surface tension, using the maximum bubble pressure method, as a means of evaluating frothers and frother mixtures. An adsorption model is presented, which has been used to quantify the role of frother type and concentration during frother bubble interaction, based on the correlation of model parameters to physical frother characteristics. This approach was found to provide useful insight with respect to blending and selection of flotation frothers to meet specified flotation performance criteria.

Jan 1, 2001

By Michael R. Walsh, John H. Wright, Eivind B. Jensen

A tunnel boring machine (TBM) was designed and built at the Cold Regions Research and Engineering Laboratory in 1992 for use in Antarctica. The TBM system was tested at the South Pole where a 120-m long tunnel was bored to prove the concept. Modifications were made to the system resulting from this work. In 1999,boring of a 600-mutilidor began as part of the new South Pole Station. Tunneler hydraulics reliability problems prevented the completion of the tunnel before the end of the short construction season. This paper discusses the design and operation of the TBM, proposed solutions to the problems encountered, and current operations of the system.

Jan 1, 2001

To gather additional field data from the western United States, researchers from the National Institute for Occupational Safety and Health (NIOSH) installed an array of field instrumentation at a longwall coal mine in Central Utah. The purpose of this field site was to monitor ground movement and changes in pressure during mining where conditions include massive, stiff overburden and relatively deep cover. To accomplish this, field instrumentation was installed in the two-entry gate road between the fifth and sixth longwall panel in the current mining district.

Jan 7, 2020

By A. Jennings

[ ] In November 2005, Essroc Cement, part of the Italcementi Group, commissioned a long overland conveyor at their Nazareth plant in Pennsylvania. This conveyor, tagged CV-105, was designed to transport 1000 tph of limestone from the quarry to the kiln, and 400 tph of hot clinker (at 300°F) at back from the kiln to a handling facility about halfway back. Conveyor CV-105 is 8969 ft (2733 m) long. It gains 152 ft (46 m) of elevation in the first 1570 ft (480 m), then is mostly flat for the remaining 7400 ft (2250 m) (Figure 1). After the limestone is discharged at the head pulley, hot clinker is loaded onto the return side of the belt. This clinker can be discharged at one of two locations.

Jan 1, 2012

By William R. Yernberg

The 26th Peruvian Mining Convention (Convención de Ingeneieros de Minas del Perú) was held Sept. 15 through 19, 2003, in Arequipa. The convention was sponsored by the Peruvian Institute of Mining Engineers (Instituto de Ingeneiros de Minas del Peru). The Institute has been organizing these events since 1954. They are now held every other year. The conventions spotlight Peru’s mineral resources and have contributed to the tremendous growth of the Peruvian mining industry. This year’s meeting consisted of technical sessions, forums, field trips and social activities. It was held at the Tecsup Institute of Technology of Arequipa. More than 3,000 mining professionals attended. As always, the meeting was well organized, and participants expressed gratitude to the organizing committee for another successful meeting.

Jan 1, 2004

By Reginald Dias

Mining equipment life may be extended through preventive maintenance and the proper application of quality lubricants. There are several practices mine operators should consider implementing to preserve their equipment. An exercise in review — Begin by reviewing original equipment manufacturer (OEM) recommendations regarding servicing and maintenance intervals for each part of the equipment, especially the engine. And the verdict is — If the manufacturer’s recommendations have been followed, good. If not, owners/operators should begin periodic service work on equipment, to help minimize equipment downtime and extend engine life.

Jan 1, 2004

In 1992, the United States economy grew at a rate of 2%. The Gross Domestic Product rose to $5,946 billion. With 257 million people - 635,000 in mining including petroleum - the United States has more than 100 million dwelling units and more than 190 million licensed motor vehicles. New private housing starts rose I 1 % to 1.2 million units. New car production rose 4% to 5.7 million units. Truck and bus production rose 20% to 4 million units. The rate of inflation was 3.5% and the prime rate of interest was 6.25%. The Producer Price Index (1982 =100) was relatively unchanged from 1991 as follows: fuels and related products and power 80, metals and metal products 119, chemicals and allied products 126 and nonmetallic mineral products 117. Energy Imports of crude and refined petroleum, costing $50 billion, rose 3% to 455 Mm3 (2.9 billion bbl). Domestic petroleum production fell 1 % to 582 Mm3 (3.5 billion bbl). Petroleum supplied about 41 % of US energy, natural gas 24% and coal 23%. Coal production, 60% from surface operations, rose 1 % to 914 Mt (1 billion st). About 78% was used to generate electricity and 3% was coked. Exports valued at $4 billion included 57 Mt (63 million st) of metallurgical coal and 39 Mt (43 million st) of steam coal. Ura¬nium mining, including recovery from phosphates, fell 18% to 3 kt (3300 st) U308.

Jan 1, 1993

By Raymond W. Henn

The 31th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, in Golden, CO June 7-11, 2010. The field demonstration portion of the course was conducted June 10 at wlh Construction Co.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods performed under various field conditions.

Jan 1, 2010

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008