Search Documents

By M. Menegaki

Restoration of abandoned mine sites is still one of the weak points of mining practice. The latter stands especially for the case of the surface coal and lignite exploitations, where the extended size of the disturbed land and the drastic changes to the geomorphologic features do not facilitate the implementation of a cost effective and environmentally sound reclamation plan. The paper examines the parameters involved towards the legal requirements for the reclamation of the first lignite exploitation in Greece, namely the ?Plakes? mine, located at Euboea, due to the particularities of the site. Then an integrated redesign procedure is presented, aiming at minimizing aesthetic degradation, confronting technical difficulties and preparing the site to accept new uses.

Jan 1, 2005

By James K. Kindig

Hazen Research, Inc., has developed a new process for removing pyritic sulfur and ash from coal. Feed coal is contacted with iron carbonyl vapors, Fe(CO)5, at 190°C which puts a thin skin of magnetic material on the pyrite and ash, but does not affect the coal. Thus, low intensity magnetic separators yield a nonmagnetic coal, low in sulfur and ash, and a magnetic refuse, high in sulfur and ash. Results are given for clean coal produced by this method. A comparison is made between results of the magnetic process and the U. S. Bureau of Mines two-stage flotation process cleaning identical samples of Pittsburgh Coal. Capital and operating costs of the two cleaning methods are discussed.

Jan 1, 1976

By William Hodder, Ehsan Alavi, Muhib Hussain

Disc Cutter Wear is influenced by several geological and technical factors and excessive wear can have a major impact on the excavation efficiency of Tunnel Boring Machines (TBM). Disc cutter replacement events cause a disruption to the construction schedule and costs, and should be minimized throughout the project to the extent possible. A well-executed cutterhead inspection and maintenance plan can help mitigate abrupt cutterhead interventions and reduce its effect on project schedule and cost. This paper examines cutterhead inspection and disc cutter replacement events as well as subsequent wear data recorded in the first 7km of the 10.3 km long, 6.3 m diameter Coxwell Sanitary Bypass Tunnel (CBT) project in Toronto, Ontario. The CBT alignment is mainly through Georgian Bay Formation shale.

Dec 1, 2022

By G. Castillo, J. Mortensen

"INTRODUCTION Molybdenite is typically produced as a co-product in the copper ore flotation process. At the Rio Tinto Kennecott Concentrator (RTKC) in Copperton, Utah, the molybdenite is initially floated with copper sulfides and other value minerals producing a Cu-Mo concentrate. This is then separated in the molybdenum plant by depressing copper sulfides and pyrite and floating only molybdenite. The molybdenum plant in RTKC comprises the rougher circuit and several stages of cleaning to achieve a certain grade requirement of Mo. The rougher circuit is where the first stage of separation occurs. Cu sulfides and pyrite are depressed in the rougher circuit by adding NaSH under nitrogen and in the cleaner circuit by adding NaSH under air. The depression of Cu sulfides (and pyrite) by NaSH is related to the redox activity1. It is important therefore to maintain a reducing potential in the circuit in order to achieve effective Cu-Mo separation. If the rougher circuit is under air, like RTKC’s molybdenum cleaner circuits, it is harder to maintain the target redox potential because NaSH oxidizes rapidly in the presence of air thereby increasing NaSH consumption significantly. CU-MO SEPARATION AND ROLE OF PULP POTENTIAL The collector adsorption on copper sulfide minerals is through an electrochemical mechanism2. The collector changes the surface chemistry of the Cu mineral allowing it to float. Molybdenite, or MoS2, on the other hand, floats readily in the presence of a frother as it is naturally hydrophobic. Usually, hydrocarbon oil extenders such as diesel or burner oil are added to enhance Mo recovery. In order to effectively separate Cu from Mo, the collector complex on the copper surface needs to be destabilized or desorbed using a reducing agent such as NaSH or Nokes. As long as the circuit is under highly reducing conditions, the collector remains detached from the sulfide mineral surface allowing Cu sulfide depression. Therefore, it is important to measure the oxidation-reduction potential (ORP) continually and maintain the reducing condition with addition of NaSH. For a given collector each mineral will have a characteristic potential or electrochemical window for flotation to occur3, therefore, it is necessary to reduce the potential outside of this window in order to effectively separate Cu and Fe sulfides from MoS2 minerals2. In RTKC plant, the target reducing condition is between -450 to -550 mV to effectively destabilize the collector and depress Cu and Fe minerals. Typically the dosage of NaSH used in the molybdenum plant could range from 6 to 30 gallons/min (gpm). The high dosage of NaSH could pose risk of H2S exposure. RTKC wanted to evaluate alternatives to NaSH in order to reduce its consumption and minimize risk of H2S gas generation."

Jan 1, 2016

By Z. Man, X. Zhu, Y. Xian, Y. Tao

"Fine coal separation has been always concerned. The froth flotation is not efficient in desulfurization because of the low rate of sulfide liberation from raw coal, the natural hydrophobicity caused by sulfur concentration on the surface of sulfide, and the presence of large amounts of middling feed. An efficient centrifugal gravity separator was employed to separate for Shandong –0.5mm high sulphur coal, the partition curve of centrifugal separator was obtained with conclusion that the Ecart probable error value of the separator is 0.095, the imperfection I value is 0.128. Finally, comparing with the coal flotation using progressive release method, the result shows that the effect of the desulfurization with centrifugal gravity force field based on density difference between coal and minerals are much better than that of the floatation which operates based on the difference in surface properties. It provides a efficient technical way for fine coal separation. INTRODUCTION Coal plays the most important role in the energy consumption in China. Although natural gas, wind energy, nuclear power has made great progress in recent years, but the share of coal in the final energy consumption accounts for 70-80%, which is determined by energy storage of China. Under the requirement of environmental protection, the clean utilization of coal resources becomes more and more important, and the need has already been identified. Coal washing and processing plays an important role in the process of high-efficiency and clean utilization of coal. For the separation of fine coal, flotation is a traditional method for effective separation and has been used in large scale industrial applications in coal preparation plant. However, for the separation of difficult-to float coal, especially fine oxidized coal and low–rank coal with hydrophilic surface, flotation is usually inefficient [1-3]. Although many pretreatment methods have been adopted, including grinding, microwave pretreatment, new flotation reagents, the problem of efficient separation has not been completely resolved [4-6]. Thus, an enhanced gravity separation method using particle density difference rather than hydrophobic difference was proposed for the separation of fine coal. Many research results have proved that this is a practical and effective method of sorting. R.Q. Honaker used Falcon C10 concentrator, Knelson centrifugal separator and spiral separator to clean the fine coal with size of 600*210 µm and 210*37µm, the effects of different operating parameters on the separation index was discussed. The results show that the separation density of Falcon can reach 1.6, and the Ep value can reach 0.1-0.15. This paper revealed that for the separation of fine coal with high sulfur content or fine grained content. Falcon has high separation efficiency with low cost. Separation results present in another paper showed that the desulfurization efficiency of inorganic sulfur was better than that of flotation [7-8]."

Jan 1, 2017

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"BACKGROUND The design, development, fabrication, and test of a cryogenic supply for a refuge alternative is part of a larger effort funded by the National Institute for Occupational Safety and Health and managed through a Space Act Agreement with the National Aeronautics and Space Administration at the Kennedy Space Center, FL to create cryogenically based life support equipment responsive to the needs of miners as required by the Miner Act of 2008. This work is done by a joint contractor/NASA team. In particular, the Cryogenic Refuge Alternative Supply System (CryoRASS) serves to provide a respirable air source to miners confined for 96 hours in a mine refuge alternative. This system stores liquid air in a zero-loss cryogenic reservoir (Dewar) until an emergency requires use. The system does not require electric power when in use by miners. Because of the very cold nature of the liquid air, considerable heat stress relief and reduction of humidity is provided in addition to the required replenishment of oxygen. Moderate dilution of CO2 also occurs.INTRODUCTION The design of this new cryogenic refuge alternative supply system (CryoRASS) uses NASA/Kennedy Space Center technology as a development baseline. The design stores cryogenic (liquid) air that is warmed in an air handler box and the resulting gaseous air is introduced to the chamber that not only causes air circulation, but relies upon environmental and human heat to expand the liquid air to a gaseous state. Therefore, the primary benefits of the liquid air source, besides atmosphere maintenance (oxygen), is refuge cooling and dehumidification. This results in reduction of human heat stress and this occurs without the need for electrical power in the refuge chamber. This reduction is a major factor in ""apparent heat"" and the human perception of comfort. Another benefit with introduction of ""air"" vs only ""oxygen"" is the dilution of carbon dioxide. The volume of new air will displace existing refuge air and this air laden with humidity/CO2/low O2 passes out of the refuge relief valves. These RVs should be strategically placed to vent stagnant air preferentially. An initial system test was conducted in our Florida facility in a production 10-person hard chamber for 96 hours. Last year (2014) the system was tested with a 23 person inflatable refuge alternative in Bruceton. For this test, the CryoRASS air handler was redesigned to offer superior characteristics when installed in a Built-in-Place refuge alternative. This report describes the results of the modified system being tested in the Pittsburgh Experimental Mine while attached to a 30 person refuge for 96 (+/-) hours."

Jan 1, 2016

By T. A. Lloyd

The use of tank cells over the years has provided a means for low cost, space efficient, extra capacity in existing flotation circuits. In some cases, new plants have selected tank cells as the machine of choice. Typical tank cells use high efficiency impellers for mixing, which results in low power draw. Unfortunately, these mixers have poor aerating characteristics that compromise metallurgical performance. This has all changed with Outokumpu's new flotation concepts. Outokumpu has recently developed the HG or High Grade flotation cell that can provide higher recovery with better selectivity while maintaining the simple operation of conventional cells.

Jan 1, 1993

By Newell H. Orr

Titanium's performance characteristics in acidic oxidizing and mildly reducing environments make it applicable to numerous currently defined and many projected hydrometallurgical applications. With titanium's current and projected availability and price stability increased use in pressure leach, piping systems and electrorefining is practical.

Jan 1, 1983

By F. M. Benavides

This paper presents recent developments in federal environmental regulations, which in the view of the author, affect mining and the mineral processing industries. This is a summary of activities by the administration, congress and regulatory agencies during 1990. The information presented is a recap from material published. The emphasis is given to Air Quality regulations, although other environmental concerns are reviewed.

Jan 1, 1991

By D. S. Choi

The paper contains a subsidence measurement taken over a room and pillar panel of a mine located in northern West Virginia. A total of 72 monuments were used to determine a three dimensional view of mine subsidence. In addition, the results of measurements were used to compute ground strains with the use of a numerical model.

Jan 1, 1982

"Replacing the century old rail tunnels that run beneath the Hudson River and carry about 200,000 passengers per day between New York to New Jersey has been a high priority for many years. But after Superstorm Sandy hit the east coast of the United States in 2012, the urgency to replace the tunnels increased dramatically. The Hudson Tunnels project is one of nine projects that make up the larger $30 billion Gateway Project. The Gateway Project has been called the most urgent infrastructure program in the country and the Hudson Tunnels is the most critical part of the project, as it will build a new rail tunnel under the Hudson River and rebuild the existing and deteriorating North River Tunnel that connects New York and New Jersey.“Superstorm Sandy proved the level of resiliency of the tunnels, which was not very good,” Amtrak deputy chief engineer structures James Richter told attendees of the George A. Fox Conference in New York City on Jan. 23. Age and corrosive salts deposited by flood waters from the storm in 2012 have affected interior concrete and copper wiring in the tunnels. “Since then, things have been deteriorating and getting less reliable.”Richter, along with Mohammed Nasim, senior director engineering design, both with Amtrak, spoke at the 2018 George A. Fox Conference where more than 350 tunneling and underground construction professionals attended the conference at the Graduate Center of the City University if New York to share insights about the complexities many of them face on daily basis.Under the theme of “Managing construction of complex underground projects: Strategies for tunneling in populated areas,” the one-day conference featured presentations from some of the top minds in the tunneling and underground construction industry. The presentations touched on everything from the highly technical challenges of constructing tunnels through changing geology while working beneath cities and rivers, to navigating the complex financial issues and contracts that come with the projects that have many stakeholders.All of those challenges, and more are part of the Hudson Tunnels project. It is one of the best examples of the full complexities of a complex tunnel project, with the added pressure of securing funding from state and federal government entities under an increasingly tight deadline."

Jan 3, 2018

By Z. D. Hora, W. N. Hamilton

Evaporite units of the Western Canadian Sedimentary Basin are known to host native sulfur. In British Columbia, a large number of oil and gas exploration drilling holes reported intersections with native sulfur. The most important ones include 6 meters (20 feet) and 27 meters (90 feet) of native sulfur among 23 occurrences in Devonian Muskeg evaporite or adjacent Slave Point reef facies carbonates. A small Frasch sulfur deposit is known from Devonian Wabamun Group sediments near Camrose in South Central Alberta. Occurrences of native sulfur are common also in association with presently mined gypsum of Devonian Burnais Formation in southeastern British Columbia. Triassic sediments with evaporite members in British Columbia are also known to contain native sulfur showings. A widespread presence of anhydrite in many sedimentary units of Alberta and British Columbia together with oil and gas fields in the same areas and associated native sulfur occurrences point to a possibility for Frasch sulfur deposits in this part of western Canada.

Jan 1, 1992

By M. Galetakis

The difficulties that rise during the evaluation of multiple-layer lignite deposits come from the deposit structure (alternating lignite layers with intercalated material of varying thickness), as well as from the limitations of the applied selective mining. Thin layers of lignite and interbedded waste layers are grouped under specified assumptions regarding thickness and ash content, to form the exploitable blocks. However, in practice the decision for excavating a block is made under subjective constraints of different importance or by using uncertain data. Advances in Fuzzy Inference Systems (FIS) have provided a new approach to the evaluation of multiple-layer lignite deposits. FIS have the ability to handle imprecise or incomplete or linguistically ambiguous information and to incorporate them into decision-making processes. In the developed FIS (Mamdani type) new linguistic variables, concerning with working conditions, operators? experience and production were involved. The FIS was used for the estimation of quality characteristics and reserves of the exploitable lignite produced from Southern Field mine, Ptolemais (Greece).

Jan 1, 2005

By Joseph B. Gillenwater

Miss Gertrude Carey lived next to us in Martinsburg, West Virginia for several years. She was a retired school teacher. She was also a cousin to Messers Dan and Joe Baker who owned and operated Standard Lime and Stone Company, a predecessor of Martin Marietta Corporation. She-was well acquainted with the Baker family and their history. Here is one of the legends she told my wife, Jean, and me. The Bakers were originally Tanners. They had a tannery near Frederick, Maryland. There were several boys in the family and when they were grown each man had specified responsibilities. Will Baker was assigned the duty of locating, buying, and transporting tanbark and lime. As he traveled through Maryland, Virginia, Pennsylvania, and West Virginia to locate and buy tanbark, he also talked the farmers out of some pieces of lime, which the farmers had produced in holes dug and filled with layers of limestone and wood. Will Baker took the lime and soaked a piece of hide in the milk of lime. If the lime did not spot the hide, Will Baker would get the farmer to burn some lime for him, and further tests would be made. If these tests were good - the Bakers bought the land. They eventually discovered that the limestone that would make lime that wouldn't spot the hide would also be suitable for producing steel. They began producing lime just outside Harpers Ferry, West Virginia in pots and upright kilns. That stone too small for the kilns was just perfect for railroad ballast. Now you know how "Baltimore Blue Bloods" got together!!

Jan 1, 1979

The 6th International Mine Ventilation Congress (IMVC) was held May 17-22,1997, in Pittsburgh, PA. This marked the second time that the IMVC was held in the United States. The first congress, organized in 1975 by the Mine Ventilation Society of South Africa, was held in Johannesburg. Since then, the meetings have been held every four or five years, with the 1979 meeting being held in Reno, NV. This was followed by Harrogot, England, in 1984; Brisbane, Australia, in 1988; and Johannesburg, South Africa, again in 1992. The IMVC provides an international forum in the field of mine ventilation for the purpose of sharing technology and experience. The meetings are attended by ventilation engineers, academics, consultants, government employees and vendors interested in mine ventilation. As was evident from this meeting, significant progress has been made in the field of mine ventilation. However, disasters continue to occur around the world and long-term health problems continue to affect workers. So there is a need for further improvements in ventilation technology. The highlight of the conference was the technical sessions in which more than 80 papers were presented by authors from more than 20 countries. In addition to the technical sessions, the conference featured field trips to a number of mine properties throughout the United States. Five short courses were offered on topics ranging from respirable-dust control to mine fires and explosions. The conference also featured a trade show. It exhibited the latest advances in ventilation equipment, computer application software, consulting and engineering services, and health and safety equipment.

Jan 1, 1997

By S. K. Nicol

The results of column flotation tests conducted on a bulk sample of ultrafines discarded from the fine coal desliming cyclones at the Riverside coal preparation plant of Theiss Dampier Mitsui Coal Limited are presented. A 9% ash concentrate was obtained from a 51% ash ultrafine feed at 75-80% recovery of combustibles in a single stage of column flotation. From this result it is predicted that installation of column flotation at Riverside would lead to the annual recovery of additional coal worth $US5.1M. The operating conditions for coal and copper column flotation are compared and some differences which may result in a variation in column design are noted.

Jan 1, 1987

By Shawn T. Sorrell

Phillips Coal Company (PCC) submitted the first surface mine permit application under the Office of Surface &lining approved regulatory program of the State of Louisiana. This application for the Oxbow Lignite Surface Mine which is located approximately 64 kilometers (40 miles) southeast of Shreveport, Louisiana was submitted in March 1981. The State of Louisiana Office of Conservation, Surface Mining Division, assigned this application number LSM-1, indicating it is the first one submitted in Louisiana history. The permit area for the Oxbow Mine encompasses 6,251 hectares (15,627 acres). Of this total permit area, 5,862 hectares (14,656 acres) were classified by soil type as prime farmland by the U.S. Soil Conservation Service (SCS). Prime farmland acreage in the permit area became a major central issue in our early planning stages and throughout the permitting process of the Oxbow Mine, due to the magnitude of acreage involved.

Jan 1, 1982

By R. D. Hagni

Pyrometallurgical products from lime roasting of refractory gold ores, pyrite, and arsenopyrite have been examined for their mineralogy, porosity, permeability, retention of contaminant sulfur and arsenic, and potential effectiveness of gold extraction. Cathodoluminescence microscopy, supplemented by X-ray diffraction and scanning electron microscopy-energy dispersive analysis study, has shown that the products phases have characteristic cathodoluminescence properties as follows: anhydrite (CaS04), deep blue; unreacted portlandite (Ca(OH)2), deep purple; oldhamite (CaS), light yellow to rarely pink or orange; a sulfur-rich, arsenic-poor phase, violet; an arsenic-rich, sulfur-poor phase, non-CL. Within the temperature range examined (400-850°C), hematite exhibits greater porosity and permeability at the intermediate roast temperatures of 600-650°C.

Jan 1, 1993

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993

By J. H. Meza Viveros

This paper describes some actual parameters and technologies used at Mexicana de Cobre Smelter, and the principal design parameters and new technologies which wiil be used with the smelter expansion project, in order to increase the production capacity of anode copper from 180 000 mtpy to 300 000 mtpy. Likewise its describe some parallel projects under construction also in the smelter plant.

Jan 1, 1997