Search Documents

Relatively lower recoveries (60%) of coarse phosphate (-16 +35 mesh) particles are attributed to the difficulty in transportation of coarse particles from the pulp to the froth column and rapid drainage of these particles from the froth column to the pulp. Increasing the hydrophobicity of coarse particles by higher, more efficient coating of the collector and using larger froth volumes have been suggested to overcome these problems. In this study, the role of emulsification of the fatty acid-fuel oil collector on the flotation recovery of coarse particles was examined. It was determined that emulsification can not only increase the coarse particle recovery, but do so at higher fractions of fuel oil in the collector, thereby reducing the reagent cost as well.

Jan 1, 1989

By B. H. Kim, P. Zhang, M. A. Van Dyke, D. Su, H. Dougherty

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a postmining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64 degrees, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457 m wide and 3657 m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones

Mar 2, 2022

By Yasushi Arai

"Among Tokyo Metro’s approximately 200km of subway lines, the Tozai Line that connects Chiba Prefecture and mid-Tokyo experiences congestion of up to 199% at worst and relief of this has become urgent. Therefore, as it is imperative to increase the number of trains operating in the exceptionally congested area from mid-Tokyo going east, a large-scale renovation work is planned between Iidabashi Station and Kudanshita Station that will facilitate turn-back via 3 tracks. While ensuring the safe and stable operation responsible for about 1.35 million passengers daily, this highly difficult work of inner wall demolition and reinforcement of the side walls and floor slabs will only be implemented for 3 hours during late night. This paper discusses large-scale plans to improve turn-back facilities, and the methods of construction therein as an example of operational improvement of a subway network. 1) INTRODUCTION The Tokyo Metro Tozai Line (“Tozai Line”) opened over the entire 30.8 km distance from Nakano to Nishi-funabashi on March 29, 1969. It has the longest operating length of the nine Tokyo Metro lines, and was the first subway line to extend past the borders of the Tokyo Metropolis. Through train services with two other railway companies are available from the Tozai Line. Tozai Line trains join the Sobu Line of the East Japan Railway Company (“JR East”) and the Toyo Rapid Railway Line of Toyo Rapid Railway (“TR”) from Nishi-funabashi Station, and the JR Chuo Line from Nakano Station. The line is structurally distinctive in that 51% of it was built using the open-cut method, 43% of it is elevated and the remaining 6% was built when we used the shield method for the first time 1)2)3)."

Jan 1, 2016

By Dan Martz, Stuart Lipofsky, Dean Workman

"The Indianapolis Deep Rock Tunnel Connector (DRTC)—first in a vast network of storm water storage tunnels below Indiana, USA—was a wildly successful endeavor. Crews for the Shea/Kiewit JV drove a 6.2 m Robbins Main Beam TBM to world record rates. The machine achieved 124.9 m/day, 515.1 m/week, and 1,754 m/month in limestone and dolomite rock. The advance rates can be attributed to many factors including ground conditions and knowledgeable crew, but continuous conveyors are also of key importance. The novel conveyor system, manufactured by The Robbins Company, enabled continuous tunneling in a difficult layout that included two 90-degree curves and two S-curves. Spanning 11,777 m in its longest iteration, the system included nine booster drives plus a main drive. A vertical belt moved muck up the 76 m deep shaft to a radial stacker for temporary storage. The system, one of the most complex in North America and the first to operate in 90-degree curves, made swift tunneling possible. This paper will examine the world-class tunneling done at the Indianapolis DRTC and the role of continuous conveyance in reaching high advance rates. The logistics of the system will also be examined as it could apply to future tunneling projects with similarly complex layouts. INTRODUCTION The Indianapolis Deep Rock Tunnel Connector (DRTC) is the first phase of a nearly 28-mile long network of deep rock tunnels being built 76 m beneath the City of Indianapolis, Indiana by Citizens Energy Group. The Deep Rock Tunnel Connector (DRTC) Project is a 12.2 km, 5.5 m diameter tunnel constructed by S-K JV, a joint venture between J.F. Shea Construction and Kiewit Infrastructure Co. The tunnel is a $179 million project and is the first segment and southernmost portion of a deep, large diameter conveyance and storage tunnel system to provide overflow relief during wet weather events. The project is estimated to be completed in 2017 and will initially deliver 204,000 cubic meters of the planned 1 million cubic meters of CSO storage for treatment, as well as provide future connections to other tunnels in the overall system (see Figure 1)."

Jan 1, 2016

By C. Maltesh

Anionic conditioning of phosphate ores prior to fatty acid flotation is a very critical step that determines the eventual selectivity, recovery and hence the economics of the process. However the chemical mechanisms operating during this conditioning step are not established. Several studies have been conducted in the past to determine the mode of interaction of collectors with the phosphate fractions however these have been done on a laboratory scale using pure phosphate minerals. In order to test the relevance of the observed effects to plant practice in this work a comprehensive survey of plant practice was first conducted and then adsorption on flotation feed and francolite were studied under simulated plant conditions. Effects of conditioning energy and water chemistry as well as solids loading and fuel oil were determined. Most importantly, different adsorption mechanisms were found to be dominant under laboratory and plant conditions. In plant water, there was some physisorption of oleic acid on phosphate flotation feed and francolite in addition to chemisorption. However, in distilled water under laboratory conditions only chemisorption was detected. Fuel oil reduced the residual oleic acid in solution after adsorption, which explains the beneficial role of extender in phosphate flotation. The dissolved species in solution arising from the flotation feed or plant processing water are shown to clearly play a major role in determining the adsorption of oleic acid on the substrates. The study also specifically demonstrates the importance of conducting research tests under plant mixing conditions and plant water chemistry for the results to be useful commercially.

Jan 1, 1996

By R. G. Robins

The dissolution of metallic copper powder in aqueous solutions of cupric sulfate with ethylene under low pressure was investigated. The reaction stoichiometry obtained was:

Jan 1, 1988

By Russell J. Sheets

Reactivation of highwall slope failures during adverse weather had intermittently impacted haul road access into a previously mined open pit. These impacts ranged from limited access to full closures; however, the greater impact was to an underground mine that was developed within the open pit. Following several significant precipitation events, a rapid snow melts greatly accelerated movements finally closing the haul road and destabilizing other past failures. In addition to re-designing the overall pit access, the decision was made to relocate the primary portal to a more stable highwall. An accelerated surface geotechnical review was required to advance the portal relocation; however, only existing information from past investigation, existing geology model, visual inspections, and slope monitoring data were available for the assessment - no new investigations or data collection could be completed within the allowable timeframe. The evaluation included a review of the geology, an assessment of the current highwall condition and previously observed performance, and a rockfall analysis to evaluate existing catchment above the proposed new portal location.

Feb 1, 2024

By Stephen P. Signer

The U.S. Bureau of Mines is developing an intelligent system for roof' control that uses both an expert system and neural networks to improve the capability of mining engineers to evaluate roof support effectiveness for ground control in coal mines. The expert system com- pares roof support capacities with the support requirements estimated to be necessary to maintain entry stability. It does this by evaluating the results of tests on various types of roof support and establishing the maximum allowable load according to anchorage capacity and yield strength of the support. After the user enters geological information (rock properties, geometry of the opening, in situ stresses, bolt pattern parameters, etc. ), the expert system compares the predicted required loading to the roof support capacity and gives the operator advice on the adequacy of the design and how improvements could be made. A good source of the real-time data necessary to allow the expert system to make decisions will come from a roof bolting machine being developed by the Bureau of Mines. Researchers have collected data from a Western coal mine on drill bit position, penetration rate thrust, torque, and rotation rate. Using this information, two neural net- works were developed to identify different types of strata and features in a mine roof such as rock type, rock compressive strength and joint characteristics. The result is a system that can assist a mining engineer with design information that can be constantly updated as mining progresses.

Jan 1, 1992

By Ekkehart Mertins, Hans-Dieter Wasmuth

During the last years many new concepts have been presented for magnetic separation of feebly magnetic minerals by using the new high-duty permanent magnetic material especially in Open Gradient Magnet Systems (OGMS). In this respect KHD Humboldt Wedag AG developed an improved version of a drum-type magnetic separator called PERMOS® with a special magnetic field configuration for the NdFeB permanent magnets, which gives a magnetic field strength of at least 0.7 Tesla and a wide working zone outside the drum. The magnet system within the PERMOS® unit is no longer made of relatively large magnet blocks of alternating radial magnetisation; the system is now made up of a multitude of small NdFeB bars with a specially oriented magnetisation. This PERMOS® Open Gradient Magnetic Separator can be used for dry magnetic separations in "top-feed" and 'free-fall" feed configuration as well as in the conventional wet "drum-type" feed mode. It allows high throughput rates of up to 40 metric tons of solids per hour and meter of drum length without any clogging problems, even when strongly magnetic com-pounds are present in the feed material. The important design features and the actual machine characteristics of the improved PERMOS® units for dry and wet magnetic separation are described and typical examples for their commercial application for industrial minerals and for martitic iron ores are presented.

Jan 1, 1995

The amount of hydrophobic materials constituting the mineral froth strongly influences the froth viscosity. Higher froth viscosity on the other hand can retard the drainage of physically carried over hydrophobic particles. In phosphate flotation tests a direct correlation was observed between froth viscosity and recovery and an inverse correlation between froth viscosity and grade. Phosphate flotation tests in the presence of a silica depressant indicated that higher froth viscosity is an effect rather than a cause of silica particles reporting in the froth.

Jan 1, 1992

By D. A. Swanson

Predicting when and at what rate seepage will occur from waste-rock facilities is becoming an integral part of permitting and closure at mines situated in dry climates. Such predictions require development of a conceptual framework that accurately describes how water will percolate through a waste-rock facility. Also needed is a detailed hydrological characterization of the waste-rock facility, including measurement of the hydraulic properties of the waste rock and any potential cover materials. This paper presents a conceptual framework describing unsaturated water flow in a waste-rock facility and describes methods for characterizing the hydrology of a waste-rock facility in a dry climate. The methods are designed to collect site-specific data to support accurate and defensible predictions of long-term seepage rates.

Jan 1, 1998

By St. E. Deák

There is a large preoccupation concerning the development of expert tools (ET) in the mining industry, in order to minimize the impact from waste dumps and processing residues on the environment. In this paper, the authors present a new approach for the development of an expert tool for each area under study, in order to minimize production and disposal of mining wastes on the environment, by taking into account the DKRControl method as well as the Ecomining principles, regarding among others hazard identification, impacts and monitoring. Due to the complexity of this topic a reliable ET requires input from a number of interested stakeholders. The design and management of a mining waste disposal site over its entire life cycle is also considered very important.

Jan 1, 2008

By R. Corriveaau

This paper is about a horizontally curved conveyor, which carries 6,050 stph of limestone over land from a new quarry to the owner's plant. The conveyor is 5,012 ft long with a horizontal curve radius of5,OOOft Site conditions made a curved conveyor design the most optimal and economic solution. Using our unique custom conveyor calculation program, TKRI was able to accurately model and design the conveyor to properly track the belt and prevent any spillage through the horizontal curve radius. A data monitoring system was installed that allows monitoring of the conveyor both locally and remotely. The remote monitoring allows TKRI to contact the owner for preventive maintenance. Preventive maintenance can reduce the conveyor downtime during normal operating hours.

Jan 1, 2004

By E. Topuz

Productivity is the most important determinant in the economics of underground coal mining operations. Lower labor productivity increases labor requirements per ton. This, in turn, increases the unit cost of production. Intensive labor requirements may also affect miner injuries and fatalities by increasing man-hours of exposure necessary to produce a given amount of coal.

Jan 1, 1988

By Roy J. Greenfield

A highly undesirable side effect of the mining of coal is the release of acid forming chemicals into the ground water system. The disturbance of the ground during mining allows water to flow through the coal bearing strata and mine refuge where it absorbs iron and sulfide ions and thus becomes highly acidic. The highly acid mine water can then contaminate water supplies and can destroy many of the recreational uses of Pennsylvania's waterways. A great deal of effort has been expended to develop methods of controlling groundwater pollution from mine drainage. At the Pennsylvania State University there has been an ongoing effort to under- stand the chemistry of acid mine water formation and the hydrologic environment in which the acidic water migrates from the mine source into the ground water system. As a support to the hydrologic studies, geophysical studies have been used to help determine the geologic structure of the areas under study which are contaminated by acid water. In addition, the geophysical work has been used to define the type of information geophysical methods can give to determine which geophysical methods are most useful and to develop geophysical field procedures.

Jan 1, 1973

By A. Papandreou

Industrial wastes nowadays constitute one of the most serious threats for the future of our planet. Researchers around the world have very often proposed many kind of solutions in the management problem of industrial effluents. However in most cases suggested solutions are either too expensive to be applied in industrial scale, or they just transfer the problem (e.g. precipitation creates dangerous sludge) and so they create an even greater problem and threat. In the present study the exploitation of valuable hydraulic and adsorption properties of fly ash is studied. Fly ash can easily and cheaply be shaped into stable pellets. After ageing for a sort period of time, these structures can be used as adsorbents for the removal of heavy metals from industrial effluents. Experiments in aqueous solutions have shown excellent adsorption behavior concerning the removal of cadmium, copper, lead, chromium (III) and zinc. The advantage of this technology, except low cost, is that after saturation the pellets can be easily removed from the liquid phase and stabilized in concrete structures without any problem of desorption or leaching. Moreover in these structures a significant amount of cement in the concrete can be replaced by raw fly ash. (Ashcrete as it is called). The utilization of an industrial byproduct as fly ash in the form of pellets as adsorption means and their stabilization with concrete (or ashcrete) combines the useful properties of a solid waste in the treatment of liquid effluents and constitutes a green low cost technology.

Jan 1, 2006

By L. A. Morley

Electricity is a major cause of lost-time accidents and fatalities in the mining industry. Major hazards and unsafe practices that contribute to electrical hazards are identified in this paper. Recommendations for reducing electrical accidents in surface mining are given and are directed toward the following three areas: preventing equipment contact with overhead lines, preventing maintenance related accidents, and defining system protection techniques.

Jan 1, 1986

Paper and paperboard manufacturers need to quantify the carbon footprint and environmental impact of their products to satisfy market, social and government demands. Coated paper products contain minerals, such as kaolin and calcium carbonate, at significant levels; some coated paper grades have mineral contents as high as 45% by weight. Some uncoated paper has no mineral content, but most uncoated paper contains some mineral to improve appearance, process efficiency and cost. Super-calendared paper grades can contain levels of mineral up to 35% by weight. This paper describes how to calculate the carbon footprint of kaolin and calcium carbonate minerals used for white pigments. The carbon footprint of these minerals strongly correlates to the primary energy sources, final product form and energy used to calcine kaolin and lime. Kaolin and calcium carbonate pigments have a favorable impact on the carbon footprint of paper and paperboard products by directly substituting for fiber and by reducing the energy needed for paper making. Key words: Kaolin, Calcium carbonate, Paper production, Carbon footprint, Lifecycle analysis

Jan 1, 2010

By Stephen V. Thompson

Within recent years portable seismic refraction units have found their place in the industry for shallow investigations, Completely portable, relatively inexpensive and of proven accuracy, the portable refraction seismograph is an electronic tool in an electronic age. The age of electronic instrumentation has seen the development of seismic reflection and refraction equipment for deep exploration, especially in the petroleum industry. Large, expensive units, normally truck-mounted and utilizing explosives, are being used successfully for this type of sub- surface investigation. The portable seismograph utilizes the same theory for shallow work as that applied to deep refraction seismology.

Jan 1, 1964

By Ramamritham Sridhar, Vaikuntam I. Lakshmanan, Dan A. Macki

Historically, introducing new technology to the mining industry has been problematic. In general, the industry is reluctant to take risks with new technology because it is already heavily tied to risk, even using existing technology. Risk in the orebody itself can be substantial. The company is dependent on drill hole patterns that are expected to define what is underground, and process test work is often based on drill cores and other samples, which occasionally produce surprises. And even well-proven processing techniques can blindside the producer, resulting in embarrassing and costly difficulties. But if the industry is to grow in knowledge and become more efficient, new ideas must be introduced. How to introduce new technology is the essence of this paper.

Jan 1, 2001