Search Documents

By Philip L. Hageman, Paul H. Briggs

An important tool for use in the geochemical assessment of abandoned mine-waste piles is a leach procedure that can easily be done in the field and used for on-site screening of historic mine-waste material. We have developed a simple field leach test that is an effective indicator of waste pile geochemistry and can be used in order to establish the relative geochemical fingerprint for a given pile. This simple procedure also provides indication of the potential chemical composition of run-off from the weathered surface of these piles. As part of developing the technique, a comparative study was carried out on eight mine-waste composite samples from different deposit types. Splits of all eight composites were leached using the field leach test procedure and a modified version of EPA Method 1312 (SPLP). We found that the field leach test consistently provides relative indication of leachate geochemical trends comparable to leachate data derived from the more regulated, time consuming and laborious EPA Method 13 12 (SPLP).

Jan 1, 2000

By David A. Collins

Red Dome Gold Mine classifies ore types within the pit by gold and copper grades. Copper grades are further distinguished by total copper and cyanide soluble copper levels. At present, Cyanide Soluble Copper samples take six hours of agitating before they can be assayed. This agitation time produces results which are a proportion of the total cyanide amenable copper. This relates to our plant's performance. Frequently the total copper result is needed before we can begin the cyanide soluble copper analysis. This caused a protracted tum around time. Mennetech Pty. Ltd has produced a catalyst proven by David Martin Menne to accelerate the cyanidation of gold. David said that the information at hand indicated that Leach WELL TM also accelerates the leaching of cyanidable copper substantially. Test work was undertaken on-site at Red Dome Gold Mine to investigate the potential of Leach WELL TM to reduce the leaching period and therefore, the overall tum around time required for cyanide soluble copper determinations.

Jan 1, 1995

By Michael P. Foose

In 1994, more than 41 of the approximately 160 coal-fired, electrical- power plants within the six-state Ohio River Valley region used flue-gas desulfurization (FGD) units to desulfurize their emissions, an approximately 100% increase over the number of plants using FGD units in 1989. This increase represents a trend that may continue with greater efforts to meet Federal Clean Air Act standards. Abundant limestone resources exist in the Ohio River Valley and are accessed by approximately 975 quarries. However, only 35 of these are believed to have supplied limestone for FGD electrical generating facilities. The locations of these limestone suppliers do not show a simple spatial correlation with FGD facilities, and the closest quarries are not being used in most cases. Thus, reduction in transportation costs may be possible in some cases. Most waste generated by FGD electrical-generating plants is not recycled. However, many FGD sites are relatively close to gypsum wallboard producers that may be able to process some of their waste.

Jan 1, 1999

By N. B. Aughenbaugh

Compacted, fine-grained soils, often referred to collectively as clays, are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials for these liners include a variety of sand, silt and clay admixtures. These exhibit dramatically different engineering properties when densified. Therefore, it is imperative to adequately assess and characterize any soils being considered for compacted liners. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Because they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners also must include an evaluation of their flexibility. That is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1991

By S. Kelkar, H. Murphy, Z. Dash

Nearly 30 estimates of the minimum earth stress were obtained from hydraulic stimulation tests in 5 boreholes at depths varying from 0.6 to 4.3 km in jointed granitic rock near the Valles Caldera in New Mexico. This site is located within the transition between the Colorado Plateau and Basin and Range provinces. Stresses were determined from open hole hydraulic fracturing experiments conducted with water at pressures up to 48.3 MPa (surface). The virgin bottomhol e temperatures ranged up to 327°C. Pressure records show no evidence of rock breakdown, indicating injection into pre-existing joints. A typical pressure response consists of an early wellbore storage period followed by linear fracture flow, which then evolves into a steady pressure, fracture extension mode. Shut-in behavior is characterized by a sharp pressure drop followed by a more gradual decay. The minimum earth stress shows a general linear trend with depth, increasing with a gradient of 19 MPa/km. A low stress anomaly occurs from 2490 to 3100 m where the minimum stresses are as much as 28 MPa lower.

Jan 1, 1986

By James A. Clum

The shift to lower grade iron ores, e.g., magnetic taconites, resulted in a shift towards agglomeration practices which could effectively deal with the fine particle sizes generated in the liberation and concentration processes. If the iron bearing particles are not extremely fine, e.g., -1/2 in + 100 mesh, sintering is an adequate means of agglomeration.(1) For the more dispersed ores which result in fine concentrates (more than 80%,-325 mesh), the fine particles must be agglomerated by mechanical means before final hardening, e.g., pelletizing.(1) In the pelletizing process, the essentially mechanical step of balling is extremely critical since the strength of the pre-fired pellet determines the firing conditions. The ability of the proper amount of moisture to hold together a ball of the very fine ore concentrate particles has long been recognized. It is a charac¬teristic of the reaction at the interface between the ionic solid of the ore concentrate and the polar water phase which overlays the solids. The strength in such moisture laden balls, the green strength, is a strong function of the water content (Figure 1) and thus deteriorates rapidly for either a small excess or a small deficiency of moisture. For purposes of commercial practice, the control of green ball handling properties by accurate control of ball moisture is too demanding. Moreover, as the ball is heated towards its hardening tempera¬ture, e.g., 1300'C, there is a substantial drying reaction which would lead to such a low dry strength of the ball that it would not support its own weight much less the weight of other balls in a firing furnace.

Jan 1, 1976

By E. De Souza, J. F. Archibald

"Many underground mines use cemented backfill to mitigate environmental effects associated with tailings disposal. The large energy needs associated with mine backfilling and cement production operations create significant CO2 and Greenhouse Gas Emissions. This paper introduces post-consumer glass as an alternate, equally effective and lower cost binder agent strategy for cement in backfill that may be implemented to assist in reducing solid waste production, lowering energy costs, and restricting Greenhouse Gas Emissions. Extensive engineering testing, consisting of pipe flow loop tests and strength tests, has been implemented in order to demonstrate the technical feasibility of process integration within industry. An economic analysis has demonstrated that glass is competitive in cost relative to cement and a socioeconomic study has further indicated that the utilization of glass in mine backfill would create a new market for waste glass that requires less processing and reduces costs."

Jan 1, 2005

By G. V. Henderson

Limestone and Dolomite quarries located near Salto-De-Pirapora, Arroia Grande Gaucho, Conde Francisco and Candioita probably represent the closest, major sources of high quality lime and cement grade carbonate rocks to the major population center of Sao Paulo Brazil. The nearest major city to most of the limestone - dolomite sources is Sorocaba and Palma. All of the mining properties visited during this study are located in the state of Rio Grande Do Sul at approximately -32 degrees south latitude and -52 degrees west longitude, southwest of the major port city of Porto Alegre.

Jan 1, 1981

By Ernest B. Snyder

The word "line" has been used loosely for many forms of the common steel plant flux. For example, many people use the word "lime" for nigh calcium and dolomitic limestone, for high calcium and dolomitic quicklime (also called caustic lime, calcined lime; burnt lime, pulverized and pebble lime) and ;van for clinkered dolomite. Calcium hydroxide, also called slaked lime and hydrated lime, is called "lime" but is seldom used as a flux except when the quicklime air slakes in open boxes or bins. All of the above forms of "lime" are used in the steel plant. Calcium hydroxide is used for water treatment, acid neutralizing, and as a lubricant for wire drawing. All the other limes are used as fluxes in the sintering plant, blast furnace or steel producing furnaces. In the production of self-flux or super-flux sinter, high calcium and dolomitic limestone fines are used. Where quicklime fines are available, they may be added to the sinter mix also. The blast furnace uses both high calcium and/or dolomitic limestone. A few trials have been made using iron oxide stabilized dolomitic lime in an attempt to reduce coke consumption and to increase the production rate. The trials were very successful but would' not be economical, except in periods of coke shortages, with resulting extremely high coke cost and exceptionally high hot metal demand.

Jan 1, 1979

By Armando M. Lago

This paper reviews the postwar changes that have occurred in the expenditure and financial behavior of mineral corporations, and in particular the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample in Section I, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail in Section II. Section III formulates an econometric model of mineral corporate financial behavior which is then estimated and reviewed in Section IV. Section V discusses policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector. Finally, the optimum financial structure of mining firms is discussed in Section VI, which analyzes the effect of corporate financial structure on the mining corporations' average Cost of capital.

Jan 1, 1969

By Frank J. Foster

This Paper will deal with Bucketwheel Suction Dredging and its particular relationship to mining applications. There will be comparisons with other methods of suction dredging and descriptions of two recent bucketwheel installations in the mining area. The Directory of World Dredging Fleets published in the `larch 1984 edition of World Dredging magazine shows that there are about 1.000 conventional Cutterhead Dredges listed throughout the world with 289 in the United States. There are 242 Bucketline Dredges listed throughout the world of which only 6 are in the United States. These figures are not completely accurate because several units are known to the author that are not on the list and, of course, there may be others.

Jan 1, 1984

By A. E. Reisenauer, R. W. Nelson, G. W. Gee

A model assessment was made to evaluate contaminant transport to ground water from clay-lined and unlined tailings pits. The input hydrologic soil characteristics were measured on materials typical of those found at the Morton Ranch uranium mill site in central Wyoming. The assessment involved combined saturated and partially saturated flow and contaminant transport models for two-dimensional cross-sections typical of the proposed Morton Ranch burial pits. Specifically obtained from the models were contaminant flow paths, the advancing contaminant flow fronts for sorbed and non-sorbed constituents, and travel times of contaminants along flow paths. Such results enable evaluation of the environmental consequences for the alternative control methods.

Jan 1, 1980

By Bo Arvidson

SALA MAGNETICS, INC. is now operating a 15 tph continuous high gradient magnetic separator, the SALA-HGMS® Mark III Carousel, as part of a complete mineral processing pilot plant installed at Sala's Cambridge headquarters. The Mark III can generate a maximum magnetic field of 18 kG making it possible to process even weakly magnetic, finely ground ores and ore tailings on a continuous basis at the performance level achieved in Sala's cyclic high gradient magnetic separators. Test results on iron ores, clay, and decoppering of molybdenum concentrate will be discussed. Bench scale tests have been performed on all of these materials using the SALA-HGMS® Model 10-15-20 Cyclic Magnetic Separator. A direct correlation may be made between cyclic and carousel results. Sala's Mark III Carousel high gradient magnetic separator is designed to permit scale-up to machines capable of processing two hundred (200) tons of ore per hour and more.

Jan 1, 1976

By David V. Fitterman, David L. Campbell

We've used direct current resistivity (DC), electromagnetic (EM), induced polarization (IP), and ground-penetrating radar (GPR) geoelectrical methods to study mine dumps. The results reflect lithology, pore water saturation, and dissolved solids in the pore water. If the pore water has a pH less than 5, conductivity maps can indicate acid generating potential. IP measurements can help distinguish mineralogy in mine dumps, especially concentrations of sulfide minerals. EM and DC can help locate acidic/high TDS groundwater associated with mine dumps. GPR methods failed at the sites we studied in the West. Our own conclusions are augmented by those from the recent literature.

Jan 1, 2000

By Henry Brehaut

The International Network for Acid Prevention (INAP) was formed in 1998 by 17 international mining companies to promote significant improvements in the management of sulphidic mine materials and the reduction of liability associated with acid drainage through knowledge sharing and research and development of technology. Since its inception two panels have been formed to identify and move forward with research projects and eight networks have been constituted to initiate interaction and knowledge sharing within the membership in specific areas of technical interest. An INAP web site has been developed to facilitate the sharing of information and to encourage the exchange and development of new ideas.

Jan 1, 2000

By D. A. Stanley, B. J. Scheiner, P. M. Brown

The Bureau of Mines (USBM), US Department of the Interior, has developed a method of dewatering clay slurries based on flocculation by high-molecular-weight polymers and water removal from the formed flocs using a trommel or hydrosieve. The exchange ion on the clays affects their dewaterability. Metal ions in solution and on the exchange sites of smectite clays are known to act as Lewis acids. Recent work has determined that these ions can be titrated with high-molecular-weight polymers. The relative acidity of the exchange ion and the basicity of the polymer determined by the new method give insight into the dewatering mechanism.

Jan 1, 1990

By Timothy J. Napier-Munn, David M. Weedon

A model of mineral liberation was developed using back calculation techniques to determine breakage/liberation parameters in a similar manner to the way breakage parameters are determined in the Population Balance Model (PBM). Comminution and liberation data was collected from grinding mills operating at Pasminco lead/zinc mine Broken Hill, and Mt. Isa Mines copper concentrator, Mt Isa, Australia. Laboratory scale single particle breakage tests on ore samples from these sites were undertaken using a twin pendulum breakage device. Break- age/liberation parameters were then determined for several mills using back calculation techniques. The liberation/breakage parameters were then used to simulate mill liberation performance under varying conditions.

Jan 1, 1996

By S. Helgen, C. Byrns, A. Davis

The 4000 acre historic Robinson Mining District outside Ely, Nevada hosts a continuum of oxidelsulfide waste rock dumps of different ages. In an effort to develop a paradigm to explain past, existing, and future conditions at the site profiles of oxygen, pH, temperature, and specific conductivity were collected from various waste rock dumps using a hand-driven soil gas probe and a down-hole sampling device. The resulting data are useful in interpreting the fate and manner of pyrite oxidation within the dumps and in identifying waste rock dumps that may require remedial measures compared to those that require only minimal action prior to closure.

Jan 1, 2000

By Guido Deissnann, Jennifer L. Kirkaldy, Stephan Kistinger, Carol M. Pettit

Contaminated mine drainage presents a potential hazard for aquatic ecosystems and groundwater resources. Reliable predictions of long-term developments in seepage quality are necessary to select reasonable decommissioning options and remediation measures for waste-rock heaps during mine closure and/or mining site rehabilitation to minimize future risks and environmental hazards. Extensive geochemical modeling work was used to assess the consequences of various remediation options for waste rock heaps at a former uranium mine in Eastern Germany. The predicted contaminant discharges are used for an assessment of long- term benefits of decommissioning alternatives to derive conclusions for sustainable remediation measures using risk-based cost/benefit analyses.

Jan 1, 2000

By Norman F. Sweeney, H. John Hovland

Over one million yards of granite were excavated for the Helms Pumped Storage Project, including a large underground powerhouse complex. Site investigations and in situ stress measurements were essential elements of the project design and provided the necessary geologic parameters for executing a finite element study of the powerhouse. A construction monitoring program, of geologic mapping, field instrumentation, and rock mechanics testing was then designed and has been successfully implemented. This paper reports on the scope of this construction monitoring program and explicitly compares the measured deformations to those predicted. As a result of this recent field experience the assumptions used in the finite element program are reexamined.

Jan 1, 1981