Search Documents

By A. D. Davis

A ground-water flow model was developed to simulate the post-mining recharge rate at the Belle Ayr surface coal mine in the Powder River Basin near Gillette, Wyoming. State regulations of Wyoming require that reclaimed lands should provide a rate of recharge that approximates the pre-mining rate. Steady-state calibration and transient simulations showed that the post-mining recharge rate in backfill is at least five centimeters per year, exceeding the original infiltration rate of 0.4 centimeters per year to shallow, overburden aquifers. Major reasons for the increase include the flat topography of reclaimed areas and decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate less than five centimeters per year but somewhat greater than the pre-mining rate.

Jan 1, 1995

By M. Springett

Organization of teams for rapid and effective evaluation of international mining properties requires special considerations beyond those needed for domestic activities. Experience, technical ability, a sense of perspective, humor and self-discipline are vital characteristics to look for in the selection of individuals for forming an efficient and productive team.

Jan 1, 1994

By Paul E. Scheerer

Synthetically produced magnesium hydroxide serves as the precursor for much of the magnesium oxide produced in the world today. Magnesium oxide, in a variety of physical and chemically reactive forms, is a very important commodity. It is used as the main component in refractories employed in steelmaking furnaces and in many base metal refining furnaces. In the chemical industry, it serves as a raw material in the production of epsom salts, rayon acetate, oxychloride and oxysulfate cements and magnesium sulfonates. It is a minor component in fertilizers and animal feeds. It serves as the starting material for producing fused magnesia, used as an electrical insulator in electric heating elements. It is employed in the magnesium sulfite process for pulp digestion in the paper industry. Additional uses are in SO2 scrubbers, as a neutralizing agent in the tanning industry and as a component in rubber compounding. Magnesium oxide is produced not only from synthetically produced magnesium hydroxide. It is produced from natural magnesites, natural brucites, and natural and synthetic hydro-magnesites. Synthetic magnesium hydroxide, as a starting material provides more control of the chemical purity and chemical reactivity of resulting magnesium oxide products because of the uniform nature, chemical and physical, of the hydroxide that can be produced. Synthetic magnesium hydroxide is produced by precipitation of Mg (OH)2 from magnesium chloride bearing seawater or natural brines through the use of a base such as Ca(OH)2 or NaOH.

Jan 1, 1978

By T. B. Szwilski

ISO 14000 series are voluntary international standards that address environmental management system standards, environmental auditing, environmental labeling, environmental performance evaluation, and life-cycle assessment. An environmental management system (EMS) is a facet of an organization's structure that addresses the immediate and long-term impact of a company's products, services, and processes on the environment. Many companies in the United States are taking a cautious wait-and-see approach before embracing ISO 14000. A few mining companies are reviewing the standards and using them as guidelines. The paper outlines the status, possible benefits to the mining industry, and options available to a company wanting to become involved in the ISO 14000 standards.

Jan 1, 1997

By P. Grotjohann

In processing heavy mineral sands, the low feed concentration and respective high value of the desired minerals require high capacity production and sharp classification/separation techniques to reduce the specific production costs. The allflux® separator, a new process system introduced to the heavy mineral industry, meets these criteria in an economical way. Its two-stage process, a combination of rising current and fluidized bed technology, allows the treatment of extremely high massflows in a single unit. Using concepts that have proven successful in processing concrete sands for many years, testwork in coal, iron ore, and heavy minerals looks very promising.

Jan 1, 1998

By J. M. Ekenes, C. A. Caro

"New approaches that increase hydrometallurgical recovery from refractory minerals in below mill cutoff -grade sulfide copper ore can add significant value, improve profitability and increase ore reserves. This paper describes the development and implementation of an engineered heap (EH) approach to leaching low-grade, chalcopyritebearing ore at Freeport-McMoRan’s mine in Morenci, AZ. The technical evolution of the engineered heap concept is described together with the challenges and benefits following implementation. Introduction The Morenci ore deposit, located in eastern Arizona, has been mined for copper for 140 years. Mineralization in the Morenci district consists of sulfides and oxides. To process these ores, Morenci operates concentrator and leaching circuits. Leaching accounts for two-thirds of the copper produced in Morenci. More than one-half of this leaching-derived copper production comes from run-of-mine (ROM) stockpiles. The largest category of material moved in Morenci is destined for ROM stockpiles and waste dumps. Materials that are not economic to mill or leach are designated “waste.” However, this designation can change based on improvements in extraction technology and commodity prices. Chalcopyrite does not leach well due to its refractory nature. For predominant chalcopyrite mineralized ore, copper recovery during a typical leaching cycle may be as low as 5%. For this reason, chalcopyritedominant ores below mill cutoff grade have historically been classified as waste. By incorporating advanced leaching technology to improve metal recovery from previously leach-resistant ore types such as chalcopyrite, the Morenci Mine has been able to reclassify substantial amounts of this “waste” to “ore.” Process chemistry Chalcopyrite copper extraction is temperature, oxygen and ferric dependent. The temperature is achieved primarily by pyrite oxidation (Eq. (1)) and secondarily by oxidation of chalcopyrite itself (Eq. (2)). The regeneration of ferric in solution can be enhanced by providing the appropriate acid and oxygen levels according to Eq. (3). In the absence of microorganisms, this reaction is very slow."

Jan 1, 2015

By A. D. S. Gillies

The provision of a suitable working environment in deep level mines requires the accurate prediction of the ventilation heat load. Mathematical models for predicting strata heat load have been under development since the 1930's and 1940's. Computer models for predicting this and other mine heat sources have been developed and refined over the last 20 years. Some empirical studies have occurred and there is an increased emphasis on the importance of underground studies. Any theoretically or empirically determined predictive method must of necessity make assumptions. Underground space with its irregular configurations and rough wall surfaces cannot be described by simple mathematical expressions. Some heat loads, such as machinery, may occur intermittently while others such as the influence of water evaporation are very difficult to quantify accurately. Current popular models for predicting mine heat load have been surveyed. In testing some of these it is often found that each estimates significantly different quantitative values for the expected load in a particular underground space under study. These differences are explained by the assumptions, simplifications and omissions implicit in each of these models. It would be easier to estimate conditions at any point if heat flow into mine air passageways could be described by simple equations with associated statistically-based confidence ranges. Use of probability distributions to indicate confidence ranges allows any heat level estimate to be expressed as a range of values with limits for maximum and minimum expected values. This approach allows many of the limitations of the popular predictive models to be overcome. A heat prediction method using this approach has been developed based on Monte Carlo simulation and tested on mine data from a number of operations. Heat flow levels which can be predicted by simple equations supported by probability distributions allow the engineer flexibility in adjusting a predictive model to the underground characteristics appropriate to the mine site under study. The influence of all heat sources present in the mine opening must be included. Prediction methods must be updated as mining systems and machinery change with time. Heat sources interact with one another and the system must therefore be understood in its entirety.

Jan 1, 1987

By Carter Brown, Kate Brown Requist, Eric Lutz, Moe Momayez, Athira Satheesh

New mining health and safety training modalities are becoming increasingly prevalent in the underground mining industry. Various digital training tools have been developed over the past several years, but the extent of their use remains unclear. Advances in gamified training by way of computerbased video games and virtual reality (VR) have opened a new avenue for mine rescue and self-escape training, but these methods have not been widely adopted across the mining industry. Mine rescue and self-escape situations require a mix of in-classroom training as well as live drills, but it is important to assess the extent of and effectiveness of new training modalities. The Mine Rescue and Self-Escape Survey (MRSES) was distributed to underground mining operations to collect perceptions of current training effectiveness as well as willingness to adopt new training methods as a complement to live rescue drills. Responses from the MRSES indicate that adoption of digital training technologies has been slow-going despite an interest in their use. Further, there appears to be no meaningful connection between more frequent escape and rescue training and feelings of emergency preparedness. With relatively little use of already developed digital training tools but an interest in their adoption, it may be time to reassess current emergency preparedness training philosophies.

May 1, 2025

By M. J. Beus

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a full-size shaft are underway.

Jan 1, 1999

By John H. Smith

Because of increased pressure from Federal & State Regulatory Agencies, most acid flows will require some sort of treatment prior to being discharged to receiving streams. In many industries, the volumes of liquors are large and their acid content varied. Pressure to minimize costs of waste treatment equipment and land usage makes development of a treatment process incorporating these desires mandatory. "Standard" methods of acid neutralization with lime have been known for years, however, the volume and characteristics of the resultant precipitated solids can create a disposal problem. Also, when standard lime treatment is used, the settling characteristic of the precipitated solids is normally slow. In some instances, the necessity of added dissolved solids removal, (such as iron, needing aeration) add to the problem of concentrating neutralized solids. In a paper published in the September 1970 issue of "Coal Age," *the results of extensive test work by personnel of the Homer Research Laboratories of Bethlehem Steel Corporation, Bethlehem Pa., were reported. This paper dealt specifically with development of a flow sheet to treat acid mine drainage (hereafter referred to as AMD) from coal mine operations. Regulations on discharged water required basic pH and low dissolved iron content after treatment. Liquid flows of over 9 MGD from

Jan 1, 1972

By R. Flattery, Z. Agioutantis

Coal and rock pillar design is critical not only for mineral extraction but also for the safety of the mine operators. Pillar strength can be estimated through numerous empirical formulas that are available in the literature, which are typically based on a statistical analysis of case study data. The limitation of most of these equations is that they only considered the width to height ratio and in situ rock or coal strength for pillars in horizontal seams. The adoption of such equations to estimate pillar strength in inclined seams may overestimate the pillar strength and ultimately lead to a poor pillar design. This paper will discuss different techniques that can be used to estimate pillar strength in inclined seams as well as present preliminary modeling results for stress redistribution around inclined pillars. Factors in the parametric analysis include pillar shapes, geometry, and seam inclination.

Mar 2, 2022

By C. C. Stewart

Jim Walter Resources, Inc. operates four underground coal mines in Alabama. In 1986, during longwall recovery operations, sparks from a torch ignited methane that migrated onto the face after a roof fall. The fire quickly spread to the gob at the tailgate end of the longwall. The fire was successfully "area" sealed and mining operations resumed after five weeks. However, several problems were encountered during this process. This paper describes the events following the fire, methods used to control the situation, problems encountered, and steps taken to ensure preparedness for any future occurrences of this type.

Jan 1, 1993

By Stryker Magnuson

While probe drills are not strictly necessary for all projects, the incorporation and use of probe drills and pre-grouting adds capability and insurance to boring operations. Water ingress and unstable ground can be resolved before becoming a problem and resulting in costly delays through the use of enhanced, 360-degree probe drilling setups. To do this, proper design of the array of drill ports in the shield, matched to the possible ground conditions, is critical. For ground with exceptional water and instabilities expected, additional probing locations are low-cost additions that can lower risk and increase efficiency. In this paper we will look at recent and ongoing projects including the Lower Meramec Tunnel and Jefferson Barracks Phase 2. We will detail the design of those probe drill arrangements, and our overall recommendations for probing/grouting systems that best suit challenging ground conditions and keep projects running smoothly.

Jun 13, 2023

By R. L. Loofbourow

The Sunro Copper Mine is near the south coast of Vancouver Island about 35 miles west of Victoria. Failure of the roof of a large open stope let a good sized mountain stream into the mine. Broken are, boulders and sand were washed into the underground mill and out through a 7 800-foot adit. The adit became plugged; water burst out an a ridge above the adit, washing out the portal and o trestle by which it was reached, Rock and ore are strong but several systems of steep, pronounced but generally tight fractures are found on and parallel to the walls of the orebody. The stope was started from a slusher drift 390 feet below the bed of the River and brought up to an elevation 155 feet below the River by blasting vertical and horizontal rings of longholes in the nearly vertical orebody. Mining was stopped there and five months were given to grouting and bolting the pillar under the bed of the River, During this time and for several months thereafter sloughing increased the width, length and height of the stope. At the last known observation the stope was 77 to 96 feet wide, 185 feet long and the highest point of the domed back was only 55 feet below the River. The flooding took no lives. In other respects, however, it might be difficult to find in mining lore o more savage example of the application of "Murphy's Laws".

Jan 1, 1968

By Peter B. Lilly

I appreciate the opportunity to tell you something about Kerr-McGee's Galatia Mine in Southern Illinois. This new underground mine was a departure for us since our previous experience had been gained in large surface mines in Wyoming. Although we were new, we did have the corporate experience in the operation of deep uranium and potash mines in New Mexico and Wyoming, and an earlier underground coal mine in Southeast Oklahoma. In arriving at our final design, we evaluated numerous concepts and finally settled on a two seam mine sharing a single shaft and slope. The mine, in turn, would be supported by a heavy media processing plant designed to optimize the yield from either seam. Further, we wished to be able to keep the two seams separate so that we could sell either seam separately or in a blend. Due to the thickness of the coal, the practical area dedicated to the mine provided forty to fifty years operations at the selected mine capacities. It was important, therefore, that our design and selection of hardware and systems provide for long life and low maintenance in order to compete in today's competitive markets.

Jan 1, 1984

By A. D. Paananen

With the demand for higher grade feed by the American steel industry and the depletion of the direct shipping ores from the Marquette Iron Range and elsewhere, there was a need to develop the low-grade orebodies. The large reserve of fine grained oxidized iron-formation at the Tilden Mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Preceding the present mining-concentration-pelletizing complex, about 6,500,000 long tons of direct shipping siliceous ore were shipped from the Tilden Mine. Following development of the concentrating and pelletizing flowsheets, engineering and construction was initiated to develop the mine and construct concentrating and pelletizing facilities to produce 4,000,000 LTPY of pellets from this low grade crude ore. Operations started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleveland-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling-Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Due to the non-magnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden orebody have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of des liming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions.

Jan 1, 1978

By M. S. Celik

Adsorption of sodium dodecylsulfonate (SDS) and dodecylaminium hydrochloride (DAH) on Buller seam coal, New Zealand, have been studied. Both surfactants adsorb effectively on the coal below pH 8, and the adsorption isotherms established at pH 4 are essentially the same at lower concentrations. These findings suggest that the adsorption of these two ionic surfactants on coal is controlled by a hydrophobic bonding mechanism. However, the results of calorimetric studies suggest that coulombic attraction also plays a part in the adsorption mechanisms. It has also been found that both the SDS and DAH adsorbed in the first monolayer are not removed by lowering the surfactant concentrations in the bulk solution.

Jan 1, 1993

By Peter N. Loncar

Most miners dream of finding a gold mine sometime during their mining careers, but not very often do such dreams come true. On the tenth day of September, 1962, our dream of finding gold came true when the results of the third drill hole were received. This was undoubtedly one of the most exciting days of our lives. Little did we realize then that this was the beginning of a major discovery destined to became one of the largest gold mines in the country. Discovering and mining gold is not entirely new, however, to Eureka. County a old Lynn Mining District in northeastern Nevada. Since 1900 there has been sporadic activity, mostly consisting of small lode mines and placers. These have produced totally about $300,000; and existence of our orebody would probably have remained unknown had it not been for the United States Geological Survey. The USGS extensively mapped the Roberts Mountain Thrust and published a paper indicating that mineral occurred along this fault and in some places was gold bearing. Utilizing this information, our Newmont Exploration geologists located an area in which: drills were brought in to test their theories. By keeping flexible in our thinning and working, we were able to bring a raw prospect to a producing mine with ore reserves of eleven million tons in a short three-year period.

Jan 1, 1965

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By Jodi Banta

In an effort to reverse the trend of declining enrollments to mining engineering programs that began in 2015, the University of Arizona has implemented a number of interventions over the past five years, including ramping up its pre-college mining education and outreach, and undertaking several enrollment research projects. This article is the second of two installments to discuss the results of our latest study. The first part can be found in the September 2025 issue of Mining Engineering magazine. To better understand mining’s competitive position, the School of Mining Engineering and Mineral Resources conducted a comprehensive study to determine: 1. How prospective college students, parents and educators perceive the industry, related careers and the mining engineering degree. 2. Factors affecting students’ choices of degrees and career plans. 3. The roles parents and educators play and how they influence students.

Nov 1, 2025