Search Documents

By A. Bruynesteyn

Many papers 'have been publihed on the role of the bacterium.Thiobacillus ferrooxidans in the oxidation of reduced sulfur compounds, and years of research have established the following environmental factors, which influence biological oxidation. 1. Oxygen is required for the oxidation of reduced sulfur compounds to the sulfate form. Sufficient oxygen. is available from the air, consequently, it is of importance to get the air to the bacteria. 2. The bacteria are active in the pH range 1.4 3.5. Maximum activity occurs at pH 2..0 - 2.8. 3. -In order to allow the bacterial populations to expand, certain essential nutrients must be available. Nitrogen has to be supplied for the production of body protein, and ammonia is the source most readily accepted by the bacteria. Carbon dioxide is the only utilizable source of carbon and the small amounts available in air are the primary source of this element. Small amounts of phosphate, manganese,, potassium,. calcium. and magnesium are also required. These trace minerals are available from the water and host rock in sufficient quantities. 4. Water is required as a carrier for the oxygen carbon dioxide and other nutrients, as-well as a solvent for the metallic sulfates produced. The bacteria are motile and the water allows the bacterial populations to spread:: bacterial activity ceases if the equilibrium relative humidity drops below 100%. 5.-optimum bacterial activity occurs at temperatures of 34 - 35°.C (93 -.95° F). All activity ceases above 45° C. At lower temperatures, activity its dramatically decreased, but there is still a significant amount at 10 - 11° C.- Thiobacillus ferruoxidans has been isolated from a mine with a year round temperature of 3° C. 6. Unpublished results from our laboratory show that biological leach ore oxidation takes place during the rest periods at the same rate as during the wet leaching periods providing there is a film of moisture remaining around the particles. Optimum conditions can be readily achieved in the laboratory, but application of our laboratory knowledge to commercial leaching dumps is riot as simple. Attempts to achieve improved environmental conditions for the bacteria in leaching dumps would require substantial capital investment and careful planning of leaching operations. This paper

Jan 1, 1972

By D. L. Romero

The Line Creek Mine is operated by Crows Nest Resources Limited, a wholly owned subsidiary of Shell Canada Resources Limited. It is located approximately 25 km north of Sparwood in southeast British Columbia (refer to figure 1). The Line Creek coal deposit is part of the Upper Elk Coalfield in the East Kootenays. The coal is a medium volatile, low sulfur, bituminous coal and is used as a coking coal. Coal close to the outcrop is typically of low F.S.I. and is processed for thermal use. The present pits have a total coal reserve of 30 million clean tonnes and is a multi-bench, open-pit operation. The coal is recovered by front shovel and backhoe combination, and hauled to the plant with a fleet of 120-tonne and 40-tonne capacity trucks. Line Creek is unique in that it can simultaneously treat both metallurgical and thermal coal in separate processing facilities (refer to figure 2). Run-of-mine coal is delivered to the truck dump. The plus 50 mm material is scalped off and reduced to minus 50 mm in two rotary breakers. The raw coal is then conveyed to one of five, 5000-tonne capacity, silos. Typically one silo is used for thermal coal and four for metallurgical coal (refer to figure 3).

Jan 1, 1991

By R. L. Lewis

The White Pine Mine is the second largest active underground copper mine in the United States, covering an area of approximately 34 km2 in the Upper Peninsula of Michigan. A numerical flow model of the White Pine Mine was constructed to evaluate engineering controls that would reduce the rate of mine water discharge after closure. Of the passive controls evaluated, the placement of low-flow bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35 percent.

Jan 1, 1996

By H. Ban

Triboelectrostatic separation tests were performed on a bench-scale, analytical separator using coal, coal combustion fly ash and mineral samples. Fractions of separated samples were collected and analyzed to characterize the performance of the separation. Particle size distribution and morphological characteristics for these samples were analyzed by optical microscopy, and scanning electron microscopy (SEM). It was found that smaller size fractions of a fly ash sample had better separation than the full sized parent fly ash sample, indicating interference or particle-particle interactions during the separation process. It was also observed experimentally that small kaolin particles attach to the surface of large silica spheres, causing charge neutralization and subsequent low separation efficiency.

Jan 1, 1997

By R. L. Grayson

Following lip on a USBM-sponsored research project, the authors have utilized the knowledge-base structure and system concepts from the Sun Sparcstation-based worker scheduling system of the Mine Management Support System to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, their availability on a shift, and work priorities for a shift as well as to allocate manpower optimally on a work shift and delineate supervisory training responsibilities. The various components of the software are described in detail, along with enhancements made to the original system.

Jan 1, 1996

By L. Berwick, A. Karunanayake, D. Skutt, H. Heath, J. Wang

Thallium (Tl) is a highly toxic heavy metal, soluble over a wide pH range. Tl levels may exceed discharge limits in mining-influenced water associated with processing gold, lead, cadmium, zinc, and copper ores. In this work, the effect of sodium permanganate (CARUSOL® C liquid permanganate) on Tl removal from mining wastewater was studied. Factors influencing Tl removal, namely permanganate dosage/demand, coagulant and flocculant use, order of chemical addition, and co-existing metal ions were examined. The results show that permanganate addition is very effective at removing Tl to below target limits and can provide a unique solution for improving wastewater quality and optimizing overall treatment costs. In addition, several on-line monitoring techniques were evaluated for process optimization. The Hach DPD Free Chlorine method was optimal, allowing plant operators to rapidly and easily spot check effluent samples for excess permanganate dose.

Mar 2, 2022

By S. K. Mohanty, T. M. Dittrich, M. J. Allen, M. Dardona, A. C. Strzelecki, J. Hovey, Boukhalfa. H.

Rare earth elements (REEs) have many critical uses in advanced technology and the lack of a reliable domestic supply has been identified by the US DOE as a vulnerability to US economic security. Our research focuses on developing an economical process for extracting REEs from coal fly ash and power plant wastewater sludge by coupling a hydrothermal extraction process with the engineering of a ligand-associated media for concentrating REEs from the extraction liquid. Ash samples have been collected from two Detroit-area Power plants that burn 100% low sulfur coal (Trenton Channel) or fuel blends of 75% low sulfur coal and 25% high sulfur coal or 70% low sulfur coal, 15% high sulfur coal, and 15% petcoek (Monroe Power Plant). Ash samples are then subjected to hydrothermal conditions from 100-350 °C for 1-24 h at Los Alamos National Laboratory and leachate concentrations are measured by inductively coupled plasma-mass spectroscopy (ICP-MS) and compared to hydrofluoric acid digestion results. Experiments designed to aid in ligand selection and loading optimization show that di-(2-ethylhexyl)methanediphosphonic acid (H2DEH or DIPEX™) can be successfully loaded to a commercially available swellable organically modified silica (SOMS) media. Preliminary results show that DIPEX-associated SOMS surface loading can exceed 4x on a mass/mass basis and in simplified sorption experiments with Nd solutions (~pH 2), the DIPEX-SOMS media can sorb >90 mg Nd per g of media. Recovery of the sorbed Nd with low pH solutions has had low efficiency with the high (4 g DIPEX/ g dry media); however, near complete recovery was achieved with lower surface loadings (0.05 g DIPEX/ g dry media). Column experiments are being conducted to evaluate the optimal ligand/media ratio for repeated use. Completive sorption with Fe and other major cations are also being evaluated.

Jan 1, 2019

By Greg Bold, Mahmood Khwaja, Yuannian (Jerry) Wan, Michael S. Schultz, William Simcoe

Beaver Creek Clean River Project will satisfy the consent decree requirements by capturing and treating combined sewage overflows. The project consists of, approximately, 2,700 feet of 30-inch trenchless pipe installation, a new screening/disinfecting facility, an expansion of an existing diversion structure, and a 72-inch internal diameter, 530-foot long mined tunnel. The tunnel portions are being progressed as early release packages. This paper presents the geotechnical exploration program and the subsurface conditions encountered; interpretation of the geotechnical conditions; and, approach to developing stand-alone packages for the tunnels to mitigate construction and schedule risks and continue to advance the project.

Jun 13, 2021

By Anne Kathrine Kalager

"Stretching from Norway’s capital, Oslo, to the city of Ski, a new railway line is under construction with a 20 km long hard rock tunnel. This is a major project with high demands regarding quality, cost and schedule. In addition, restrictions concerning locations close to sensitive urban infrastructure require execution with the highest level of precision and expertise. The new double track railway line forms an important part of the intercity rail development southwards from the capital and includes the longest railway tunnel to date in the Nordic countries. With its novel methods and solutions, this project offers a model for future railway project developments in the region. This paper provides general pertinent details and facts relating to this current railway project and includes a description of the project with information relating to concept and design of the tunnels, geological conditions, particular challenges, selected tunneling techniques and contracting strategies. THE FOLLO LINE PROJECT The Follo Line is a new 22 km long double track railway line under construction between Oslo Central Station and the city of Ski. The project is divided into four subprojects, as shown in figure 1. The main part of the project consists of a 20 km long hard-rock tunnel, which will be the longest railway tunnel in the Nordic countries to date.The Østfold Line is the existing double-track railway line running between Oslo Central Station and Ski serving 12 local stations. The new Follo Line will offer a direct service, without stops, between Oslo Central Station and Ski and reduce the travel time from 22 minutes to 11 minutes. After completion of the Follo Line, these two railway lines will, in combination, more than double the capacity for train transport in the region south-east of Oslo."

Jan 1, 2016

By Eric Gilmore, Ron Tudor, Gregory E. Korbin, Bill McCormick, Brad Bush

INTRODUCTION Las Vegas has recently been termed the “Construction Capital of the Country”. It has also been acknowledged as the fastest growing city in the country for several years running. The rapid growth improves the economic picture of the region but it also imparts unusual demands on the area’s infrastructure. In 1994 the Southern Nevada Water Authority (SNWA)was working on a master plan to address the rapid growth. A long range analysis revealed the need for additional water treatment capacity and delivery systems. Short term projections showed that the current system would reach capacity in the summer of 1997 with the possibility of demand exceeding the supply. The River Mountains Tunnel #2 is part of a $150M scheme to quickly upgrade the system to meet the short term demand, improve the overall system operation and allow for a smooth transition into the larger additions being planned for the future. The SNWA selected Carollo/Black & Veatch (CBV) to provide detailed design and construction management for the upgrades. The River Mountains Contracts consisted of five separate contracts broken out separately to stream line a very aggressive (just 34 months) design and construction schedule. Necessary work included four miles of excavated and lined tunnel, connections from existing pipelines to and from the new tunnel including large diameter (to 3.66m(144 in)) valves, a 18 927cu m (5 million gal) regulating reservoir, a surge tank and a 170 343cu m (45 million gal) reservoir to add additional storage to the system. Notice to Proceed was given to Kajima Engineering and Construction (Kajima) on May22, 1995 for the construction of the River Mountains Tunnel #2. The design called for a tunnel to be driven 6070m (19 915ft) in rock and lined to a finished diameter of 3.71m (12.17ft).Excavation began on December 14, 1995 and holed through on April 30, 1996. Lining began on June 25, 1996 and a notice of Substantial Completion was issued on December 13,1996. This paper describes the measures taken to complete the tunnel in 18 months from Notice to Proceed to Substantial Completion. THE RIVER MOUNTAINS SITE The River Mountains are a low range of rugged mountains separating the Las Vegas Valley from its main supply of water, the Colorado River at Lake Mead. They are volcanic in origin and the harsh desert environment has left them as expanses of exposed bedrock rising 305m (1000ft) above the valley with little or no vegetation. An existing 3.05m (10ft)

Jan 1, 1997

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By Alizeibek Saleimen Nader

The intensive use of computers for mineral application at Serrana's phosphate mine in Jacupiranga, State of Sao Paulo, Brazil, began in the late seventies. The early hardware and software available are described in sufficient detail to allow comparisons between that solution and the new one, based on a personal computer and a new software package - PC MINE SYSTEM from GEMCOM SERVICES INC - that provides full color graphics capabilities plus mine design and planning tools. The process needed for adaptation to the new technology' and its impact on SERRANA S.A. DE MINERACAO are described. Finally, future enhancements to the System and mine control and planning are focused.

Jan 1, 1989

By J. M. Keane

The Solution Mining review arrived too late to appear in the May issue. Solution mining, in its broadest definition, includes all forms of leaching where a lixiviant solution is brought into contact with a metalliferous or non-metallic ore and the resulting pregnant solution is processed for recovery of the valuable soluble material. Technologies such as dump leaching, heap leaching, stope washing and in situ lixiviant solution injection and recovery fit into this definition of solution mining. A publication entitled the US Gold Industry (Dobra and Thomas) reflects the major impact that solution mining techniques have had on precious metal recovery. In 1989 (the last year for which statistics are available), the United States passed Australia to become the third largest gold producing country in the world after South Africa and the Soviet Union. It is estimated that when the final figures are in for 1990, the US will probably pass the Soviet Union in gold output. If the state of Nevada is ranked as a separate country, it will rank fourth in the world in gold production for 1990. A good proportion of this increase in gold production over the past few years can be attributed to the application of solution mining technology to low-grade, precious-metal-bearing material. Solution mining techniques have also made inroads in copper production. Many operations located at former underground mine sites employ in situ leaching as an adjunct to conventional dump and heap leaching practices.

Jan 1, 1991

By T. D. Rourke, E. J. Cording, O&apos

INTRODUCTION Detailed investigation of a 60-ft-deep excavation in a mixed profile of sands and stiff clay was performed by the University of Illinois for the Washington Metropolitan Area Transit Authority (METRO). The work was coordinated through DeLeuw, Cather and Co., the General Engineering Consultant of METRO. Instrumentation was concentrated in a portion of braced excavation for the Gallery Place Station near the intersection of 7th and G Street. The early construction date, the 60 ft depth of cut, and the proximity of large buildings formed the basis for selection of this site as the focal point of observation and measurement. A history of lateral and vertical displacement is provided wherein movements which occurred during excavation to the full depth of cut and, subsequently, during station construction and the removal of braces are described in detail. Observations of preloading and the consequent brace loads and wall displacements are described. The effect of temperature change on brace loads is discussed and the measured apparent earth pressure for the 60-ft cut is provided. The paper discusses the relationship of lateral displacements of the cut wall to the construction procedure, and compares the lateral wall displacement with both lateral and vertical movement in the surrounding soil mass. Based on observed movement, the method by which displacement was predicted for a nearby 82-ft-deep excavation is described. The performance of the 82-ft-deep excavation has been summarized elsewhere (2).

Jan 1, 1974

By H. EI-shall

In this paper, the results of a fundamental study involving zeta potential and turbidity determinations of solid suspensions are discussed. Illustrations of how these results are utilized to design field applications of solid grade polymers to clarify mine drainage water are presented. Other applications in different industries are also reported. The operational and economical advantages are examined.

Jan 1, 1994

By H. J. H. Pieterse

This paper highlights the mineralogy of the Barrick Goldstrike Mines Inc. area. The mine is located at the north end of the Tuscarora Spur and is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend. The Betze, Post, and Meikle Mine are major deposits located in the area. The deportment of gold, its leachability, and various process options are also evaluated. Particular emphasis is given to the practical and economic considerations of ore control, and routing of ore to a process option.

Jan 1, 1993

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

By L. H. Monaco

"The evolutional process is always about solving existent problems in order to provide further achievements. But the more something evolves, the more challenges it faces towards greater evolution. Industrial automation systems in Mining have also evolved a lot in the past decades, but they now face new challenges about integration: how to integrate different locations and systems, in a way to reduce costs and increase overall mine efficiency and safety for the operation. This paper compares conventional mining process automation architectures vs. a state-of-the-art, completely integrated system using Electrical Integration based on IEC 61850 standard for Substation Automation Systems. Emphasis is placed on the benefits to manage the entire mining plant as a whole, not only looking at the production rates, but also at the energy consumption for each part of process. In addition, it is discussed how an integrated system approach unlocks safety and productivity gains such as overall process optimizations, improved operator effectiveness, increased plant availability, and reduced maintenance costs. INTRODUCTION The world is constantly changing, and evolution is a natural part of mankind history. The role of evolutional process is to solve existent problems, but usually these solutions create new issues that need to be addressed. This scenario is also applicable to the industrial environment, in which the demand for higher profitability and efficiency on their processes requires solutions with more productivity using less resource. This is not different when it comes to energy consumption: how to optimize production rates and reduce energy costs at the same time? Regarding automation systems, the trend for the industries is to focus on four main challenges: how to provide safety for personnel; how to reduce initial investment for new plants; how to connect remote and in harsh locations; and above all how to deal with the lack of integration between several systems."

Jan 1, 2018

By G. W. Luxbacher

With the advent of acid rain legislation included within the Clean Air Act Amendments of 1990, a great deal of uncertainty with regard to price, source and production quantities has been cast into the coal market. Powder River Basin and other western coals continue a rapidly accelerating migration eastward, South American coals move into the northern markets, states propose legislation to assist utilities in complying with the new regulations in hopes of maintaining their own coal industries, while some utilities question the long term availability of eastern compliance coal. Any major coal producer must make decisions now to assure their continuing presence in the market place; several companies have adopted a strategy to acquire eastern compliance reserves while others have invested in technology to compete as a low cost producer. This paper discusses some of these options in light of the uncertainties of the market place, from an eastern coal producer?s viewpoint.

Jan 1, 1992

By I. Yu. Melekestseva

Two types of hydrothermal massive sulfide fields were discovered in the Mid-Atlantic ridge (MAR) in the last twenty years. The first type associates with basalts and includes the TAG, Snakepit, Broken Spur, Lucky Strike and Krasnov hydrothermal fields. The second type is related to ultramafic rocks and represented by the Logatchev, Rainbow and Ashadze hydrothermal fields. In 2007 a new, probably, the largest cluster of hydrothermal massive sulfide field on the MAR (Fig. 1), related both to basaltic and ultramafic rocks, was discovered at 13°31'N of the MAR (Beltenev et al., 2007). [ ]

Jan 1, 2008