Search Documents

By E. D. Hummer

During the planning phase of the fine coal cleaning addition at the Gary Coal Preparation Plant, careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at 1/4 inch, pumping the minus 1/4 inch raw coal to bowl desiltors for desliming, and then cleaning the disliked raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 foot diameter thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh Today the minus 48 mesh refuse at Gary consists of thickened flotation tailings and thickened spiral classifier overflow. The transportation of large quantities of fine wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds

Jan 1, 1965

An incremental-analysis-based stope design and cutoff grade calculation method was developed for an underground metal mine project. Traditional stope design methods are typically very time consuming and lack consistency and accuracy by manually drawing stope shapes. For quick reserve calculation and economic analysis, a new method named "3D incremental analysis based stope design" was created for mine-wide stope designs. The key idea of this method is to replace engineers' manual checking of each incremental ring with one calculation of all the rings, and to build the final stope shape with the maximum values. This process was realized through a 3D ring grid setup and proper naming conventions for rapid calculations. With this unique but practical method, multiple options for a mine design were completed within a short time before the final selection of optimal cutoff grade and best stope designs for the project.

Jan 1, 2012

By R. W. Brann, R. C. Freas

Franklin Industrial Minerals operates several mines/quarries, including two room and pillar underground mines. Both of these mines are operated as multiple level room and pillar including heading and bench operations on one or both of the levels. This paper focuses on Franklin’s Crab Orchard, Tennessee mine, which produces both high purity chemical grade limestone and crushed stone for construction applications. The high purity chemical specifications for the chemical grade limestone and filler/extender applications are inconsistent with the non-chemical rock being produced to supply the crushed stone market. As a consequence Franklin has developed a unique mine plan and operation to maintain both product balance and a safe and stable working environment.

Jan 1, 2003

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By C. Roos

Traditionally within the mining industry, the main functional process flow for resource and reserve evaluation proceeds from geologists who build the geological model, to resource estimation geologists (modelers) who estimate the grades, to mining engineers who develop the mine design and schedule. The interface between these three disciplines is not always seamless. Assumptions made during one stage of the process are not always communicated down the line, even though most mining companies have procedures in place to encourage communication across the various disciplines. These procedures do not always achieve their aim due to a variety of reasons including time constraints, appropriate people not being available, or a lack of understanding of what other disciplines require, and the handover process can degenerate into one of sending computer files on to the next discipline in the process flow. This paper focuses on the interface between the resource estimation and mine engineering disciplines, and outlines some of the common assumptions made when generating a resource model and the risks that engineers may be taking when elevating cutoff grades, optimizing schedules or generating forecasts. The case studies presented focus on openpit gold deposits, but the concepts should be applicable throughout the industry. A summary of key questions and recommendations is provided.

Jan 1, 2014

By J. A. Boyle

In the Frick District of U, So Steel Corporation, we have had more than 37 years of experience in the use of multiple-fan ventilation systems, in our coal mines. In our Colonial field, with a long belt installation, we have mined 85 million tons of coal with the use of the multiple fan system of ventilation. In our Palmer field, with the use of the same arrangement, we have mined 90 million tons of coal--a total of 175 million tons without one accident attributable to improper mine ventilation. The same system, fundamentally, has been installed in our expanding Robena operations and at its present stage of development we are using eight fans to ventilate this area. To date we have mined 55 million tons of coal with very encouraging results and again without any accidents attributable to ventilation.

Jan 1, 1961

By T. C. Rao

The quantum of coal fines below 6 mm in run-of-mine (ROM) coal has been increasing due to progressive mechanization of mining methods which has created a substantial incentive, worldwide, to develop suitable fine coal beneficiation techniques. The majority of the efforts have been directed toward reduction in ash/sulfur contents in clean coal. The beneficiation techniques may be broadly grouped as those based on specific gravity and surface property. The processes, which use heavy medium cyclone, water-only cyclone, concentrating tables, and spirals, belong to the former group while the latter group encompasses froth flotation, column flotation, oleo- flotation, and oil agglomeration. In almost all the gravity based techniques, it has been noted that a classification step prior to beneficiation is essential for effective treatment. In general, the effect of design and process variables on the performance of these units and also the quantification of the processes have been the main areas of research and development. In froth flotation, efforts throughout the world have been mainly to understand the effect of variables and to optimize the process. Quantification of the process has been attempted through kinetic studies and mathematical modeling. The efforts have led to the development of new reagents, machine designs, and flowsheets for a specified objective. The attempts so far with the column flotation and oleoflotation processes have indicated a great potential. Extensive R&D efforts are in progress to understand as well as to commercialize the processes. The efforts in the oil agglomeration process have been toward substantiating the inherent merits of the process by developing cheaper bridging liquids and technology to recover and reuse the oil to make the process commercially viable. Modeling of the process has also been attempted to predict the yield and size distribution of the agglomerates. This paper reviews and summarizes the recent developments in the science and technology of fine coal beneficiation processes. The current trends in R%D efforts for these processes are also highlighted.

Jan 1, 1987

By Trevor R. Ellis

In this paper a method is presented for estimating the specifications of sandstone-type uranium deposits which will be the minimum that can meet a company's economic requirements for investment. The method interpolates and extrapolates from available cost data for typical mines to provide the costs for a wide range of possible deposits. The range of deposits achieving the company's required discounted cash flow rate of return on investment at an estimated uranium oxide selling price is then calculated, thus giving the complete range of deposits which meet the minimum required specifications. Prospects are then evaluated by comparison with these minimum requirements.

Jan 1, 1979

In conjunction with steady increases in production levels, long-wall operators have applied greater quantities of ventilating air to control respirable dust and methane gas. As a result, air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high-velocities, especially during shield advance as dust falls from the shield canopy directly into theair stream. Laboratory tests to simulate dust liberation by shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH in a wind tunnel designed to study dust entrainment in high-velocity airstreams. Dust was introduced into the tunnel to determine dust concentration as it relates to entrainment, dilution, air velocity, and particle adhesion. Airborne dust samples were obtained by iso-kinetic sampling using BGI cyclones to quantify respirable dust concentration at the various air velocities. Laboratory tests were con-ducted at velocities ranging from 2.0 to 10.1 m/s (400 to 2000 fpm),and significant differences in airborne respirable dust levels were measured. This research is being conducted to provide fundamental information on the entrainment characteristics of respirable dust at high air velocities, which will subsequently lead to solutions for shield dust control. A discussion of the test procedures and results are presented.

Jan 1, 2004

By R. Hildebrandt, K. Cybulski, G. V. Goodman, Z. Dyduch, M. L. Harris, M. J. Sapko

Past research showed that bituminous coal dust remains dry and dispersible in the presence of moisture. Rock dust must disperse with the coal dust to effectively inert a propagating coal dust explosion. Non-treated rock dust readily absorbs moisture, limiting its dispersibility, while anti-caking treated rock dusts can remain dry. The National Institute for Occupational Safety and Health contracted the Central Mining Institute in Poland to conduct large-scale testing in their Experimental Mine Barbara to determine if a treated rock dust can be as effective as non-treated rock dust in attenuating or quenching coal dust explosions under the same experimental conditions. INTRODUCTION One of the goals of the National Institute for Occupational Safety and Health (NIOSH) is to conduct research to reduce the risk of mine disasters and provide workplace solutions to reduce the risks associated with accumulations of combustible and explosible materials; the most common form of which is the generation of coal dust during the mining process and its subsequent distribution downwind. Dispersible rock dust is a primary defense for preventing coal dust explosion propagation in underground coal mines, and its properties are defined in 30 CFR 75.2. “Pulverized limestone, dolomite, gypsum, anhydrite, shale, adobe, or other inert material, preferably light colored, 100 percent of which will pass through a sieve having 20 meshes per linear inch and 70 percent or more of which will pass through a sieve having 200 meshes per linear inch; the particles of which when wetted and dried will not cohere to form a cake which will not be dispersed into separate particles by a light blast of air; and which does not contain more than 5 percent combustible matter or more than a total of 4 percent free and combined silica (SiO2), or, where the Secretary finds that such silica concentrations are not available, which does not contain more than 5 percent of free and combined silica.” An earlier NIOSH investigation of rock dust revealed two significant concerns with the supply of rock dust to U.S. coal mines: 1) insufficient particles <200 mesh (75 μm) and 2) all rock dusts when wetted and dried formed cakes and were not easily dispersed with a light blast of air (1). Past research by the U.S. Bureau of Mines and others showed that bituminous coal dust remains dry and dispersible in the presence of moisture (2). Rock dust must also be dispersible in concert with the coal dust to effectively inert a propagating coal dust explosion (3, 4, 5, 6). Non-treated rock dust, however, readily absorbs moisture, limiting its dispersibility, while a rock dust treated with long-chain fatty acids (such as stearic acid) can remain dry and dispersible. Stearin-treated rock dust has been used in British coal mines (7) and is commonly used in Polish coal mines.

Jan 1, 2019

By A. M. Gaudin

In the first place, let me thank you for inviting me to appear before you today to speak to you on "Mineral Industry Problems - Present and Future". It is a distinguished honor for me to have this opportunity, and I am highly appreciative of this distinction. The beautiful surroundings of Gatlinburg and the pleasantness of a summer occasion are a wonderful tonic for all of us, yet they should not blind us to the seriousness of our Industry&apos;s problems No doubt, because of my past appearances before members of the Society of Mining Engineers, at which I discussed wholly scientific topics, or research in the Applied Sciences, you may be expecting me to revert to these subjects. But I intend to venture in a field that is new to me, yet old to all of us, the field of Economics.

Jan 1, 1962

By T. P. Lim, A. J. Vivyurka, N. K. Davé

Chemical and radioisotope stratification studies were carried out in an abandoned uranium tailings pile at Elliot Lake, Ontario, Canada. The tailings, with an average thickness of 7 m over an area of 16 hectares, were deposited approximately 20 years ago on a layer of black peaty material which overlays deposits of permeable glaciofluvial sands. Geohydro-chemical investigations of this tailings area have been ongoing since 1978. The radioisotope profile study was conducted on three adjacent sites. Solid core samples, collected with a split spoon sampler at various depths, were analyzed for various chemical and radioisotope constituents. The results indicated by 2 distinct zones of stratification; an upper zone, where the constituents were uniformly distributed, and a lower zone, near the peat-tailing interface, which showed increasing concentration with depth. Within the peat layer, the concentration decreased rapidly with no significant levels of contaminant penetration below the peat layers observed, though the samples were limited. The pH profile showed that the top 5 m of the tailings have been oxidized, the average soil pH in this zone was 3.4 compared to 5 .8 underneath it. The groundwater hydrology of the system was observed to be complex showing downward and lateral flow in the dry season and lateral and upward flow during the spring and periods of heavy rainfall. The results are discussed in terms of a model based on the combined segregation and settling process of the tailings fine fraction, and the geohydro-chemical interaction of the solid and liquid phases.

Jan 1, 1981

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer studies as well as for studies conducted in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources has been previously demonstrated in underground mines, but this new work details the testing of multiple, distinct tracer compounds compatible with passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed: (1) PMCH, (2) perfluoroethylcyclohexane (PECH) and perfluoromethylcyclopentane (PMCP). The release rates of these tracers were examined over a 180-day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in characterizing ventilation circuits, flow through gob and leakage. IntroductionThe use of tracer gases for ventilation applications is an established practice, with various past research projects conducted using sulfur hexafluoride (SF6). Tracer gas techniques have been applied to assess flow rates, dilutions rates and auxiliary ventilation system efficiencies with quick, reliable and accurate results (Suglo and Frimpong, 2002). Perfluorocarbon tracer (PFT) compounds are a new introduction to ventilation and air modeling applications in terms of ventilation flow characterization (Watson et al., 2007).PFTs are liquids that are characterized by low background presence in air, low reactivity, high detectability and low toxicity. A design was proposed, called a permeation plug release vessel (PPRV), to convert PFTs from a liquid to a gas and then release the gaseous tracer in a controlled manner. The initial concept was originally introduced by Brookhaven National Laboratory and refined later to become the PPRV. The PPRV functions by allowing the volatile PFT liquid to become a vapor in a controlled manner. The vapor diffuses through a permeable silicone stopper at a predictable rate proportional to temperature (Zhang and Cloud, 2006)."

Jan 2, 2018

By G. E. McCormack

The Development of Water Gel Explosives Water gels are the most recent development in the evolution of commercial explosives. They are replacing dynamite, having proven themselves to be excellent alternatives to this standard explosive. Water gels have steadily displaced dynamite over the past two decades. In 1959, they accounted for only 1 percent of the market they share with dynamite. By 1965, the share taken by water gels had grown to 21 percent. In 1970, it was more than 40 percent, and today it is nearly 70 percent. Black powder, the first widely used explosive, revolutionized mining and quarrying in its day. However, when nitroglycerin dynamite became available about a century ago, it rapidly displaced black powder because it provided greater energy for a given weight, much higher velocity for better rock shattering performance, and water resistance for easy use in wet conditions. During the past 50 years, ammonium nitrate has played a dramatically increasing role in explosives. First, it was used as an ingredient in dynamite, and then as the main component in nitrocarbonitrate blasting agents. About a quarter of a century ago, it began to find use in a simple and inexpensive mixture with fuel oil that has revolutionized the explosives industry and today fills about 80 percent of the requirements for explosives in the U.S., and certainly the bulk of blasting requirements worldwide. Water gels and dynamites share the remaining 20 percent. Water gel explosives based on ammonium nitrate have also been developed during the past quarter century. These explosives contain

Jan 1, 1979

By M. A. S. Martins, H. Medeiros, B. Y. B. Dos Santos

This paper contains the geometallurgical studies, performed for Mineração Rio do Norte bauxites, applied to a selected area belonging to Plateau Saracá III, referring to an exploitation period of one year and three months, approximately. It is worth mentioning that Mineração Rio do Norte has the biggest bauxite operation in Brazil producing 8,500,000 tons of concentrate per year. The studies included wide investigations directed to the final objective of establishing a precise mining and production planning, based on the different behavior of the distinct bauxite ores, when submitted to industrial processes. Geometallurgy can be defined as the study of the regionalization (space distribution) of the metallurgical variables of a mineral deposit. This study involves and integrates all process engineering, geology, geostatistics and mining planning, among others. The development and application of the geometallugical studies to Mineração Rio do Norte were motivated by several reasons and necessities, among them: 1. Improving the forecast of the amount of concentrate (metallurgical mass yield) produced; 2. Improving the equipment operational efficiency, providing a more homogeneous feed; 3. Conducting a more precise material balance that permits a better daily, monthly and yearly production control; 4. Improving the forecasts for the final products generated by each ore type; 5. Obtaining better knowledge of the behavior of several ore types, submitted to the different process unit operations; 6. Promoting adequate ore blending, producing an homogeneous feed during mining operation.

Jan 1, 1998

By Bruce C. Trent

The need for effectively evaluating the potential for surface subsidence due to under- ground mining has been widely documented. As the emphasis within the coal mining industry changes to reflect the increasing demand of this resource, the potential for damage due to differential surface subsidence will certainly become more acute. The present state-of-the-art of predicting ground motion due to underground excavations is, at best, primitive when one considers the immense complexity of possible geological inter- actions. For the most part predictions have been limited to empirical evaluations based upon earlier case histories. While the tools of the subsidence engineer are limited, they are important and serve to provide reasonable bounds for possible ground motion. As underground mining becomes more extensive, however, there will be many instances where excessive subsidence will be most undesirable and yet there may be few, if any, case histories similar to the operation in question.

Jan 1, 1982

By L. Adler

A systematic, balanced and inclusive formulation of the vast input data for mine design is presented. Since the quality of this statement severely influences subsquent design it is extremely important to senior mining engineers and the profession-at-large. If unfocussed, chaos can result along with serious ommisions. The basic categories, each a traditional one are: 1) Natural Conditions (geology and geography), 2) Company Capabilities (monetary and managerial), 3) Public Domain (regulations, contracts, good will, etc.) and 4) State of Art (mining engineering professionalism). To further reduce the data additional organizing principles were used: the distinctions of mining (vs. civil) engineering, proceeding from the general to particular, the basic engineering dimensions, and separating dependent from independent variables. The results are a unique and unified corpus, which anticipates the mine design procedure.

Jan 1, 1987

By Frank E. McCall, Michael A. Trevits, Fred Garcia

The U.S. Bureau of Mines investigated the influence of atmospheric pressure changes on methane gas migration through mine seals at a mine site located in the Pittsburgh Coalbed. The mine gained access to a coal reserve through part of an abandoned mine and constructed nine seals to isolate the extensive old workings from the active mine area. Underground problems were experienced when atmospheric pressure fell, causing methane gas to migrate around the seals and into the active workings. During mining operations, methane gas levels exceeded legal limits and coal production was halted until the ventilation system could be improved. When mining resumed with increased air flow, methane gas concentrations occasionally exceeded the legal limits and production had to be halted until the methane level fell within the mandated limit. To assist the ventilation system, a pressure relief borehole located in the abandoned workings near the mine seals was proposed. Preliminary estimates by a gob gas simulator (computer model) suggested that a 0.76 m (2.5 ft) diameter pressure relief borehole with an exhaust fan would be necessary to remove enough methane from the abandoned area so that the ventilation system could dilute the gas in the active workings. However, by monitoring methane gas emissions and seal pressure, during periods of low atmospheric pressure, the amount of methane gas that migrated into the active mine workings was calculated. Researchers then determined that a relief borehole, 20.3 cm (8-in) with an exhaust fan could remove at least twice the maximum measured volume of migrating methane gas. Because gas concentrations in the abandoned workings could potentially reach explosive limits, it was proposed that the mine eliminate the exhaust fan. Installation of the recommended borehole and enlarging two other ventilation boreholes located in the abandoned area reduced methane gas leakage through the seals by at least 63%.

Jan 1, 1995

By J. DuCarme, A. Smith, M. Reyes

"A magnetic proximity detection system is mounted on a mobile mining machine to prevent underground workers from being pinned or struck by machine motion. The system generates magnetic fields around the machine to determine safe working distances. The minerworn component measures the magnetic field in order to approximate location. Large masses of steel, such as those from mining equipment, can alter the magnetic field distribution. This affects the locational accuracy of the system, thus adversely impacting worker safety. To examine this problem, U.S. National Institute for Occupational Safety and Health researchers developed a method and test system to study the influence of a steel mass on the magnetic field distribution. The results show that a steel plate can strengthen the magnetic field perpendicular to the generator by up to 40 percent. Furthermore, they show that the degree of the influence on the field distribution is a function of distance. The results from this study can be used to further develop and improve the performance and reliability of electromagnetic proximity detection systems used in underground mining applications.IntroductionOn average, 250 miners are injured every year, and 43 miners were reported to be killed by striking or pinning accidents involving continuous mining machines in the United States between 1984 and 2015, according to the U.S. Mine Safety and Health Administration (MSHA, 2015). Continuous mining machines are large mobile machines used to mechanically cut coal in underground mines. These machines weigh approximately 60 t (132,000 lb) each. Although modern continuous mining machines can be remotely controlled, operators still need to be close to the machine primarily because of the low visibility and wide blind spots of the underground working environment.The MSHA promulgated a final regulation in 2015 that requires the use of proximity detection systems on all continuous mining machines except fullface machines. MSHA has approved five such systems to be intrinsically safe for use in underground coal mines: (1) Strata Worldwide’s HazardAvert System, (2) Frederick Mining’s Model 200 HazardAvert Detection System, (3) Nautilus International’s Coal-Buddy System, (4) Matrix Design Group’s M3- 1000/Joy Global SmartZone Gen 1 and (5) Matrix Design Group’s IntelliZone/ Joy Global SmartZone Gen 2."

Jan 6, 2018

By C. Roos

Tradicionalmente en la industria minera, el flujo principal del proceso funcional para la evaluación de recursos y reservas procede de geólogos que elaboran el modelo geológico, de allí a los geólogos que hacen la estimación de los recursos (los modeladores) quienes estiman los grados, y a los ingenieros de mina que desarrollan el diseño de la mina y su calendario. La interfaz entre estas tres disciplinas no está siempre exenta de baches. Las presunciones hechas durante una etapa del proceso no siempre son comunicadas a los demás, a pesar que la mayoría de las empresas mineras tienen procedimientos y protocolos establecidos para promover la comunicación a lo largo de las distintas disciplinas. Estos procedimientos no siempre logran su propósito debido a una variedad de razones que incluyen restricciones de tiempo, no tener disponible a las personas apropiadas, o a una falta de entendimiento de lo que las otras disciplinas requieren, y el proceso de traspaso puede degenerar en el envío de archivos a la siguiente disciplina en el flujo de proceso. Este artículo se ocupa de la interfaz entre la estimación del recurso y las disciplinas de la ingeniería de minas y el esquema de algunas de las presunciones comunes hechas al generar un modelo del recurso y los riesgos que los ingenieros podrían correr al elevar los grados de corte, optimizar calendarios o realizar predicciones. Los casos de estudio presentados se centran en depósitos de oro a cielo abierto, pero los conceptos deben ser aplicables a toda la industria. Aquí también proveemos un resumen de preguntas clave y recomendaciones.

Jan 1, 2014