Search Documents

By F. B. Brost

In 1976, a decision was made by Anamax Mining Company to install an unusual conveying system to transport ore 10.3 km (6.4 mi) from the new Eisenhower Mine to the Twin Buttes concentrator. The system, supplied by Cable Belt Limited of the United Kingdom, represents a radical departure from conventional belt conveyors. The driving tension is applied through two endless wire ropes driven by a single 2 240 kw (3 000 HP) drive while the belt acts only as the ore carrying medium. Full production was begun in January, 1979. Start-up problems hampered production for several months but were resolved by a joint Anamax-Cable Belt effort. The system has been operating at design capacity for 4-1/2 years, and has proven itself as a reliable, low cost ore transportation system.

Jan 1, 1984

By Otis M. Clarke

Domestic bauxite used in aluminum production comes from Arkansas where syenite was lateritized forming bauxite. Part of the residual bauxite and kaolinized syenite were eroded, deposited downdip, lateritized with bauxite formed in place, and covered by sediments. The unconsolidated overburden causes problems in mining. Bauxite for refractories and chemicals comes from Alabama and Georgia. Sediments were deposited in karst lakes and were lateritized forming bauxite and kaolin. Ferruginous bauxite in Washington, Oregon and Hawaii, derived from weathered basalt, can be used in aluminum production.

Jan 1, 1984

By M. Ghiani

Biohydrometallurgy originated, some forty years ago, from an environmental problem, namely the serious pollution of the Ohio river by acid drainage water coming from neighboring subbituminous coal mines. Studies aimed at elucidating the cause of the intensive oxidation of the iron sulfide (pyrite) inclusions of those coals, led to the discovery of a bacterium, Thiobacillus ferrooxidans (Temple and Colmer, 1951), capable of acting as a catalyzer, accelerating the otherwise very slow chemical oxidation of iron sulfide to rates many orders of magnitude higher. However, it is now recognized that the biotechnology of microbial mining dates back to 1963, when the ability of this bacterium to solubilize copper from sulfide ores was ascertained (Razzell and Trussell, 1963). Much research has been carried out on biohydrometallurgy over these last 25 years and is still being actively conducted all over the world. The interdisciplinary nature of this young branch of science and technology is reflected by the variety of experts involved: microbiologists, mining engineers, hydrometallurgists, physico-chemists, mineralogists, solid-state physicists and biochemists. This intensive research effort has provided a solid background on the fundamentals of this technology, although many important issues have still to be solved, amongst which the enzymatic mechanisms controlling biocatalysis of mineral sulfides dissolution, the influence of bulk- and surface solid-state physics of metal sulfides on dissolution mechanisms, the interaction of the various strains composing natural microbial floras. Their elucidation should permit the rationalization of biohydrometallurgical techniques and the optimization of commercial processes. Biohydrometallurgy has already achieved satisfactory results: copper recovery from submarginal copper sulfide run-of-mine ores (i.e. assaying less than 0.3% Cu) by in-situ, dump and/or heap leaching is successfully practised in many countries and uranium recovery through bioleaching is competitive with other leaching processes.

Jan 1, 1987

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau ofMines (USBM) have given a significant effort over the past four decades in researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers performing manual bagging and palletizing of 50- to 100-pound bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper will provide an overview of available dust control technologies for bagging operations and present the findings of a recent case study that was conducted at four different industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation will also be performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

Apr 3, 2020

By R. L. Wolfrom, R. Hogg, S. Chander

A gravimetric method for measuring rates of capillary rise in powders was explored. Methods to improve reproducibility and consistency of the results were investigated. In particular, the effects of particle size and packing uniformity were addressed. Studies of the wetting behavior of both spherical glass beads and irregularly shaped synthetic graphite particles by various organic liquids were carried out. Standardized procedures for bed preparation will be described. The applicability of the Washburn equation for surface energy evaluation in such systems will be discussed. Key words: Wettability, Powders, Capillary rise, Surface chemistry

Jan 1, 2003

By Walter C. Labys

This paper reports on recent modeling efforts to analyze the eastern U.S. steam coal market with a cross-sectional econometric as well as a quadratic programming approach. The background to coal modeling is examined first. The particular aspect of the steam coal market to be modeled are then presented and the corresponding coal model described. Both empirical results and rigorous mathematic pertubation analysis are presented. Conclusions are then drawn regarding potential modeling applications in the policy area.

Jan 1, 1979

By Thomas P. Meloy

Comminution is an old art. Unfortunately the analysis of the unit operations has been handicapped by the lack of both theoretical and experimental information. Two types of infor¬mation are needed, one an understanding of what happens when a particle breaks in a brittle manner; and two, an understanding of what happens when the daughter fragments pass through the mill. This paper is concerned with the former, the catastrophic fracture of a brittle solid. Recently, successful theoretical attacks on the frac¬ture of brittle solids have yielded significant-results. New experimental techniques are yielding insight into the physical phenomenon occurring during brittle fracture. Many of the re¬doubtable shiboliths of the last century are either being laid to rest or verified.

Jan 1, 1965

By J. P. Golightly

The nickeliferous laterites of Soroako are described in their setting in the huge Cretaceous ultramafic complexes of central Sulawesi, Indonesia. The ore bodies occur on spurs, ridges and hill flanks beneath remnants of extensive erosional surfaces. Weathering pro- files that have developed on unserpentinized harzburgite and on strongly serpentinized lherzolites show distinctive laterite structures, mineralogy and chemistry. The former are unique to the Soroako area and permit an unusual degree of upgrading by rejection of unserpentinized peridotite boulders. A mass balance calculated for a selection of profiles indicates that in situ leaching of a column of peridotite 20-50 meters thick has taken place with only minor lateral migration of nickel in solution.

Jan 1, 1979

By Ted H. Eyde

Improving the mineral industry's tarnished image describes in a nut- shell the reason why the Speakers Bureau of the Tucson Subsection of the AIME was formed. Let's go back in time about 3 years to the fall of 1971. Literally thousands of bills detrimental to the mineral industry were being introduced into Congress and State Legislatures. Unfortunately, many were being passed and signed into law. Clean air and water, zero pollution, preserve the environment, ecology, biodegradeable, wilderness were the words that the self- styled ecologists and environmentalists were preaching. The mineral industry either sat mute or in place of acting, reacted in a way certain to attract a maximum amount of bad publicity with a minimum amount of rhetoric. A mining company president, for example, commenting on the primary air standards in Arizona was reported by the press as having said, "we'll shut all the smelters down and put thousands of Arizonans out of work if we have to meet the Arizona standards." Or another defending a poorly planned highly visible open pit nonmetallics operation, "we'll take the whole mountain down if we want to, and nobody can stop us" and still another manager of Operations, "the bottom line is all that counts, to hell with all of this environmental nonsense."

Jan 1, 1975

By Donald W. Gentry

This article introduces mine planning as a complex process based on the quantitative and qualitative assessment of a myriad of independent and inter-or co- dependent variables. The interdependent variables of particular interest in this paper are those associated with mine planning activities that impact metallurgical processing plant performance and costs. These variables are identified and examples are provided to substantiate the argument that the magnitude and sensitivity of these variables must be formally assessed and analyzed to determine their potential impact on overall economics.

Jan 1, 1991

By Kurt Egger, Emily A. Baker

Rehabilitation work at the Cameron Run Tunnels entailed the restoration of seven heavily deformed, approximately 69 m long, steel liner plate supported culverts through a CSX Railroad embankment near Alexandria, Virginia. A custom fabricated expander, equipped with four 200-ton hydraulic jacks on two expansion arms was used to push back the liner plates encroaching into the proposed tunnel profile and install the steel set support. In a second phase the tunnels were then lined with 16 cm of fiber reinforced shotcrete. Geotechnical instruments both in the tunnels and on the railroad embankment were used to monitor the effects of the rehabilitation work on the two CSX Railroad tracks above the tunnels. Freight and passenger trains were required to run uninterrupted and at maximum speeds throughout construction.

Jan 1, 2003

By A. S. Malicsi, Vathsala Rajagopal, I. Iwasaki

Corrosion and abrasion properties of a series of chromium-containing, cast-iron balls, with Cr contents ranging from 0% to 29%, were evaluated and compared with austenitic stainless-steel and mild-steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite, with either 5% pyrrhotite or 5% chalcopyrite, under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynantic polarization curves under abrasion. Flotation recoveries were determined on a 95% quartzite + 5% pyrrhotite sample ground with various cast-iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with flotation results and with corrosive wear data obtained from marked ball wear tests.

Jan 1, 1993

By Petr Salak, Adrian St. John, Angelos Gakis

"INTRODUCTIONCrossrail will provide London and the South East of England with a world class, high-capacity railway to ease congestion on London’s public transport system and enable better access between business, residential and entertainment districts. At the heart of this £14.8bn scheme lies Farringdon Station, which will form a major interchange between Crossrail, Thameslink and London Underground. The £400m Farringdon Crossrail station was awarded to a joint venture of BAM Ferrovial Kier (BFK) in 2011, and comprises two ticket halls, two platform tunnels and a multitude of connecting tunnels all constructed using open face sprayed concrete linings (SCL). BFK appointed Dr. Sauer & Partners (DSP) as their specialist SCL designer. As the main contractor for both C300/C410, the Western Running Tunnels and Station Caverns, and also for C435 Farringdon Station, BFK were in a unique position to develop strategies to reduce cost, time and risk for the Client. One such innovation involved the continuation of the TBM drives for the running tunnels right through the length of the new Farringdon platform caverns. This created large diameter precast concrete pilot tunnels for the subsequent platform enlargement using SCL. The benefits of such an approach are described in detail by St.John et al 2015. BFK also introduced another alternative strategy to reduce cost, time and risk, by proposing to abandon the TBMs in the ground (“Turn & Bury”) permanently rather than recovering them through the ticket hall shafts. This de-risked the programme, enabling critical ticket hall construction to proceed unhindered. However, one consequence of this revised strategy was an area of increased underground congestion, with two SCL tunnels (RTE2 and ES2) and a bored tunnel (complete with abandoned TBM) in close proximity to a ticket hall excavation (see Figure 1) and a sensitive, listed railway structure. Faced with this complex geometry, and combined with challenging geotechnical conditions (Gakis et al 2015), the team chose to install enhanced monitoring to study the behavior of tunnel RTE2 and provide additional assurance that the tunnels were performing as predicted. Applying advanced 3D numerical modelling and taking into account the residual tensile strength of the SCL helped avoid unnecessary reinforcement installation in primary lining and/or early installation of a secondary lining in RTE2 prior to ES2 construction."

Jan 1, 2016

By Jim Gebhardt

Douglas W. Fuerstenau (DWF) grew up on a farm and in several small communities in rural South Dakota during the depression years, where he learned the value of hard work. Working hard can produce results but being clever and hardworking will give you a bright future. In his later school years, Fuerstenau’s family moved to Rapid City where his intellectual curiosity and capacity helped him graduate with a B.S. in Metallurgical Engineering from the South Dakota School of Mines and Technology in 1949. His technical interests led to graduate studies and completion of a master’s degree from the Montana School of Mines in 1950 and Sc.D. degree from the Massachusetts Institute of Technology (MIT) in 1953.

By J. Brinen, D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By M. Manrique, E. E. Vidal, I. Accorsi, P. R. Taylor

Various pyrometallurgical methods for treating ilmenite and zircon concentrates are reviewed. Laboratory experiments using a thermal plasma reactor were performed to evaluate the conversions of ilmenite to TiC or TiC-Fe and zircon to ZrC or ZrC-SiC. Results are examined and possible processing routes are identified.

Jan 1, 1999

By Bernard J. Scheiner, R. J. Wesely, Cy E. Jordan, A. D. Zunkel, Gary M. Wilemon

The U.S. Bureau of Mines has investigated leaching of off-grade western United States phosphate deposits using sulfuric acid (H2SO4) in the presence of methanol. A combination of ore grinding followed by sulfuric acid in methanol leaching extracted over 80 pct of the phosphate. This leaching technique significantly limited the dissolution of iron, aluminum, and magnesium impurities and produced a phosphoric acid that was well within the desired limits for these impurities. The dissolution rate of phosphate rock in the sulfuric acid methanol system was significantly slower than the conventional aqueous sulfuric acid dissolution. Initially dissolution of the phosphate particle was controlled by the amount of surface area available to the sulfuric acid reactant. After about an hour of leaching, phosphate dissolution was slowed almost to a stop, limited by the rate of ion diffusion through the calcium sulfate barrier layer surrounding the unreacted phosphate particle. Consequently, the ore was ground below 38-pm to increase the particle surface area available and improve the overall dissolution kinetics and extraction. In addition, the sulfuric acid was slowly metered into the reactor to prevent any excess heat from the mixing of acid with the methanol from simulating the formation of methyl sulfates. The formation of methyl sulfate ultimately lowered the overall phosphate extraction by exhausting the supply of available sulfate ions for the dissolution reaction. Subsequent evaporation of the methanol from the product acid decomposed the methyl sulfates leaving undesirable sulfate ions in the product acid. Slow acid addition to the reactor provided high phosphate extraction and limited the amount of sulfate in the final product acid.

Jan 1, 1993

By Y. Ye, J. D. Miller

Certain bituminous coals are known to contain appreciable quantities of natural fossil or subfossil resin. Such resinous coals are found in the western US, particularly the Wasatch Plateau coalfield of UT. Some of the seams in this field contain an average of 5% resin. This fossil resin has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction. The purified resins are of commercial importance in the adhesive, coating, rubber. and ink industries, etc. An improved flotation technique has been developed which involves ozone conditioning to selectively float resin from high-volatile bituminous coal. With this flotation process, a concentrate product which contains 95%

Jan 1, 1990

By Arun Patel, Diane Hirsch, Pamela Moran

The Metropolitan Washington Airports Authority (Authority) has undertaken a tremendous expansion of Washington Dulles International Airport in Fairfax, Virginia, including upgrading passenger transportation between concourses. The first stage of this expansion envisioned a shallow cut-and-cover pedestrian tunnel between the Main Terminal and Concourse B with associated vertical circulation structures. At the beginning of the design contract, the Authority’s consulting team of Earth Tech, formerly Kaiser Engineers, and the Dr. G. Sauer Corporation compared the cost and disruption of constructing the tunnel as a cut-and-cover structure to mining the tunnel using the New Austrian Tunneling Method (NATM). Upon review, the Authority endorsed the latter method.

Jan 1, 2003

By R. Pazhianur

Many investigators conducted surface force measurements between hydrophobic surfaces in water, and observed attractive force that was substantially stronger than the van der Waals attractive force. The excess force was appropriately referred to as “hydrophobic force”, for which many different theories have been put forth by numerous investigators. In an earlier publication (Yoon and Ravishankar, 1996), it was suggested that the hydrophobic force maybe due to the interaction between the large dipoles created by the surfactants adsorbing on solid surfaces in patches (or domains). In the present work, a mathematical model has been developed to further elaborate the theory.

Jan 1, 2003