Search Documents

By D. N. Madge

A description will be given of an approach to plant process automation based on the strategy of first developing an information system followed by later development of process models. The advantages of this approach over the unit process control will be outlined. Some insight will be given into the risks associated with this method. These risks can be shown to be primarily economic.' Some reference will be made to two Cominco installations in the interests of illustrating the generality of the information systems approach.

Jan 1, 1972

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By K. Häge

"Die Nachhaltigkeit der Braunkohlengewinnung in der öffentlichen Wahrnehmung wird nur weiter erfolgreich kommuniziert werden können, wenn durch konkretes Handeln glaubhaft gezeigt wird, dass die offenen Fragen fair und solide beantwortet werden. Dazu gehören insbesondere die neue innovative technische Lösung sowie das sensible Interessenmanagement. Die Braunkohlenindustrie hat gelernt, dass Offenheit und nicht zuletzt das beständige Bemühen um den Meinungsaustausch mit ihrem Umfeld wichtige Elemente sind. Der in Jahrzehnten erworbene Schatz an Glaubwürdig-keit ist eine Basis, auf der die Braunkohlenindustrie ihre Zukunft gestalten kann. Darüber hinaus sind politische Rahmenvorgaben erforderlich. Das öffentliche Interesse an einer sicheren und preiswerten Energieversorgung unter Einschluss der Braunkohle ist unverzichtbar. In diesem Kon-text kann dann die Braunkohle die an sie gerichteten Fragen der Ökonomie, der Ökologie und der Sozialverträglichkeit auch mit Hilfe von Indikatoren beantworten.ABSTRACTThe discussion of the sustainability of lignite mining can only be continued successfully if the indus-try acts in a practical manner and demonstrates trustworthiness by responding fairly and reliably to open questions. This includes new and innovative technical solutions as well as the sensitive management of interests. The lignite industry has learned that openness and the constant effort to exchange viewpoints within their environment are all essential elements. The credibility that has been gained over the decades is the foundation on which the lignite industry can build its future. Beyond that a framework of political guidelines is necessary. Public interest in a secure and inex-pensive energy supply that also includes lignite is indispensable. In this context, the lignite industry will then be able to answer the questions which are directed at them and concern the economy, ecology, and social tolerability also by indicators."

Jan 1, 2005

By Weijie Wei, Jinwang Zhang, Jiachen Wang, Yang Li

"Longwall top-coal caving (LTCC) mining technique is one of the important methods for underground thick seam extraction in China. The coal seam in LTCC panel is divided into two parts: bottom-coal and top-coal. The bottom-coal is mined by conventional longwall method while the top-coal is mined by caving method. The top-coal caving process in LTCC and block caving process in metal mine are both gravity flow of loose ore/coal blocks. However, the presence of caving shield in LTCC makes the characteristics of drawing body shape in the two caving processes differ a lot. This paper discusses the influence of caving shields on the characteristics of drawing body shapes in light of recent studies of the top-coal drawing process. The theoretical model for describing the drawing body shape in LTCC is proposed both along the seam strike and seam inclination. Then, the experimental data are used to validate the correctness of the theoretical model. Furthermore, two examples of how the theoretical findings assist LTCC mining are given and discussed.INTRODUCTIONLongwall top-coal caving (LTCC) mining technique and large-cutting-height mining technique have been widely used for extracting thick coal seams in China. About 0.6–0.7 billion metric tons of coal come from longwall top-coal caving panels every year. The maximum annual production is 15 million metric tons per panel _The mining method employed in such panel is a combination of top-coal caving mining technique and large-cutting-height mining technique, which is suitable for seam height between 12–20 m, as shown in Figure 1. Apart from China, LTCC has also been employed in some coal mines in Australia and Vietnam (Le et al., 2017).The coal seam in a LTCC panel is divided into two parts: bottom coal and top coal. The bottom-coal is mined by the conventional longwall method, while the top coal is mined by the caving method. The top-coal caving process in LTCC and block caving process in metal mines are both gravity flows of loose coal/ore blocks, as shown in Figure 2. However, the presence of caving shields in LTCC causes the characteristics of the drawing body shapes in the two caving processes to differ significantly.There are two main differences between the blocking method and the top-coal caving method:"

Jan 1, 2019

By Marshall D. Himes, Erich U. Petersen

The Sheep Creek deposit near White Sulfur Springs, Montana, is a middle Proterozoic stratabound and strataform sediment- hosted massive sulfide containing 4.5 million tonnes (5.0 million tons) averaging 2.5% copper, and 0.1% cobalt in the upper sulfide zone (USZ) and 1.8 million tonnes (2.0 million tons) averaging 6% copper in the lower sulfide zone (LSZ). Mineralization is hosted in lower Newland shales and debris flow conglomerates in the graben controlled Helena Embayment of the Belt Basin. USZ mineralization is characteristically high in Cu, Co, Ni, Ba, As, Pb, and Ag. Mineralogically it consists of barite, pyrite, chalcopyrite, and tennantite with minor amounts of marcasite and various cobalt minerals. By contrast, the LSZ is higher in Cu, Ni, and Au and lower in Co, As, Pb, and Ag. Mineralogy of the LSZ consists of dolomite, pyrite, and chalcopyrite. In both zones significant amounts of cobalt, nickel, arsenic and copper are incorporated in pyrite rims. Tennantite controls the abundance of numerous trace elements in the ores. Fluid incluison data from hydrothermal USZ barite suggests that mineralization took place at temperatures in excess of 250°C, under relatively oxidizing conditions (f02 = 10-32+1) from moderately saline (1.1-3.5m), metal rich brines. The absence of barite in the LSZ suggests mineralization under more reduced conditions (f02 = 10.38+2). Mineralization was initiated following basin subsidence in excess of 400m. Contemporaneous with movement along a growth fault(s) was upward migration of hot metal-bearing fluids which permeated the loosely consolidated sediments and may have vented on the sea floor. The differences in the two zones may be explained by the effects of variations in local basin morphology and solution chemistry.

Jan 1, 1990

By Alan C. Richter

Introduction The East-West Gateway Coordinating Council is an organization of local governments formed in 1965 to identify regional problems and to formulate policies, plans and programs to resolve them. The major goal of the Gateway Council is to improve the quality of life for the citizens of the St. Louis Region. While East-West Gateway Coordinating Council is the organization I represent and it only deals with the St. Louis Metropolitan Area, you will find one or more similar organizations in each of our nation's urbanized areas. As a result, for illustrative purposes, I will use my organization to portray what is happening nationwide. For example, in order to eliminate duplication, the Council reviews local applications for approximately 100 federally funded programs in such areas as highways, mass transit, parks, water treatment, and sewers before they can be sent to the appropriate funding agency. The Council's varied functions place it in a unique position of receiving more and more responsibility for developing strategies of implementation of various environmental regulations. This is due to the fact that environmental control is a relatively new field and we, as a country, are relatively inexperienced. The resulting regulations and guidelines will depend, to a great extent, on what the general public is willing to accept in terms of controls and what price they are willing to pay in terms of taxes and increased costs. Land Use: Growth vs No Growth This is perhaps the most encompassing environmental issue. We, as a nation, are beginning to realize that land is a limited natural resource and that the way we choose to use 'this resource affects many other aspects of our lives--whether we can catch edible fish in the Mississippi, how much we pay for sewer services, if we can swim in a

Jan 1, 1977

By Samer Sadek, Phoebe Cheng, Changmo Kwon, Myat Ohn

BART Facilities Standards (BFS) Structural Criteria is a living document that governs planning, design, and construction of all BART projects. Since its development, the document undergoes incremental changes and updates to reflect policy changes, changes in local, State, or national design codes and guidelines, advancements in engineering and technology, or based on the performance of past built infrastructure. In 2020, the BFS-Structural Criteria underwent a comprehensive update and was released with BFS version 3.2. This paper summarizes the updates to the Tunnels and Underground Structures Section of the Structural Criteria, and provides insights to the basis and logic of the requirements.

Dec 1, 2022

By V. L. Brant

The estimated total energy demand for the U. S. is 60 quadrillion BTU for 1970 and is expected to more than double by the year 2000. Today the energy crunch is here. It is evidenced by brownouts to conserve electrical energy, and the shortage of gas and oil. Many such headlines, including suggestions for energy rationing, are in the news today. Paradoxically we have an abun¬dant source of energy in the form of coal. Energy consumers, however, are geared to use fuel in other forms. It is the intent of this presentation to discuss processes under development for conversion of the energy contained in these vast coal reserves to more usable forms. Coal conversion to synthetic fuels should be of particular interest to those engaged in mining. Coal consumption in a single conversion plant is expected to range from 10,000 to 40,000 tons per day. Plants will be located at the mine mouth and will operate continuously 24 hours per day, seven days per week. Further, many such plants will be needed., For example, looking at natural gas only, the supply/demand gap is estimated to reach 13 trillion cubic feet per year by 1985. Assuming that gas from coal conversion were to fill only 101, of this gap, 15 plants producing 250 MMSCFD would be required. These plants would consume about 90 million T/Y of coal or 135 million T/Y of lignite. It will indeed be a challenge to mine, suitably prepare, and transport coal at these projected volumes without interruption. Many ideas have been conceived for better utilization of coal and these are in various stages of development. Those supported by public money are covered by the Annual Report of the Office of Coal Research (OCR), Department of Interior. The two processes to be discussed, the Consolidation Coal Company's (Consol) C02 Acceptor Process (1)(2)(3) and The Pittsburg and Midway Coal Mining Company's (PAMCO) Solvent Refined Coal Process (4)(5) are both sponsored by OCR.

Jan 1, 1970

By Dennis S. Kostick

Soda ash is produced in over 39 countries by the Solvay ammonia-soda process or by mining natural sodium carbonate deposits. The total production of soda ash in 1980 is estimated at slightly over 29 million metric tons. Synthetic production accounted for over 75% of this amount with the balance of production originating from natural sources (either trona or sodium carbonate-rich brines) found primarily in the United States, Mexico, Kenya, and Chad.

Jan 1, 1981

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By R. Fields

Nevada is primarily known today for its nation-leading production of gold and silver. However, industrial mineral production continues to play an important role in providing construction materials to help make the state the fastest growing in the United States. Aggregate production in Nevada was about 20 million tons in 1991. Most of that was used in construction in the fast-growing Las Vegas area. The state leads the nation in the production of barite and mined magnesite and has significant production of lithium carbonate, diatomite and gypsum. Other industrial minerals produced in the state include specialty clays, silica, lime and dolomite and relatively small production in salt, perlite and dimension stone. Industrial minerals operations are subject to state and federal permitting requirements, especially in the areas of air and water quality and mined land reclamation. As in all segments of the mineral producing industries throughout the nation, the amount and complexity of regulations affecting industrial minerals has increased significantly in recent years. Nevada is no exception.

Jan 1, 1993

With commodity prices rising again and market conditions stabilizing, the Metals Economics Group (MEG) found that most mining companies increased their exploration budgets in 2010. In the groups 21st edition of the Corporate Exploration Strategies (CES), MEG found a 44-percent rise in the estimated worldwide exploration total for 2010. MEG found that the estimated total 2010 budget for nonferrous metals exploration reached $12.1 billion, reinstating almost two-thirds of the industry?s $6 billion in cuts to exploration in 2009. Nonferrous exploration refers to expenditures related to precious and base metals, diamonds, uranium and some industrial minerals; it excludes iron ore, aluminum, coal, and oil and gas. In 2008, exploration budgets were at an all-time high of $14.4 billion. This capped a six-year run in which budgets rose. In 2009, nonferrous exploration budgets dropped 42 percent in 2009 as the global economic crisis and declining prices for almost all commodities took their toll on the industry. Metals prices - the primary driver of exploration spending - have improved markedly since bottoming in early 2009, and have traded well above their long-term trends throughout 2010. In response, major, intermediate and junior companies have all increased their aggregate exploration allocations in 2010. In particular, the significant improvement in the availability of equity financings for the juniors over the past 12 to 18 months has allowed this group to account for the largest share of the overall increase in exploration spending this year.

Jan 1, 2011

By R. L. Miller

The potential for recovery of enriched uranium from spent nuclear fuel which has been consolidated into a nuclear waste form was explored in the studies reported here. The waste form of interest is iron-enriched basalt (IEB)--a silicate-based, fused-cast ceramic. IEB samples were prepared containing fuel assembly materials that simulate the core debris of Three Mile Island Unit II;1,2 the nominal composition of the consolidated waste form is given in Table 1. Ore Types The IEB samples, or man-made uranium ores (MMUO), are in two different mineralogical forms. Each MU0 was made by melting the constituent materials and holding at about 1500°C for 1 h. The MMUOs were then heat treated to control crystallization and crystal growth and then cooled to room temperature.

Jan 1, 1983

By Thomas W. Mitcham

A program of geological research in support of mineral exploration efforts is outlined. Specific goals are stated, approaches to accomplish their attainment are described, and the type of useful results to be expected are outlined. Because mineral exploration or prospecting has intensely practical goals, research in support of it must be applied research, applied to the problem of maintaining or increasing the discovery rate of the exploration effort. To attain research goals, attention to personnel selection, group structure, and program are critically important, and in about that order. A large percentage of the professional personnel should have had experience in mining geology or mineral exploration, and they all should be prospector-oriented. Structuring in the group should be at a minimum, with wide allowance for the kind of independent research which is essential to the nurturing of on-target creativity. The program should be field-oriented, and it should include a wide representation of those subdisciplines of geology which are applicable to mineral exploration. The types of results to be anticipated include improved or new conceptual models for various types of orebodies and their settings from which new ore guides can be derived, new exploration techniques, and the development of a knowledge bank for various aspects of the exploration effort.

Jan 1, 1968

By K. J. Ma, L. Ma, J. Stankus

The paper’s intent is to evaluate pumpable foamed cementitious mine seal material by determining the shear strength of a generic foamed cement in the laboratory. The tests were conducted on three scales: small-size specimens, consisting of cylinders 4 in. in diameter or 3-in. prisms; double shear medium- size specimens, measuring 13 in. by 10 in.; and large-size specimens, measuring 6 ft by 4 ft by 4 ft. The small-specimen shear tests resulted in average peak and residual shear strengths of 128 psi and 56 psi, respectively. These values are fairly consistent with published shear strengths of foamed cementitious material. However, the other two types of shear tests did not achieve the shear strength of a typical pumpable foamed cementitous mine seal material. Based on the test results, the paper concluded that the structural analysis of cement foam seals should be based on their residual shear strengths, approximately 20 psi, determined from small laboratory-scale tests of the cement foam/concrete or rock interface, and not be based on their peak strengths.

Jan 1, 2015

By J. A. Cole

Santa Fe Pacific Gold's Lone Tree mine is located in Humboldt County, NV, 45 km (28 miles) east of Winnemucca. The mine currently operates a 1.74-Mt/a (1.92-million stpy) run-of-mine heap-leach operation and a 2.27-kt/d (2500 stpd) refractory gold¬ore-processing plant. Most of the mill-grade ore reserves are refractory, mainly due to pyrite and arsenopyrite encapsulation of the gold. The autoclave pressure-oxidation circuit was commissioned in February 1994 to process the refractory ore. Mineralogy unique to the Lone Tree deposit allowed for the design of a partial-oxidation process. It takes advantage of the heterogeneous nature of the pyrite morphology. Partial oxidation has resulted in an autoclave plant that is able to achieve low operating-unit costs (Figs. 1 and 2).

Jan 1, 1995

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By Charles E. Dandois

New is a relative term, and, when used with reference to a concept as old as shaft kilns can be applied to a number of designs. In this case the design that is the subject of this paper, is known as the ring or annular shaft kiln as developed by Mr. Karl Beckenbach of West Germany. The first&apos; operating unit was rated 185 tons per day and was installed in 1962. Today, there are approximately 84 units in operation in Western Europe and Japan. Twenty-one additional units are in the process of erection or on order. Developed sizes range from approximately 100 to 330 tons per day. Units of over 500 tons are in the design stage, however, the largest units presently operating are rated 330 tons per day, <the first: of this size having been installed in 1966. "Figure" 1 is an elevation view of the unit. It is a single vertical cylinder to which are attached the required service platforms, combustion chambers, injectors and distribution piping. Auxiliaries such as recuperator, exhaust fan and dust collector are mounted on the appropriate service platform. The charging pan, feed conveyor, etc. are mounted at the kiln top. At the bottom of the kiln is the silo with a vibrator type discharger, and mounted separately is the required blower for injector air and fan for internal cooling.

Jan 1, 1973

By E. Manev

Thin aqueous equilibrium film studies and surface tension measurements on a mixed surfactant system consisting of polyethylene oxide (a model frother) and potassium ethyl xanthate (a model collector) enable the interaction between the two surfactants at the air/solution interface to be elucidated. For the film containing the non-ionic frother, the interface was charged and addition of low concentrations of xanthate acted as a common electrolyte and reduced the thickness of the film inducing rupture. However, at high xanthate collector concentrations, the negative charge xanthate was found to interact with the non-ionic and caused a build-up of negative charge at the air/solution. Higher frother concentrations were necessary to produce non-rupturing thin films upon increasing the xanthate concentration.

Jan 1, 1992

By W. E. Adkins

Ore and waste haulage usually constitute one of the major cost items in the operation of an open pit mine. This has always been true at the Chino mine, one of Kennecott Copper Corporation&apos;s western mines, located in southwestern New Mexico. The Chino Mines Division is an integrated operation. The open pit mine, dump leaching operation, and a precipitating plant are located at Santa Rita, New Mexico, and a power plant, mill, smelter, and fire refinery are located in Hurley, New Mexico, about nine miles south of the mine. Approximately 22,000 tons of ore are mined and processed each day; in addition, approximately 42,000 tons of waste are removed from the pit. Originally the pit was located along the side of Santa Rita Creek but it has deepened and expanded so that at the present time, it could better be described as a nearly circular pit about one to 1.5 miles in diameter. The bottom is at an elevation of 5750 feet, the west rim near the ore gathering yard is at an elevation of 6230 feet, and the highest bench on the east side of the pit is at an elevation of 6750 feet, giving a vertical mining depth of 1000 feet. The train waste dumps reach a maximum elevation of 6580 feet. At the present time, Chino uses electric locomotives, off-the- highway trucks, and a skip system for mine haulage.

Jan 1, 1963