Search Documents

By D. Bour, C. Nyikos, R. Curtice

Fire in a coal mine can be disastrous on many levels. In most cases, when a fire is detected, mining operations cease and all personnel are evacuated. Underground coal-mine fires are difficult to extinguish, can burn for a long time, and often result in an extended period of lost production. In a worst-case scenario, the mine is permanently sealed and abandoned, resulting in lost jobs, lost natural resources, and possible devastation of the local economy. In some cases, seals placed within the mine to isolate the fire could eliminate the need for sealing the entire mine and the subsequent extended delay in returning the mine to full operation. Previous attempts to place remote seals to extinguish mine fires in active mines have been largely unsuccessful. The West Elk mine experienced an underground fire in early 2000. The fire could not be accessed and extinguished from the active mine workings. A method of constructing seals remotely by drilling boreholes into the affected area was needed to help isolate and extinguish the fire. This paper describes the process by which remote seals were constructed that successfully isolated the fire and provided a means of extinguishing the fire by flooding the area with water. The period of lost production in the West Elk mine was considerably shorter than is typical in similar situations.

Jan 1, 2002

By M. J. Gilbey

Cross passageways between adjacent tunnels in passenger rail or transit systems may be used during train fire emergencies to evacuate passengers to points of safety in the non-incident tunnel. Rescue trains can be brought into the non-incident tunnel to remove passengers to expedite evacuation times as compared to walking along bench walls to the nearest egress stairs. In cases of multiple train emergencies, the required ventilation capacities can result in high pressure differences between the incident and non-incident tunnels. These pressure differences can make it difficult or impossible for a normal person to open doors of a cross passageway between adjacent tunnels. If opened, the velocity of the airflow through an open cross passageway can reach levels high enough to impede passenger evacuation. This paper describes the analysis of this problem for a sample rail tunnel. A ventilation concept that mitigates the problems of high cross passageway door opening forces and high velocities through open cross passageways is presented.

Jan 1, 2009

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

By N. Loganathan, Tan Boon Tee, Joe O’Carroll, Richard Flanagan

In recent years, tunnelling activities in Singapore have increased considerably with the construction of extensions to the existing sub-surface transport system, a deep tunnel sewerage disposal system, and tunnels for the laying power cables and other utilities. These tunnels are excavated through urban areas, adjacent to high-rise buildings, depressed road structures, beneath other tunnels, and buried services. Earth pressure balance (EPB) tunnel boring machines (TBM) have been used extensively in Singapore with great success. The risk associated with soft ground tunnelling, including tunnelling through Old Alluvium, can be minimized with an understanding of the geology, geotechnical parameters, and the tunnelling-induced behaviour of Old Alluvium (OA The purpose of this paper is to present some design and construction aspects of EPB TBM tunnelling through Old Alluvium.

Jan 1, 2005

By Kai Wang, Chao Xu, Qiang Fu, Tong Yang, Chunyu Zhao, Wei Zhao

The stress of a coal seam is an important factor that affects the permeability of the coal seam and then affects the coalbed methane (CBM) drainage. In China, adjacent coal seam mining is an important method to reduce stress, which increases the permeability of the coal seam. However, in the process of mining adjacent coal seams, many coal pillars remain, which causes stress concentrations and results in a decrease in permeability. Therefore, it is important to study the influence of coal pillars on the stress of adjacent layers and its distribution and evolution in the floor rock. This paper took the Shendong Baode Coal Mine as a case study and investigated the influence of the coal pillar on the stress and permeability of coal seam #11. The results show that under a coal pillar, the relationship between the vertical stress of different floor depths and the width of the coal pillar can be divided into a negative correlation zone, transition zone, and positive correlation zone. The change in the coal pillar width does not affect the pressure relief range or the degree of pressure relief in the adjacent coal seams below the goaf. The field measurements show that after the mining of panel #81,505, the permeability coefficient of coal seam #11 under the goaf increased from 0.1434 to 26.3545 m2/( MPa2*d), increasing 182.7 times, and the drainage mixing volume of boreholes #1 and #2 increased from 1.24 to 1.52 m3/ min. While the permeability coefficient of coal seam #11 from 12.5 m in the coal pillar has only increased by 2.6 times, the drainage volume of boreholes #3 and #4 did not change significantly.

Nov 19, 2022

By Raymond W. Henn

The 32nd annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 13-17, 2011. The field demonstration portion of the course was conducted June 16 at Baski Inc.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods per-formed under various field conditions. As part of the field demonstration, the class was shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and recorded conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results.

Jan 1, 2011

By E. C. Dowling, S. A. Elmquist, L. A. Kipfstuhl

The Cliffs and Associates Limited (CAL) 500,000 tpy HBI plant located in Trinidad was commissioned after modifications in early 2001. This plant employs the novel Lurgi Circored® process to reduce iron ore fines using a combination of circulating fluidized bed and conventional fluidized bed reactors in a hydrogen based. This paper will review the advantages offered by working in the Caribbean nation of Trinidad and Tobago, the Circored® processes, and plant start-up experience.

Jan 1, 2002

By M. D. Max, A. H. Johnson

INTRODUCTION Gas hydrates have considerable potential to be a major energy resource owing to their apparent abundance in Arctic regions and along continental margins throughout the world (Kvenvolden, 1988). Yet, the oil and gas industry has been slow to pursue this opportunity. The primary reasons for this are the large conventional reserve base for natural gas worldwide and the perception that gas hydrate will not be a viable resource for another twenty or thirty years. Gas hydrates are thus viewed as a potential resource for the distant future, but not a valid investment for the near term. This paper addresses both global gas markets and gas hydrate technology, and shows that the commercial development of gas hydrate could proceed rapidly enough to constitute a near-term energy resource. GLOBAL GAS MARKETS The proven worldwide reserves of conventional natural gas are truly enormous, totaling over 6,000 TCF according to BP (2004). Moreover, those reserves have nearly doubled during the past two decades and now represent 67 years of consumption at the current production rates of 80 TCF per year (Fig. 1). This reserve increase has occurred even as global production of natural gas has increased by 67% during the same two decades (Fig. 2). While declining conventional gas reserves are a concern in North America, especially in regions where established infrastructure exists to bring gas to consumers, large new discoveries continue to be made elsewhere in the world. Indeed, in many parts of the world (such as the Middle East and parts of West Africa), natural gas has been regarded as an essentially worthless byproduct of oil production or exists in stranded gas fields. Given this situation, pursuing unconventional gas resources that are inherently riskier exploration targets and more expensive to produce would appear to have little rationale from a business standpoint.

Jan 1, 2006

By C. O. Brawner, J. Kalejta II

The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than about 45°. As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result with less rock fall capacity. The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented.

Jan 1, 2002

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mud-stoneovercored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2000

By F. G. Heivilin

We are no longer short of viable Rare Earth deposits. As little as 2 years ago China mined and produced 97% ofthe world?s rare earths. Only a few deposits were in an advanced stage of exploration and development. Now Technical Metals Research (TMR) Gareth Hatch *5 reports that 347 deposits are being developed by 265 companies down from 440 on July 6th. Their Index of Advanced projects lists 45 projects in 14 countries. They will sustain the world for centuries to come and many good deposits are yet to be found. The problem is mining 14 elements in balance. Each of the deposits listing production in the chart has a unique set of minerals which they think will give them a cost advantage. Which of these will make it to production is a question. Most of the Advanced won?t be mined soon, but which ones? China is still in the driver?s seat in Light Rare Earth production (LREO) with one deposit with 35 million ton Baiyunebo deposit in Inner Mongolia which is part of a working iron ore deposit. The number of HREE deposits have been reduced and they attempting to eliminate unpermitted mines. This report will tell you what a Rare Earth is, how rare they are, why they are important, and where they are being developed which includes Australia, the United States, Africa, Greenland, Brazil and Canada.

Feb 27, 2013

By J. O. Marsden

Over the past eight years, Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold, Inc.) devoted a significant amount of effort to the development of a suite of processes for the effective hydrometallurgical treatment of copper sulfide concentrates. This effort resulted in the development of high-temperature (>200ºC) and medium-temperature (150° to 165ºC) pressure leaching processes. Specific configurations of both processes have been commercially demonstrated at Phelps Dodge?s facility in Bagdad, Arizona. This paper reviews in detail the chemistry of medium-temperature pressure leaching of copper concentrates and reports on the process development work conducted by Phelps Dodge and others for this technology. This paper is Part I of a four-part series on this technology. Part II covers the development of medium-temperature pressure leaching and direct electrowinning technology; Part III considers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By G. S. Takenaka

When Bridger Coal Company transformed their operations from surface mining to an underground longwall operation their plans included not only the addition of new mining equipment but also surface fans for a blowing (supply) air ventilation system. The original system concept included a propane gas fired air heater to preheat the intake air during cold weather and a dual parallel fan and duct system. One fan operated to ventilate the mine while the other fan was for stand-by emergency operation. Equipment proposals were submitted in March, 2005 based on the dual parallel fan system. Discussions conducted during the equipment selection process revealed that several alternative system design concepts were available. The alternative concepts included innovation features that not only saved space and cost but also reduced operating expense as well. Many of the features were incorporated into the final design of the system. A comparison of the original system concept and final installation design are presented in the paper in addition to details of the features and the derived benefits.

Jan 1, 2009

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

By B. Moore, Y. J. Zhang

In today’s competitive dimensional stone business environment, use of available technology is critical to achieve and maintain a competitive advantage. Awareness of improvements in diamond cutting technology, operation planning/scheduling, and geotechnical data manipulation/implementation are the keys to success. This paper presents the modern techniques of limestone sawing and quarrying developed and adopted by Indiana Limestone Company, Inc.(ILCI).To fulfill the growing market demands, ILCI’s quarries are committed to deliver planned quantities of all type of stone blocks in a variety of different colors, sizes, and textures. This involves scheduling which quarry ledges should be mined and when in order to minimize unnecessary inventory buildup. Challenges associated with ILCI’s operation are discussed and summarized in the closing of this paper.

Jan 1, 2004

By Mohamed Yusuff

Modern transportation systems are one of the most important achievements of our civilization and provide us with tools for broadening individual and social freedom of choice. The transportation system initiated today is handed dawn to the next generation, probably with little choice because of the enormous expenditure of monies involved, and influence their way of life as to where they should live and where they should work. The ever increasing antagonism between the citizens and the planners of the transportation systems necessitates a careful review of the entire planning process. The planning process can be broadly classified into: the goal formulation and decision making process; the plan development process; and the plan implementation process. THE GOAL FORMULATION AND DECISION MAKING PROCESS Goal formulation and decision making is one of the vital phases of the planning process and is primarily based upon social values. In measuring social values, the planner must employ an appropriate scale of measurement since in the absence of this yardstick, these values tend to became vague and abstract ideals. The need for major social programs and concerns (poverty, etc.) of the urban areas should be analyzed to determine the type of transportation system which would contribute to the solution.

Jan 1, 1974

By R. A. Franks

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system?s ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system?s ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2008

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008