Search Documents

By Ernst P. Hall

The Irwin Basin. (Fig. 1)* is a synclinal or shoe-horn *Figure numbers throughout refer to color slides not included with the preprint shaped basin in the Pittsburgh Coal Seam, It is approximately 10 miles wide and 22 miles long at its maximum points. The surface of the land above the basin is hilly, rolling farmland,, typical of this area of Pennsylvania, and it is criss-crossed with streams and highways and liberally dotted with farm houses and communities. In-general the coal is pitched from north to south with a total drop of 610 feet'. The coal seam cross-section from east to west is bowl-shaped and rises as much as 375 feet from the low point of the bowl to-the-outcrop. Cross-sections showing coal elevations are shown on Figs, 4 and 50 Ground cover above the coal will vary from 0 to 550 feet, averaging about 350 feet throughout the area. This area is richly endowed with a history of coal mining. The first car of coal shipped cast of the Allegheny Mountains was mined in the Westmoreland Coal Company's Shady Grove (later North Side) Colliery in Irwin, Pa., early in 1853, This mine was opened in 1852 by Coleman, Hillman & Company. The coal was hauled from the mine to the freight station by horse-drawn wagon and. loaded into a then "standard" box car of 18,000-pound capacity. Coal mining in this region flourished and grew as steel production in nearby Pittsburgh demanded more and more of the high quality, metallurgical-grade coal of the region.

Jan 1, 1959

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By Syd S. Peng

Introduction Modern longwall mining, introduced to the US coal industry in the mid-1960s, is the latest coal mining technique. Today, longwall mining produces more than 15% of all underground coal production. The growth of longwall mining in the US is slow. However, nearly two decades of longwall mining have demonstrated that its benefits outweigh the disadvantages. Longwall Advantages Production and Economics - A typical longwall production ranges mostly from 0.9 to 1.8 kt (1000 to 2000 st) of clean coal per shift. This is about three to six times the production of comparable continuous mining units. Furthermore, there are much less rejects in longwall mining, typically 15% to 25%. It must be noted, however, that a new longwall with an inexperienced crew may produce less, depending on mining conditions. But as experience gains, production increases rapidly. Due to its high production, the cost per ton of coal mined over the mine's lifetime is cheaper with longwall mining than with continuous mining. A study on a conceptual mine of 25 year life using actual operational data (Dangerfield, 1981) concluded that the cost per ton of coal mined is 32% cheaper by longwall than by continuous mining. Another benefit from its high production potential is that it enables the production to be concentrated in a few longwall faces versus many units of continuous mining required to achieve a similar production. As a result, mine organization and management simplify considerably. Safety and Savings - Most US longwalls use shield supports that cover the roof with solid canopy and isolate a gob completely from the face area. Thus, if the supports are properly selected and operated, the potential for roof fall accident is almost zero. Furthermore, it is not unusual that a well-run longwall face is much more orderly and cleaner that most well-run machine shops. The ventilation system for longwall mining is the most ideal type. It is simple and unique. No auxiliary fans are required. The fresh air sweeps through the whole face. Its volume and velocity can be adjusted as demanded. Recovery - In spite of multiple entries layout for US longwall panels, the longwall method recovers up to 40% more coal than the continuous mining method (Dangerfield, 1981). The typical recovery for longwall mining is 70% to 85% versus 45% to 80% for continuous mining. Versatility - Longwall mining has been employed successfully in seam heights ranging from 0.8 to 3.7 m (2.7 to 12 ft); in seam inclinations from horizontal to 35°; in overburden depths from 46 to 914 m (150 to 3000 ft); in single or multiple seam mining; and in uniform or irregular seam characteristics. For seam height less than 1.2 m (4 ft), the plow is used instead of a shearer. However, in spite of recent developments, the plow still is unsuitable for hard coal seams. Slow Acceptance How come longwall mining, with so many advantages, has not spread more rapidly? Undoubtedly, the major reason is the large capital investment required. Under normal market conditions, the capital required for a longwall panel ranges from $7 to $11 million. Another factor is the uncertainty of its applicability to any specific coal seam of interest where longwall has not been used or operated successfully. Although longwall mining elsewhere has proven its applicability to wide-ranging seam conditions, there have been several failures in the past two decades. Analyses of those cases show that most failures can be attributed to inexperience, both operational and technical, including equipment selection. Therefore, personnel training on the longwall mining technique is absolutely necessary before its initial operation. Some earlier statements about adverse surface subsidence associated with longwall mining were misleading. Research has proven that surface subsidence under longwall mining is controllable and predictable. And, if longwall mining was mandatory since the onset of coal mining in the US, there would be no surface subsidence problems over abandoned mined land today. It is a blessing that surface subsidence occurs

Jan 3, 1985

By Peter J. Rafferty, Friedrich Steinhäusler

INTRODUCTION The Nuclear Energy Agency plays an active role in promoting international cooperation among its member countries in the field of nuclear energy. In addition to various other functions, it plays a major role in encouraging harmonisation of government regulatory policies and practices, promoting exchange of information, and coordination of research and development in the field of radiological health and safety associated with nuclear fuel cycle activities. The work of the Agency is carried out through a number of specialised standing committees. In particular, the Committee on Radiation Protection and Public Health (CRPPH) is responsible for the Agency's activities concerned with radiological protection and related environmental problems. Its functions include review and discussion of national radiation protection policies and practices, review of developments in radiological protection, interpretation of ICRP recommendations and the study of the means of their translation into practical applications, including the establishment of radiological protection standards. Its functions also include the preparation of technical studies and reviews on specific problems requiring attention, and coordination of further research and development at the international level. Major attention is presently being given to the NEA programme of work on problems associated with radiation protection and environmental impact of nuclear fuel cycle activities, with particular attention to the front-end (uranium mining and milling) and the back-end (waste management) of the fuel cycle. In this context, the increasing attention that has been given in several countries to the problems associated with the exposure of man to radon, thoron and their daughters, and with their dosimetry and measurement, were readily appreciated by NEA, which began an active programme of work in this field in 1976. Because of the detrimental health effects,as demonstrated by epidemiological studies,caused by prolonged exposure to excessive levels of shortlived daughters of radon, particularly in poorly ventilated underground mines, the bulk of attention and needed effort has been focussed on radon and radon daughters in uranium mining. In certain countries some concern has been expressed also about the significant levels of exposure experienced by workers in non-uranium mines,and members of the public who live in particular areas or in dwellings built with particular materials which produce higher than average levels of radon and radon daughters. However, at the time of the first NEA involvement in this field it was considered that one of the most urgent problems to be solved was that of ensuring adequate personal dosimetry for uranium miners. Consequently, the NEA was urged to organise a specialist meeting on personal dosimetry and area monitoring for radon and radon daughters to provide an international forum for exchanging information and reviewing problems in this field. The meeting was held in Elliot Lake, Canada, in October 1976. A second specialist meeting, on the same subject, was held in Paris, in November 1978, to review further developments in this area. These meetings demonstrated that the overall problem associated with exposure to radon and radon daughters had many facets, each of which in recent years has been the subject of considerable attention in many countries for different reasons. It emerged from the meetings that further work was required on a variety of issues in two main areas: 1) dosimetry 2) metrology and monitoring. Conclusions and recommendations which emerged from the two NEA specialist meetings were discussed by the CRPPH. As a consequence the Committee approved, in September 1979, a detailed programme of work in the area of dosimetry and monitoring of radon, thoron and their daughters, and approved the setting up of an international Group of Experts on Radon Dosimetry and Monitoring to undertake the work. The work has been divided into two phases - phase I, on dosimetric aspects, and phase II, on metrology and monitoring aspects. The terms of reference of the work are given in Appendix 1. A list of national representatives on the Group of Experts on Radon Dosimetry and Monitoring is given in Appendix 2; many of these persons are participating here in the Conference. The Group of Experts met for the first time in April 1980 and met again in September 1981. The work of phase I is nearing completion and a report is expected to be submitted soon to the CRPPH for its consideration. Three technical papers providing interim information on the study appear elsewhere in the proceedings of this Conference. The papers cover the three principle areas examined in the study so far: 1) dosimetric aspects 2) review of the "working level" 3) review of objectives and requirements for measurement and monitoring of radon, thoron and daughters. The authors, their affiliations, and the titles of these papers are listed in Appendix 3. A brief overview follows giving the principal results.

Jan 1, 1981

By S. McMurray

INTRODUCTION Towards the end of the 1890s the attention of a prospector by the name of Thomas Cullinan was drawn to the occurrence of alluvial diamonds east of Pretoria. Persistent prospecting work by Cullinan led to the loca¬tion of the source of these diamonds-a kimberlite pipe on the Elandsfontein farm. Cullinan eventually acquired the property in 1902, and during an extensive evaluation program outlined the largest diamondiferous pipe in South Africa on which the Premier mine was established. Worldwide attention was drawn to this mine in 1905 when the Cullinan diamond, which weighed 3106 carats and is by far the largest gem diamond ever discovered, was recovered. Premier mine operated with varying success until 1932 when the worldwide depression forced it to close. In 1945 the mine was reopened and since then has been a major producer of gem and industrial diamonds. During the early 1950s exploratory drilling revealed that below the 370-m level the pipe had been completely cut off by a younger gabbro sill. This sill has created major mining and metallurgical problems but the existence of vast reserves of high grade ore below it justi¬fied the establishment of virtually a new mine below the sill. Detailed planning of below-the-sill mining is nearing completion and the development of the first mining block (the L1 block) is well advanced. A full discus¬sion of this block follows. GEOLOGY OF PREMIER MINE Pipe Morphology and Country-Rock Geology As can be seen in Fig. 1, Premier mine is an elon¬gated oval shape with a long axis of 900 m on the surface and a short axis of 450 m. The pipe has a surface area of 32 hectares which decreases progres¬sively with increasing depth, so that 500 m below the surface the area is reduced to 22 hectares. The contact between the kimberlite and the surrounding country rock is sharp, with an average angle of dip of 1.48 rad (85°). From the surface down to approximately 350 m, the country rock is a felsite which grades downwards into a norite. In general both rock types are hard and massive, the felsite in particular being poorly jointed. This characteristic combined with other factors results in an extremely stable open pit, and near-vertical side¬walls are currently being maintained. The norite in general is competent but is heavily jointed in some areas resulting in very blocky ground which creates localized tunnel support problems. In the southeastern area below the sill a zone of highly altered and very unstable norite, which has also created localized sup¬port and development difficulties, lies adjacent to the pipe contact. Kimberlite Geology The Premier pipe is a complex multiple intrusion which contains in the region of 15 separate types of kimberlite, most of which are volumetrically insignifi¬cant. On a simplified basis three major types can be identified which correspond to three separate phases of intrusion. They are: Brown Kimberlite: This represents the first phase of intrusion and now occupies the eastern part of the pipe. In plan the brown kimberlite has a crescentric shape resulting from the intrusive relationship with the younger gray kimberlite which lies to the west. The brown kimberlite increases in relative area with increas¬ing depth which is a favorable factor for future mining operations since this kimberlite is the richest area of the mine, having an average grade of 70 carats/ 100 t. Below the sill this rock disintegrates extremely rapidly when exposed to air or water, to form a fine gravel-like material. This characteristic is due to a high montmorilonite clay content. As is common with clay minerals of this type, water can be absorbed into the crystal lattice with a resultant increase in volume which causes the physical decomposition of the rock. The presence of this decomposing kimberlite was a major factor governing the choice of a mining method, as well as development and tunnel support techniques. Gray Kimberlite: This is the most abundant type and represents the second major phase of intrusion. The diamond content is variable depending on the amount of waste rock dilution, and in general the rock is stable and non-decomposing. At the time of formation of Premier, the surface rock type was Waterberg quartzite, a rock formation which has subsequently been removed from this area by erosion. The explosive extrusion of the gray kimberlite caused extensive brecciation of this rock and while the kimberlite was in a mobile state huge masses of quartz¬ite, amounting to tens of millions of tons, slumped into the pipe. This quartzite became concentrated in the central area of the mine and has been a major mining problem throughout the history of Premier since, due to the irregular distribution of the quartzite, effective selective mining has never been possible. The quartzite is therefore extracted with the ore and has a significant dilution effect on the overall grade. Black Kimberlite: In the western part of the pipe a circular, pluglike body of kimberlite is intruded into the gray kimberlite. This plug consists mainly of a hard, dark-colored rock known as black kimberlite, but also contains a number of minor kimberlite variet.ies as well as nonkimberlite carbonate dikes. The Gabbro Sill The sill averages 75 m in thickness and within the confines of the pipe consists of 52 million t of rock. On average the major dip is 0.34 rad (20°) to the northeast which is across the short axis of the pipe, the range of dip being from near horizontal up to 0.52 rad (30°). Due to the pronounced dip, the sill is encount¬ered over a vertical distance of 175 m with the highest upper contacts on the 355-m horizon and the lowest bottom contact on the 530-m horizon.

Jan 1, 1982

By Rodolfo V. de la Cruz

This paper describes the development of a new method and device for determining the in-situ mechanical properties of rock masses. The method involves a self-recording mechanical deformation gauge for sensing-recording she deformation of the borehole wall when loaded hydraulically. The self-recording feature of the gauge eliminates the difficult technical problem of transmitting signals over very long cables for measurements at great depths. Adopting a mechanical gauge instead of electronic, electrical, optical or grid techniques eliminates delicate instrumentation and installation problems. Moreover, mechanical gauges are inherently rugged and suitable for use in severe borehole conditions including very high temperatures. The technique was tested in limestone, basalt and granite specimen. The calculated mechanical property values for 1 the tests agree with those obtained by conventional testing methods. The self-recording mechanical deformation gauge has a minimum reading of 50 micro inches (1.27 x 10-3mm), comparable with electrical resistance strain gauges, capable of reading deformations over a range of 0.25 inches (6.35mm). The sensitivity, ease and accuracy of the method recommends it highly for in-situ rock modulus measurements.

Jan 1, 1980

By W. G. Miller

A series of computer programs for the analysis and mapping of coal-related data has been developed at the Illinois State Geological Survey; these programs, known collectively as the Coal Data System, represent the latest achievements in computer processing of geologic data at the Survey. Building upon programs previously developed in the Survey's Computer Services Unit, they expand the scope of the computerized data base that the Survey has been using for analyzing coal-related data. The System was partially developed during a joint study by the Illinois State Water Survey and the Geological Survey entitled, ?Coal and Water Resources for Coal Conversion in Illinois.? 2 In that study the available coal reserves more than 42 inches thick in the two principal coal seams throughout the state were mapped. The System was used to calculate the coal reserves and to report the average number of tons of coal in place per square mile in each township (Figures 1 and 2). It also produced maps of the coal features of sufficient quality to be printed on material that was scribed as master copy for the printing of full-color 1:500,000 scale maps (see Figures 3 and 4).

Jan 1, 1975

By T. F. Tomb

on' January 6, ,1992, the Mine Safety and Health Administration (MSHA) issued an Advanced Notice of Proposed Rule Making (ANPRM) for diesel particulate (DP). The ANPRM identified five areas where the Agency was seeking additional information to assist in the rule making process. These areas were exposure 'limits, risk assessment, consideration of other information, sampling and monitoring methods, and feasibility. The period for submitting information relative to the ANPRM closed July 10, 1992. Prior to issuance of the ANPRM, the agency was involved in conducting studies to evaluate sampling and control technologies and to gather information with respect to occupational exposures to diesel particulate in underground mining operations employing diesel-powered equipment. Since issuance of the notice, additional studies have been conducted to provide supplementary information in these specific areas. Results of these additional studies indicate that average DP levels in coal mines not using aftertreatment range from 0.9 to 2.1 mg/m3. Aftertreatment devices can reduce these levels by approximately 50 to 90 percent. Studies conducted in metal and nonmetal mines showed average DP levels ranging from 0.3 to 1.6 mg/m3.

Jan 1, 1994

By J. G. Davis

Continental Oil Company has spent over four years of research on the fundamentals of potash solution mining. This work included laboratory investigations of salt solution, brine flow, selective extraction of KC1 from sylvinite, and control of cavity geometry. Laboratory results were expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well mining systems were studied in the field work. The current paper discusses one field test in which potash was solution mined from a thin sylvinite ore zone in the Carlsbad Potash Basin. A two-well mining system was used for this test. The potential economic value of solution mining has been recognized for many years, and applicable United States patents date back into the past century. Principal advantages of the process over conventional mining include (1) the use of drilled holes and solution techniques in- stead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths.

Jan 1, 1969

By Thornton L. Neathery

A small area in the Alabama Piedmont was studied to determine if metallic enrichment was associated with local magnetic anomalies. Cores from two holes in these magnetic anomalous areas have sulfide (pyrite, pyrrhotite, chalcopyrite) film on slicken-side and fracture surfaces. Two hundred and fifty soil samples were collected from the top of the "B" horizon on 1, 000 foot centers over the general trend of magnetic anomalies. Soil samples were leached with a 1:2. 7 mixture of HF and H2SO4 and the dilute filtrate analyzed for Cu, Pb, Zn, Ni, Co, Cr, Mo, and Cd, using atomic absorption methods. Concentration-value maps were prepared for each element. Small areas of anomalous concentrations were defined for Cu, Pb, Zn, Mo, and Ni. Some of these areas generally coincides with magnetic anomalies. Concentration values (ppm) range from: Cu 165.0 - 0. 5; Pb 265. 0 - 0.0; Zn 1386.0 - 43. 0; Ni 187.0 - 10.0; Co 207.0 - 6. 5; Cr 117.5 - 2.0; Mo 95.0 - 0.0; and Cd 32. 5 - 2.0. Studies of other magnetic anomalies appear warranted.

Jan 1, 1972

By B Scheiner, D. A. Stanley

Introduction Treatment of ores to recover metal and mineral values results in waste materials usually in the form of dilute slurries. The US Bureau of Mines (USBM) investigated a technique for dewatering phosphatic clay waste by flocculating with polyethylene oxide (PEO) and dewatering the resulting floes on a static screen and/or trommel screen (Schemer et al., 1985). In the investigation, it was determined that PEO was far superior to polyacrylamide polymers for this type of dewatering. This paper discusses reasons for this superior performance. Comparison of PEO with polyacrylamides Dewatering experiments were conducted by adding PEO solution from a burette to a stirred clay slurry. The dewatering endpoint was characterized by rotation of the floc mass as a unit, a clear supernate, a maximum floc size, and a minimum floc volume. Additional water was removed from the floes by hand squeezing (Schemer et al., 1985). The clays investigated were sodium, potassium, magnesium, calcium, and aluminum exchanged montmorillonite and attapulgite. Nine commercially available (Superfloc) polyacrylamides were compared with PEO at two polymer concentrations. Results are summarized in Table 1. The solids content of the dewatered clays ranged between 24% and 33% and was highest for PEO-treated material. These results and the data in Table 1 indicate that PEO is superior to polyacrylamide in terms of polymer dosage required. Superflocs 16 through 128, like PEO, are nonionic and should give similar results to those for PEO if the flocculation mechanism is the same for both type polymers. Superflocs 204 through 214 are anionic with increasing anionic character from 204 to 214. Generally, the anionic polymers gave the best results for the polyacrylamides tested, but in terms of dosage they were not as good as PEO. Correlation between flocculation and dewaterability of waste slurries The overall mechanism for mechanically induced clay dewatering is not completely known, but certain observations can be made. For instance, when a polymer is adsorbed on a clay such as montmorillonite, the polymer desorbs interlayer water. Polymer adsorption is driven by favorable entropy changes associated with this water desorption. It is also known that the -CH2-CH2- links of the PEO chain are sufficiently hydrophobic to lead to physical adsorption of the polymer (Theng, 1979). For montmorillonite slurries, the sheet-like fundamental particles, called tactoids, consist of a small, variable number of aluminosilicate layers together with interlayer water and exchange ions. The flocculation process consists of adsorption of polymer on the tactoid. Loops and tails of polymer that extend into solution then adsorb on another tactoid, forming a bridge. Mechanical action, induced by hand squeezing or in a trammel, joins the bridged tactoids face-to-face and edge-to-edge to form regions of high density. Similar orientation effects are observed for the needle-like attapulgite crystals (Schemer et al., 1985). Proposed flocculation model Generally, statements concerning flocculation and dewaterability apply to both PEO and the polyacrylamides. However, PEO has additional interaction with the clay material when compared with polyacrylamides. PEO is a polymer with repeating -CH2-CH2-O- groups and interacts with montmorillonite through a water bridge whose strength is greatly influenced by the exchange ion. To obtain insight into this interaction, a series of experiments were conducted in which different ion exchange forms of montmorillonite and attapulgite clays

Jan 1, 1987

By Joseph T. Duncan, Syd Peng, Larry G. Stolarczyk

The mining business has numerous risks: equipment availability, labor disruptions, foreign exchange rate, etc., but one of the more important risks is assessing the geology. Improving the “intelligence” of geology can and will have significant positive effect on reducing mining risk and thus enhancing operational and financial performance. The use of the advanced Radio Imaging Method (RIM-IV) on coal seams and ore bodies can create useful two-dimensional (2-D) and three-dimensional (3-D) high-resolution images that provide mining engineers with additional intelligence to better plan and improve operations. Improved operational performance will reduce costs and enable mining companies to meet market and financial commitments. For the past decade the underground coal mining industry has been moving toward “super panels” in long-wall mining, and “super sections” for room-and-pillar mining. These mining conventions employ wider faces, longer gate roads, greater room-and-pillar density, and an increased scale in the amount and complexity of mining equipment. An obvious economy of scale exists: amortization of setup investments over greater volume of coal enables mine management to reduce fixed cost per ton. Restricted by equipment considerations, face widths have currently reached about 1,100 ft. Wider longwall panels are planned, with 1,400-ft widths, but this requires an incremental step in hardware that the original equipment manufacturers will soon bring to market. However, longwall panel length has not yet reached its limits, with some panels planned up to 25,000 ft. While longwall panel length is generally dictated by reserve size and extent, practical restrictions in mine planning also include seam thickness, ventilation requirements, or restrictions involving methane drainage. Super panels have certainly enabled the industry to keep pushing the limits of productivity improvement. However, important considerations in mine planning, now and especially in the future, will be driven in large part by geological factors. While larger developments improve productivity and capture economies of scale, the fact that super panels can contain at least four times the area or coal volume means that the probability of encountering serious anomalies is at least four times greater than with the “conventional” panels. Given the increased probability of encountering anomalies, improved assessment of geology is important for super panels and super sections. Proper due diligence requires a thorough and competent evaluation of a mining property and its ore reserve. Using improved geostatistical techniques is most important, and improving the base data for the analysis is equally important. The old cliché “garbage in, garbage out” certainly applies. Also, the quality of coal reserves is (or has been) declining, so, in the future, mining will be in deeper and most likely thinner seams—and these seams appear to contain greater anomalies that threaten efficient operations. To counter the impact of reserve deterioration, the industry is moving toward greater use of geophysical tools and services. Fortunately, tools such as the Radio Imaging Method™ (RIM-IV) system have been improved and can provide the industry with enhanced 2-D and 3-D images of coal seams and ore bodies. To identify and profile the best areas of a coal reserve, geologists, engineers, and mine managers need greater intelligence in the form of RIM-IV tomographic maps of longwall panels and room-and-pillar sections. These images have enhanced the understanding of in-seam features, which in turn has improved operational plans and performance.

Jan 1, 2005

By H. Janas

In a gas/coal outburst the gas plays an active, driving part. The proneness of coal to outbursts can be determined by means of its gas emission properties, since coal that is liable to outbursts differs from coal with normal gas emission properties in that it liberates its gas from the sorptive bond more quickly. There is a risk of outburst when the flow of metha¬ne originally desorbed by the coal is sufficient to move the loosened coal which has been broken suddenly. The violence of a gas/coal outburst can be evaluated from the distance of projection of the mass of coal. It depends on the gas pressure and on the liability to outburst of the coal at the original centre of the outburst. Both factors are complementary in their effects so that the same work is done in a gas/coal outburst when there is a high gas pressure and low proneness to outburst as when there is a low gas pressure and a higher proneness to outburst. The gas pressure in the coal increases with its gas content. Consequently it is possible to deduce the gas pressure of a coal seam from its gas content. In the Federal Republic of Germany the risk of a gas/coal outburst is thought to exist when the desorbable gas content of the coal reaches or exceeds the value of 9 m3/ton and if the specific limit value of the proneness to outburst is exeeded. The Mine Ventilation Testing Station of the Westfalische Berggewerkschaftskasse has developed a new method for determining the risk of gas outbursts immediately after taking the samples at the coal face (1), (2).

Jan 1, 1980

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

In the UK as existing face capacity is replaced, many of the new faces will have higher installed powers and be located in zones of higher strata temperature. These factors coupled with the need to increase production will result in more faces experiencing environmental difficulies, especially with respect to climatic conditions. In many cases these problems are unlikely to be solved, as in the past, by simply increasing the face air quantity. Therefore other techniques including refrigeration will be necessary, possibly requiring major capital and operational expenditure. It is easy to spend large capital sums and incur high operational expenditure without achieving the desired amount of climatic control. There is therefore a great need for reliable prediction techniques to aid in the making of sound, informed decisions which will have a significant influence in the long term on the level of production costs. A computer program able to predict the heat flows and resultant climatic conditions on a long¬wall coalfaces has been developed. Throughout it's development underground measurements have been used to validate the computer model and it has been shown that for an advancing coalface under normal production conditions that the program predicts the climate to within 1°C of the measured conditions. This paper outlines a number of methods available to improve climatic conditions on longwall faces. The coalface temperature prediction program is used to quantify the effects of these methods on the climatic conditions for a model coalface and a comparison is given. In conclusion a cool¬ing strategy for longwall faces is outlined.

Jan 1, 1991

By J. Alton Burks, Roy C. Bartholomae

The chain conveyor is utilized extensively in underground mining to convey raw ore, especially coal. It is estimated that several thousand loading and continuous mining machines rely on this type of conveyance. Although the chain conveyor is both efficient and highly reliable, its use is generally associated with the production of noise levels that often exceed 105 dBA at the operator's position. Thus, it is one of the most significant contributors to the occupational noise problem experienced by miners in the underground coal mining environment. Conventional engineering noise controls that result in an average reduction of 4 dBA have been previously designed and implemented. However, a novel solution involving a change in conveyor operation has been proposed that takes advantage of two aspects of conveyor noise: 1) conveyor noise has an approximately cubic dependence on conveyor chain speed and 2) due to the damping provided by coal, a full conveyor is 5 dBA quieter than an empty one. An engineering analysis has shown that a significant reduction in the operating noise level of a typical continuous miner can be achieved through the use of an adjustable speed drive automatically controlled by a coal loading sensor that maintains a full conveyor at all times. The potential reduction depends primarily on the mining conditions (coal seam thickness and the presence of either rock or water) and varies from 7-18 dBA. Other benefits to be derived from the use of a variable speed drive include reductions in power consumption, dust, and maintenance costs.

Jan 1, 1992

By Broderick E. Davis

Each year, about 45 Mt (50 million st) of flotation tailings are discarded in Florida phosphate operations. These tailings only contain about 4% of the phosphate in the ore. However, more than half of the phosphate in the tailings is concentrated in the +600 µm (+28 mesh) size fraction at grades of up to 20% P205. Many phosphate producers have attempted to solve this problem by floating the +425 µm (+35 mesh) flotation feed separately. However, phosphate recoveries in these circuits are typically only 60%. For seven sampled phosphate operations, the phosphate content of the +600 µm (+28 mesh) fatty acid tailings ranged from 15% to 25% P205. In every case, the +600 µm (+28 mesh) fatty acid tailings was higher in grade than the overall flotation feed. Attempts to efficiently recover this coarse phosphate have apparently been unsuccessful at these seven phosphate operations. Recovery of this coarse phosphate would provide an additional 900 kt to 2.5 Mt (I to 2.7 million st) of phosphate annually and add an additional year to the reserves of these important deposits. A typical central Florida phosphate matrix is composed of three different mixtures of minerals. The +1.18 mm (+ 16 mesh) portion is chiefly phosphate pebbles and is beneficiated by sizing. The -106 µm (-150 mesh) portion contains virtually all of the clay minerals and is discarded in the hydrocyclone overflow. The -l mm +106 µm (-16 +150 mesh) material is a mixture of quartz and phosphate minerals.

Jan 1, 1993

By H. W. Gussmann, R. G. Rohrs, E. van der Merwe

Salinity in Effluents carries a high penalty as a result of toxic­ity, corrosion, limited re-use potential, scaling and environmental impact. Although the high TDS, such as Calcium sulfate, other than metals are still being dealt with a low key non issue basis, they are receiving more and more attention from regulators. Traditional solutions to solve these problems are costly and inefficient and create therefore severe constraints on the prof­itability of mining operations and out-price in general the finan­cial resources for environmental clean up operations. Going up the technology versus cost curve the most econom­ic solution to pollution is dilution but which is difficult in a coun­t1y shoti of water. If this can't be done, the second best, at least in sunny areas, is, to pump the whole effluent on a tailings dam for evaporation. Depending on the contaminants, one may have to pond the efflu­ent to avoid re-dissolution and seepage into the ground. The next most common solution to pollution is the addition of lime to remove and concentrate any dissolved metals and then dump the product, hidden in a mass of gypsum in a convenient place. Again ponding may be required to avoid ground pollution. However the treatment costs start to rise steeply if it is not allowed to discharge the limed overflow solution because of its high calcium sulphate content. Further treatment is then required in the form of high cost and high tech membrane process tech­nology such as reverse osmosis or dialysis or even mechanical driven evaporation.

Jan 1, 1998

By V. P. Petrov, V. S. Znamensky

There are a great number of asbestos deposits in the USSR, and some are quite large. The main deposits of chrysotile asbestos are shown in Fig. 1. The Bazhenovo deposit, which is located in the Sverdlovsk region, is the largest and has been mined since 1889. Systematic studies of asbestos deposits were begun from the very be- ginning of Soviet government and are most often connected with the names K.E. Tarasov, P.M. Tatarinov, B.J. Merenkov, N.D. Sobolev, F.V. Syromjatnikov, V.N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V.R. Artemov, and V.F. Dybkov. Investigations by these people and others helped the USSR be one of the most important producers of asbestos in the world. In this chapter, the main asbestos deposits of the USSR are explained in a general outline from the point of view of their genesis, common features, and differences that must be taken into account for forecasting, exploration, and the mining of asbestos. All chrysotile asbestos deposits of the USSR were formed from magnesium rock as a result of comparatively low grade temperature, hydrothermal alteration, and free crystallization of fibrous chrysotile in open cavities that served as catalysts. Chrysotile, a widely distributed rock-forming mineral, is not in general an important mineral for industry as it is a long fibrous and main vein variety. However, it must serve for geologists as an important prospecting criteria. And, the geologist should search for the mineral not only in places of possible chrysotile generation, but in places where asbestos may be crystallized in its long fibers. The Soviet geologists distinguish chrysotile asbestos deposits in two groups: (1) ultrabasic rocks and (2) sedimentary dolomite terranes, taking into account how the maternal rock was affected by hydrothermal solutions. The largest deposits are related to ultrabasite. In dolomite, the largest deposits are small and their asbestos contains almost no iron, which makes it a better filler for insulating plastics. There are a few types of asbestos deposits within the limits of the ultrabasic group, the largest being a Bazhenovo type to which the deposits of the Urals are attributed. This Bazhenovo asbestos is characterized by the most complete zonality of disposition for various kinds of asbestization. These types of deposits are, for the most part, the only ones presently working in the USSR. The Bazhenovo deposit is connected to the gabbro-peridotite intrusive belt that is about 180 km long and is broken into a number of fault blocks as shown in Fig. 2. Granitoid veins of intruded rocks are found along the deepest faults, and were sources of hydrothermal solutions that affected the maternal rock. The nearest granitoid vein, ultrabasite, is substituted by listwanite that consists of quartz, talc, carbonate, and some other essentially talcous rock. The next zone of hydrothermal alteration is composed of serpentine. The boundry between serpentinite and unaltered ultrabasite is as irregular, diffuse, and rough as the boundaries between all other zones. Nearer the vein of granitic rock, ultrabasite is entirely serpentinized into massif serpentinization that penetrates through cracks and fissures. There is an unaltered ultrabasite space between fissures, and the biggest block is preserved unaltered in the central part of the massif. The Soviet geologists call this ultrabasic sopka. Preservation of the unchanged blocks is of great importance for deposit formation as volume changes are impossible during the process of asbestization and serpentinization. It may be confidently said that asbestization in Bazhenovo type deposits is possible only when alteration of ultrabasite has not completely occurred. Under conditions of massif volume, a very big mass of substance must be carried out of the ultrabasite for the progressive stage of serpentinization. However, in the regressive stage,

Jan 1, 1986

By Warren D. Stanford

The Alligator Ridge mine is a near-surface gold mine located in a remote area 113 km (70 miles) northwest of Ely, NV. The deposit was discovered in 1976 by a lone prospector working under a grubstake contract for Amselco Minerals Inc. Evaluation of mine potential proceeded quickly. Favorable drilling results led to feasibility and mine design studies by the end of 1978. Mine construction began in early 1980. By September of that year, the process plant was fully operational. The first gold was poured a few months later. Alligator Ridge is designed to produce 1.9 t (60,000 oz) of gold each year. The projected mine life, based on proven reserves, is to mid-1988. However, Amselco is actively conducting exploration nearby for additional reserves to extend the mine's life. Amselco, a subsidiary of the British Petroleum Co., is based in Denver, CO. The company is mine operator and jointly owns the project with Nerco Minerals Inc., a wholly-owned subsidiary of Pacific Power and Light. Alligator Ridge is Amselco's first US mining operation. Geology Alligator Ridge, so named because it appears in outline to be an alligator at rest, contains disseminated micron gold embedded in iron-streaked siltstones. Although definitive conclusions have not been drawn on age and origin, the gold ore bodies are probably young by geological standards. They were formed in a recent volcanic period still evidenced in parts of Nevada by geysers and hot springs. As these superheated solutions rose through the permeable siltstones, they deposited minerals in the rock and formed the present gold ore bodies. During 1977, an extensive soil geochemical sampling program with additional geologic mapping and outcrop sampling were conducted. The results generated several drill targets. Initial drilling was performed in November and December 1977, and ore grade mineralization was encountered in the first drill hole. The Alligator Ridge mine is unusual in relation to other and more recent western US mineral discoveries in that it occupies an area that had no previous mining history. The ore deposits are hosted in upper Paleozoic sedimentary rocks that consist predominantly of a thick carbonate sequence. The main ore host is the Devonian-Mississippian Pilot shale, which occurs locally as a sequence of thin bedded calcareous, carbonaceous siltstones and claystones. The maximum observed thickness of the Pilot section in the mine area is about 140 m (460 ft). Rocks in the Alligator Ridge area have been folded into a series of low amplitude anticlines and synclines that strike north-south and plunge to the south at about 20°, with limbs that dip nearly 20°. The folds have been truncated and deformed by later high-angle faults that generally strike northwest. Although multiple stages of movement are evident on the fault systems, the youngest period of activity is along the major northeast trend. The predominant structural pattern in the area is of the basin- and range-type high angle normal faults. Alligator Ridge is actually a horst block between two basin and range faults. Vantage Ore Deposits There are three principal ore deposits within the Vantage Basin and several smaller satellite mineralized areas. The three Vantage deposits are encompassed in a mineralized zone that covers an area 915 m (3,000 ft) long and 305 m (1,000 ft) wide. All mineralized zones have been outlined by more than 600 rotary drill holes, with an average depth of 150 m (500 ft). Mineralization occurs in both carbonaceous and oxidized rocks. The carbonaceous gold-bearing material is not amenable to current heap leaching practice. Therefore, only oxidized ores are now treated. The carbonaceous gold-bearing material is segregated and stockpiled as it is encountered during mining. The three ore bodies occur along a north-northeast strike, with mineralization becoming progressively deeper from north to south. The ore block dimen-

Jan 6, 1984