Search Documents

By Lawrence L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P2O5 is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pet P2O5 and a P2O5 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1982

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016

By Mojtaba Ahmadiantehrani

A previous study showed that up to 80% gold extraction could be obtained with 160 lbs/ton hypochlorite consumption at ambient temperature from a low grade Carlin-type carbonaceous ore. Crushing the ore to a finer size and agglomerating with cement decreases hypochlorite consumption by 60%; while, agglomeration and curing the cement-ore mixture with hypochlorite solution has no significant effect on total gold extraction. The high hypochlorite consumption is due to oxygen depletion as the solution percolates through the column, i.e., oxidation of gangue materials. These side reactions are reduced at sub-ambient temperatures resulting in a substantial further decrease in hypochlorite consumption. The optimum temperature range and additional reduction of hypochlorite consumption by introducing the reagent into the column at different elevations will be discussed.

Jan 1, 1992

By J. Fraser Forbes

"The meaning of the term ""process control"" has evolved significantly since its widespread use began in the manufacturing industries in the 1940s. Further, the scope of process control applications has drastically increased both in terms of the breadth of industries using process automation technologies and the vertical integration of these technologies within a single industry. This evolution and integration of process control technologies within the manufacturing industries has proceeded to such an extent that process automation is an integral part of modern business practices.This paper will examine the current status of process control technology from simple process regulation through process performance optimization to business planning. Each layer of the operations automation hierarchy will be discussed both in. terms of the current state-of-the-art and the directions in which these technologies are evolving. The key tools and tasks necessary for success at every level of the automation hierarchy will be introduced. Finally, the critical challenges that must be faced in accomplishing the goal of complete Computer Integrated Manufacturing (CIM) will be described.Finally, although this paper addresses issues of practical importance to any manufacturing company, the discussions will be framed in terms of the particular challenges facing and the opportunities available within the materials manufacturing industries."

Jan 1, 2000

By W. G. Davenport

This chapter demonstrates how our matrices can be used for controlling a flash furnace. Specifically, it shows how we can determine the adjustments in industrial oxygen, air, oil and flux input rates that will; (a) correctly alter product temperatures and compositions to newly targeted values (b), maintain set-point product temperatures and compositions with varying feed compositions and feed rates. It also discusses corrective actions that might be taken when furnace temperature and matte grade unexpectedly change.

Jan 1, 2001

By Gopalakrishna M. Rao

"Several industrial and government laboratories are of the opinion that solar--cell technology will grow into a billion-dollar industry by the year 2000, especially if oil prices rise again. Of the variety of materials that have been investigated as the major component of photovoltaic systems, silicon appears to have an outstanding advantage. The cost factor is the primary importance in photovoltaic development, since the technology to make silicon cells of acceptable efficiency and life time has existed since the early stage of the space program. Electrometallurgy is one of the low--cost processes for the production of silicon, since it allows direct, single-stage production from some abundant, inexpensive source materials such as silica and fluorosilicates. Among several systems, two are given particular attention, using inorganic baths with Si0 2 or K2SiF6 as the source of silicon respectively. They appear capable of development to commercial production. Conceptual designs of a commercial--scale cell for silicon production at temperatures above its melting point, and of a pilot' plant for plating silicon from an all-fluoride bath are presented. Energy ProspectsThe major changes in the world energy since the first energy crisis in 1970 have impacted on our community. When oil was $40 a barrel in the mid-1970s, we became obsessed with the energy conservation and a search for alternate energies. Even though the crude oil fell below $15 a barrel during the last several years, our energy security fears continue to haunt us. This time it is not the scarcity, but the abundance of foreign oil and the decline in the domestic production.The prospects of energy depends on the demand and supply of energy. These, in turn, depend on future energy prices, which are linked to economic factors, political events, and unforeseen circumstances. Although no one can predict the future with certainty, three energy consumption patterns used by the Ford Foundation are as shown in Fig. 1."

Jan 1, 1988

By M Phil Schwarz

"A CFD model for the gas-side of an impinging jet iron bath reactor has been developed to assist in the interpretation and design of oxidizing gas-melt reaction rate experiments. Heat transfer and reaction at the surface have been included. A free surface model, which solves for the liquid motion within the bath as well as the gas motion above the bath, has also been developed. This model also predicts extent and shape of the dimple formed on the liquid surface by the impinging jet. Both models have been run for conditions typical of jet impingement experiments using CO2 , H2O and O2• The main conclusions are• Results from the model for gas-side mass transport are in good agreement with the empirical correlation of Belton and Belton (1980)• Experimentally determined rates of decarburization by CO2 should be corrected for mass transfer because the experiments are often carried out under mixed rate control, eg for gas flow rate 10 L/min when the sulphur concentration is lower than 0.045• If the rate constant for oxygen reaction is greater than about 5 mol/m2.s.atm, it cannot be determined using a gas flow rate of 10 L/min or lower because of mass transfer control.• A cavity of depth 4.5 mm is predicted for a gas flow rate of 10 L/min and this substantially changes the flow field (and hence reaction rate) compared with a simulation in which the surface is assumed to be flat."

Jan 1, 1999

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

The effect of change in slag composition upon metal losses to the slag and the relationship between slag composition and slag matte separation was investigated at 1400°C. The synthetic slags containing CaO, MgO, SiO2,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Precious Group Metals) from the Merensky Reef of South Africa. The matte with a grade of 9.3% Cu and 16.0% Ni was a typical electric furnace product. The results indicated that the Cu and Ni solubility in the slag increases with the increase of the basicity ratio and CaO and MgO contents of the slag. At constant CaO/MgO ratios the rise in basicity decreases the metal losses. When FeO and SiO2 contents of the slag are kept constant, the substitution of MgO with CaO decreases the metal losses. The relationship between slag composition and matte-slag separation was found to depend primarily on the basicity ratio and the FeO content of the slag. The net effect comes from a strong interaction of the two in such a way that increasing basicity and decreasing FeO contents deteriorate the clean separation of the two phases.

Jan 1, 1994

By Jagdish C. Agarwal

Although copper ranks very low in the order of abundance of elements in the crust of the earth, it has been one of the first metals utilized by mar, at his emergence from the Stone Age, about 10,000 years ago. Use of copper for weapons, tools, utensils and ornaments dates back to the twilight of history, 6,000-5,000 B.C. Native copper outcrops and the malleability of the metal explain its very early use by the cave-dwellers. The working, melting and extraction of copper from its minerals are among the oldest metallurgical achievements of the human race. The oldest complete smelting installations for the extraction of copper from its minerals, dated about the fourth millenium B.C., were recently discovered in the Timna Valley, Wadi Arabah, Israel. (1) The history of the developments of the extractive metallurgy of copper has been adequately reviewed recently. (2,3) The center of copper production migrated from the Eastern Mediterranean to Northern Europe (Mansfeld, Germany, Swansea, Wales) towards the end of the Middle Ages (1500 A.D.). The production of the metal was boosted tremendously in North America since the end of the nineteenth century (Fig. 1).

Jan 1, 1976

By J. Y. Hwang

Microwave heating is an attractive alternative to conventional heating methods because heat is generated directly within the microwave absorbing materials. It has potential to be utilized for selective heating and removal of specified components from a materials mixture. This investigation was undertaken to explore the potential of selective heating and burning of binders for foundry sand reclamation. Selected raw materials and binders used in foundry operations were tested to determine their receptivity to microwave heating. Time needed to reach 600°C and/or the maximum temperature achieved for samples irradiated by microwaves for twenty minutes under 800 W microwave power are reported. The microwave heating characteristics of the selected materials are summarized and discussed. The interactions between microwaves and the raw materials used in a foundry. such as silica sand. chromite sand and bentonite (clay) binder were studied. The results showed that chromite sand coupled well with microwave energy at ambient temperature while silica sand did not. This was expected because the major component of chromite sand. iron chromite (FeCr2O4). is a good microwave absorber. while quartz, which is the major component of silica sand, is a microwave transparent material at ambient temperature. Bentonite absorbs microwaves well because it contains a hydroxyl functional group and water molecules in its structure. It was found that the structure of bentonite was changed through microwave irradiation. Microwave heating characteristics of silica sand mixed with different amounts of bentonite binders were investigated. The presence of bentonite in the mixture improved the microwave heating of silica sand significantly. and bentonite was deactivated by the microwave processing.

Jan 1, 1995

By H. L. Fraser

A review of the possibilities of performing microchemical analysis in thin sections using a combination of scanning transmission electron microscopy and energy dispersive spectroscopy of x-rays is given. Particular attention is paid to the factors that limit accurate analysis at the highest spatial resolution. As an example of the use of these techniques applied to a potential problem in minerals processing, the identification of iron pyrite and pyrrhotite particles in Illinois, Herrin #6 coal is presented.

Jan 1, 1981

By A. J. Maselli, E. C. Cemak

Hartford Steel Technologies (HST) has a pyrometallurgical and hydrometaliurgical process capable of reclaiming valuable metals from a hazardous waste· stream such as EAF Dust. The HST Process effectively addresses the growing environmental concerns surrounding the increasing production of EAF Dust without producing any hazardous waste material as byproducts. Currently EAF Dust production levels are exceeding the 1,000,000 metric tons per year mark. The HST Process is designed to separate iron, zinc, lead, cadmium, copper, and silver metals using a two-phased process. The Pyrometallurgical side of the Process utilizes a Rotary Hearth Furnace to separate the iron metal from the remaining metals. These remaining metals are further separated, using a Hydrometallurgical Process, in a series of digestion tanks. The individual metals are then collected in saleable form.

Jan 1, 2000

By S. E. Khalafalla

A method for preparing ferrochromium alloys containing less than 2 pct carbon has been devised in a single vacuum furnace reactor. This method can conserve chromium and should reduce the capital and energy requirements relative to chromite electrothermal reduction. Reduced products containing less than 2 and as low as 0.01 wt pct carbon were obtained by reacting pellets of chromite and carbonaceous reductant mixtures at pressures of 0.1 to 1 ton and temperatures of 1,230° to 1,320° C. The extent of reduction increased with increased temperature and decreased pressure; however, operating conditions were limited due to the onset of significant chromium vaporization at higher temperatures and lower pressures. Foundry coke, anthracite, and carbon black were found to be superior to graphite as reductants. The reduction of chromite to metallics was found to proceed via the carbide intermediates Fe3C or Cr3C2. Lime accelerates the. rate of solid state reduction of chromite and can shorten the furnacin1r time at 1,3000 C under vacuum from 13 hours to less than three hours. Additional lime and silica are added to the hot reduced chromite after releasing the vacuum and raising the furnace. temperature to 1, 700° C. Soaking the charge for about 20 minutes gave a button of low carbon ferrochromium alloy beneath a well-defined slag layer.

Jan 1, 1985

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. The effects of feed matte grade, matte particle size, oxygen-to-matte mass ratio, oxygen content of the process gas and temperature on the particle oxidation rate, quality of conversion, particle size change and particle morphology were determined. The converting quality was highest (~68) with the 58% copper matte at 1100°C. At similar conditions, the 72% copper matte was more likely to produce copper oxides and leave unoxidized particles rather than directly produce sulfur dioxide at 1100°C, resulting in an average converting quality of 55. The quality of conversion was poorest for the 72% matte at 920°C (~45); the sulfur removal was extremely low even with a relatively high degree of oxidation. Fragmentation of the particles was significant in all cases with the 72% matte. A higher O2/matte .ratio and higher temperature, in general, resulted in increased fragmentation while oxygen enrichment had no significant effect. With the 58% matte, particle size was found to increase for the finest fractions rather than to decrease due to particle expansion.

Jan 1, 1998

By J. W. Lyman

Nickel-metal hydride (Ni-MH) battery electrodes have been developed as a substitute for cadmium-containing negative electrodes. Use of Ni-MH electrodes offers enhanced electrochemical properties in many instances as well as reduced environmental toxicity. Rechargeable batteries using Ni-MH electrodes are also strong candidates for electric vehicles. During the production and secondary reclamation of these battery types, recycling procedures will be needed to prevent environmental impact caused by these wastes as well as to recover the value inherent in the scrap. The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical technology that separates and recovers purified metallic components from Ni-MH battery scrap of two types, AB, and AB,. An investigation of acid dissolution and metal recovery techniques has determined several processing alternatives that may be used to promote the successful recycling of much of the battery fabrication scrap and eventual secondary scrap. Although recovery techniques have been identified in principal, their applicability to mixed battery waste stream and economic attractiveness remain to be demonstrated.

Jan 1, 1995

By I. Ohnaka

Although many works have been reported on the semisolid casting, the mold filling behavior of semi-solid alloys has not been so well understood. This paper compares the physical and numerical simulation results on the mold filling behavior. Physical simulation was performed by using solid-water mixture. The numerical simulation was made under the assumption of one phase flow with an effective viscosity. It was found that the solid particles stabilize the flow greatly if the kaction solid exceeds about 0.4, because viscosity increases greatly. The overall flow behavior can be estimated by the numerical simulation. Interesting flow behavior was also found which can not be observed in the case of one phase flow and which is difficult to simulate by the one phase flow assumption.

Jan 1, 1997

By L. Klinger, T. Werber, LA Levin, A Katsman

"The process of catastrophic carburization known as ""metal dusting"", whereby a solid metallic material is converted into fine particles in a carburizing atmosphere, was analyzed. It was shown that this conversion is the result of plastic deformation and subsequent fracture accompanying diffusional phase formation in the near-surface layer. The process is controlled by internal stresses arising during phase transformation. Competition between stress generation and relaxation may result in the attaining the ultimate strength in the near-surface layer and its fracture. Such a mechanism of metal disintegration may occur in a certain temperature interval depending on the kinetic and geometrical parameters of the system - the diffusivities of the alloy's components, the ratio between specific volumes of the new and the old phases, and the ultimate plastic strain. The temperature interval for disintegration of carbon steel, the rate of disintegration, and the period of the disintegration cycle, were evaluated and compared with experimental data. IntroductionCatastrophic carburization, known as ""metal dusting"", consists in conversion of a solid metallic material into fine particles. The process occurs in a carburizing atmosphere at elevated temperatures. The corrosion product, usually named ""coke"", consists of metallic particles dispersed in a loose carbon matrix. Under industrial conditions metal dusting takes place, for example, in a gas mixture of CO and H2 or in hydrocarbon environments. Steels, nickel- and cobalt alloys are susceptible to this kind of wastage in the temperature range 400-800°.A mechanism of metal dusting in steels was proposed by Hochman [1] and later developed by Grabke and coworkers [2-5]. According to the proposed model, the process consists of the following reaction steps:"

Jan 1, 1996

By P. M. Swash

The paper describes the use of mineralogical methods in the exploration and evaluation of primary diamond occurrences. The most common methods that are used include the systematic search for kimberlitic indicator minerals, surface textural study of the indicator minerals, (garnet, spinel, ilmenite and chrome diopside) and alluvial macrodiamond studies so as to understand their provenance and guide exploration towards diamondiferous targets. The mineral chemistry of the indicator is used to positively assess the origin of the mineral grains and is also pivotal in the determination of the diamond potential of a deposit. Petrography of the primary deposit is able to identify the body to be kimberlitic and is also a support to the mineral chemistry findings. Unambiguous proof of a prospects potential to contain macrodiamond is proven by the occurrence of microdiamonds in the residues from the rock. The presence of a sufficient number of microdiamonds in the rock is enough to determine a semiquantitative grade estimate and warrant further metallurgical evaluation so as to determine its actual macrodiamond content.

Jan 1, 1991

By J. E. Clemson

The Black Pine sediment-hosted, disseminated gold deposit is located in Cassia County, Idaho. Gold mineralization occurs in flat-lying zones 50 to 100 feet thick. Total geological ore reserves are 5.6 million tons grading 0.049 oz/t. Ore types include: non-carbonaceous, oxidized ore; carbonaceous, sulfide ore; and carbonaceous, partly oxidized ore. In the oxidized ores, native gold grains commonly occur in porous hematite pseudomorphs that have replaced disseminated framboidal and euhedral pyrite, and this gold should be readily leached by cyanide solutions. Approximately 4 % of the native gold observed in the oxidized ores is locked within gangue and may be refractory to cyanide solutions. Native gold has not been observed in the unoxidized samples, all of which are characterized by primary sulfides. It is suspected that the bulk of the gold mineralization in the sulfide ore occurs as submicroscopic particles within pyrite and will be refractory to cyanidation. It is believed that much or all of the gold observed in the oxidized samples was originally in pyrite but was released and re-precipitated during oxidation. The degree of oxidation of the pyrite and the presence/absence of preg-robbing carbonaceous material is used as a guide in delimiting zones of mineralization amenable to heap leaching.

Jan 1, 1988