Search Documents

By Sung-Mo Jung

Experiments were carried out on a system with artificially prepared slags in a graphite crucible, in order to examine the possibility of recycling BOF slags produced in the steelmaking process. More than 80% of FeO and P2O5 was reduced within 20 minutes and the FeO reduction rate was greater than that of P2O5. P2O5 reduction began after more than 60% of FeO was reduced. Increasing slag basicity enhanced the reduction of FeO and P2O5. Temperature also improved slag reduction. The overall reduction rate was controlled by the chemical reaction at the slag/carbon interface. The reduction rates of FeO and P2O5 were second and first order with respect to their respective contents. Most of the reduced phosphorous is believed to vaporize in the form of P2 gas.

Jan 1, 2006

By Guo Xian Jian

In this paper, the gas composition calculations on the FeS-H20 system at elevated temperature were performed. The results show that the gas constituents are H20, S02, H2S, Sj, H2, and O2 and the order of the compositions partial pressure is PH2o> PH2 >PSO2 >PSj >PH2S >PO2 when FeS is oxidized into Fe304 and FeO by steam in the temperature of 700°C -960°C, the Claus process occurs with the decrease of gas temperature in the off-gas and the S02 and H2S in the gas are transformed into Sj , the critical temperature for the transformation is 600°C, and conversion percent of Sj is 97% at 330°C,

Jan 1, 1996

By Yiming Rong, Gang Wang

"Water quenching is one of common heat treatment processes but with complex physical phenomenon, in which vaporizing, bubbling and convection are involved. The general simulation of liquid quenching processes is conducted by using temperature dependent value of heat transfer coefficient (HTC) obtained from experimental measurement under a strong assumption. A preliminary multiphase flow model developed by using Ansys-CFX for water quenching has been presented in this paper, which shows a distributed HTC with a time dependent feature. The conjugate heat transfer is used to describe thermal conduction in the simplified workpiece, and generation, growth and flow of bubbles are modeled by using Eulerian-Eulerian method for the gas-liquid multiphase flow. The simulation result shows the intense variation of heat exchange through the interface between workpiece and liquid, and the unsteady distribution around the solid surface.IntroductionQuenching is a rapid cooling process which makes the desired solid phase transformations happen for the certain material properties. For aluminum alloy, rapid quenching will prevent all phase transformation and generate a supersaturated single phase."

Jan 1, 2012

By Fuqiang Zheng, Shuai Wang, Ting Duan, Yufeng Guo, Tao Jiang, Andrew Yakovlevich Travyanov

Organic compound binder can effectively enhance the strength of green pellet and reduce the addition amount of binder during pelletizing. However, compared with traditional bentonite binder pellet, the compressive strength of the preheated and roasted pellets significantly declined. It is of significance to resolve this problem for the application of organic compound binder. In this paper, magnetite concentrate was used as raw material, carboxymethyl cellulose (CMC)- bentonite compound was used as binder, characteristics of preheated and roasted pellets and the effects of additives on that were systematically studied, The results show that sodium acetate can effectively improve the characteristics of the finished compound binder pellets. The compressive strength of the preheated and roasted pellets were increased by 52/N·p-1 and 342/N·p-1 respectively when the addition amount of sodium acetate is 2.2%wt of compound binder. Moreover, sodium acetate has no adverse effect on pelletizing process and drying characteristics of green balls.

Jan 1, 2015

By Susumu Nagae, Hajime Ikeda

Recently, a number of mine development projects have been setback by social, economic and, environmental circumstances that had not been seen before. Many of these problems do not always originate from direct mine pollution. Typical examples of these are· conflicts between the exploration company and the local residents, sudden objections just before the development is to begin, and unexpected tightening of environmental regulations. The common background to these problems is expanding global environmental awareness. This includes complex factors ·such as the expansion of exploration to remote regions, the brisk activities of environmental NGOs, the increase of international environmental laws and, governmental policy changes. Today, the range of issues concerning mine development is widening significantly. The participation of local residents arid NGOs in the development planning, together with the company and government, has become essential for smoothly carrying out mine projects and making them more beneficial for stakeholders. Introduction The common image of the environmental problem with respect to mining is direct mine pollution, such as the collapse of tailings dams, pollution from refineries, and acid mine drainage. All over the world, the mining industry has made large investments in capital and technology to solve and prevent mine pollution, and these efforts have been making steady achievements. However in recent years, new cypes of environmental problems which are not originating directly from mine pollution are emerging frequently. Most of the problems are concentrated at the exploration stage to early stage of development, which have less impact on the environment. In the worst case, mining project may be forced to cancel and could cause serious damage to the industry because they could not collect their investment. I would like to take a general view of the examples of new types of trouble, their characters, background, and strategies against these problems.

Jan 1, 2000

By S-L. Jämsä-Jounela

Fault diagnosis systems have attracted growing interest in a number of engineering fields. The number of applications has increased and successful results have been widely reported. The fault diagnosis system presented in this paper is integrated, and it monitors the states of the process and performs fault detection and diagnosis on the process equipment. The monitoring of process states is carried out by means of Kohonen Self-Organising Maps that is a powerful tool in visualisation and analysis of high dimensional data in engineering applications. This paper presents the results of SOM analysis carried out on the Outokumpu flash smelting process. The subsystems analyzed in more detail are the condition of the concentrate burner, the condition of the gas line on the basis of the pressure distribution in the process and the cooling water circulation of the waste heat boiler, and the condition of the furnace and furnace equipment on the basis of the temperature distribution in the furnace and gas line. Keywords: Fault diagnosis, Process monitoring, Kohonen Self-Organising Maps, flash smelting

Jan 1, 2001

By Mark Cross, Diane McBride, Nick Croft

Extractive metallurgical processes rate amongst the most complex from the perspective of computational modeling. They typically involve multi-phase and multi-component fluid flow in very complex geometries, heat transfer driven by a number of interacting phenomena, solidliquid- gaseous phase change and mass transfer together with complex thermodynamics and associated chemical reactions. Beyond the model building itself, key challenges have always involved being able to identify the phenomena present together with interactions to characterize processes and experimental laboratory and plant data to parameterize the arising models – it is in this milieu, which require considerable process understanding and subtlety of thought, that David Robertson has made his contributions. We will review the achievements, over the last couple of decades, in computational modeling of extractive metallurgical processes and address some of the remaining challenges to enable simulation based process design, as we move through the 21st century.

Jan 1, 2014

By Taegong Ryu

The thermal plasma process has been applied to the preparation of nanosized tungsten carbide (WC1-x). The reduction and carburization of the vaporized chloride by methane-hydrogen mixtures produced nanosized WC1-x powder, with a small amount of WC or W2C phase. The products were characterized using XRD, carbon analyzer, and TEM. The effects of plasma torch power, the flow rate of primary plasma gas (Ar) to generate plasma flame, and the addition of secondary plasma gas (H2) on the product composition were investigated. The tungsten carbide (WC1-x) powder had a particle size less than 30 nm. The powder was treated under hydrogen atmosphere to fully carburize the WC1-x, and W2C phases to WC as well as remove excess carbon in the product. Finally, WC powder with a grain size less than 40 nm was obtained.

Jan 1, 2008

By M. H. Staia

A Venezuelan ilmenite concentrate has been chlorinated at a temperature of 700" C by carbon tetrachloride. In the experimental rig, built at laboratory level, the direct chlorination process yielded a TiCI, recovery of approximately 85% after 280 minutes processing. The partial pressure of carbon tetrachloride was nearly atmospheric (0.94 atm). Product vapors from the reactor were fractionally condensed in a condenser which was maintained at a temperature of 250°C meanwhile TiCl, vapors were condensed in refrigerated coils at a temperature of -20°C. The concentrate used in this investigation was obtained by applying gravitational and magnetic concentration methods to the black sands. The experimental results have shown the need to asses the influence of the weight ratio of ilmenite to carbon tetrachloride on the resultant products. The equilibrium of the heterogeneous system has been calculated taking into account the initial experimental conditions.

Jan 1, 1995

By Nickolas J. Themelis

Nearly thirty two million tons of municipal solid wastes (MSW) are combusted annually in over one hundred U.S. Waste-to-Energy (WTE) power plants, thus reducing the use of fuel oil by about 1.6 billion gallons of fuel oil One of the advanced WTE processes is the 0.9-million ton/y SEMASS facility at Rochester, Mass. Most of the combustion in the three giant combustion chambers occurs while the injected shredded wastes are in suspension, i.e., in flash combustion mode. The velocity, temperature, and concentration profiles in the SEMASS combustion chamber were simulated by representing the combustible fraction of MSW by the simplified formula C6HIO04 and using the CFD program Fluent to solve the turbulent energy and mass transport equations. After validation against plant data, this model will be used to examine options for increasing the productivity of WTE combustion chambers, such as optimum distribution of primary and secondary air and oxygen enrichment.

Jan 1, 2003

By Roger Altman

The solubility of copper in primary spinel crystals encountered in reverberatory slag samples has been determined by electron microprobe analysis. These spinels, which ranged in composition from 22% A12O3 to pure magnetite, contained small quantities of dissolved copper (0-0.4%). Based on literature data it was estimated that the solubility limit of copper in solid magnetite is no greater than about 1% at 1200°C and about 2% at 1250°C. However, it was found that practically every spinel crystal examined contained significant amounts of matte inclusions. Further examination of converter slag revealed large quantities of irregularly shaped precipitated magnetite crystals which contained a large proportion of copper inclusions. Additional experimentation showed that the total copper content in reverberatory slag samples was greater than the sum of the estimated en- trained plus dissolved matte in the slag. This difference is believed to be significant and is due to the presence of matte inclusions in the spinel crystals. In the present reverberatory slag samples these inclusions accounted for about 1/2 of the amount of sulfide directly entrained in the slag.

Jan 1, 1976

By S. P. Rivers

The stainless steel industry re1ies on nitric-hydrofluoric acid (HNO,/HF) pickling solutions to remove surface contaminants and maintain the corrosion resistance of the steel. More stringent environmental guide1ines are expected to be placed on the disposal of these solutions which could significantly increase processing costs. The U.S. Bureau of Mines has been conducting research to develop a process for recycling depleted pickling solutions, thus reducing the quantity of by product acids generated. Research has shown that F- can be liberated from the predominant iron fluoride species (FeF,') by using oxalic acid in an electrodialysis cell. Ion selective membranes allow dissolved metals in the depleted solution to be replaced with hydronium ions by metathesis, thereby regenerating the HF. The regenerated HN03/HF is then retained in the pick1ing solution. This paper reports on the research effort at the U.S. Bureau of Mines Rolla Research Center to apply electrodialytic recycling to HN03/HF pickling solutions.

Jan 1, 1993

By S. L. Pohlman

Physical characteristics of possible importance in the acid leaching of Chrysocolla have been evaluated. Surface area studies and pore size distribution indicate: 1) a large surface area (350 m /gm); 2) an average pore size of 13 or 16 Å , depending upon use of the adsorption, or desorption, branch of the Type IV isotherm in the evaluation; ) the presence of a significant fraction of pores of size less than 15 Å determined by the accumulation surface area method. The initial structure is micro- crystalline on the basis of x-ray powder patterns; the silica leach residue is amorphous and has only 24 m2 /gm surface area, and loses integrity when dry. However, readsorption of copper onto the wet leach residue gives a product with integrity and 100 m2 /gm surface area. Visual observation of the leach residues supports evidence of a non-protective diffusion mechanism of leaching which is well correlated by the shrinking core model previously presented.

Jan 1, 1976

By Sylwia Zymankowska-Kumon, Rafal Danko, Józef Danko, Mariusz Holtzer

"Burning of ceramic materials is carried out at temperatures 900+ 1300°C, in dependence of the required functional properties. The Faculty of Foundry Engineering together with the Faculty of Material Engineering and Ceramics developed the technology of production of burned ceramic materials with using spent moulding and core sands. The mentioned above waste materials of the foundry industry fulfilled -in plastic masses intended for obtaining ceramic materials -the role of the addition weakening clay raw materials. The laboratory investigations were fully verified by the results of industrial tests. It should be pointed out that none negative effects were observed at the stage of mixing raw materials and preparation of plastic masses. The measurements of exhaust gases emissions performed during burning the products containing spent moulding sands as well as during the normal production did not exhibit any significant differences, which could have indicated the harmful impact on the natural environment.IntroductionSands are used by the foundry industry to make metal casting molds and are a mixture of silica sand, bentonite clay and carbonaceous additives or resins. During the casting process, the molten metal cause thermal decomposition of carbonaceous additives or resins, which results in the formation of potentially hazardous organics, that are emitted to the atmosphere and condense in the molding sand. Each year the U.S. foundry industry landfills about 10 million tones of sand because it is no longer suitable to make metal casting molds. A large high-silica sand content in spent foundry sands (SFSs) generates rational premises for their reuse in other than foundry practice fields. Efforts to divert the SFSs from landfills and encourage their beneficial use in manufactured soils, geotechnical applications, the construction industry (road construction, highway construction), the building materials industry (cement, bricks, limestone manufacture), in the filling of mining cavities or in landfill construction (roads on landfills, permanent covers) are make [1-7]."

Jan 1, 2013

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By Sepp Härkki

The energy crisis in Finland after World War I1 together with a sharp rise in the price of energy caused Outokumpu Oy to consider replacing the electric furnace smelting of copper concentrates by some other method. The flash smelting method developed under these circumstances offered a considerable saving of fuel through the utilization of the reaction heat of sulphides and yielded a high recovery of sulphur in the form of acid. The pilot plant testing of the new process was carried out in the years 1947 - 1948. The process was adopted for the smelting of copper concentrates (1) (2) (3) on a commercial scale in 1949 and applied successfullv to the smelting of -nickel concentrates' at the Harjavalta Works in 1959 (4) (5) (6). In 1962 Outokumpu adopted another type of flash smelting where elemental sulphur is recovered from the gases after the thermal decomposition of pyrite in the flash smelting furnace (7) (8): In recent years, the copper-nickel flash smelter and pyrite process have been combined to produce elemental sulphur instead of SO2 from the smelter gases (9) (10). The basic idea of the Outokumpu flash smelting process for sulphidic ores is that the conventional methods with separate roasting and smelting operations are replaced by a combined roasting, smelting and part-converting process carried out in one unit. The heat generated from the exothermic reactions can thus be used for smelting the ore so that only a small amount of additional fuel is needed. The characteristic of the method is also that the dried, fine-grained concentrate is smelted in suspension, which offers the best conditions for rapid reactions. The recovery of waste heat from the furnace off-gases had been considered already in the original flash smelting system. A

Jan 1, 1976

By A. G. Cecutti

A brief overview of the known significant health effects of both Nickel and Cobalt will be presented. Some time will be given to the current research activities, especially for Nickel. Emphasis will be placed on some of the controversial issues associated with their health effects.

Jan 1, 1988

By Don Ibana

The use of solvent extraction (SX) in process metallurgy is particularly attractive as it is applicable to a wide range of solute concentration and pH, and it allows complete separation of chemically similar metals such as nickel and cobalt and the rare earths among others. It is therefore applicable to the processing of low grade and complex ores, which is increasing and expanding owing to the diminishing reserves of quality ores, and this has driven the increasing and expanding use of SX.The current SX technology, however, has inherent limitations owing to the use of mechanical agitation as it induces high shear mixing. Excessive shear produces very fine droplets, and while this favours mass transfer, it also leads to sluggish phase separation. High shear mixing is also known to favour crud formation. All these factors as well as high power and reagents consumptions contribute to poor process efficiency. Electrostatic solvent extraction (ESX) is similar to conventional SX except that mechanical agitation is replaced with electrostatic agitation. In direct contrast to mechanical agitation, it allows the production of very small droplets that can be made to maintain intense motion, which favours mass transfer, without affecting the phase separation. In addition, as it uses an electrostatic field, the power consumption is minimal. Hence, it promises to be a superior alternative to conventional SX mixing although an application of the technique is yet to be achieved.Our work to develop an application of the technique in process metallurgy has now established that electrostatic field has no effect on either the stability of the reagents or the chemistry of the process. A volumetric flowrate that is comparable to that of a conventional sieve plate pulse column is achievable. We have also established that electrostatic fields can be made to yield much narrower droplet size distributions than those of mechanically agitated contactors, and they allow better control of droplet motions, which include oscillation and linear motion and hence, mass transfer. These are significant advancements toward our goal and shall be discussed in this presentation.

By Krishna Parameswaran

This paper illustrates sustainability considerations in copper hydrometallurgy using examples of practices at ASARCO LLC, an integrated U.S. primary copper producer. Using the classic Brundtland Commission development of sustainable development, i.e., “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper discusses how copper hydrometallurgical processes can be sustainable. The examples used to illustrate sustainable development and related concepts include: water conservation opportunities in milling and leaching operations; implementing green chemistry and promoting product stewardship in the electrorefining of copper.

By Shigeatsu Nakazawa

Activities of Bi and In in the Bi-In liquid alloy were measured over the whole range of composition at the temperatures from 850K to 1050K. An alloy was vacuum-sealed in a quartz cell and heated at the temperature of interest. The absorption for 307nm radiation from Bi lamp was measured for Bi atom vapor in the cell. By heating a pure metal as a standard and measuring the absorbance as a function of the temperature, an analytical curve for Bi atom vapor was constructed and used for conversion of the absorbance to the vapor density. Bi activity was determined as the ratio of the Bi atom vapor density over the alloy to that over a pure metal. The same procedure was applied to the In 304nm radiation from In lamp and In activity was determined independently of Bi. Results showed that the liquid Bi-In system behaves like a regular solution.

Jan 1, 2003