Search Documents

By D. L. Jones

The leaching of natural chalcopyrite was studied in both ferric sulfate and ferric chloride solutions. The chemistry of the two reactions is quite different, with substantial sulfur oxidation occurring only in sulfate solutions. Ferric chloride is a more effective reagent, for the leaching rate is greatly increased with finer particles and higher (Fe+++), and unaffected by high (Fe++); none of these advantages are found with ferric sulfate. In addition, the morphology of leaching appears to be different, with ferric sulfate leaching preferentially along fissures or grain boundaries. The kinetics were found to be linear over an extended period, rather than parabolic as reported elsewhere. An explanation of the observed phenanena is proposed using the electrochemical theory of leaching, and experimental measurement of the mixed potential of the mineral during leaching.

Jan 1, 1976

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By Robin M. Forbes. Jones, Suhas V. Patankar, Ramesh S. Minisandram, Jr. Carter, Kanchan M. Kelkar

"The nucleated casting process currently under development has the potential for production of Ni-base superalloy preforms that possess superior microstructure to product made by conventional casting processes, primarily for gas turbine applications. In this process, electroslag remelted (ESR) clean (i.e., free of ceramic inclusions) molten metal is conveyed via a watercooled copper Cold-walled Induction Guide (CIG) to a gas atomizer. The spray of clean metal droplets is then directly cast into a water-cooled crucible for ingot production. The microstructure of the resulting ingot preform evolves within the length scale of the individual droplets and is a function of the thermal state of the incoming metal droplets. This, in turn, depends on particle size, flight time and heat exchange with the gas phase.In the present study, computational models is developed for the analysis of the flow and heat transfer in the gas-metal spray system under axisymmetric and steady-state conditions. The gasphase flow is analyzed using an Eulerian framework and turbulent mixing within the gas phase is modeled using the two-equation k-e model. The dynamics of the metal particles is analyzed using a Lagrangian framework that involves calculation of the trajectories of the metal droplets. A two-way coupling is considered whereby the transport and heat transfer in the gas and the metal phases influence each other.The analysis is developed at two levels. The spray model performs a detailed calculation of the spray dynamics in the vicinity of the spray and is intended for predicting the temperature and mass flux distributions of the metal spray depositing into the mold. The chamber model enables prediction of gas flow and motion of metal particles in the entire spray chamber."

Jan 1, 2004

By J. J. Kim

In a study of buildup in a green-feed reverberatory furnace, it was determined that approximately half of the crucible area has a moderate buildup of 25 in. or less, and that the area extending 45 f t from the burner end of the furnace has only a slight buildup. The false bottom, averaging 6 in. in thickness, was found to cover the entire crucible area. The stratification of Cr2O3, A12O3, and SiO2 occurs throughout the slag layer; this phenomenon is the principal reason for the formation of the false bottom in the green-feed reverberatory furnace. The false bottom is caused primarily by the settling of FeO*(A1,Cr),03 aggregates, which are derived mainly from returned converter slag. The false bottom can be transformed to a solid permanent buildup in the furnace, particularly when the matte is completely withdrawn. From the material balance of Al2O3 and Cr2O3 around the furnace, It is estimated that the average rate of aluminum chromite accumulation is approximately 0.3 ton per day or less.

Jan 1, 1976

By Rod Samuels, Rupert Allen, Thomas Harper

"Viceroy Resource Corporation of Vancouver, B.C., has recently developed and brought into production the Brewery Creek Mine, an open-pit heap leach gold mine, located 55km east of Dawson City in Yukon, Canada. Mineable reserves are 15.2 million tonnes of ore grading 1.45 grams/tonne, containing 22 tonnes (707,315 oz) of gold. Ore processing employs the heap leach technology using run-of-mine ore. Highlights of 1996 activity included construction of a 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1. 46 gpt to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting of this mine has drawn significant attention because of the innovated heap leach technology; although this technology has been proven in other jurisdictions, it has not been used at such extreme northern sites where winter temperatures routinely reach -45°C for extended periods.ABSTRACT ONLY"

Jan 1, 1997

By H. Y. Sohn, S. PalDey

"Fine particles of nickel aluminides and Ni4Mo were synthesized by reducing mixtures of, respectively, A1Cl3 + NiC12 and NiC12 + MoC12 vapors with hydrogen. Though thermodynamically favorable, the coreduction of NiC12 and A1Cl3 by H2 to form Ni3Al did not readily happen experimentally. The addition of a small amount of aluminum vapor was needed to initiate the coreduction reaction. The product particles as observed by TEM were very fine but usually agglomerated. The electron diffraction pattern of particles identified NiAl and NiA13 along with Ni3Al and metallic Ni. The content of Ni3Al was maximized at 52 mol% at 1050°C under the partial pressures ofH2, A1Cl3, and NiC12 at 57, 1.4, and 0.5 kPa, respectively. When a mixture of NiC12 + MoC15 was reduced by hydrogen, Ni4Mo particles with some Ni or Mo particles were obtained, the maximum content of Ni4Mo obtained being 93 mol % . The particle size was in the range of 100 to 200 nm. An Ni4Mo coating of 700 nm thickness on an Ni substrate was also prepared.IntroductionThe search for new high-temperature structural materials has stimulated much research on intermetallic compounds. Nickel aluminides have low densities, relatively high melting points, and good high-temperature strength properties. They show an increase, rather than a decrease, in yield strength with increasing temperature (1). Ni4Mo is also of interest as a high-temperature structural material. The major shortcomings of these intermetallics are their inherent brittleness at room temperature when they are in polycrystalline form. For much the same reason, the conventional casting of intermetallics is difficult. Ingot metallurgy and powder metallurgy are two other processing techniques. The first technique is quite energy consuming. In powder metallurgy, the powders of metals and alloys are consolidated in near net shape and then subjected to secondary processing. It would, therefore, be advantageous if intermetallic compounds can be produced in fine powder form from inexpensive raw materials, using less energy."

Jan 1, 1998

By Yukio Ishikawa

Sumitomo Metal Mining Co,. Ltd. (SMM) has been producing 22,000 t/y of electrolytic nickel at Niihama by nickel matte electrorefining process since 1970. Although the matte electrorefining is an established process and the productivity has been greatly improved in the last 20 years, SMM has intensively developed the chloride process for the nickel production since 1970's. The nickel and cobalt refining process involving solvent extraction and electrowinning from the chloride solution has been successfully developed for the treatment of the mixed sulphide in 1975. The first application of chlorine leach to the anode slime has been succeeded since 1986. Based on those technology, the matte chlorine leach electrowinning process (MCLE) has been developed as an alternation to the relatively old technology of matte electrorefining. The new process offers significant cost down and excellent quality of the product. In 1986, the feasibility of MCLE was confirmed by the test work using the integlated pilot plant. The innovation of the chlorine leach process has been undertaken by this work. The new refining process can be divided into three stages including chlorine leach stage, purification stage and electrowinning stage. More than 99 % of nickel was extracted in atmospheric chlorine leach. Although copper ion was used for electron carrier in the chlorine leach, the excess copper from the feed matte is bled off from the leach circuit by de copperizing electrolysis. The copper ion of the pregnant solution is fixed on nickel matte by the cementation reaction. The nickel matte containing copper is processed in the chlorine leach. In the purification circuit, cobalt, iron and other impurities were removed from the nickel chloride solution. The nickel chloride solution is then fed into the electrowinning cell. Based on the process established, the new plant with a capacity of 330 t/M electrolytic nickel was commissioned in order to obtain the engineering data for design of the full scale plant in 1989. The performance of the plant was fully satisfied and the new process demonstrated the potential application of modern process control.

Jan 1, 1992

By Alan James Parker

Chalcopyrite can be converted to pure copper by the following five steps. An exothermic sulfation roast of chalcopyrite; leaching of cupric sulfate from the calcine with dilute acid; precipitation of Chevreul's salt and or other copper sulfites with ammonium sulfite or precipitation of crude copper by autoclaving ammonium sulfite and cupric sulfate at 150°C; dissolution of Chevreul's salt, or the crude copper, as cuprous sulfate, using acidic cupric sulfate in an acetonitrile-water solution as oxidant; precipitation of pure copper by thermal disproportionation of the cuprous sulfate solution. Acetonitrile and acidic cupric sulfate solution recycle. Advantages over conventional processes include lower cost, lower energy consumption as waste heat, sulfur removal as ammonium sulfate or gypsum, rather than as sulfur dioxide and rapid throughput. The net reaction is: 2 CuFeS2 + 4H20 + 15/2 02 + 8 NH3?2Cu + 4 (NR4)2 SO4 + Fe2O3

Jan 1, 1976

By Suzzann Nordwick

Over the past decade, significant advances have been made in the development of sulfate-reducing bacteria (SRB) technology to treat acid mine drainage (AMD). Bench-scale testing, field demonstrations, and engineered applications of SRBs for the treatment of AMD will be presented. Designs include an in situ bioreactor installed in the subsurface workings of the Lilly Orphan Boy Mine in 1994, the SRB bioreactors installed at the Calliope Mine from 1998 to 2001, the integrated biological reactors built at the Surething Mine in 2001, and the ongoing development of a replaceable cartridge system. SRB technology benefits include the reduction of dissolved metal ions to insoluble metal sulfides and the neutralization of the AMD resulting from the production of bicarbonate from the oxidation of organic nutrients. This paper will address engineering design criteria including the selection of organic media and system permeability and complete mitigation of AMD. Research was funded under Interagency Agreement No. DW899388-70-01-1 between the US EPA and the US DOE and was conducted by MSE Technology Applications, Inc., through the National Environmental Technology Laboratory (DOE Contract No. DE-AC22-96EW96405) at the Western Environmental Technology Office located in Butte, Montana.

Jan 1, 2003

By James Vaughan

Ionic liquids are solvents of interest for applications such as electro- plating, winning and refining of metals. Of particular interest is the possibility of processing reactive metals such as aluminium, magnesium and titanium that cannot be deposited from aqueous solutions. Aluminium has been electro deposited from AlCl3 : ionic liquid mixtures at low temperatures relative to conventional Hall-Héroult smelting. Imidazolium ionic liquids are have been used in the past due to their relatively high ionic conductivity and cation stability. The less studied and less expensive phosphonium ionic liquids systems may provide a viable alternative to imidazolium ionic liquids for certain applications. New information regarding the physical properties and electrochemical behaviour of phosphonium ionic liquid systems is presented.

Jan 1, 2006

By James A. Voigt

"The efficient separation of metal species from aqueous streams by precipitation techniques requires a fundamental understanding of the various processes that occur during precipitation. These processes include particle nucleation, particle growth by solute deposition, agglomerate formation, and agglomerate break-up. The application of the population balance approach has been used to develop a kinetic model that accounts for these competing kinetic processes. The usefulness of the model is illustrated through its application to the precipitation of yttrium hydroxynitrate, YHN. The kinetic parameters calculated from the model equations and system specific solution chemistry are used to describe several aspects of the effect of pH on the precipitation of the YHN. Implications with respect to the simultaneous precipitation of more than one cation type are also discussed through use of example systems. The effects of solution chemistry, precipitator design, and solvent choice are considered.IntroductionThe application of precipitation technologies to the separation of metals from solution is widely used. Regardless of its application, be it in such diverse areas as the preparation of metal oxide powders for use in commercial products or as a unit operation in the removal of trace metals during wastewater clean up, the fundamental processes involved are the same. These processes include: nucleation from solution, either homogeneous or heterogeneous; growth from solution with chemical reaction either in solution or at the precipitate/solution interface; growth by particle agglomeration; and particle break-up by collisional or shear forces. The effectiveness of the operation and the properties of the precipitate formed, or ""quality"" of the product, are determined by the competing kinetics of the different processes. The kinetics of the processes, in tum, are determined by system-specific solution chemistries and the conditions used to carry out the precipitation operation. For example, generally, when system conditions are such that the supersaturation driving force for precipitation is very high, growth species normally do not have the time to organize themselves with a high degree of crystallographic order and the precipitate is amorphous. In this case nucleation rates are invariably extremely high and the primary mechanism for growth is the agglomeration of nuclei. Conversely, when the supersaturation levels for the same system are reduced, the kinetics of the nucleation and growth processes also are greatly reduced, and a crystalline precipitate can be formed, since the growth species have time to order on particle surfaces."

Jan 1, 1996

By A. H. Rhoades

The modern polarizing microscope with such accessories as cameras, infrared devices, reflectance and/or transmission photometers, indention hardness, and heating stage is used to characterize coal, coke, and other carbon forms. It allows characterization of coke by-products, such as tars and pitches and their insoluble residues. A useful product of the microscopic approach is the coal petrographic analysis which permits the prediction of coke strength carbonization pressure and volume change. Carbonization tests are expensive, time-consuming and require large amounts of coal. Tests on the coke show it to be strong or weak but give no indication of why. Petrographic analysis requires grams of coal and yields data that indicates why the coal produces coke of a given quality. Small samples from drill cores are sufficient for petrographic analysis. These data are also used to optimize blends for coke production. When coke-plant problems occur, ~he microscope can be used to check the coal blend proportions, as well as for weathered coal. Microscopy is useful in spore correlation work which may be a prerequisite to sound coal reserve estimates. Dispersed vitrinoid reflectance studies are used to determine the degree of organic metamorphism which serves to establish oil and gas deadlines. Tars and pitches are examined microscopically for the amount of normal solids as well as the size of undesirable carry-over solids resulting from pollution abatement practices in coke works. The microscope is also used to study coals for gasification and liquefaction.

Jan 1, 1981

By R. G. Haire

Studies of the f-elements under pressure provide important insights into their solid state chemistry and physics. From such studies, of the elements and their alloys, it has been established that the normally localized f- electrons of several of these elements can become, involved in bonding under pressure. The electronic behavior of f-element compounds under pressure tend to be more difficult to interpret, due to the variety and the nature of electronic orbitals that are present. The 4f-elements and some 60% of the 5f-elements have been studied under The systematic comparisons that have been established for these materials are discussed.

Jan 1, 1992

By Thomas Niehoff

Many industrial processes require energy. Energy is required for melting or heating purposes. The heat can be generated by electrical heating or combustion/oxidation of hydrocarbons. Oxygen supports the combustion process. Oxygen is naturally contained in air with about 21 vol.-percent. The use of technical oxygen will allow an increase to the natural oxygen concentration of combustion air. Altering the combustion process by increasing the oxygen content has various effects. These effects are described and analyzed with regard to heat transfer, emissions and energy consumption. Industrial processes requiring oxyfuel are described and discussed regarding energy aspects.

Jan 1, 2008

By Bob Drew, Alfred Spanring, Kirschen. Marcus

"Increasing material conversion and energy efficiency, and decreasing carbon dioxide emission levels are crucial for sustainable production processes in the aluminum, cooper, and steel industries. RHI supports these targets by providing a diverse range of solutions including high quality refractory linings, optimum lining maintenance, and process improvements. In this paper examples are provided of process improvements and increased energy efficiency in copper refining, potential energy savings during electric arc furnace and ladle operations in the steel industry, and increased energy efficiency by improved heat transfer in anode baking furnaces in the aluminum industry. In all cases, RHI’s expertise in close collaboration with the customer resulted in an improved performance of the reactor lining and the actual high temperature process with a positive impact on the material conversion and energy efficiency and as a result a decrease in specific carbon dioxide emission levels.IntroductionRefractory linings play an important role in heat transfer during high temperature processes in for example the aluminum, copper, and steel production industries. Due to constantly increasing energy prices worldwide and the increasing demands for environmental and climate protection, improving the energy efficiency and decreasing emission levels of these energy intensive production processes is of significant importance. In this paper, the contribution of modern RHI lining technologies to energy saving measures and the corresponding reduction of specific carbon dioxide emission are described. The type of current refractory solutions for energy intense processes are illustrated with four examples: Optimization and increase of material conversion and energy efficiency in copper refining, energy saving potentials in both electric arc furnace and transport ladle operations in the steel industry, and heat transfer improvements during the carbon anode annealing process in the aluminum industry. These examples focus on particular production processes operating with a high proportion of recycled copper, steel, and carbon anodes. Increased energy efficiency directly decreases the specific energy related carbon emission levels whereas improvements to the metallurgical processes aim to increase material conversion efficiency and, therefore, decrease specific process related carbon emission levels. Significant energy savings can be achieved by maximizing the refractory campaign length through a combination of appropriate refractory material selection, grade zoning, correct installation, careful preheating, and effective maintenance strategies. Besides the efforts to improve the performance and energy efficiency of customer high temperature processes, RHI continuously promotes the development of new low emission carbon-containing refractory bricks and unshaped products."

Jan 1, 2008

By Larry M. Southwick

There is much ongoing work in research and development of new processes for the recovery and recycling of met.a.ls and other materials from various waste and scrap streams. Commercialization of such new technologies requires the bringing together and successful execution of a considerable effort involving a variety of activities. These include process conceptualization, research and development, detailed design and construction, and then plant startup and operation. Processes evolve through all of these steps by engineering due diligence, making objective and critical analyses of results, and troubleshooting processing steps to, hopefully, arrive at a sequence that has the best chance to succeed operationally and economically. After a summary review of the above steps, several processes will be described in more detail that provide mostly successful examples of the above procedures. Finally, some observations will be made on areas that will become critical in the near future to the success of new processes for wastes and residues.

Jan 1, 2000

By Shunsuke Yagi

A surface alloying technique was investigated using alternating pulsed electrolysis in an aqueous solution containing a single metal component for the formation of an Fe-Cr layer on an iron substrate. In the process, the iron substrate was dissolved during each anodic polarization of the pulsed electrolysis, providing iron ions in the vicinity of the substrate, while the Fe-Cr alloy was electrodeposited during subsequent cathodic polarizations. A bright, flat, and crack-free Fe-Cr layer with a composition gradient was obtained using a solution containing a trivalent chromium component and a complex forming agent together with some supporting or buffering salts.

Jan 1, 2006

By V. Vergara

Four copper composites were obtained by mechanical alloying, using as dispersed phases of four carbide powders; they were: boron carbide, chromium carbide, silicon carbide and zirconium carbide. The purpose of this work was to study some characteristics of these compounds and their feasibility for use as materials for electrical equipment. Raw materials used were copper powder finer than 150 mesh, and 2-4 vol % of powder carbides finer than 325 mesh. The alloying process was carried out using both a Spex 800-D mill with tungsten jars and balls and a hardened stainless steel jar and balls, the purpose of which was to measure the degree of contamination induced by the milling media. The changes in particle size, morphology and microstructure of copper alloys were studied with SEM and TEM for each alloyed powder. The degree of saturation of copper by the carbides was measured by X-ray diffraction. Sound samples were obtained by hot isostatic pressing at 1073°K. The best characteristics were obtained for the compound copper-chromium carbide, based on their hardness, tensile strength and electrical conductivity values. The other alloys failed due to their excessive brittleness after hot pressing.

Jan 1, 1999

By A. J. Rigby

Current practices employing porous plugs to inject nitrogen into molten copper during primary smelting are described. Nitrogen stirring increases heat transfer to the bath, eliminates temperature stratifications, and improves efficiency during the steps of desulfurization and deoxidation. The opportunity to use porous plugs as the means to introduce reducing gases to deoxidize copper is also discussed. Previously reported laboratory results using porous plugs, which point to very high utilization efficiencies of hydrogen when used as the reducing gas, are again reviewed. Advances in the design of the porous plug, and the introduction of a system enabling external replacement of plugs is also discussed.

Jan 1, 1999

By K. Asokan, K. Subramanian

"Electrowinning of copper by monopolar cells require common anode and cathode busbar and crossbars to connect each electrode to the respective common busbar. On the other hand, the bipolar configuration warrants the end electrodes only to be connected to busbars; there is substantial reduction in copper requirement. In the present work, an electrowinning cell with bipolar electrodes and end electrodes, each having an area of 1000 cm2 was designed and operated. The bipolar electrode is made of mixed metal oxide coated titanium mesh welded to plain titanium sheet. Coated titanium mesh acts as anode and the plain titanium sheet acts as cathode. Environmentally unacceptable lead anode and the recurring loss of lead are done away with. Closer spacing of the electrodes, paves way for the application of higher current density leading to mass transfer enhancement. Performance of bipolar copper electrowinning cell is reported.1. IntroductionThe normally adopted practice in electrowinning of copper is the conventional monopolar configuration. In this practice, the individual electrodes act either as anode or cathode. Hence there is a need to connect every one of the electrodes to the common anode or cathode busbar and crossbars running across the top of the cell are necessary. The common busbar carries very high current which is divided among the individual crossbars and hence has to be thicker in relation to the current load of the cell. The drawback of the need to use common busbars of thicker cross section and the need to have crossbars are obviated in the bipolar configuration."

Jan 1, 2009