Search Documents

By Yu Yamashita

There have been increasing in melting recycled scraps in copper smelting processes, and thus growing interests in the chlorine behavior. In this study, chloride dissolution in FeO-Fe2O3-SiO2slag (SiO2sat.) at 1523 K has been measured with varying in PCl2 from 1.13x10-8 to 1.30x10-7atm. and the oxygen partial pressures encountered in typical copper smelting furnace, i.e. PO2=10-8 to 10-10 atm. Discussion is made on the chloride capacity of FeO-Fe2O3-SiO2 slag in terms of its characteristics and the dissolved chlorine species. It has been shown that the mostreasonable dissolution reaction and chloride capacity can be expressed by the following reactions, where chlorine dissolves in the form of Cl-; here, aO2-, oxygen ion activity, is shown a function of oxygen partial pressure in the atmosphere. [ ]

Jan 1, 2006

By Andressa A. Silva, Esperidiana A. B. Moura, Francisco R. Valenzuela-Diaz, Jorge N. Sales

This work aims to study the influence of the nanoclay Cloisite 20A incorporation on mechanical properties of ABS (acrylonitrile butadiene styrene). The incorporation of Cloisite 20A was made in two steps; firstly,a masterbatch was preparated and then, it was incorporated in ABS. The Cloisite 20A masterbatch using 40 % of nanoclay and 60 % of SAN (Styrene Acrylonitrile) was prepared in an adiabatic mill. After that, Cloisite 20A masterbarch at 1 and 5 % (wt) was added in ABS. The resulting nanocomposites were characterized by tensile tests and the correlation between properties was discussed.

Jan 1, 2015

By Robert W. Hyers

Electromagnetic levitation has proven important in a wide range of experiments, all affected by fluid flow. For some experiments such as viscosity measurements, only whether the flow is laminar or turbulent must be established. For other experiments, however, quantitative assessments of velocity, shear stress, or shear strain rate are required. In most cases it is difficult or impossible to measure the internal flow in levitated droplets directly. The samples are usually small, opaque, reactive, high-temperature, metastable, or all of these. Furthermore, recirculating flow limits the utility of tracking surface particles, since they collect in stagnation points ratherthan following the flow. Most research groups have chosen mathematical modeling to assess the internal flow in levitated droplets. A variety of analytical and numerical methods have been applied, including both laminar flow and various turbulence models. A number of these models are reviewed and their impact on different containerless experiments is assessed. Much of the research reviewed here was performed by alumni of Professor Julian Szekely, and by others using similar methods.

Jan 1, 2006

By Y. Fautrelle, F. Felten, O. Metais, Y. Du Terrail

"We deal with the prediction of electromagnetically-driven turbulent flows by means of a Large-Eddy- Simulation method (LES). The model is applied in the case of a liquid metal pool submitted to a polyphase linear electromagnetic stirrer. We investigate two cases: (i) the frequency of the magnetic field is equal to 50 Hz; in that case the effects of the pulsating part of the Lorentz forces may be neglected; (ii) the frequency of the magnetic field is low (f= 1 Hz), then the oscillating part of the electromagnetic forces is taken into account. The LES predictions agree well with the mean velocity measurements, as does the standard k-a model. However, as for the turbulent kinetic energy predictions, there is a large discrepancy between the two models. When the oscillating part of the Lorentz forces is taken into account, the computations show that the fluid flow is sensitive to the unsteady part of the forces. We find that the mean velocity is not affected by the fluctuating component of the force. As for the turbulence parameters, the presence of the pulsating part leads to a significant reduction of the turbulent kinetic energy, whilst the turbulence length scale decreases.IntroductionElectromagnetic stirring is commonly used in various metallurgical processes. In continuous casting for example, it may improve the structure of the solidified metal products. Fluid flows generated by electromagnetic stirrers have been extensively investigated (1 ). As for numerical predictions, many works have been published on the subject. In most of the previous works, onepoint closure models have been used. The most used model is the well-known k-i:: model. Those models yield fairly good results as for the mean velocity prediction. However, it has two main drawbacks:(i) the turbulence is not predicted accurately,(ii) it is not well fitted for unstationary flows as well as transitional turbulent motions, where theReynolds number is moderate."

Jan 1, 1999

By Shinya Otsuka

Activity coefficient of oxygen in sulfide-rich and metal-rich melts in copper-sulfur binary were determined at 1423 and 1523 K by means of a modified coulometric titration technique using the following cell: 0 ( is Cu-S melts) I Zr02 (+Ca0) I air, Pt The activity coefficient values obtained in the present study increase rapidly with sulfur composition in the vicinity of xs = 0.3333. The data obtained for the matte saturated with the metal-rich melts are in good agreement with those obtained by Kuxmann and Benecke, Schmied 1, and Eguchi and Yazawa. Those obtained for the metal-rich melts are in good agreement with the results of Sano and Sakao.

Jan 1, 1983

By K. Th. Mavrommatis

Cleanness of steel is justified, measured and estimated in steelmaking process through different concepts which are mainly based on operational, empirical or semiempirical parameters and describe ?cleanness as a state?. In this work a theoretical concept is developed, considering ?cleanness as a process? and introducing a dynamic aspect into the quantification of cleanness of a steel melt, linking operational parameters with physicochemical variables, which are based on first principles. This concept and the here derived and developed variables and parameters are based on the earlier defined agglomeration index (AI) of a steel melt, the ratio of the mean inclusions diameter (MID) to the mean inter-particle distance (MIPD), which is shown to be a measure of the agglomeration tendency of the melt after deoxidation, and can serve both, to monitoring cleanness during steelmaking operation and to be useful as a basis for mathematical modelling of cleanness and of the metallurgical measures in plant, associated with production of clean steels.

Jan 1, 2006

By Norihiro Murayama

The hydrothermal syntheses of zeolites from coal fly ash were carried out using NaOH and KOH as an alkali source. The cation exchange capacity (CEC) and the ion exchange selectivity were investigated for the zeolites synthesized by a hydrothermal treatment. The effective usage of the zeolite as a cation exchanger was considered from the viewpoint of engineering. Zeolite P, HS (hydroxysodalite) and K-CHA (potassium-chabazite) are mainly formed as zeolite species in NaOH or KOH solution at 393K. The zeolite P and K-CHA have a large exchange capacity as a cation exchanger. The cation exchange isotherms of various monovalent and divalent cations with various zeolites are investigated. The order of selectivity of the zeolites is as follows, NH4+> K+> Li+.For the divalent cation, the largest removal amount is obtained for Pb2+ in the low equilibrium concentrations below 0.2mmol/dm3, and almost perfect removal can be achieved for Pd2+. The order of selectivity of zeolites in low concentration is expressed in the following order; Pb2+> Co2+> Cd2+> Ca2+> Mg2+> Ni2+. Ii is considered the zeolites obtained from coal fly ash can be used as an excellent cation exchanger.

Jan 1, 2006

By Ju Shao-hua

Although nowadays gold extraction methods are very abundant, none of them is satisfying, especially, in the field of heap leaching of low grade gold ore. The traditional heap leaching method of cyanide method plays an inglorious role of badly environmental pollution. In this paper, a bran-new and innoxious method of gold extraction system, metal-ammonium-chloride-ammonia (MACA), was proposed, and also analyzed both thermodynamically and practically. Thermodynamically, according to the principles of simultaneous chemical equilibrium and electronic charge neutrality, the thermodynamics of Au-NH4Cl-NH3-H2O system was studied by using the exponential computation method and through MATLAB programming, and the solid figure of its potential - c(NH4Cl) - c(NH4OH) was drawn. The results showed when the concentrate of ammonia is higher than 0.6 mol?L-1, fAu+/Au is only about -0.2 v. Practically, the leaching results of a cuprous gold ore showed that the extraction of gold can reach to 80% in this system. The preliminary results of reduction of the rich solution with copper and zinc powders showed that with deoxygenizing, the reduction effects were relatively good. These new findings and results have established a theoretical and practical base for developing a new process for heap leaching of low grade gold ores in this system. And the new process owns a series of merits such as, non-cyanogens, nontoxic, broader applicability.

Jan 1, 2006

By T. Yoshida

The Ni-MH (nickel metal hydride) rechargeable battery was developed several years ago. Its higher electrochemical capacity and greater safety compared with the Ni-Cd rechargeable battery have resulted in very rapid Increase in its production. The Ni-MH rechargeable battery consists of Ni. Co and rare earth metals, so that recycling is important to recover these valuable mineral resources. In this study. a basic recycling process for used Ni-MH rechargeable batteries has been developed, in which the Ni. Co and rare earth elements are recovered through a combination of mechanical processing and hydrometallurglcal processing.

Jan 1, 1995

By T. T. Chen

Secondary copper anodes are generally rich in Sn, Pb, Ni and Sb, but are notably deficient in Se, Te and Ag. In the secondary copper anodes, most of the Ni, virtually all of the Ag, slightly more than one-fifth of the Pb, about one-third of the As and Sb, and approximately one-tenth of the Sn are in solid solution in the copper. The remaining impurity contents occur as 1-5 µm grain-boundary inclusions in the anodes, and these are mainly Cu2O, SnO2, Cu-Pb-As-Sb-Bi oxide, Pb-Sb oxide, Sn-Ni-Zn oxide, Cu-Sn-Ni oxide, Cu-Sb-Ni oxide (Kupferglimmer) and trace Cu2(Se,Te). Barium sulphate, which originates from the mold wash used in casting, is also present in the anodes. During electrorefining, the BaSO4, SnO2, Pb-Sb oxide, Sn-Ni-Zn oxide, Cu-Sn-Ni oxide and Cu- Sb-Ni oxide inclusions are liberated and accumulate in the slimes layer. Solid solution Ni dissolves and the Ni accumulates in the electrolyte. Solid solution Sn and Pb dissolve, but partly reprecipitate as Sn arsenate and PbSO4, respectively. Solid solution Ag dissolves but rapidly reacts to form Ag2(Se,Te), Ag powder, Ag-bearing Cu2O, (Cu,Ag)SO4 or a complex oxidate phase. Partial dissolution of the Cu-Pb-As-Sb-Bi oxide particles takes place; the Pb component is converted to PbSO4, whereas Cu, As, Sb and Bi dissolve. The reacted particles retain the morphology of the original Cu-Pb-As- Sb-Bi oxide phase. Some of the solubilized As, Sb and Bi remains in solution, but much reprecipitates as SbAsO4, As-Sb-Bi oxide, and as a poorly defined oxidate phase which consists mostly of Cu-Ag-Pb arsenate-sulphate. The high Sn contents of secondary copper anodes do not seem to affect the behaviour of the anodes during electrorefining.

Jan 1, 1999

By Toshihiro Tanaka

The information on viscosity and surface tension of molten slag is indispensable to design new refining procedures in ferrous and non-ferrous processes. For example, the authors have tried to develop "Capillary Refining" to remove impurities in liquid metals by applying capillary absorption of molten slag with those impurities into solid fluxes which have a lot of small capillary tubes. It is necessary to adjust the above physico-chemical properties to adequate conditions on the capillary penetration. In the present paper, we discuss our recent trial to predict surface tension and viscosity of molten slag in multi-component systems. We have derived a thermodynamic model to predict the surface tension of molten slag by using ionic size, molar volume and surface tension of pure components. In addition, we have applied neural network computation to evaluate the viscosity of molten slag. We found good agreement of the calculated results with experimental values of the surface tension as well as the viscosity in various slag systems.

Jan 1, 2006

By Guray Kaya

Boron minerals are widely employed in various fields such as ceramic, glass, cement, metallurgy, etc. Although boron deposits of the world are limited, the production level of boron-based products is continuously increased. Turkiye possesses approximately 73 % of total world boron resources. Etibor Kirka Borax Company of Turkiye produces tincal concentrates and borax pentahydrates. During such productions considerable amounts of concentration and derivation wastes appear. Having considered the increased rate of production it is quite obvious that the level of relevant wastes will also be raised. With this study it was aimed to utilize these wastes in roof tile and brick bodies and to convert them into a form environmentally and human friendly. Newly produced products were undergone to several standard tests for the determination of their shrinkage, water absorption, strength values and coloring parameters. Additionally, micro structural studies were conducted.

Jan 1, 2006

By Guojun Ma

The entrainment of charge materials, evaporation or volatilization of elements and ejection of slag and metal by spitting or the bursting of gas bubbles are mechanisms whereby stainless steel plant dust are generated from the electric arc furnace and refining converter. TCLP and ASTM D 3987-85 tests on dust that was collected from the baghouse filter system of a South African Stainless Steel plant showed that this dust can be considered hazardous according to South African legislation, due to the high degree of Cr (VI) leachability (~13mg/l for TCLP and ~8mg/l for ASTM vs. regulation threshold of 0.05mg/l in drinking water). The dust is therefore considered to be harmful to both the environment and human health, due to its high solubility in water and carcinogenic properties. It should therefore be treated before being stockpiled or land filled. This paper consequently describes an investigation into the formation of Cr(VI)-containing stainless steel plant dust and the stabilisation thereof in a sintering process, whereby the dust was mixed with a silica-rich clay. It is postulated that Cr(VI) form when the (Mg,Fe,Mn,Cr)3O4spinel phase, CaO, Ca(OH)2 and CaF2 (all of which are present in the dust) react. This reaction was found to take place both at ambient and at high temperatures (1100°C). Stabilization of Cr(VI) in the dust could be achieved at an optimum sintering temperature of 1100°C for a 50mass% dust : 50mass% clay mixture. Chromium emission during the sintering process was found to be low, and within environmental limits.

Jan 1, 2006

By Allan J. MacRae

A copper alloy to be used for coils in cast copper cooling blocks has been identified and samples prepared for metallurgical examination and destructive testing to compare with cast cooling blocks manufactured from copper and nickel-copper alloy pipes. The copper alloy allows for the formation of a metallurgical bond between the pipe and the cast copper during the casting process, which does not normally occur with pure copper or nickel-copper alloy pipes. The alloy's coefficient of thermal expansion is also much closer to that of pure copper compared with nickel-copper alloys, so there is less strain induced at the pipe-cast copper interface due to differential thermal expansion. It is expected that this new pipe coil alloy and associated casting techniques will allow for the production of cast copper cooling blocks that have greatly enhanced service life in high heat load applications compared to existing technologies.

Jan 1, 2002

By Victor Bredykhin

The reasons of formation low quality cathode deposits and conditions of the anode passivation in electrorefining of copper silver alloys with increased (more then 5%) silver content in electrolyte, g/l: Cu - 40; H2SO4-50; 150 and 250; T= 401C have been investigated. As it is shown, increased acidity, anodic current density and silver content in anodes favor passivation. The assumption is made that the ingress of silver on cathodeis the most probable reason of growing dendrites on cathode. We have determined that addition of ethylene carbonic acid to electrolyte in the amount of 3,5 ÷ 10 ml/l suppresses the dendrite formation.

Jan 1, 2006

By Carla Lupi

In this work, nickel-cobalt electrodeposition under galvanostatic conditions was investigated. Ni-Co alloy was electrowon from an acid sulphate bath containing 40 g/L Ni and2-8 g/L Co.. The effect of electrolyte composition, current density, temperature, solution pH and presence of buffers such as H3BO3 and (NH4)2SO4 on Co content of the binary alloy has been investigated. In particular, current densities ranging from 180 to 400 A/m2 and temperatures ranging from 27 to 60°C were tested. The composition of Ni-Co alloys may be diversified through the selection of process parameters. The experiments show that the highest cobalt content of the alloy is reached by using a buffer free electrolyte without solution pH control. Though, in these conditions, the most homogeneous, fine and regular deposit morphology is obtained, energy requirements are the highest in tests lasting just two hours.

Jan 1, 2003

By Henrique Ventura Oliveira

Continuous casting is the most important process for solidification of steels. In this process, the fluid flow pattern in the tundish and in the mould have significant effect on the product quality. Problems associated to fluid flow in the tundish include surface turbulence, ?short-circuits?, formation of dead zones and vortexing. During grade changes, mixing in the tundish plays a significant role in determining the length of the intermixed slab. All these flow aspects can be studied by means of mathematical and physical models. In the last years, numerical simulation of fluid flow has become a very popular tool in the analysis of the performance of continuous casting tundishes. In setting-up these numerical simulations, special care should be taken in choosing the appropriate mesh distribution, the interpolation scheme, the adequate location of the inlet boundary and the turbulence model. In the present paper, turbulent fluid flow in different configurations of tundishes was simulated. Different turbulence models were used in the simulations. Residence time distribution (RTD) and mixing curves during grade changes were predicted and compared to results obtained in physical models. The performances of the different turbulence models were evaluated. For the tundishes that have been studied, the performances of the different turbulence models tested in the present work were similar. There is no evidence that any of the models provided sustained improvement when compared to the well-established standard k- model. All turbulence models tested presented limitations in simulating flows under low turbulent Reynolds numbers.

Jan 1, 2006

By P. Chris Pistorius

Calcium treatment of alumina inclusions, to convert the alumina to molten or partially molten calcium aluminates, is a well-established treatment for steel, to improve the castability of aluminium-killed steel. However, the role of magnesium in calcium-treated steel is not fully clear, nor is the origin of the several percent of magnesium oxide that is often present in calcium-treated inclusions. To study this, steel was sampled after calcium treatment at an industrial steel plant, and the inclusions identified by energy-dispersive X-ray microanalysis (EDX) on polished sections of the samples (analysing the samples in a scanning electron microscope). The predicted fraction liquid in the inclusion was estimated from the ternary alumina-magnesia-lime phase diagram. Inclusions with higher CaO contents generally had lower MgO contents, indicating that the calcium wire is not the origin of the magnesium in the inclusions; this was also confirmed by wet chemical analysis of the calcium wire. Instead, it appears that magnesium-alumina spinel inclusions form during extended ladle contact after aluminium killing and before calcium treatment. While such spinels have been stated to cause poor castability (clogging the submerged-entry nozzle), it is clear that calcium treatment successfully modifies the spinel inclusions to mixed alumina-lime-magnesia inclusions, where the magnesia content contributes substantially to liquefaction of the inclusions: for typical MgO contents of around 10%, the range of Ca:O ratios which yield liquid (or partially liquid) inclusions is extended substantially to lower Ca:O ratios.

Jan 1, 2006

By Metehan Erdogan, Furkan Özdemir, Ishak Karakaya, Mustafa Elmadaglı

Tungsten is mainly produced by H2 reduction of WO3 which makes its production difficult and costly. A promising method was recently reported for direct electrochemical production of tungsten from CaWO4 (scheelite) which is estimated as the seventy percent of the all tungsten reserves of the world. This paper investigates the application of pulse current in the electrochemical reduction of CaWO4 pellets attached to a current collector. The electrolyte was composed of calcium chloride and sodium chloride salts at eutectic composition (48 pct mol NaCl at 873 K). The reduced samples were cleaned with dilute hydrochloric acid solutions and characterized by X-ray diffraction and scanning electron microscopy. Examination of the results revealed that metallic tungsten was obtained by pulse current reduction.

Jan 1, 2016

By Seung-Whee Rhee

Characteristics of ceramic support made by spent foundry sand-loess mixtures are investigated by bulk density, porosity, durability, and compressive strength. And the basic properties of SFS and loess are estimated. The effect of drying time after cutting process, elevated temperature time, sintering temperature, and sintering time is also estimated to obtain the optimal condition in the process of manufacture ceramic supports. From the basic properties of SFS and loess, the content of SiO2 in furan sand is much higher than that in loess but the content of Al2O3and Fe2O3 in furan sand is much lower than that in loess. In order to make ceramic supports cylinder shape is the most desirable to sustain the properties of ceramic support. If annulus shape has a enough compressive strength, however, annulus shape may be decided. For the optimal condition to manufacture ceramic supports, drying time after cutting process is decided to 24 hrs and elevated temperature time is decided by 9hrs. And sintering temperature and sintering time are decided to 900 and 9hrs, respectively in order to prevent solidification of sand materials.

Jan 1, 2006