Search Documents

By C. Lupi

Zinc chloride electrowinning presents difficulties in obtaining smooth, compact and dendrite free deposits with a high current efficiency due to the presence of undesirable metal ions. However, it is hard to define a level of impurities tolerable in zinc deposition, and despite a lot of research in this field, the reaction mechanisms of the undesired metal ions are still not clearly understood. In this study, the influence of Fe, Cd, Co, Ni and Cu additions were investigated, as well as their synergic effect on the zinc electrodeposition process from chloride electrolytes and on the obtained deposit morphology. The tests were all performed in presence of TBACl which reduces the harmful effect of such impurities on the zinc reduction.

Jan 1, 2003

By W. Kasprzak

Press-fit systems are widely used to seal oil lines in the automotive engine components. In the case studied a ball plug made from the 7075 A1 alloy was inserted into a 319 Al alloy cast component. The oil lines were subjected to the required component service pressure. This paper addresses the analysis of the ball plug/casting hole press-fit performance. The tools used to investigate the plug system included: the SEMIEDS technique for the assessment of the plug and the casting hole wall surface integrity; image analysis methods for the characterization of the ball plug/casting hole interface; matrix microhardness measurements of the plug and casting components; laboratory ball plug insertion, speed and force correlation; as well as the ball shearing mechanism analysis. Laboratory tests indicated that optimization of the aluminum matrix hardness in the 319 A1 alloy cast components resulted in considerable improvement of the press-fit system sealing properties.

Jan 1, 2002

By B. I. Hop

The f10wfield set up by the standard Hydro gas purging unit has been predicted by a numerical model. In addition turbulent trajectories of gas bubbles released from the rotor are predicted. Here the deposition rate of inclusions on the bubble surface is allowed to depend on local conditions. Bubbles passing regions with strong pressure gradients, such as close to the rotor, will experience large slip velocities and large deposition rates. This model can deal with any distribution of bubble sizes and inclusions. The results found from the multidimensional flow predictions are discussed in relation to what can be obtained from a much simpler metallurgical engineering approach. The differences between these two approaches to predict the same process will be discussed. The model predictions are compared to experimental results for removal of SiC-particles from aluminium.

Jan 1, 1996

By Moo Eob Choi

The reduction of iron oxide particles by hydrogen is one of the most widely investigated gas-solid reactions. The search for new methods for producing iron by the direct reduction of iron oxide has resulted in a large number of exhaustive studies of the various aspects of this reaction. However, previous studies have largely been done with either pellets or lump ores. Little has been published on the hydrogen reduction of very fine concentrate particles smaller than 37 µm (-400 mesh). The kinetics of hydrogen reduction of fine iron oxide concentrates were investigated in the temperature range of 900 - 1300°C.

Jan 1, 2006

By Ali Akbar Mottahedi

It is known for a long time that the reaction of oxygen with carbon, silicon, iron and many other elements is exothermic. The heat of released from these kind of reactions can decrease the time of fusion of iron and steel for metallurgical purposes in the electrical arc furnaces. By decreasing the time of fusion, we increase the rate of process and the amount of production. So, by blowing oxygen in to the furnace, we can reduce the consumption of electricity and save cost. There are many problems in the procedure of the oxygen blowing. In this project, the theoretical aspect of the oxygen blowing and its side effects into the arc electric furnaces are investigated. An oxygen blowing system into the arc electrical furnace of metallurgy department of Machine Sazi factory was also set up. This process reduced the consumption of electricity up to 22% and increases the rate of production, by reducing tap ? to ? tap time up to 15%. In this project; all oxygen blowing systems and its control were set up.

Jan 1, 2006

By Osvaldo A. Bascur

Several new hydrometallurgical plants have been built in the past years. They have implemented new processes to treat new type of ores. New technologies have been used to improve metallurgical performance from the start. The cycle times between knowledge generation and innovation are often neglected in the traditional capital expenditures and building of these new process plants. The paper reviews several implementations in which they have started with new ways of using information management from the beginning. The implementation of a real time performance management infrastructure is reviewed to assist in the implementation of mine to product strategies, metallurgical mass balances, solvent extraction composition statistical process control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to improve operations by simplifying the access and analysis of information from assets and metallurgical processes. Continuous improvement and innovations have been enabled to minimize start times and for faster troubleshooting and resolution of operational problems.

Jan 1, 2006

By James D. O, DeLa&apos

Multicomponent materials are common in nearly all areas of materials science and technology, yet the use of phase diagrams to represent these complex systems is hampered by the requirement of three or more dimensions for explicit graphical representation. In the present work, the "solid-modeling" capabilities of a computer aided design (CAD) system have been applied to the representation of three-dimensional phase diagrams. Relevant phase diagrams for a hypothetical quaternary eutectic system were constructed and used to demonstrate the capabilities of the technique. These capabilities lead to relative ease of phase diagram construction and improved access to qualitative and quantitative information. Results of this work are contrasted and compared to previous efforts toward computer ,representation of phase diagrams. It is concluded that solid-modeling of three-dimensional phase diagrams can be used to advantage in both education and research.

Jan 1, 1991

Electrocrystallization studies were conducted in a concentrated acid-copper electrolyte to determine the influence of chloride ions and glue on copper nucleation and on the structure of thin copper layers. Electrochemical experiments allied to SEM and XRD examination were performed to characterize the mechanism of nucleation in the presence of additives at 65°C. Results indicated that most of the copper nucleation from a 83 g dm-3 Cu2+ solution, with 140 g dm-3 of H2SO4 is achieved in a matter of milliseconds, Although the presence of chloride and glue, at the concentration levels tested, does not seem to substantially modify the nucleation mechanism, the morphology, nuclei density and the copper film structure and orientation are changed by the presence of additives and by electrolyte stirring.

Jan 1, 1999

By Mamoru Kuwabara

A high-power sound which can transmit through any continuous elastic medium with less attenuation, particularly in liquid allows us to externally control the system of concern by using the acoustic radiation force or the cavitation phenomena. These functions may eliminate gravitational and/or atmospheric constraints which are often encountered in conventional operations for producing clean and advanced materials. This paper outlines the recent development in the field of sonoprocessing of materials. Cold model experiments in some vessels have been performed to simulate ultrasonic operations such as inclusion removal from liquid, degassing of melt, emulsification of two liquid phases, solidification processing, and decomposition of chemical species in waste water. High speed visual imaging is carried out for better understanding of the cavitation phenomena as well as the followed microjets during the processing. The radiation force acting on fine suspending objects in a fluid can be utilized for eliminating or rearranging/orienting the objects in the fluid. Acoustically induced cavitation phenomena in liquid can be utilized as an effective dynamic means to control interfacial phenomena as well as micro- and macro-mixing of liquid. Sonochemical and thermal effects in cavitation multi-bubble can be also useful in a waste water treatment.

Jan 1, 2006

By Alfonso Nájera

Turbulent flow of liquid steel and its control is studied using different geometries of turbulence inhibitors. Four designs of turbulence inhibitors were characterized through experiments of tracer injection I a water model and mathematical simulations using the Reynolds Stress Model (RSM) of turbulence. Geometries included octagonal-regular, octagonal-irregular, pentagonal and squared. A layer of oil was used to model the behaviour of tundish flux during steel flow. Fluid flows in a tundish using these geometries were compared with that in a bare tundish. Experimental and simulation results indicate that the flow in the bare tundish and a tundish using turbulence inhibitors open large areas of oil due to strong shear stresses at the water-oil interface but the squared inhibitor. These phenomena are explained by the high gradient of the dissipation rate of the turbulent kinetic energy using the squared inhibitor. Using this device the kinetic energy reports a high gradient from the tundish floor to the free bath surface as compared with other geometries.

Jan 1, 2006

By L. H. Lewis

The relationships that link microstructural properties of advanced permanent magnet materials with magnetic properties such as the coercivity are often difficult to quantify, especially in materials with nano-scale structures. Recent work on RE2Fe14B-based powders fabricated with rapid- solidification techniques such as inert gas atomization (IGA) and melt-spinning provide insight into the nanostructural features which affect the acquisition and stability of coercivity. In all cases the coercivity is found to be a function of both the scale of the constituent microstructure and of the presence and distribution of minor phases.

Jan 1, 1997

By M. G. Basavaraj, S. Sarkar, G. S. Gupta, P. D. Patil

"Previous experimental study on raceway size hysteresis on two-dimensional cold model showed that the inter-particle and wall-particle friction had a very large effect on the raceway size. Existing literature correlations for raceway size ignore the frictional effects. It has also been shown in the present study that their applicability to the ironmaking blast furnace is questionable. To take into account the effect of friction on the raceway size a stress analysis has been done for the raceway region. Two-dimensional fluid flow equations under turbulent conditions have been developed and solved computationally in order to get the pressure forces. The frictional forces were obtained in terms of stresses. To predict the raceway size a force balance was done for the raceway zone considering the pressure force, the frictional force and the bed weight. The resulting equations from the force balance are able to describe the raceway hysteresis phenomena reasonably well along with the raceway size. A two dimensional experimental set up has been fabricated in order to validate the computer predictions. Predicted values agree well with the experimental values.IntroductionWhen a high velocity blast of air is introduced into a packed bed through a tuyere, a cavity is formed in front of the tuyere. This cavity, formed in the iron-making blast furnace, is called the raceway. Coke tumbles down and bums in this raceway, generating heat and reducing gases for the iron-making process. The raceway is responsible for producing most of the reducing gasses in the blast furnace. In addition, the size and shape of the raceway determines the movement of solids within the blast furnace, the distribution of gases and liquids (slag and metal), setting the location where the primary chemical reactions occur and the temperature profile in the lower part of the blast furnace.Due to the importance of the raceway, many investigators l - 6 have studied it and have predicted the raceway size using the empirical correlations based on experimental (hot & cold) and mathematical models. A number of correlations have been reported in the literature to predict the raceway size by various investigators3 - 6 which are different to each other. Each of the correlations shows a different dependence of raceway diameter (DR) on bed height, particle size, solid density, bed voidage and blast velocity. None of the correlations includes the effect of solid stresses on the raceway size and shape. The magnitude of these stresses will depend on the bulk solids properties (internal angle of friction, wall angle of friction) and the bed dimensions."

Jan 1, 2001

By Tomas Astorga

APEC, the Asia Pacific Economic Cooperation is the forum of 21 countries having approximately 56% of the total world income, and over 45% of global trade. In 1997, APEC economies produced 67% of the world copper output, 55% of gold, and over 45% of other base metals. Mining in APEC captures more than 60% of the total mining investment in the world. New and emerging economies are now appearing in the demand scenery, such as China. New trends in the international environmental regulations are posing questions related to the use of copper in different industrial and consumption applications. These may have a strong impact on future trade of copper. New applications are also appearing based in new technology fields. The paper examines the growth potential of the copper market in main consumer ad highly populated economies of APEC, incorporating analysis of various interrelated factors. It also analyses the outlook of the copper supply. Its conclusions point to the need to implement demand outlook models. Finance and economic reforms will open important avenues for trade growth in basic metals, particularly copper. Changes in the consumption patterns of highly populated countries will add to better perspectives of copper demands. The recovery of a fast pace of economic growth in the APEC region will bring new demands for copper, especially as a consequence of high tech applications. More extended policies focused in the need for developing energy efficiency programs and schemes will add to this picture.

Jan 1, 1999

By Yoshio Waseda

A laser flash method has been applied to obtain the thermal diffusivity values of Zr55Al10Ni5Cu30 alloy in the liquid, glassy, crystallized and supercooled liquid states. The electrical resistivity of this particular alloy was measured in the glassy, and crystallized states by a direct current four probe technique. A specific heat of Zr55Al10Ni5Cu30 alloy was also determined by a differential scanning calorimeter in the glassy state. On the other hand, thermal diffusivity values for two alloys of Zr60Al15Ni25 and Zr65Al7.5Cu27.5 were measured in the crystallized and liquid states. The thermal diffusivity values of three Zr-based alloys in the liquid state are summarized in the linear equations with positive temperature dependency and it is noted that the lower the thermal diffusivity values of Zr-based alloys at liquidus temperature, the lower the critical cooling rate to obtain metallic glass phase becomes. The thermal diffusivity values of Zr-based alloys were compared with those of Pd-based alloy case. These results suggest that thermal diffusivity of alloy liquids might be an indicator of the glass-forming ability of Zr-based and Pd-based alloys.

Jan 1, 2006

By Merete Tangstad, Ragnar Tronstad

Ferromanganese production in electrical furnaces is quite an old process. However, as the furnaces are getting bigger, the requirements of cost, yield, product quality, emissions and security are raised. With the increased expectations, the fundamental knowledge must follow. Within the last 25 years there has been a great effort both in the industry as well as the academic environment to push the limits of this process. This article will show some examples of improvements within fundamental data, reaction mechanisms and emissions over this time period.

Jan 1, 2014

By Beatriz Ramírez

Xanthates are anionic collectors normally used in flotation devices to modify the hydrophobic surface of sulphide minerals. Xanthates are heteropolar compounds and in aqueous media they dissociate into ionic xanthate and alkali-metal ions; nevertheless their behaviour is not well understood yet. This work characterises the six reactions describing the decomposition of the ionic xanthate in aqueous media by analysing the set of spectra from a UV- Spectrophotometer. Results show the effect of pH on the stability of certain compounds which can be useful to explain the relationships among xanthates and the hidrophobicity of some surfaces (or ions dissolved).

Jan 1, 2006

By A. V. Tarasov

One or more of the main alloying metals, i.e. copper, silicon, nickel, magnesium, zinc and other metals can form a composition with aluminum, by dissolving in the latter. The thermodynamic computations have indicated that within a range of temperatures from 700°C to 1300°C the reactions of molten aluminum with zinc and nickel oxides are shifted toward formation of free metals because it is possible to use the main alloying metals, i.e. zinc and nickel, in the form of inexpensive intermediate products and waste. The laboratory studies conducted have confirmed a possibility for production of aluminum alloys using intermediate products in the form of oxides of alloying metals.

Jan 1, 2006

By F. E. Katrak

Rare earths markets by definition usually include not only the rare earth elements, but also yttrium. They can be subdivided into a very large light rare earth fraction (about 95 percent by weight of all rare earths consumed) consisting mainly of cerium and lanthanum and a smaller fraction (with much higher unit value) consisting of selected high-purity oxides or elements such as yttrium, europium, samarium, or neodymium. CRA estimates that the noncomnunist world market for all rare earths and yttrim was on the order of US$750 million in 1986. The main focus of this paper is on the principal uses for rare earths, some CRA-developed proprietary data on their consumption by region, and the selective nature of business opportunities in the rare earth markets. We also provide forecasts on the future trends in these markets.

Jan 1, 1989

By Jimsher Aneli

The investigation of some peculiarities of conductivity dependence on filler type and amount in the polymer composites has been conducted. It is established, that conductivity of composites based on phenolformaldehide resin essentially depends on proportion of double fillers: graphite + carbon black, graphite+ andesite, contained in composites. It was shown, that these composites characterized by synergetic effect ? non additive influence of fillers concentration on the conductivity of composites. Some other properties of composites contained binary fillers (effect of temperature and pressure on the conductivity) have been investigated.

Jan 1, 2006

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. Green balls with 0.8% bentonite and others with 2% hydrated lime were obtained under the same conditions of 1.5% coke, 1.45 basicity and balling at 8.5% moisture for 13 min in disc pelletizer. The properties of two types green balls were as follows: drop numbers of 4.8 to 5.0 times/0.5m, compressive strength of 19.7 to 24.2 N/pellet and thermal shock temperature of 280 to 385?, respectively. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8% and climbs up to 3113 N/pellet under the following conditions: preheating at 1050? for 10 min and firing at 1300? for 15 min. The hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6% to 70.6%, RDI+3.15 increased from 90.1% to 98.8% and reduction swelling index dropped from 22.4% to 7.4%, respectively. Therefore, hydrated lime can not only replace bentonite as binder to enhance the firing behaviors of green balls, but also effectively improve the metallurgical performance of fluxed pellets which can be used as high quality feed for blast furnace.

Jan 1, 2011