Search Documents

By J. Bostjancic

As wastewater discharge regulations become more stringent, power plants, manufacturing plants and other industrial sites are looking for ways to reduce makeup water requirements and to recycle and reuse as much wastewater as possible. In some cases, environmental regulations require zero liquid discharge, meaning all wastewater must either be retained on site or reduced to solids for disposal off site. Zero liquid discharge or "closed-loop" wastewater treatment systems using evaporators and other process equipment have been well-accepted in recent years. Often overlooked is the fact that zero discharge is not just the latest fashion--many commercial zero liquid discharge systems have been in operation since the mid-70's. This paper will give specific examples of zero liquid discharge operations from 1974 to the present, showing how evaporation equipment and processes have changed to meet the requirements of industry and environmental regulations.

Jan 1, 1996

By N. Voennann

Stillwater Mining Company operates an electric furnace at its smelter in Columbus, Montana to treat a Ni-Cu-platinum group metal concentrate along with secondary PGM bearing materials. Hatch Associates has designed several improvements to this furnace, which was originally built by others. Implementation of these relatively low cost improvements has resulted in substantial increases in furnace availability and capacity, along with reduced unit costs. ? The improvements included: ? Installation of water-cooled copper cooling elements to stabilize refractory wear and increase furnace life.- ? Improved furnace 'bindings, to enhance the furnace's structural integrity by improving the contact between the refractory and cooling elements, and by promoting tight brick joints resistant to matte or slag leaks. ? Adjustment of the electrode regulator to allow higher furnace power levels. ? Installation of an automated air-slide (aeration conveyor) feed system to evenly distribute the furnace feed in an insulating layer on the bath surface. This "black-top" practice reduces unit energy costs and makes available additional smelting capacity.- ? Electrode seals to reduce ingress of air that absorbs heat before exiting the furnace in the off-gas stream. The saved energy can be used to smelt additional concentrate. This paper describes the above furnace modifications, and the benefits derived from their implementation.

Jan 1, 1998

By Stephen Gale, David Clarry, Edmund Smith, Jon Feldman

"In 2006, a Canadian steel maker embarked on an ambitious initiative to become “Best in Class in Energy Management”. This initiative provides the framework for this paper, with some augmentation from other energy management projects carried out by Hatch. The initiative focused on identifying energy/GHG management improvements leading to low-cost implementation of energy savings or GHG emission reduction. The key components of the approach were:• Review site energy management practices and benchmark internationally.• Review best technical practices and benchmark against public energy intensity data.• Conducted a site-wide Energy Assessment and physical review of operating areas.• Facilitation of on site-workshops with staff to prioritize savings opportunities, as well as identify and remove implementation barriers.• Development of an Energy Management Action Plan for implementation of improvements.Most organizations can produce, with relative ease, a list of ideas for saving energy, implementing them is the challenge. This paper addresses these issues as well as the profitability of the energy efficiency improvements and the consequences for GHG emissions.IntroductionWhen one of the authors was an undergraduate engineering student at the University of Cape Town in South Africa, the technical drawing instructor made a statement that was both humorous, and mildly profound. He claimed that the most successful engineer is one who is both lazy and diligent. Lazy, in the sense that the engineer is constantly on the lookout for an easier, more efficient, way to do something. Diligent, in the sense that the engineer will work tirelessly to come up with a good technical solution for the easier way. This paper, somewhat of an anomaly in a compilation of technical proceedings, hopes to break the mould a little, and to show a “lazy-diligent” way of reducing the carbon emissions from an industrial facility, using a steel plant as an example."

Jan 1, 2008

By Gus Van Weert

The cost of oxygen is a major and common factor in the hydrometallurgical processes developed or proposed tor the oxidation of refractory pyrites. This cost involves charges for the generation and the transfer of the 02 to the mineral slurry. Bio-oxidation faces considerable design demands which require large scale equipment to be resolved. Nitric acid assisted oxidation offers low cost oxygen units; this method of pyrite oxidation deserves a closer look for large scale plants treating pyritic gold ores and concentrates.

Jan 1, 1990

By M. Ide, K. Takemura, S. Taenaka, K. Shinzawa

"The laser characteristic is strongry dependent upon the stoichometry of forsterite (Mg2Si04) and YSO (Y2Si05) single crystals, because of change in the valency and occupied sites of doped Cr in the lattice so that mole ratios of Mg0/Si02 and Y203/Si02 in the above single crystals must be precisely analyzed. In this study ICP-AES was applied for analyzing the mole ratios. Emission intensities corresponding to Si and Mg or Si and Y were measured at the same time with internal standard method. Preparation of sample solutions, measurement conditions of ICP-AES and interferences by coexisting components were discussed, resulting in excellently precise detennination of stoichometry of the above single crystals.IntroductionIn conventional stoichiometric analysis of single crystals, the stoichiometry is detennined by analyzing each component separately with titrimetry and gravimetry techniques. On the other hand, by stoichiometric analyses using ICP-AES, emission intensities corresponding to components are measured at the same time with internal standard method. Consequently erros caused by variation of analytical condition are canceled out.Cr-doped Mg2Si04 and Y2Si05 syngle crystals are known as laser materials. The change of valency and occupied sites of doped Cr affect the characteristic of single crystal as aleser materials. The change of state of doped Cr.Stoichometric composition of Mg2Si04 is constructed by 2mole of MgO and 1mole of Si02, and Y2Si05 is constructed by 1mole of Y203 and 1mole of Si02. In this study, required analytical precision in component mole ratio is within an error of 0.0010 for Mg2Si04 (CV=0.05wt%), and within an error of 0.0030 for Y2Si05 (CV=0.05wt%) (Table I )."

Jan 1, 1998

By Evgueni Jak

Pyrometallurgy is an important sector of modern industrial society actively participating in solving current environmental, economic, materials scarcity and other challenges. Recent advances in analytical methods, experimental techniques, thermodynamic, phase equilibria and process modelling tools provide new opportunities to increase the productivity of pyrometallurgical reactors, the treatment of complex feeds and metal recoveries. Fundamental theoretical models can now be used to make a significant next step towards the development and implementation of computerised models describing real industrial processes—Virtual Reactors, and computer-aided smart-decision-making systems that may be called Pyro-GPS by analogy to GPS; these developments can facilitate knowledge-based improvement and optimisation strategies. The implementation of these improvements require ongoing collaboration between researchers, industry and government.

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008

By SM Rao

Nuclear Fuel Complex (NFC ) , Hyderabad (IN DIA ) , is engaged in the manufacture of nuclear fuel assemblies and zircaloy structural components required for the Indian nuclear power reactors. The production of zirconium oxide, sponge and zircaloy materials through chemical and hydro - metallurgical processes generates many effluents containing valuable zirconium and hafnium . This paper deals with the various processes such as multiple crystalization, phosphate precipitation, ion-exchanges amine solvent extraction etc, for the treatment of these effluents and subsequent recovery of valuable zirconium and hafnium .

Jan 1, 1992

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By K. L. Money, R. R. Bleakney, R. H. Hanewald

The processing of EAF baghouse dusts, rolling mill scales, and belt grinding swarfs from the specialty steel industry will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions, filter cakes, spent nickel and chromium plating baths, super alloy wastes, and nickel-cadmium batteries. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery.

Jan 1, 2000

By Peter Woodall, Paul Telford, Pengfu Tan

"Arsenic enters the Mount Isa copper circuit in the form of arsenic rich minerals in concentrates from both the Mount Isa and Ernest Henry copper mines. Arsenic is a volatile metal, and will partition in the copper smelter between smelter off gases, slag and anode. Most of the volatile arsenic will report to Isasmelt Electrostatic Precipitator (ESP) or Waste Heat Boiler dusts where it will form a re-circulating load within the smelter. ESP dust is produced at a rate of 15,000 - 20,000 t/y and is currently removed from the precipitator and leached in the new ESP Dust Recovery Plant to separate copper and arsenic from the ESP dust. This paper describes the laboratory test works of ESP dust leaching, neutralisation and cementation processes. The planttrial, commissioning and operation have been presented as well.1. IntroductionThe flue dusts generated in the process of copper smelting contain appreciable amounts of copper and other valuable metals including precious metals. These flue dusts also contain appreciable amounts of arsenic trioxide where arsenic occurs in the ore body. The copper smelters processing concentrates generate residuals, such as ESP dust, containing arsenic trioxide. ESP dust contains impurities such as arsenic and bismuth which are harmful to the copper refining process if they report to anode. These impurities are fumed off in the smelting process and report to the dust as arsenic and bismuth oxides.The content of arsenic in the feed of Mount Isa copper smelter is about 0.1 % to 0.4%. Arsenic is a volatile metal, and will partition in the copper smelter between off gases and anode. Most of the volatile arsenic reports to Electrostatic Precipitator (ESP) and Waste Heat Boiler dusts where it will form a re-circulating load within Mount Isa Copper Smelter. Unless arsenic is bled from the smelter circuit, it will build up to a point where both anode quality and smelter hygiene are adversely impacted."

Jan 1, 2011

By J. C. Huyhua

The effect or various oxidants on gold and silver dissolution in thiourea solutions (0.05 M in H2SO4) was studied using the rotating disc technique, a.t 2s c and 600 rpm. These studies were carried out at constant (4:1) initial molar ratio or thiourea to oxidant concentrations, to produce 50 % thiourea. oxidation. The initial dissolution rate of gold was approximately four times higher in the presence. of ferric sulfate (5.37 x 10-3mg cm-2 s-1) than in the presence of hydrogen peroxide (H2O2), potassium persultate (K2S2O3), or monopersulfa.te (KHS06). The dissolution rates for silver were considerably lower than gold for the same oxidants. Oxidation of thiourea in the presence of peroxygen and persulta.te compounds is a. fast reaction and it is completed in less than ten minutes. On the other hand, the oxidation or thiourea with? ferric.sulfate is slow, yielding a second-order reaction rate constant k = 6.09 I mol-1 h-1. Sulfur formation in the ferric thiourea system begins when ferric ion reduction approaches to completion. With hydrogen peroxide, sulfur is observed at lower thiourea concentration than ferric. Suifate. The presence of a large excess or free thiourea i.e., s to 20 % thiourea oxidation) retards sulfur formation and maintains favorable dissolution rates. Finally, carbon-in-leach experiments indicate that thiourea solutions a.re stable for several days, with ferric sulfate or hydrogen peroxide. The dissolution rates of gold and silver doubles in the presence or activated carbon when hydrogen peroxide is used as oxidant.

Jan 1, 1989

By Kun Wang, Xinhui Li, Huaqing Xie, Qingbo Yu, Qin Qin

"Three typical model compounds of bio-oil (ethanol, acetone and phenol) were studied in the steam reforming process for hydrogen production. In the thermodynamic analysis, the three componds showed the similar trends. The hydrogen yields increased with the increase of steam/carbon (S/C) ratios, and the temperatures of the maximum hydrogen yields moved afterward to low temperature zone. However, the hydrogen contents were just about 70%. For improving hydrogen yield, a new system for steam reforming of bio-oil with site CO2 capture was put forward. This system required the catalst with the larger granularity having greater mechanical strength and higher abrasion resistance. So, six Ni-base catalysts loaded on Al2O3 particles prepared were used and among them, Mg-Ni/Co catalyst showed the best catalytic performance. For the simulated bio-oil (the mixture of the compounds), the hydrogen yield can attain 63% with Mg-Ni/Co catalyst with the good stability and regeneration ability.IntroductionCurrently the interest in the use of hydrogen as a clean energy carrier is increasing, and the main way for producing hydrogen is steam reforming of fossil fuels, containing steam reforming of nature gas, naphtha and coal. But this way caused substantial amounts of CO2 emitted, and these sources of hydrogen which are non-renewable energy will eventually be used up [1, 2]. As a kind of renewable energy, biomass is recognized as an attractive alternative to fossil fuels, because of its neutral CO2 emissions [3]. There are mainly two thermochemical processes using biomass to produce hydrogen, gasification and flash pyrolysis followed by steam reforming (SR) of the biooil produced in the flash pryolysis process [4]. The latter was known as one of the most promising and economically viable methods for hydrogen production [5]. In the last decades, the biomass flash pyrolysis technology was adequately developed and fairly mature [6]. But the steam reforming of bio-oil is still at the research stage and yet has been leading to more and more concerns by the researchers. In their research, the catalysts were widely studied and yet mainly were powdery[7-10], and the reactors manily were fixed bed reactors[11-13], readly causing the carbon deposition and the catalyst deactivation, against the continuous running. In this paper, a new systerm was put forward and could realize continuous production of hydrogen, yet needed catalysts with the larger granularity having greater mechanical strength and higher abrasion resistance, as well as powdery CO2 sorbents which mainly calcium oxide based ones.In this paper, the thermodynamic analysis of the steam reforming processes of three typical bio-oil model compounds (ethanol, acetone, phenol) was performed, and the effect of S/C ratio and temperature on the hydrogen yield and the compositions of gaseous products were investigated. Then, a new systerm for steam reforming of bio-oil with site CO2 capture was put forward, and the catalysts with a certain granularity were prepared and studied."

Jan 1, 2014

By Miroslav Raudensky, Kallol Bera, Jaroslav Horsky, Jee G. Chang, Ampere A. Tseng

"A combined experimental and finite element approach to study the local heat transfer coefficient is presented in this paper. The heat transfer coefficients at different cooling regimes in a roll are quantified by an inverse heat conduction technique; the heat transfer phenomena involved are then discussed. A discussion of the application of the heat transfer information found in the present study for better design of a roll cooling system is also included. Finally, an identification of areas where further work is needed is presented.IntroductionIn metal rolling processes, the roll is used as a tool to deform the workpiece at very high speeds. As shown in Fig. 1, the heat transfer phenomena involved in the process are complicated by the interaction between the roll and the strip, mainly including 1) the heat transferred from the workpiece to rolls in the contact regions, 2) the heat created in the interface due to the deformation of the workpiece and the friction between the workpiece and roll, and 3) the heat removed by watercooling as well as the ambient air. All of these transport phenomena occur at extremely high pressure, high speed, and high heat flux; these make the control of the roll temperatures an extremely challenging problem.In hot rolling, proper cooling of rolls can lead not only to improve the roll shape quality by controlling the thermal crown of the roll, but also to extend the roll life by minimizing the thermally induced stresses [1,2]. Also, knowledge of roll temperatures can contribute to insights about the roll/workpiece interfacellubricant behavior, and lead to the desired surface condition of the workpiece. Therefore, adequate roll cooling or control of roll temperatures is of critical concern to mill designers and process engineers. In order to have proper operation of the process, a good understanding of the influence of cooling practices on the roll is essential [3]."

Jan 1, 1994

By Dilip Banerjee

"This paper discusses the Advanced Technology Program (ATP)'s support over the last decade to the development and use of process modeling as a tool to address some of the challenges faced by the U.S. metal casting industries. A particular focus will be given to highlight how process modeling can be used to improve the manufacturability of components needed for high performance and critical applications. The challenges associated with the design and production of thin-walled, cast parts with intricate and complex internal geometries will be discussed. Modeling issues associated with the control of the final grain structure in the solidified parts will also be addressed. This paper will describe the advantages of using appropriate mathematical models for designing new alloys for use in various applications.Finally, the role that ATP has played in uplifting the U.S. technological base through partnerships with industry and academia in high-risk research in order to bring to market new and improved products for the broader benefit of the nation will be discussed.ATP's BackgroundIn the 1980s, U.S. industries were losing market share to low-cost, high-quality manufacturers from Asian countries. Corporate leaders and policy makers determined that in order to sustain and grow market share, U.S. industries needed to improve their competitiveness and productivity through product and process innovation. There was evidence that companies were systematically under-investing in leading-edgetechnologies and failing to complete the development of new technologies [l]. There were also arguments in academic circles that pointed to a potential market failure in the area of early-stage technological developments. These concerns provided impetus for creation of the Advanced Technology Program (ATP) within the National Institute of Standards and Technology through the Omnibus Trade and Competitiveness Act of 1988. Through a rigorously competitive, cost-shared partnership with industry, ATP fosters the development and broad dissemination of high-risk technologies that offer the potential for significant broad-based economic benefits to the United States."

Jan 1, 2004

By Luis W. Pommier

The developed processes, the subject of this paper, extract the hydrocarbons, halogenated organic compounds and metal contaminants from hazardous soils, rendering them non-hazardous and ready to be placed back on the ground. The processes first segregate a non-contaminated fraction from the contaminated soil. This initial task is performed using available minerals processing technology: sizing, gravity separation, magnetic separation, froth flotation, etc. The remaining contaminated fraction, is submitted to two leaching operations for the removal of organic and metal contaminants, whenever both are present or to a single leaching operation if only one type of contaminant is present. The decontaminated soil fraction is mixed with the non-contaminated fraction and is placed back on the ground. The leaching liquors, used at neutral pH, are non- hazardous. After decontamination the liquids are processed to extract the contaminants, now valuable materials, for commercialization. Organic contaminants are removed by distillation of the solvents. The metal contaminants are precipitated in their oxide form. In both cases the regenerated solvents are recycled. The decontamination processes are economically competitive with transportation and disposal of the soils to permitted facilities for hazardous materials, and most importantly the developed processes remove the liabilities from the Responsible Parties. The law establishes that these liabilities do not disappear with either fixation nor with transportation and disposal since the environmental liabilities are of the ? cradle to grave? type.

Jan 1, 1994

By S. q. Honingh, G. Van Weert

Currently produced zinc-enriched blast furnace dust is stored on site at CORUS IJmuiden. To end this practise, a research program was started in 1996. Four technologies were studied: oxidative autoclave leaching in a chloride medium, fluid bed pyrohydrochloridisation (pyrohydrolysis) to yield lead-zinc-free (hematite) calcine, EAF (plasma) smelting/zinc fuming, and incorporation of the dust in 'iron foundry cupola charges. All aim to remove zinc and lead, recycle the iron residue internally, and produce a saleable zinc-lead product.

Jan 1, 2000

By R. M. Taylor

Lime addition to acid mine drainage (AMD) leads to precipitation, predominantly of metal hydroxides and calcium sulfate, and is the benchmark for remediation by precipitation. Geo2 Limited of Melbourne, Australia has developed and patented a novel alternative precipitation scheme based on the formation of mixed valency, M(I1)-M(III), hydroxide sulfate salts. When the composition of AMD is appropriate, the Green Precipitate Process provides a useful and more effective alternative to conventional liming. The characteristics and utility of the Green Precipitate Process are described in terms of the underlying chemistry, and a case study where the Green Precipitate process outperforms conventional liming. A mobile pilot pipe reactor rig which was built by Geo2 to demonstrate the process, and used successfully in both Australia and the United States, is described.

Jan 1, 1998

By J. D. Sloop

This paper discusses the current state of EAF dust recycling at AmeriSteel's Dust Processing Division in Jackson, Tennessee. Included are a brief history of the plant, a description of the facility, a description of the process, and operating data.

Jan 1, 2000

By Benjamin P. Hay

Complexation of a metal ion to a ligand often results in structural changes that introduce steric strain within the ligand. A design criterior:1 for ligands that will complex metal ions more strongly is to choose Iigar:1d architecture, that minimizes this strain. This paper describes how molecular mechanics models can be used to define the degree of ligand binding site organization in terms of' ,strain energies associated with conformational reorganization and distortion of the binding conformer. This approach yields a method to predict how modifications to ligand structure will affect metal binding affinity.

Jan 1, 1999