Search Documents

By C. A. Pickles

Microwave processing is a relatively new technology that has been successfully applied in a number of industries. However, in the field of metal extraction, there is a paucity of success, despite considerable hype in the early years. Increased reaction rates, lowered reaction temperatures and higher energy efficiencies were some of the advantages claimed. Even with over almost two decades of research and some pilot plant studies, microwave metal extraction remains essentially a laboratory technique. In this paper, the research performed over the last few decades will be reviewed and some reasons for the lack of success in developing microwave metal extraction processes will be discussed. Based on the knowledge gained from these experiences, a more informed view of microwave heating can lead to the realization that there is still some untapped potential for this heating technique in metal extraction processes.

By Mark H. Hashiguchi

Examination of tensile bar surfaces shortly after destructive testing was conducted to search for clues that would aid in optimization of mechanical properties, especially tensile strength, yield strength and elongation to fracture. Cu-Ni-Si-Cr alloy bars in the as-cast, forged, rolled and extruded conditions were examined. Low ductility bars (<4% Elongation) showed dramatically different features than the fracture surfaces of high strength - high ductility bars (7 to 10% Elongation). Analysis of the fracture surfaces at 15X to 2000X and use of Energy-Dispersive X-Ray Spectroscopy (EDS) identified Ni-Si and Ni-Si-Cr precipitates of varying sizes and morphologies. Thermo-mechanical processing techniques to control the size and distribution of these precipitates show promise in improving the properties and performance of this alloy system and appear to correlate with improvements in the fracture surface morphology.

Jan 1, 2008

By R. Tunold, Y. J. Zhang

"The cathodic kinetics of aluminum deposition from aluminum chloridealkali chloride melts was studied by use of electro-cnemical transient techniques at 700 °C. Aluminum deposited as an insoluble product on a glassy carbon electrode and as a partly soluble product on a tungsten electrode. The deposition was found to be a simple diffusion controlled process involving the exchange of three electrons. The diffusion coefficient of aluminum chloride was calculated - 4.sx10-s cm2 ·S-I in AlCl3 -NaCl-LiCl melts and 2.6x10-s cm2 ·S-' in AlCl3 -NaCl-KCl melts. For AlCl3 -NaCl-CsCl system the diffusion coefficient exhibited some uncertainty due to nucleation. The determined rate constant of aluminum deposition reaction was on the order of 10-' -10-2 cm'S:' Constant potential electrolysis was carried out. TiB2 was well wetted by aluminum. The species of melts penetrated into graphite and glassy carbon but not into tungsten. The diffusion coefficient of species in glassy carbon was evaluated.IntroductionAluminum chloride electrolysis is attractive for its power saving of 30%. Different process to circumvent the conventional chlorization to obtain aluminum chloride economically, such as directly chlorizating mixture of Al~03 and C in a cell with A-shaped laminated bipolar electrodes by rising chlorine (1), or by use of a composite anode (2), will promote the electrolysis technology to be realized industrially. With the appearance of the Alcoa process periodically there are studies on the kinetics of aluminum deposition. Some discrepancies seem to exist on the mechanism of aluminum deposition. Borne studies (3,4,5) showed that the deposition of aluminum was hindered by diffusion process in the melts. M.Gabco et a1. (6) claimed a preceding dissociation of a complex being the rate controlled step. This paper presents our results on the mechanism of aluminum deposition from the study by use of transient techniques and some results from constant potential electrolysis."

Jan 1, 1988

By Ruixuan Zhang, Yan Li, Shusen Cheng

The measurement of raceway temperature in the blast furnace is a critical issue, which is very significant for judgment of, prediction and diagnosis of the racewa yburning state. This paper deals with mathematical models by Monte Carlo method to approximately simulate the radiation heat transfer in the race-way and establish matrix equations using CCD cameras, which are solved to obtain the three-dimensional temperature field. Due to the existence of fluctuation error, CCD camera measurement error and others,this is analyzed and random error is added in the measurement data to demonstrate the effectiveness and stability of the reconstructed temperature field. The results show that the reconstructed three-dimensional temperature field of the raceway is very close to the exact temperature.

Mar 1, 2017

By Ph. Cauwe

This paper presents the experience that NESA and MECHIM have gained about recovery of non ferrous and precious metals from complex sulfide materials. Processed materials are from natural deposits or metallurgical by-products or residues. Roasting of these materials is closely related to the pyro or hydrometallurgical processes used downstream of the roasting. Conditions of a first step of roasting the SELECTIVE ROASTING, are analyzed and explained. The roasted products so obtained are characterised by an extended elimination of volatile sulfides (AS, Bi, Sb, Sn, Pb, Hg, ?? ) and are readily available for the pyrometallurgical recovery of non ferrous and precious metals. After the SELECTIVE ROASTING, thanks to. the high porosity obtained in the "selective calcine", the SULFATE ROASTING is per-formed in excellent conditions. Hydrometallurgical tests performed for the final calcine show a high recovery of non ferrous and precious? metals and require only simple and well known processes. Many experimental and commercial data are given.

Jan 1, 1983

By Tina Maniatis

Applied Biosciences has developed a biological technology for removal of arsenic, nitrate, selenium, and other metals from mining and industrial waste waters.The ABMet® technology was implemented at a closed gold mine site in Canada for removing arsenic from tailings pond water. The system included six bioreactors that began treating water in the spring of 2004. Design criteria incorporated a maximum flow of 567 L/min (150 gallons per minute) and water temperatures ranging from 10°C to 15°C. Influent arsenic concentrations range from 0.5 mg/L to 1.5 mg/L. The ABMet® technology consistently removes arsenic to below detection limits (0.02 mg/L). Data from the full scale system will be presented, as well as regulatory requirements and site specific challenges. Keywords: Arsenic, Sulfate Reduction, Metal Sulfide Precipitate, Biological Water Treatment

Jan 1, 2005

By Peter Bates

"HIsmelt has faced and overcome many challenges in the understanding and development of injection technologies that satisfy process and engineering requirements for further scale up to a commercial plant.An overview of the design basis of bottom and top injection systems with plant results are described in this paper.IntroductionAn appropriate way to introduce this paper is to initially reflect on the genesis of the HIsmelt Process.It is appropriate that Professor Womer is the one we are honouring as it can be claimed that by the involvement of CRA in the WORCRA process that the concepts for irijection systems in iron and steel pyrometallurgical processes achieved significant attention by the company. The development of water cooled injection lances and their application injecting solids and gases with success was certainly a pre-cursor to the development of other injection systems commonly used today in arc furnaces and for top injection at HIsmelt.HistOrically it was the work of Savard and Lee in Canada with shrouded tuyeres and the subsequent commercialisation of this technology at the Maxhiitte Steelworks spawning the suite of bottom oxygen blown process as known as QBOP; OBM and the subsequent combined blowing process such as KOBM that first commercially succeeded in injecting solids under a molten metal bath. The next progressive step from the injection of calcined lime in the technology development was the injection of coal for coal gasification as developed by Klöckner technologies being called KG, KSG and KMS and also the injection of coal for increased scrap melting.A paradigm shift in thought process to leap from steelmaking and coal gasification to direct smelting by injecting coal and iron ore into a molten metal bath in the correct stoichiometric ratio to maintain the bath at a constant temperature and carbon level was the true genesis .of HIsmelt.A good overview of the state of the art of tuyere type injection technology is given in Ref. 1."

Jan 1, 1996

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim&apos; at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By Xia Lou, Hossein Dashti

Gas hydrates technology has been considered as an alternative method for carbon dioxide (CO2) separation. A wide range of studies have been reported in the past decade on the improvement of the separation efficiency by using chemical additives. While most of these studies have shown improved kinetics, thermodynamics and/or separation efficiency at the laboratory scale, there has been no quantitative analysis of the energy consumption for viable industrial applications. Comparison of the effectiveness of the chemical additives from separate studies or groups also is impossible. The present work is focused on the modelling of the hydrate-based CO2 separation process and provides a quantitative approach that is new in its analysis of the effectiveness of chemical additives in relation to the energy required and the kinetic parameters involved in the process.

Mar 1, 2018

By Xie Zhang, Jiang Diao, Xiaojun Li, Bing Xie

"Vanadium is widely utilized as an important element to improve the quality of alloyed steels in iron and steel industry. Moreover, the crystallization process of V-containing spinels plays a significant role due to the aim of achieving a fairly larger size of spinel crystals in vanadium extraction. Thus, a comprehensive exploration and discussion on the competitive precipitation and growth of vanadium, chromium and titanium spinel crystals in vanadium slag during a cooling process were carried out in the present study on the basis of a crystallization kinetic model. To be more specific, the abilities of forming crystal, precipitation order and suitable temperature range for crystallization of the three kinds of spinels were discussed with both theoretical and experimental methods.IntroductionVanadium is an important element which is used almost exclusively in ferrous and non-ferrous alloys due to its excellent physical properties such as high tensile strength, hardness, and fatigue resistance [1]. Various kinds of processes of vanadium extraction from V-containing hot metal are available at present. However, only four processes which are the Highveld process (South Africa), the Pan-steel process (China), the NTMK duplex process (Russia) and the New Zealand steel process (New Zealand) take the dominant positions [2, 3]. Although the type of reactor and the initial vanadium content in hot metal are different in these techniques, they share the same principle that vanadium is oxidized by oxygen into vanadium slag."

Jan 1, 2012

By Oleg Ostrovski

Industrial pyrometallurgical processes in ferrous metallurgy are based on carbothermal reduction of metal oxides. Carbothermal reduction of stable oxides requires high temperatures. Lowtemperature reduction can be implemented by using methane-containing gas with high carbon activity, or by carbothermal reduction under reduced CO partial pressure. Under standard conditions, methane is thermodynamically unstable above 550 °C and decomposes to solid carbon and hydrogen. At appropriate CH4/H2 ratio and temperature, carbon activity in the methane-containing gas phase can be well above unity relative to graphite, which provides favorable thermodynamic conditions for reduction. To maintain these conditions, the rate of reduction/carburisation should be higher than the rate of solid carbon deposition. The paper discusses reduction of pure manganese and chromium oxides at relatively low temperatures, and constraints in reduction of manganese and chromium ores. Reduction of metal oxides by carbon in hydrogen as an alternative use of natural gas is also discussed.

Jan 1, 2014

By Edwin de Jesús Deveaux

After 32 years of operations beneficiating lateritic nickel ore in a fully integrated pyrometallurgical complex, Falconbridge Dominicana (FALCONDO), situated at Bonao and La Vega Provinces, Dominican Republic, has become profitable with one of the lowest nickel grade content processing plants in the world, and literally without any by-product (granulated slag, will be utilized in the future as a post-processing subproduct). To December 2002, mineral reserves were 64.1 million tonnes containing laterite grading as low as 1.15 % Ni when full dilution is applied. At a cut-off grade of 1.20% Ni, the reserves will provide 15-20 years of production. The mineralized thickness over the seven active deposits averages 6 m. Development of very selective and unique mining practices, together with improvements in the process plant, are key to achieving the production goal (30 kt Ni/yr) and to meet the quality standards for the ferronickel produced. Keywords: Laterites, grade control, mining methods, environment

Jan 1, 2004

By Z. B. Moukhametshina

The process of various zirconium alloys iodination by the iodine vapor was investigated. The nature of impurities, conditions of iodination, iodine flow rate, and zirconium tetraiodide condensation rate effect on the metal impurities transfer process was analyzed, both qualitative and quantitative correlations were established. Impurities were classified according their transfer extent. Another classification of impurities transport dependence on iodination process temperature was also offered. Obtained results were compared with impurities transport data in the process of iodide refining available in literature. Some impurities transport mechanisins and iodide-refined metals improvement possibility by means of iodination conditions control were discussed.

Jan 1, 1997

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998

By Paul C. Turner

In 1998, approximately 57,000 tons of titanium metal was consumed in the form of mill products (1). Only about 5% of the 4 million tons of titanium minerals consumed each year is used to produce titanium metal, with the remainder primarily used to produce titanium dioxide pigment. Titanium metal production is primarily based on the direct chlorination of rutile to produce titanium tetrachloride, which is then reduced to metal using the Kroll magnesium reduction process. The use of titanium is tied to its high strength-to-weight ratio and corrosion resistance. Aerospace is the largest application for titanium, and titanium cost has prevented its use in non-aerospace applications including the automotive and heavy vehicle industries.

Jan 1, 2001

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By S. J. Thiele, T. Newton, W. Magalhäes, T. Takayama, J. Welsh

Companhia Paraibuna de Metais (CPM) is presently pursuing a zinc production expansion project. Besides increasing production, the goal of the project is to address existing problems while providing a platform for a proposed twofold increase in production in 2003/2004. Therefore, the current expansion strategy was formulated to address present and future requirements. Computer simulation modeling and full scale plant testing are being used to generate data to optimize the operating conditions and to perform a sensitivity analysis. The initial phase of the project, which will boost CPM's capacity to 86,000 t/y of marketable zinc, is to be completed in September 2000.

Jan 1, 2000

By Mehmet Bu daycı, Onuralp Yücel, Ahmet Turan, Murat Alkan

In this study, iron based alloys (Fe, Fe-Cr-Ni-Mo, etc.) were produced by using metallothermic methods starting from Mill Scales obtained continuous casting processes. During the process, the combustion was realized by ignition and the produced wave propagates throughout the reactant mixture yielding the desired product. In this work, Mill scale used as an iron source, which includes +2, +3 values iron oxides. Aluminum, Magnesium and Silicon were used as reductants. In these metallothermic experiments, different ratios of reductants were examined, and their effects on the metal recovery and alloy compositions were investigated. The samples were characterized by using chemical analysis (AAS), XRD and XRF techniques.

Jan 1, 2016

By A. E. Torma

In recent years the copper industry has gained considerable economic stability. An essential part of this industrial wealth is attributable to the successful application of bio-mediated heap and dump leaching techniques in the recovery of copper from low-grade resources. This study evaluated the leachability of a chalcopyrite conlentrate using naturally occurring mixed culture of predominantly Thiobacillusferrooxidans and Thiobacillus thiooxidans. For the effects-of pulp density, the overall reaction rate constant (k) and the order of reaction (n) have been determined to be 1.93 h-1 and 1.36, respectively. Cyclic voltammetric measurements revealed that intermediate reactions are involved in the chalcopyrite oxidation. Using the Price approach, it was shown that the dissolution of chalcopyrite is solid state diffusion controlled.

Jan 1, 1992

By Yimin Ruan

"An inverse design method is developed to obtain the optimal cooling conditions for the continuous quenching of precipitation hardenable sheet alloys to achieve the required yield strength. The yield strength of a precipitation hardenable alloy is obtained by allowing solute to enter into solid solution at a proper temperature and rapidly cooling the alloy to retain the solute in the solid solution. An aging process may be needed for the alloy to develop the final mechanical properties.The objective of the design is to optimize the quenching process so that the required yield strength can be achieved. With the inverse design method, the required yield strength is specified and the sheet thermal profile at the exit of the quenching chamber can also be specified. The conjugate gradient method is used to optimize the cooling boundary condition during quenching. The adjoint system is developed to compute the gradient of the objective functional. An aluminum sheet quenching problem is presented to demonstrate feasibility of the inverse design method.IntroductionQuenching is a critical step in metal production to achieve desired material properties, such as yield strength, hardness, etc., for precipitation hardenable alloys. In most cases, rapid quenching from the solution heat treatment temperature is necessary to obtain the required material properties, but rapid quenching may cause other problems such as excessive distortions of the quenched materials.In a solution heat treatment, the alloy is heated to a suitable temperature, held at that temperature to allow the soluble alloying elements to enter into the solid solution, and cooled rapidly (quenching) to retain the alloy elements in the solid solution. An aging process, which controls precipitation of fine particles at room (natural aging) or elevated temperatures (artificial aging), is generally followed after the quenching process to develop the final mechanical properties of the heat treated alloys."

Jan 1, 1998