Search Documents

By Greg Rappard, Francois Holowenczak, James Rickard

The King George V (KGV) Shaft forms part of MTR Corporation Limited (MTRCL) Works Contract 703 extension of the underground West Island Line on Hong Kong Island. The Shaft and the associated adit was the sole access to excavate the running tunnels. Originally during the Detailed Design stage, it was concluded that blasting was not feasible at the KGV Shaft due to the close proximity of sensitive receivers in the form of residential buildings, electrical cables and hospitals. As a result, the Contractor planned to excavate the Shaft using mechanical means with a programme time of seven months. The Contractor appointed a Sub-contractor to analyse the feasibility of excavating the Shaft by blasting. The Sub-contractor reviewed the proposal and recommended the use of an innovative blasting technique that had never been previously employed in Hong Kong. The Sub-contractor recommended the Shaft be blasted using DetNet electronic delay detonator technology, manufactured by AEL Mining Services in South Africa, with an initial 1.5m depth of water ballast covering the blast face. The electronic delay detonators provided initiation accuracy to ensure there would be no overlap between sequentially detonating blastholes. The water ballast makes use of the effect of energy lost through the shock front causing the water to break up into droplets creating a spray dome resulting in the attenuation of the energy imparted into the surrounding rock mass. Various tests have demonstrated that both the maximum overpressure and impulse density are significantly reduced when water of a minimum depth is in direct contact with detonating explosives. This innovative blasting technique reduced the excavation programme by three months, saved HK$5 million in direct costs and totally mitigated the impacts on the public and other stakeholders nearby the KGV Shaft. Peak Particle Velocities (vibrations) rarely exceeded 2-3mm/sec (0.08-0.12in/sec) at a distance of 30-40m (98-131ft) from the blast location and air overpressure levels were reduced below the Hong Kong target level of 120dBL. In total, 24 blasts were fired with an average advance of 1.6m (5.25ft) with an average powder factor of 2.03kg/m3 (0.127lb/ft3) to 1.84 kg/m3 (0.114lb/ft3). The initiation pattern had 5ms between sequentially detonating blastholes and 20ms between adjoining rings.

Jan 1, 2013

By L. Arnberg, E. Ott

The microstructure of ferrosilicon is important since it controls the disintegration of the material during crushing and thus the generation of fines. Therefore a study of the microstructure formation during solidification of pure FeSi(75wt%Si) and FeSi(75wt%Si) containing 1.2wt%Al and 0.2wt%Ca has been initiated. The material has been cast into rods of 8mm diameter, which have been remolten by induction heating and directionally solidified in a Bridgman apparatus. This allows the temperature gradient and the growth rate to be controlled independently. The temperature history during solidification has been recorded by a thermocouple in the melt. Growth rates have been varied between 5 and 400µms-1 and temperature gradients between 3 and 14°Kmm-1. The microstructures show a large dependence on the solidification conditions. The crack formation in the alloys has been studied and found to be strongly related to the microstructure.

Jan 1, 2004

By D. Large, M. H. Davies, B. Driedrichs, U. Matzander

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A prototype high-resolution electromagnetic system, based on the theory of controlled-source magnetotellurics, was developed. The electrical source field is fed into the earth by dipoles at preselected frequencies and a multi-channel receiver measures five electric and three orthogonal magnetic fields. Suitable mapping algorithms and spatial filters are applied to the data and a new technique permits calibration during measurement. The system was field tested over a blind orebody, at 250-550 m depth, in the Aguas Tenidas area of the Iberian Pyrite Belt. Ten lines totalling 12 000 m of profile length were completed in seven days and the orebody was identified. Tests in the Irish Midlands suffered from strong electromagnetic interference of cultural origin

Jun 21, 1905

By Matthew Kowalczyk, Steve Bloomer, Peter Kowalczyk

"Mineral deposits found near seafloor hydrothermal venting are of great economic interest. Valuable metals such as gold, copper, zinc, and other polymetallic sulfides are found in appreciable grades in seafloor massive sulfide (SMS) deposits associated with these vents. For mapping these deposits, electromagnetic prospecting is one geophysical method that is very useful because copper/gold rich deposits are highly conductive.Ocean Floor Geophysics (OFG) in 2008 developed the first EM system to successfully map the limits of conductive mineralization in a survey at the Solwara 1 deposit (Kowalczyk, 2008). Since then, towed coincident loop time domain systems have been developed by Waseda University (Nakayama and Saito, 2016) and have successfully detected known mineralization buried at 30m depth. Using a deep tow controlled source electromagnetic (CSEM) array, very clear anomalies have been measured (Murton, 2017) over known mineralization at the TAG field on the mid-Atlantic ridge.In 2014 and 2015, OFG partnered with Fukada Salvage and Marine Co. Ltd. and the Scripps Institution of Oceanography to map methane hydrate deposits off the coast of Japan using a towed controlled source electromagnetic (CSEM) system developed by Scripps. These hydrate deposits are resistive targets, and the Scripps system successfully mapped subsurface electrical resistivity distributions to depths of several 100 metres below the seafloor. OFG is attempting to extend the Scripps CSEM technology to map subsurface conductive SMS deposits to a similar range of depths below the seafloor."

Jan 1, 2017

By Toshiaki Nakai, Kunihiko Takeda, Kimio Imaizumi, Hiroaki Shirasaka

"The new type of nano-porous silica particle was considered to be constructed by the spinodal decomposition-type process which was found to have narrower pores than those of conventional porous silica prepared from boron silicate or ""Shirasu"" balloon. Nano-porous silica particles were fabricated by the calcination of silica gel mixed with well-dispersed complex salts composed of phosphorous and molybdenum compounds. Both silica and inorganic salts were not perfectly dissolved in the suspension solution. After removing of the water, the silica-inorganic salts complex was volatized and successively calcinated at a temperature ranging from 650 °C to 800 °C. Then, the inorganic salts were removed by dissolving in hot water. Other inorganic salts such as potassium halides were also found to be effective as a pore-size controller.IntroductionControl of structure has an important role in the field of industry as well as in the separation and purification technology for metals and organic syntheses. Many studies on the control of material structures have been reported regarding porous materials with pores ranging from nanometer to micrometer scale. 1 ) One example is zeolite as a naturally yielded porous inorganic material. Various types of synthetic zeolites have been studied as ""molecular sieve"" materials with ordinary pore-size of less than one nanometer. In 1992, crystalline meso-porous material with a large surface area named MCM-41 was synthesized through the use of template synthesis. 2) In direct relation to our study, amorphous borate glass having 4 to 100 nm of fine pores known as Corning glass 3l or SiO2-Al2OrB2O 3-CaO porous glass having large pore dispersity ranging from 4 to 10,000 nm have been reported. 4 ) S) 6 ) Some examples of several reported studies are as follows: phase-separated porous glass consisting of B2OrAl2O3-ZrO2-RO-R2O complex oxide 7 ) glass with finer pore induced from hydrolysis of silane alkoxide, porous material attained by condensation polymerization through the use of sol-gel process 8), alumina meso-porous material 9 ) 10), silica-zirconia material 11), carbon porous material 12), etc.."

Jan 1, 2000

By R Wing, D Corkery

"Several mines in the region of Sudbury, Ontario, occur in or near populated areas. In anattempt to examine the effects of environmental changes and blast induced vibrations onhomes in the area, a monitoring study was conceived. The study was conducted fromNovember 1990 to May 1991 in homes located near the 880 Stope at INCO Ltd.'s CopperCliff South Mine."

Jan 1, 1993

By Raden Haris Handayana, Jihan Farhan Lubis, Milia Putri, Tengku Deli Hamonangan Hasibuan, Sani Salahudin

An environmental issue that must be controlled from coal overburden blasting near the structure is ground vibration. Damaging ground vibration is the effect exerted from residual energy from blasting that does not work to fracture the rocks. Sebuku Tanjung Coal is a coal mining that operates T3 Pit adjacent to the High Voltage Tower. This structure is included in the Class 5 building with a maximum Peak Particle Velocity (PPV) of 40 mm/s. The shortest distance from the blasting location to the structure is 105 m. The initiation system used is electronic detonators combinate with emulsion as an explosives type. In Indonesia, the government regulated vibration limitation on SNI 7571:2010. The blast outcomes targeted are PPV below 40 mm/s, fragmentation size <80 cm for Excavator Komatsu PC-2000, and digging time <12 seconds. In this paper, the blast design was engineered by conducting Signature Hole Analysis for optimizing delay timing configuration and Scale Distance regression analysis to determine optimum charge weight per delay at the blast site. PPV results from 30 blastings achieved 100% below 40 mm/s with the range of about 1.773-30.250 mm/s. The deviation between PPV prediction to PPV actual is less than ±18% which provides the blasting with electronic detonator resulting in good PPV prediction for controlling vibration. The average fragmentation size (D80) is 55.81 cm in the 1st layer and 54.81 cm in the 2nd layer. The average digging time is 10.30 seconds in the 1st layer and 10.12 seconds in the 2nd layer.

Feb 6, 2023

By Anil Mahyera

Under contract to the Bureau of Mines, a roofbolting machine has been developed which will: control torque on the bolthead to within 4 percent of a set point, control thrust to a low level (150 lbf), and implement a tightening method to minimize variability due to bolt tension decay of a group of bolts caused by differing anchor creep rates. This bolter was used to determine bolthead and thread friction factors, and to determine the effect of adding a hardened washer to the bolt assembly on the uniformity of bolt tension in the laboratory and field. Recommendations for torquing speed, bolt lubrication, use of hardened washers, and thrust level on the bolthead are made. The relationship of this system to Improved roof control is discussed, along with additional work that remains to be performed. Patent Notice Patents are pending which protect the hardware and methods of controlling tension decay as discussed in this paper.

Jan 1, 1981

By Paulo José Costa Couceiro Junior, Manuel Lopez Cano

The biggest Port of Latin America - the Santos Port in São Paulo, Brazil - has been drilled and blasted by controlled underwater techniques in order to remove around 40,000 m3 (52,318 cubic yard) of rock divided in two outcrop rocks: Teffé and Itapema. Underwater pumped explosive, in combination with small cartridges areas, was successfully used in order to reach a target depth of -15m (-49 ft) and a width of 220m (722 ft) in the navigation channel. It was the first time that a pumped explosive was used in underwater blasting in Brazil and it represents a historic benchmark for projects of this kind in this country. The main challenges faced in this project include the control of the ground vibration, due to the necessity to carry out detonations 40m (131 ft) away from the quay wall - where the passenger terminal and the 80 year-old warehouse were located – and the rush schedule available, in order to finish the underwater drilling and blasting phase before the coming cruise season. Therefore, the perfect combination of an ideal pumped product with an effective pumping system has permitted to carry out the project in a record of less time than 3 months (against to the original expected time of 18 months), with all vibration events under control as result of the special ground vibration program carried out.

Jan 1, 2016

By Wong KY, Woodcock JT

Previous results have shown how con- trolled-potential sulphidization (CPS) can give improved metallurgy during rougher flo- tation of mixed oxide-sulphide copper ores. Results in this paper, using different samples and different equipment, confirm the previous results and extend the application of CPS to cleaner flotation. By using CPS, faster flotation of copper minerals (chalcocite and malachite) from clay was obtained in roughing and cleaning, and improved concentrate grades and recoveries were achieved over those by conventional manual control. The optimum sulphidizing potential (i.e. the potential of a sulphide ion-selective electrode versus a saturated calomel electrode) was -500 mV, and could be controlled to ¦5 mV, during four rougher- scavenger and three cleaner-re cleaner stages. This optimum gives the best balance between copper recovery, concentrate grade, and sodium sulphide consumption. Five cleaning circuits and five ore com- posites of different composition (0.55-1.50 per cent Cu) were examined as well as the effect of feed size and pulp density. Better results were obtained at 20 per cent solids in a Denver cell than at 33 per cent solids in an Agitair cell; this may have been related to the high clay content of the ore. Commercial equipment for pilot plant or full-scale plant application of CPS is cur- rently being developed.

Jan 1, 1986

To allow the controlled yielding of mine walls in order to reduce rock-burst hazards and reduce maintenance caused by excessive squeezing forces. Approach Rock bolts that elongate and continue to sustain a load, have been fabricated and tested. This device is an adoption of a concept originally developed in South Africa for use where unusually adverse conditions may warrant the added cost. How It Works A coupling in the rock bolt allows controlled elongation if the load increases beyond the bolt&apos;s design strength. (The load can build up either slowly, as during heaving, or rapidly, as before a rock burst.) The elon¬gation of one or more rock bolts surrounding a mine opening, allows the rock to move from its original position to c new position in a controlled manner. This movement relieves the rock stresses, and the mine opening reaches a new state of equilibrium. The elongatible coupling of the rock bolt consists of a

Jan 1, 1977

Provide the technology to remotely control a thin¬-seam continuous mining machine from a safe location hundreds of feet outby the working face in an underground room-and-pillar mine. Background and Approach Hard-wired or radio remote control of continuous mining machine has been commercially available since the early 1970&apos;s. This type of remote control, in low and high coal seams, situates the machine operator offboard, but within direct view of the underground coal face, Although positioned under supported roof, the operator can still be exposed to face area hazards that include roof-rib falls, dust, methane explosions, and equipment congestion. The U.S. Bureau of Mines approach has been to put the operator into a protected compartment at a location away from the working face. Since 1979, the Bureau has investigated innovative methods to better protect face area workers in under¬ground room-and-pillar mines. In 1989, the Bureau demonstrated an offboard, computer-based remote con¬trol system in a West Virginia highwall mining operation that stationed the operator hundreds of feet away from the working face. In late 1992, much of this technology, plus improvements, Was used to demonstrate, on the surface, how a thin-scam continuous mining machine could be remotely controlled 200 feet from the machine in a 36-inch working height.

Jan 1, 1992

By William H. Schiffbauer, William D. Mayercheck, August J. Kwitowski

This report summarizes work sponsored by the Bureau of Mines in the development of a remote operating system (ROS) for controllng a thin-seam continuous miner (TSCM) 500 feet or more distant from the extraction face. Detail s are provided on ROS subsystems including the continuous miner, video equipment, controls and displays, the electronic control system, and the operator station.

By R. Bruce Sheibach

The Picher Mining District, located principally in north-eastern Oklahoma, was one of the world&apos;s largest lead-zinc mining areas during its 55 year life. The field covers an area of approximately 72 square miles (186 km.-); an estimated 1.6 x [103 yds3 of material (1.22 x 103m3)] worth in excess of one billion dollars, has been mined. Mining activities were typified by surface exploratory drilling identifying ore distribution and extension of underground workings to the lead and zinc deposits outlined. Exploration holes were either left unplugged or plugged at the surface with a section of a telephone pole. Low grade ore and waste rock were discarded in mined out portions of drifts. These waste piles containing pyrite and marquisette were left underground and oxidized during the many years of active mining. Upon cessation of mining activities in the mid-1960&apos;s, the drifts and shafts of the abandoned workings began to flood as the cone of depression filled in, leading to the dissolution of the oxidized sulfides and the formation of large volumes of acid mine water in the mined out openings. The resulting poor quality water, with high concentrations of cadmium, iron, lead and zinc, began discharging at the surface in 1979. Contamination of the underlying aquifer supplying local residents was first detected on a localized scale in 1980. The present surface water and ground water contamination have lead to the area being classified as one of the top ten hazardous waste sites in the U.S. by the EPA under the superfund program.

Jan 1, 1982

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes. Accurately capturing and modeling this geology is the key to controlling high air blast. 3D modeling and profiling by drone is the solution to understanding accurate face profiles and real minimum burdens. Using 18 months of blasting data and air blast results to establish a baseline, the comparisons between blasts designed with 2D profiling and blasts designed with drone 3D profiling show improvement in air blast levels. Additionally, shots with completed drilling were drone profiled to understand precise amounts of burden for each borehole. This 'audit' of a blast allows for custom loading of explosives, accommodating the amount of burden present on the blast face. 3Dprofiling is not a new tool in the blasting industry, but a drone alleviates some of the restrictions ground systems face. Controlling and managing air blast, as it pertains to face burdens, requires an understanding of those burdens from all angles. A drone provides that distinct level of insight. The results of this study indicate that drone profiling is managing the customer's air blast readings, allowing the customer to maintain their license to operate within the community.

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Steven E. Mischler

The exposure of mine workers to diesel particulate matter (DPM) and gases is an issue of great concern to the underground mining community in the United States. Approximately 30,000 underground miners are potentially exposed to high concentrations of DPM. In January of 2001, the U.S. Mine Safety and Health Administration (MSHA) promulgated rules setting compliance standards for both underground coal and metal / nonmetal mine workers. As industry works to achieve compliance with these standards, mine operators are looking for feasible methods for reducing DPM concentrations in their mines. In addition, the industry needs methods to accurately measure DPM to ensure that the control strategies they adopt are working successfully. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducts research to evaluate control technologies and monitoring instrumentation that can be used to reduce the diesel particulate matter (DPM) exposure of mine workers. An overview of the strategies being utilized in underground US mines to reduce DPM concentrations will be presented. Also, updates on the development of diesel monitoring instruments such as the continuous elemental carbon monitor or the Personal Dust Monitor for DPM measurement will be provided.

Jan 1, 2010

By Calvin J. Konya

Backbreak behind the last row of boreholes can be a significant problem for blasting operations. Backbreak will interfere with the proper drilling and execution of the subsequent shot and can produce well defined boulders, which will not be broken by the subsequent shot. In order to determine the effect of timing on backbreak, a full scale blast with 6 1/2 inch boreholes was used to test the effects of timing. The test site was a quarry which had suffered from severe backbreak regardless of the blasting pattern or explosive used. One half of the production blast was loaded and initiated using the current technology at the quarry, the other half of the blast was deliberately timed in such a manner as to minimize backbreak. The timing was such to allow for ground movement in one row before the subsequent row fired. The test results proved that the amount of backbreak and flyrock could definitely be controlled with the selection of the proper borehole timing.

Jan 1, 1987

By D. R. Zuchelli

The purpose of wrapping ball mills with thermal/acoustic blankets is twofold: 1) to maintain the desired temperature inside the mill, and 2) to reduce the sound emanating from the mill. This field case study focuses solely on the latter, evaluating and documenting the sound level reduction attributed to the installation of the blankets on ball mills and its potential to reduce the noise dose experienced by the process attendant. One of the three ball mills had already been treated (baseline) before the evaluation started. However, treating the remaining two mills still proved to be very effective, further reducing ball mill noise in the near field by as much as 10.0 dBA and producing far field noise reductions of 3.0 dBA or greater, extending as far as 35 feet from the mills and to the floor above. The model developed from the survey data shows that a process attendant spending a substantial portion of a shift in the mill building will experience a significant reduction in overall noise dose.

Jan 1, 2010

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016