Search Documents

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By D. C. Holloway

Ceramic projectiles made from 94% to 99% alumina with a nominal mass of 3.1 gms were fired into granite blocks. The average compressive strength of the ceramic was 800 MPa and that of the rock was 135 MPa. Flat, ogive, conical and pyramidal nose shapes were evaluated at velocities ranging from 450 to 1400 m/sec. It was found that the conical and pyramidal nose shapes at the higher velocities did a significant amount of damage to the rock. On the average, they removed 10 5mm3 of rock and were six and ten times better than the flat and ogive nose shapes. It was also observed that increases in volume occur in discrete steps. This process is highly dependent on the ability of the projectile to penetrate the rock.

Jan 1, 1984

By C. J. Monahan

INTRODUCTION With the introduction of large diameter hole drilling to underground mining, a need for the development and utilization of new blasting technology has arisen. This new technology has resulted in more efficient blasting and in easier and cheaper mining. The application of spherical charges to the crater blasting method is an im¬portant part of this technology. Spherical charges, or their geometric equivalent, make for highly efficient use of explosives in the cratering application. Their geo¬metrical configuration, normally a length :diameter ra¬tio of <6:1, limits their charge weight size. For exam¬ple in a 165-mm (61/2-in.) hole a spherical charge weighs approximately 34 kg (75 lb). These dimensional and weight restrictions require careful engineering design and control in the production application. Strathcona mine, a large tonnage mechanized cut¬and-fill and blasthole stoping operation located on the north rim of the Sudbury Basin, has successfully em¬ployed the crater blasting method in production blasting for the past two and a half years (as of 1979). As a result, this method, using spherical charges, has made possible the development and implementation of a verti¬cal retreat blasthole mining method which is being used for rib pillar recovery. The crater method used at Strathcona essentially in¬volves blasting off horizontal slices of ore into an under¬cut while retreating vertically to the pillar overcut elevation. Loading and priming of the holes is achieved from the overcut and the blasted muck is recovered by load¬haul-dump (LHD) units through a drawpoint system. Valuable experience on the behavior and performance of explosives in large diameter holes has been gained in both the operating and engineering fields from the appli¬cation of this blasting method. It has been used in drop raising and is currently being evaluated for use in pri¬mary stoping operations. Also, serious consideration is being given to its use for the recovery of post pillars in mined-out and backfilled cut and fill stopes. The method has significant advantages over conven¬tional methods of pillar recovery from economic, ground control, and safety points of view. These include cost benefits due to a minimum stoping development, less ground support, reduced labor requirements, and faster mining rate. Research on the blasting mechanism indi¬cated the method should result in less damage to fill walls than would be normally expected with conven¬tional longhole or large diameter hole cylindrical blast¬ing (benching). This is primarily due to the limited charge weight per delay because of the size dimensions of a spherical as compared with a cylindrical charge and also because the large diameter holes experience less de¬viation than standard-sized longholes. Experience has shown that wall damage has been minimized with the use of this method. The safety aspects of the working environment are also improved as there is no require¬ment for manpower to go under exposed backs after blasting, which is a significant improvement over the cut-and-fill method. CRATERING THEORY General The term cratering, in blasting, is applied to the for¬mation of a surface cavity in a material as the result of detonating an explosive charge in that material. This blasting concept was initially used as a tool in the eval¬uation of explosives performance; however, it has been utilized more recently on surface and to a lesser extent in underground blasting operations. Explosive charges used in crater method are nor¬mally spherical or the geometric equivalent, as research into the application of this breakage mechanism to rock indicates that spherical charges or their equivalent pro¬duce optimum results. In blasting practice, spherical charges have been defined as having a length to diameter (L: D) ratio of 4:1 or less, and up to, but not exceeding a L: D = 6:1. Thus, for holes 165 mm (61/2 in.) diam, a charge 165 mm (61/2 in.) diam, and 990 mm (39 in.) in length would constitute a spherical charge. Crater Testing Crater testing for underground application is nor¬mally accomplished by drilling smaller than production sized horizontal holes into drift walls, placing relatively small charges of explosives in the holes at various depths of burial, firing the charges, and measuring the results. The results are scaled to develop charge weight size and depth of burial parameters for production hole sizes. In theory, this procedure is valid and is appli¬cable for surface blasting; however, in underground applications where the craters are inverted, there is some question as to whether extrapolation of the test results is appropriate. As well as the fact that craters are in¬verted with resultant gravity stresses, testing is often done in a waste rock drift where the properties differ from those in ore rock. There is also some question as to whether a 51 or 76-mm (2 or 3-in.) diam charge behaves similarly to a 165-mm (61/2-in.) charge in a confined borehole. Crater testing at Strathcona involved drilling 76-mm (3-in.) diam holes at various depths ranging from 1 to 3 m (3 to 10 ft). The test holes were drilled in the wall of a predominately waste drift as well as in a stope wall. Charges were placed at various depths of burial, were confined, fired, and the results measured. Although the results were somewhat erratic, possibly because of the aforementioned reasons, they did provide guidelines for basic design for production application. MINING METHOD APPLICATION FOR PILLAR RECOVERY Following initial crater testing, assessment, and tech¬nical evaluation, it was decided to use this blasting tech¬nique in a production application, and to incorporate

Jan 1, 1982

By Patrick D. McLaughlin

Crater blasting techniques have had relatively little application in the surface mining industry. This is not surprising, considering the geometry required to efficiently use cratering. The more widely known blasting operations that employ some form of cratering are listed below.

Jan 1, 1992

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978

The introduction of large diameter holes to underground mining has provided the first opportunity to apply near spherical charges in production scale blasts instead of the convent- ional long cylindrical charges generally used in stope and pillar mining. A modified version of the cratering prin- ciple was applied in the blast design in extrac- ting ore across a horizontal area of a stope or pillar. The new rock breaking technique has developed into the Vertical Crater Retreat (VCR) mining system and eliminated raise boring, slot cutting and dilution of the ore by back- fill material. Furthermore it has reduced labour and time requirements thus becoming not only a low cost method of mining but the safest method of underground mining known today. Exceptionally fine muck is provided with a minimum of damage by blasts to walls and re- treating backs of the stope or pillar. The VCR method can also be used for drop- raising, and for the excavation of underground cavities for almost any purpose . The proper explanation of the breakage mechanism of the near spherical charges opposite to the cylindrical charges yet to be found. The mining industry has quickly recognis- ed the value of the VCR mining method which is being adopted by an increasing number of mines

Jan 1, 1978

By Crazy Horse - The Journal of Explosives Engineering - Vol 20 No 1

The crew at Crazy Horse Memorial has produced a w o n d e rful new video called “The Fine Art of Mountain Carving.” The video closely examines for the first time, the extraordinary explosives engineering on the Crazy Horse mountain currently in pro g ress in the Black Hills of South Dakota. The 56-minute video takes the viewer up the mountain for a behind-the-scenes look at the drilling and blasting crew at work on the mountain. The video was written, edited and produced by Robb D e Wall and is available exclusively from the Crazy Horse Memorial in both DVD and VHS formats. For i n f o rmation, see www.crazyhorsememorial.org The following, is a brief summary of the 25 steps involved in carving the mountain. The video goes into extensive detail on each of the 25 steps. Both those in the explosives industry and those outside the industry will find the video intere s t i n g .

Jan 1, 2004

By Anibal Meza P

Ante la crisis minera desarrollada en el 2001, la planta concentradora de Milpo ha desarrollado una serie de mejoras en sus procesos, donde obtuvo un valor agregado a los productos y la optimización del proceso metalúrgico. En ese sentido, el presente trabajo señala los procesos para mejorar los resultados metalúrgicos y crear el valor agregado a las productos a través del manejo, la implementación y optimización del proceso de separación, de la capacidad en la molienda para mejorar la recuperación del oro, así como del rediseño del circuito de flotación de zinc para reducir la carga circulante y mejorar su recuperación y calidad.

Jul 31, 2003

By Claudia Castillo

Es el caso de estudio del presente trabajo el conflicto que enfrento al Centro minero a cargo de Southern Perú Copper Corporation, sede “Cuajone”, mina de cobre a cielo abierto ubicado en el distrito de Torata, provincia de Mariscal Nieto, departamento de Moquegua, Perú, cuyo yacimiento está localizado en la franja oeste de la Cordillera Occidental en la parte sur de los Andes peruanos, cuyo inicio tuvo lugar el 28 de febrero del año 2022, cuando la Comunidad Campesina de Tumilaca, Pocata, Coscore y Tala tomó control del vaso regulador del reservorio Viña Blanca, del cual se abastece de agua potable al centro de operaciones y al campamento del referido centro minero

Sep 30, 2022

By Justo G. Ramón Rojas

Con la promulgación de la Ley peruana de seguridad y salud en el trabajo, Ley 29783, desde hace cinco años, el objetivo primordial de todas las empresas mineras, fue actuar en pro de su cumplimiento, implantar nuevas estrategias para prevenir situaciones que hasta entonces no se había considerado como factores de riesgo. En definitiva, la preocupación del Estado se centró fundamentalmente, en “que” debíamos hacer para mejorar el desempeño de la seguridad laboral en la búsqueda de mejores condiciones de trabajo.

Sep 1, 2017

By Curt Morgan

This paper will discuss the value of cream a common information model for the mining industry. Information models are a proven technique for quantifying diverse information in a non-proprietary and easily understood manner. Combining information models with emergent data exchange technologies such as XML and SOAP, the mining industry could substantially reduce the costs of sharing information, reduce dependence on proprietary information systems, leverage inexpensive PC desktop technology, and provide a solid foundation for simplifying mine information systems. The paper will provide an overview of information modeling, discuss practical and proven applications of the modeling technique in the mining industry, propose how such a model could be developed in a collaborative manner and discuss the benefits of such an effort.

Jan 1, 2002

AustraliaÆs success as a mineral producer and exporter rests heavily on its technological competence. That competence is based not just on adopting internationally-developed technology but also on ground breaking research conducted at Australian research institutions, many of which have global reputations. A number of forces are now operating to speed the introduction of advanced technology to mining and processing operations around the globe and this will create pressure on the Australian industryÆs ability to retain its competitive edge. Examining the foundations of that national research base and the associated culture of innovation may provide some guide to the dynamics that will be required to maintain technical competitiveness in the future.

Jan 1, 2008

AustraliaÆs strong position as an aluminium producer and potential magnesium producer combined with rapid market growth in the automotive industry, proximity to Asia and other natural advantages points to considerable opportunity for downstream processing and manufacture with light metals in this country. Development of a vertically integrated light metals industry in Australia needs to be pursued with vigour, as does the continued development of global strategic alliances through the value adding chain.

Jan 1, 2000

Project Hobson involves the replacement of an existing 90-year-old above-ground sewer that crosses Hobson Bay in Auckland, New Zealand, and which is nearing the end of its economic life, with a 3 km long, 3.7 m internal diameter segmentally-lined bored tunnel. The $118 M project will offer several benefits to the owner, Watercare Services Ltd, and the local community:provide capacity to meet projected growth in the region,virtually eliminate wastewater overflows into Hobson Bay and the Waitemata Harbour, andremove an obtrusive visual feature and open up the bay for recreational purposes. The geology in the region is a sedimentary formation, which has been significantly influenced by volcanic activity; 49 volcanoes are present within 20 km of the nearby city centre. The geology along the alignment is dominated by two palaeovalleys which have been infilled with a combination of marine alluvium and volcanic deposits. Watercare Services Limited has elected to manage and share tunnelling risk through, among other key measures, the implementation of a geotechnical baseline report (GBR); one of the first uses of this type of document in Australasia. This paper describes the general principles behind the use of a GBR, the development of the GBR used in Project Hobson and some lessons learnt.

Jan 1, 2008

By David Lewin

The journey toward cleaner coal-fired power generation is driven by technological improvements, more stringent regulations around greenhouse gas and other air emissions, and the potential of one of Canada?s most abundant resources. Within this context, EPCOR is leading efforts to commercialize gasification technology to produce electricity with near-zero emissions. By turning coal, oxygen, and water into synthesis gas through a gasification process ? and then capturing CO2 ? it is possible to dramatically reduce greenhouse gas and smog-related emissions. EPCOR is conducting front-end engineering and design work on an Integrated Gasification Combined Cycle technology (IGCC) utility-scale plant ? in conjunction with the Canadian Clean Power Coalition ? at its Genesee site, west of Edmonton. EPCOR, the Alberta Energy Research Institute, and Natural Resources Canada have each contributed $11 million to the $33 million project. A critical element of the project features the capture of CO2, which would be piped underground for long-term sequestration, or for use in enhanced oil recovery (EOR). The combination of IGCC and CO2 sequestration, at this scale, has not been used anywhere else in the world.

May 1, 2008

By I. Nimmo

Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. Communications issues were resolved, better coordination of materials, improved situation awareness during startups, abnormal operations and an opportunity to make improvements during normal operations characterize the changes at the Worsley Refinery. This presentation will review the reasons for the change. Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. This presentation will review the reasons for the change, what changed and the process of changing the culture from reactive to predictive and what difference that has made.

Jan 1, 2011

By Milford L. Skow

This report summarizes the principal activities and results of 15 years of research by the Bureau of Mines, U.S. Department of the Interior, on methane control in coal mines. This research has investigated fundamental factors regarding the occurrence and movement of methane in coal beds, removal of methane prior to mining, and control of methane during mining. The report includes a bibliography listing the more than 150 publications resulting from the Bureau&apos;s methane control program as well as numerous other references, a section on methane recovery and use, a look at the upcoming Bureau of Mines research program, and a brief review of methane drainage practices in other coal-producing countries.

Jan 1, 1980

By Unknown

[Executive Director’s note: According to 17th edition of the ISEE Blasters Handbook in its section on trench blasting, “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underground and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or NOx may travel through the strata and find their way into basements of nearby homes or businesses. The IME has recommendations on how to minimize this potential problem. Some of the points include removing the overburden and digging the rock immediately after the shot, and drilling vent holes periodically between the ditch and adjacent homes.” The Board of Directors of the International Society of Explosives Engineers has expressed its concern that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. What follows are excerpts from “Carbon Monoxide - The Silent Hazard”, an article that was recently included in the Safety Update, Vol. 20, No. 1, 2001, published by Nobel Insurance Services.]

Jan 1, 2002

By Rebecca L. Jones

The paper addresses the application of XPAC AutoScheduler at the Fort Hills Energy Oil Sands Project to complete fast turn around ?what if? scenario testing of different mine schedules. Traditional scheduling approaches involve engineers making a ?best guess? at the required mining sequence, loading this sequence into a scheduling package and testing the results to determine if the schedule meets corporate objectives. This process is iterative and can be very time consuming. Autoscheduling techniques, on the other hand, are based on the engineer pre defining the mining rules and constraints of the deposit. The software then automatically selects a sequence of mining which the schedule should try and achieve, based off specified corporate objectives. Under this system the engineer is able to adjust the objectives and rules to evaluate numerous scheduling scenarios quickly and easily. An XPAC AutoScheduler model was built, documented, and implemented by Runge and Petro-Canada Oil Sands Inc. personnel in a month. It is currently being used by Petro-Canada Oil Sands Inc. to run multiple schedule scenarios, most taking less than ten minutes configure and ten minutes to schedule. The results of each schedule are tabulated with supporting graphs on; the bitumen grade profile, strip ratio, ore inventories and mined tonnage. In addition to this, the block model may be animated to show the progression of the resources mining the schedules.

May 1, 2008

By G M. Young

IT IS most appropriate that this first Memorial Lecture should be given in the Province of Quebec, near the site of the first metallurgical industry in Canada. At La Forge, about seven miles north of Three Rivers, iron was produced in 1783. We are told that the early settlers obtained most of their iron-ware -stoves, kettles, axes and ploughshares -from this smelter, with its foundry and forge. The Canadian copper industry also had its beginnings in Quebec when, nearly 100 years later, in the 1880&apos;s, several small copper smelters were erected in the Eastern Townships. Later, in 1899, Canada&apos;s first aluminum smelter was built at Shawinigan. From these small beginnings has grown a vast metals industry, the export value of its products being only exceeded by that of our forest products -newsprint, pulp-wood and lumber. As we are not a large country in terms of population, our domestic capacity to consume is often small in relation to our developed capacity to produce.

Jan 1, 1963