Search Documents

By G. Bonifazi

The study of minero-petrographical characteristics and the subsequent textural and structural characterization of an ore mineral represents the first step of each industrial processing whose aim is the beneficiation of each valuable mineral phase present inside the ore. Analytical, mineralogical and petrographical, chemical and multispectral image analyses based investigations, applied to eclogitic ore samples deriving form "in situ" sampling campaigns, were applied. These procedures enabled to point out some textural and structural aspects characteristics of ore litotypes belonging to eclogitic-amphibolitic dikes. Such dikes are characterized by a paragenesis constituted mainly by siliceous gangue and accessory "useful titanium minerals" as rutile [TiO2], "pseudolilmenite", ilmenite [FeTiO3] and sphene [CaTiSiO5]. In the beneficiation process applied to ore s is of preliminary importance to establish a strategy in order to obtain a recovery of high quality "mono-minerals concentrates" as rutile, "pseudolimenite", ilmenite and phene. To reach this goal is thus necessary to develop a preliminary study of the textural, structural, petrochemical and minerochemical characteristics of the samples. Different ore samples (eclogitic rocks), resulting from sampling campaigns carried out in the Piampaludo area (Sassello district: Savona, Northern Italy), are examined.

Jan 1, 1994

By D O’Dea, B Godel, T Honeyands, B Ellis, T Harvey

X-ray computed tomography (XCT) is a non-destructive technique that allows the exploration of the internal structure of solid objects in 3D. Over the past ten years, the combination of XCT with more conventional 2D techniques and quantitative 3D image processing and analysis (commonly referred to as digital rocks) has allowed us to address some of the most challenging problems in ore deposit studies. The range of X-ray energies used in XCT allows the X-rays to be transmitted through complex and dense materials including iron ores (eg sinters, lumps, granules). Recent high-resolution XCT scanners have the ability to generate multiscale (25 down to 0.3 µm voxel size) imaging of a given sample enabling the characterisation of 3D textures across a range of scales. This paper will focus on the application of digital rocks to iron ore sinter particles (using filtered polychromatic X-ray beam). The paper is divided into three parts and includes: i) details on the methodologies including their benefits and limitations and the effect of spatial resolution; (ii) the quantification of pore network topology and pore characteristics (eg open versus closed pores, pore size distribution and pore morphologies; degree of connectivity of the pore network and its tortuosity); and (iii) the evaluation of the technique to characterise various phases within the material and quantify 3D mineral textures.CITATION:Godel, B, Ellis, B, O’Dea, D, Honeyands, T and Harvey, T, 2017. Digital rocks for iron ore sinters – towards a D quantification of sinter textures, in Proceedings Iron Ore 2017, pp 529–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Theirry Bernard

The era of non-electric systems as an initiating system has revolutionised the blasting world by introducing a very safe initiating system that is reliable, with initiation sequence possibilities that are superior to those of purely pyrotechnical or electric systems. Electronic initiation has brought with it accuracy, programming and controls that were lacking in the non-electric systems. However, it has also led to a certain degree of complexity, which works against user-friendliness, sometimes introducing a few constraints that are balancing out the intrinsic performance of electronic detonators. The introduction of a hybrid initiation system, Electronic and Non Electric, offers accuracy, and flexibility that were lacking in non-electric systems, whilst removing the inherent complexity of electronic systems. This paper endeavours to summarise the advantages and disadvantages of non-electric and electronic initiation systems that have been recorded after years of experience on site. The paper will then describe how a hybrid system only keeps the advantages whilst eradicating the disadvantages, via a case study.

Jan 1, 2007

By Rana P. Singh

Electrolytic metal reduction operatios in both aqueous and molten salt electrolytes are being studied by digital signal analysis. The purpose is to determine the relationship between the physical processes occurring in the cell and the frequency spectrum of the cell's fluctuating electrical parameters. The fast Fourier transform of cell voltage (in galvanostatic operations) or cell current (in potentiostatic operations) is computed on-line in real time for the electrorefining of zinc in aqueous acid chloride solutions.

Jan 1, 1984

By Thad M. Jones

This paper considers the sampling, digitizing and reconstruction of seismic signals. A sampling frequency range is proposed and a minimum limit is suggested. Digitizing precision criteria for both peak velocity and analysis applications are given. Several methods for reconstructing signals from sampled data are presented.

Jan 1, 1985

By Ham G. I, Just G. D

The model considers a range of design parameters and operating condit- ions and evaluates the significance of these in the ultimate design of a mine. It also considers organizational features associated with the mining method and examines the inter-dependence between operations. An important characteristic of the model is the use of both stochastic and deterministic methods to study the behaviour of the complete mining system. The simulator selects the appropriate unit operation, computes and records its time, performs it and then calculates the production and cost data. Output is in the form of shift, day, week or period repor-ts. These reports will indicate problem areas such as restrictions in the production network for a given set of conditions. The likely effects of alternative means of solving these problems can be evaluated by changing the original input. Such information could be used by the mine management to select an

Jan 1, 1974

By K. K. Cheng, Z. M. Chen, A. L. Mular

INTRODUCTION Since the nineteen fifties, process engineers have been seriously concerned with process models for various purposes (1,2,3). Models serve as subroutines to mathematical flowsheets which simulate circuits of interest. Simulators can serve to increase process know- ledge, assess circuit performance, investigate flowsheet modifications, evaluate new flowsheets, perform off-line optimization, and compare alternative control strategies. This chapter describes a methodology to develop a simulator of a bulk Cu-Mo circuit comprised of roughers, scavengers and 3 stages of cleaning. The simulator was employed to evaluate the influence of water addition at circuit points and to estimate the optimal number of cells for each stage in the circuit. DESCRIPTION OF CIRCUIT Figure 1 is a flowsheet of the Brenda Mines Ltd. (located near Peachland, B. C.) bulk Cu-Mo flotation circuit as simulated prior to an expansion/renovation which involved the installation of large, new flotation cells. Referring to the flowsheet, feed to rougher cells includes fresh feed, scavenger concentrate and 1st cleaner tailing. Rougher con, 1st cleaner (sect ion 2) con and 2nd cleaner tailing are fed to 1st cleaners (section 1). 1st cleaner (section 1) concentrate and 3rd cleaner tailing serve as 2nd cleaner feed, while 2nd cleaner concentrate is fed to the 3rd cleaners which produce a final bulk concentrate. Table 1 lists cell types and specifications important to the circuit. DEVELOPMENT OF MODELS To develop flotation cell models a systematic procedure was employed (4). This involves the selection of responses and factors, proposing models to be fitted, the acquisition of raw data, the statistical adjustment of raw data, fitting models to adjusted data and testing the adequacy of fitted functions. Responses and Factors Responses of interest included recoveries, concentrate grades and concentrate solids/water flow rates for each stage. Factors that influence these responses, such as reagent addition rates, air flow rates to cells, solids and water flow rates to stages and feed grades were not manipulated during the sampling period. Thus, the investigation was limited,

Jan 1, 1986

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

By Gary B. Williamson, Barton K. Cross

Digital simulation is a modern analysis tool which allows the mine operator to evaluate the result of making a decision without actually changing the organization or buying the equipment. The purpose of this paper is to demonstrate the use of digital simulation in evaluating a decision of whether or not to introduce dispatching in an open pit mine. The analysis shows that appreciable savings can be realized by dispatching. In certain cases, an operator can reduce the number of trucks required to move a specified tonnage. A second analysis evaluates the alternatives of using one large shovel or two smaller units. In this case, the operating cost of the haulage equipment necessary to support the shovels turns out to be the critical factor in this decision.

Jan 1, 1969

The trend in the U.S. coal industry in recent years has been a continuous increase in the percentage of coal produced by surface mining methods. Though the predicted energy demands promise a good market for coal, growing legal and environmental issues make the exploitation of a coal deposit by surface methods a difficult and challenging task. Major emphasis has to be placed on the development of integrated mining and reclamation schemes which enhance the possibilities of post mining land uses. Since no major breakthroughs are foreseen in the near future in surface mining equipment, innovative applications of current equipment must be developed. Draglines have been and are expected to continue as the primary earthmovers in surface mining of coal. A dragline simulation model has been developed which has the capability to analyze various deployment schemes such as conventional side casting, advance benching, and extended benching. The mathematical aspects of the model, the input data, and the output results are discussed with reference to an application in an operating mine. The model can be used to select a suitable dragline for given geological and mining conditions and to study the effect of alternative mining layouts and spoiling plans on machine production.

Jan 1, 1979

Digital Simulation of Particulate Processes The inherent complexity of mineral particulates (shape, size and mineralogical texture) has challenged conventional simulation model approaches for decades. Much effort was expedited in using mathematical assumptions to accommodate stereological effect. With the advance of instrumental methods such as x-ray microtomography 3D structure can, in many cases, be measured directly. The information derived from such measurements provides direct input to building the structural digital model. In addition digital simulation methods that enable creation of process realistic particulate properties in an efficient digital computer space have demonstrated their effectiveness to model a variety of realistic packing, sorting and multi-phase processes. The paper reviews recent advances in the use of information derived from 3D micro-tomographic imaging and laser scanning technology can be coupled with digital methods to enable simulation of tablet compaction and dissolution, filtration and permeability, column packing and leaching kinetics, packing and cementation of nuclear waste. By assigning 'properties' to a digital zone (voxel) in the computational space it is possible to mimic the realistic characteristics of quite complex particulate mineral processing systems. The system self-adapts to correct the coherent particle characteristics (shape, size, compound, porosity) with time. Such simulations are useful to elucidate the sensitivity of system performance to variations in process parameters. Dimensional scaling of the approach is also possible, as the case studies will illustrate, in deploying the method to both small (micron) and large (m) features. The use of process realistic simulations presents experimental challenges in code validation. It is in this context that other tomographic methods play a role in direct 3D measurement of system behaviour such as electrical and optical sensors.

Sep 13, 2010

By C. C. Hatch, C. R. Larsen, A. L. Mular

INTRODUCTION As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer/winter of 1975 and during the summer of 1978 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses, to permit study of alternative circuit configurations if desired and to perform off-line optimization. This chapter describes the methodology employed to develop the simulator (1,2) along with typical applications thereof. SECONDARY CRUSHING PLANT FLOWSHEET Figure 1 is a schematic diagram of the Brenda Mines Ltd. secondary crushing plant circuit. The 41,000 tonne coarse ore stockpile(a) is -17.8 cm oversize (3B belt) from two 2.4 m x 6.1 m double deck vibrating screens (not shown). The screens are fed by 2 conveyor belts operated in series with two 198 cm apron feeders that handle discharge from a 152 cm x 226 cm primary gyratory crusher(520 KW). The primary crusher (not shown) treats up to 2725 tonne/hr of run of mine ore. Minus 1.9 cm undersize from the primary screens (#19 belt), referred to as the primary fines, joins secondary screen undersize (#18 belt) for conveyance to fine ore bins (not shown). Feed from the coarse ore stockpile is transferred by means of vibrating feeders and two 120 cm conveyors (#6 and #7) to transfer belts #8 and #9 (Figure 1). The belts feed two secondary 2.1 m standard heavy duty cone crushers (bl and b2). Each crusher is equipped with a modified coarse mantle liner and a standard coarse bowl liner. Mantle throw is 9.2 cm; nominal close side set is 3.2 cm. Crusher .countershafts (443 rpm) are driven by single 260 KW synchronous motors (710 rpm). Discharge from the secondary cone crushers joins discharge from four 2.1 m tertiary heavy duty shorthead cone crushers (fl, f2, f3 and f4). With the exception of the cavity (modified medium mantle liner and standard coarse bowl liner; close side set is nominal .84 cm) and motor (224 KW), these machines are similar to the secondary crushers. The combined discharge is transferred from a 183 cm conveyor to #14 belt which empties into a 1452 tonne secondary screen surge bin (c). Vibrating feeders beneath the bins feed five 2.4 m x 6.1 m double deck vibrating screens (dl, d2, d3, d4 and d5) sloped at 200 from the horizontal. The upper decks are punched plates with 2.7 cm x 7.6 cm slots. Lower decks are woven wire (1.27 cm diameter) sections with

Jan 1, 1982

By J. A. Herbst, A. L. Mular

Digital simulation is defined and simulation techniques are re- viewed. Typical methodology involves the selection of models, the adjustment of raw data, the selection of a fitting strategy, the assessment of model accuracy in a statistical sense, and the development of an executive simulation structure. Simulations serve as aids for process engineers in evaluating the feasibility of a proposed flowsheet and the effect of a modification to an existing flowsheet. In addition, simulation plays an important role in off-line optimization and in the evaluation of alternative circuit control strategies. Several examples are presented to illustrate these uses for simulation including applications in crushing circuits, grinding circuits, and flotation circuits. It is the opinion of the authors that, within the next decade, mineral processing plants will be studied routinely via digital simulation during the preliminary design stage. Simulation will constitute an important component of the design decision making process.

Jan 1, 1978

By H North, J Barringer, S McNeill, D Pairman

Models of ground surface elevation, slope, aspect, curvature, roughness, deformation, as well as other features are gathered together in the term Digital Terrain Model (DTM). DTMs can be generated from a wide range of technologies such as ground surveying, aerial and satellite imagery, including both active and passive sensors. Some elevation derived parameters, such as roughness and slope, can be measured directly using innovative active sensor technology and smart processing, rather than via traditional processing of elevation information. Such models are used as part of a visual interpretation process, and increasingly for computer-assisted analysis using visualisation technology. There is an ever-increasing demand for DTM information to be used in the mineral exploration and mining industry, and consistent pressure from industry to develop models of higher spatial resolution, higher accuracy, and better overall reliability, regardless of the world-wide location of interest. This presentation will survey the range of techniques available for DTM generation, including active (LIDAR, SAR interferometry and differential interferometry) and passive (optical or SAR stereo) methods, as well as interpolation methods (contour or structure interpolation), and the economic placement of these various techniques in the local and regional context. The research issue oftrue-ground elevation models and slopes is also addressed, using LIDAR and SAR polarimetry as signpost technologies. Particular emphasis will be given to the strengths and limitations of new data sources that will, over the next few years, make the acquisition of elevation models of remote regions of the world inexpensive and relatively accurate.

Jan 1, 2000

By Ali Soofastaei

Mining operations are increasingly data-rich yet decisionconstrained. Fragmented systems, variability in geology and operations, and sustainability obligations create multiobjective trade-offs that classic analytics cannot reconcile at operational tempo. This paper proposes an end-to-end framework that fuses digital transformation practices (governed data platform, semantic layer, feature store, and MLOps) with generative AI (retrieval-augmented generation, tool-use, and agentic workflows) and decision intelligence (simulation/digital twins and multi-objective optimization). We formalize sustainability-aware objectives, define a practical stack and governance controls, and demonstrate how an AI “decision copilot” can surface options, quantify trade-offs, and document rationale. Two figures illustrate a production-grade architecture and a Pareto frontier for cost–emissions trade-offs; two tables operationalize decision-domain mapping and a transformation maturity rubric. The approach is product- and company-agnostic.

Feb 22, 2026

By D. Ofstie, B. Kargutkar

BIM, or Building Information Modeling, is transforming the way metallurgical facilities are built, operated and maintained. BIM provides a digital representation of the facility, complete with all physical and functional characteristics - enabling collaborative planning, concurrent design, construction simulation, sustainable operations and predictive maintenance through a connected information model. Building on experience gained in other industries, Hatch is aggressively applying the BIM process to the mining & minerals processing industry to address inefficiencies inherent in traditional document-based information management. Intelligent 3D models support real-time quantity forecasting and cost trending by commodity type and construction work package. By linking procurement and schedule data, material availability and constructability reviews are visualized to verify construction critical path, ensure work front safety and minimize craft downtime. The BIM digital information model connects engineering, construction, commissioning and vendor data, aiding timely asset-centric handover to plant operating and maintenance systems.

Jan 1, 2015

By Alfonso Núñez

The adoption of digital technologies can lower the costs and risks for construction, commissioning, hand-over and transfer to operations eliminate many of the costs and delays associated with handovers and ensure fit for operations deliverables. In Mining, future projects could have 50/30 % less CAPEX/OPEX due to unmanned platforms, remote operations centers, and automated data collection lowering headcount. Additionally, these strategic investments can ultimately become profit centers beyond the traditional ROI paradigm, resulting in a greater return to shareholders/stakeholders for our customer organizations.

Sep 29, 2023

By R. Pipeleers

Recent experience has shown that all underground workplaces in the Campine Coalfield in Belgium will require controlled cooling within three years. Considering the socio-economic and legal importance of the climatic problems underground, IREA has undertaken studies in forecasting the climate of future workplaces, planning the necessary cooling equipment and optimizing efficiency in the existing cooling equipment. These studies are being carried out using the climate forecasting program of Bergbau-Forschung. So far, the German model has been obliged to utilize manually measured data from a few workplaces in the Campine. As the model does not fit very well with these measurements, it has been thought necessary to' develop a system of continuous data acquisition and transmission. This system is being tested in the Beringen mine of the N.V. Kempense Steenkollenmijnen. In the first part of this paper the digital tranmission system is described; in the second the sensors used to collect the necessary climatic data are presented, and in the third some results are given.

Jan 1, 1987

By Yannick Bleuzen, Manuel Joao, Frederic Monath, Miguel Quaresma

The N1 Porto tunnel project is a 650m segment of large-scale civil engineering plan to improve traffic flow between Porto’s downtown district, the Santo Antonio hospital district and the highway access. The tunnel is being excavated into a massive “Granito do Porto” granite structure, 4 – 20m below a highly urbanized environment of Porto, Portugal. The project was originally started in 2000 and was stopped due to the inability to mechanically excavate the granite rock. The city of Porto engineers then turned to traditional drilling and blasting techniques. The use of pyrotechnical delay detonators did not easily comply with the specified environmental and safety requirements concerning blast charging, firing and vibration control resulting in the process taking far too much time. The introduction of digital blasting was proposed to overcome these concerns.

Jan 1, 2005

By Gabriel Andrade Medeiros, Christian Brugger, Paul Pennerstorfer, Daniel Fuchshuber, Reinhold Leitnerl

State-of-the-art automation technology enables digitalization of the continuous casting process that goes far beyond conventional automation of industrial production. Primetals Technologies provides a digital twin that combines an intelligent digital representation of a casting machine as well as the casting process and the slabs, blooms or billets that are produced. It allows metallurgists and process engineers to predict the behavior of the involved complex production process and optimize parameters before using them in real production. New steel grades or production processes can be evaluated off-line without any risks to process stability and product quality. Primetals Technologies installs the digital twin with every new installation of a continuous caster optimization system. This paper describes how the setup and simulation possibilities of the digital twin provide numerous benefits by modelling and simulating the casting process. It allows for example the calculation of material properties according to the actual composition, strand surface temperature profiles and dynamic soft reduction before the final point of solidification. An outstanding feature of the digital twin is the replay functionality provided for various models to analyze and further optimize real production situations. The paper also gives an example how usage of the digital twin optimized production at a customer.

Oct 1, 2019